Should I go for a managed switch?

Hi all,
It's a SBS2K3 network with 2 servers (SBS and LOB) and 65 computers. The SBS2003 will be migrated to SBS2011 soon.
two main switches: Dlink 2x24port, unmanaged. I am thinking to replace them with 1x48port. I am wondering if I should get a managed switch or not. Would a managed switch help troubleshoot network slowness? If so, this can be the reason that convinces
me.
Any thoughts?
Jack

I think a question is how is your LAN configured. One client has 30 workstations and another 20 mobile scanners with Access points. The complex is three building big so we use fiber from server site to each of the two other buildings. From that smart switch
we have 100ft runs to where most of the workstations are.
L2 switches provide easy way to find bad performing mobiles and cable issues.
Other client is all one floor one building and the not-smart 48 port switch is perfect as all new set runs, proper wall mounts and standard length cat6 set runs.
I do like smart switches, more options if you need them, great at start of upgrade and rather have options and not use them that to go back to owner for more money a year from now.
Guzzifrank

Similar Messages

Management port for management switch(2960x) / IP default-gateway for L2 management switch

1)
I am going to connect all mgmt ports of server to this access switch (L2; 2960x) like below. Then I have a management port in 2960x (FastEthernet / L3 port). As you can see below, even though one of Core switch is down, I am able to access through the other Core switch for mgmt SW. Do I need this FastEthernet port of 2960X?
Core Pri ------- Core Sec   (Core Pri 192.168.1.2 / Sec 192.168.1.3 / HSRP VIP 192.168.1.1)
            mgmt SW ----- (FastEthernet0) ------ Goes to where? I don't have RAS (Remote Access Server)
                  |
                  |
      servers' mgmt ports
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_55_se/configuration/guide/scg_2960/swint.html#wp2220949
2) From server side, server put default gateway (192.168.0.1) so if destination is not known, it dumps all to default gateway. This is L3. I understand this. What about L2 default gateway from switch itself? The L2 access switch supports "ip default-gateway" command. I know that without this command still servers do not have any problems to connect to network. Then this command is for switch (2960x) itself? i.e I log into the switch and ping google.com then switch will try to resolve through DNS, but if DNS is not set up in the switch, it sends all traffic to "ip default-gateway"? Is it right?
3) If L2 (Access) switch has multiple data vlans and mgmt vlan (10.0.0.0/24 10.0.10.0/24 192.168.0.1). Then what will be the "ip default-gateway" for this switch?
Thanks for your time and knowledge.
======================== Reference from Cisco regarding ip default-gateway --------------------------------------
How to configure the ip default-gateway command on a Cisco 3550 series switch
VERSION 2
Resolution
To define a default gateway when IP routing is disabled, issue the ip default-gateway global configuration command. Then, enter the IP address of the next-hop router interface that is directly connected to the switch where a default gateway is being configured.
The default gateway receives IP packets with unresolved destination IP addresses from the switch. Once the default gateway is configured, the switch has connectivity to the remote networks with which a host needs to communicate.
Note: When the switch is configured to route with IP, it does not need to have a default gateway set.
For more information, refer to Assigning the Switch IP Address and Default Gateway.
ip default-gateway
https://supportforums.cisco.com/docs/DOC-5090

Vlan 99 is management port. This is an access switch. I am accessing this swtich through SSH remotely (10.1.2.x)
WirelessSWLab#sh ip int b
Interface              IP-Address      OK? Method Status                Protocol
Vlan1                  unassigned      YES NVRAM administratively down down
Vlan99                 10.1.99.35      YES manual up                    up
GigabitEthernet0/1     unassigned      YES unset up                    up
GigabitEthernet0/2     unassigned      YES unset down                  down
GigabitEthernet0/3     unassigned      YES unset down                  down
GigabitEthernet0/4     unassigned      YES unset down                  down
GigabitEthernet0/5     unassigned      YES unset down                  down
GigabitEthernet0/6     unassigned      YES unset down                  down
GigabitEthernet0/7     unassigned      YES unset down                  down
GigabitEthernet0/8     unassigned      YES unset down                  down
GigabitEthernet0/9     unassigned      YES unset down                  down
GigabitEthernet0/10    unassigned      YES unset down                  down
GigabitEthernet0/11    unassigned      YES unset down                  down
GigabitEthernet0/12    unassigned      YES unset down                  down
GigabitEthernet0/13    unassigned      YES unset down                  down
GigabitEthernet0/14    unassigned      YES unset down                  down
GigabitEthernet0/15    unassigned      YES unset down                  down
GigabitEthernet0/16    unassigned      YES unset down                  down
GigabitEthernet0/17    unassigned      YES unset down                  down
GigabitEthernet0/18    unassigned      YES unset down                  down
GigabitEthernet0/19    unassigned      YES unset down                  down
GigabitEthernet0/20    unassigned      YES unset down                  down
GigabitEthernet0/21    unassigned      YES unset down                  down
GigabitEthernet0/22    unassigned      YES unset down                  down
GigabitEthernet0/23    unassigned      YES unset down                  down
GigabitEthernet0/24    unassigned      YES unset up                    up
WirelessSWLab#

Document Types for Case Management Implementation

Hii,
Can any one provide what document types should be used for Case Management Implementation. If possible please describe what is a queue and how it relates to provider group. What is Scripting and how it relates to solution advisor.
Thanks in Advance.
Best Regards!
Deepak P

i got it..for case management..document types will be CAL CL, E-Mail EM, FAX FX, Mail ML. you can create more as per your business needs...

HT1918 I tried to sign for Course Manager and I am from Taiwan cannot use it why? its horrible it should be international here in Taiwan everybody also uses English too.. Apple should understand it very well.

I tried to sign for Course Manager and I am from Taiwan cannot use it why? its horrible it should be international here in Taiwan everybody also uses English too.. Apple should understand it very well. Can anybody guide how can I do or sign inot Course Manager as I am an English teacher here in Taiwan and not able to access the software or Apps because its says TAIWAN NOT AVAILABLE I THINK ITS NOT FAIR AT ALL AFTER SPENDING SO MUCH MONEY ON MY NEW IPAD 64GB

Licensing restrictions or issues.

Plug and Play for Cisco Small Business 300 Series Managed Switch

Good day
what are the Auto-Install options available for the Cisco Small Business 300 Series Managed Switch ?
It would appear there are none, the operating system is not the standard IOS I'm used to.
Would like to use it with Cisco Prime Infrastructure's PnP Gateway capability.
Regards
Pierre

Prime Infrastructure uses and assumes a CNS (Cisco Network Services) agent on the other side when enabling "plug & play". 300/500 Series do not run IOS and does not include a CNS agent, but there is a way to enable auto-configuration. The switches support DHCP Autoconfiguration (using DHCP options 66, 67, and others) whereby they automatically download their config from a TFTP server at boot time. This allows an administrator to put the configs for all the switches on a TFTP server and simply boot a factory-defaulted switch in order to get its config.
Attached is a document showing how this is done.
Hope the information would be of assistance.

Need SNMP MIB files For Cisco SF 300-48 48-Port 10/100 Managed Switch

Hi All,
I need SNMP MIB files for Cisco SF 300-48 48-Port 10/100 Managed Switch.
I have gone through cisco site but not able to get it.
Can anyone please provide me.I have stuck with this.
Thanks
Ram

Hi Ram, yes the MIB can be used. The switches are essentially the same in many regards (especially on a software level).
I do not know the OID for bandwidth. If you're looking for a particular OID may be this tool helps you
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=dot1dTpPortTable&translate=Translate&submitValue=SUBMIT&submitClicked=true
-Tom
Please mark answered for helpful posts

Need SNMP OID for MSTP status in Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch

Hi,
I have configured redundant network using two Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch through MSTP & it's working fine.
I need OID of MSTP status from which I can monitor which Switch is active and which one is in standby mode.
Please help.
Thanks,
Harsha

Hi Harsha,
check these OID's:
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.4.1.9.9.500.1.2.1.1.6&translate=Translate&submitValue=SUBMIT
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=cRFStatusUnitState&translate=Translate&submitValue=SUBMIT&submitClicked=true
Thanks-
Afroz
**Ratings Encourages Contributors ***

Need SNMP OID of MSTP status for Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch

Hi,
I have configured redundant network using two Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch through MSTP & it's working fine.
I need OID of MSTP status from which I can monitor which Switch is active and which one is in standby mode.
Please help.
Thanks,
Harsha

Hi Harsha,
check these OID's:
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.4.1.9.9.500.1.2.1.1.6&translate=Translate&submitValue=SUBMIT
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=cRFStatusUnitState&translate=Translate&submitValue=SUBMIT&submitClicked=true
Thanks-
Afroz
**Ratings Encourages Contributors ***

SG300-28 28-Port Gigabit Managed Switch

I've forgotten username & password of SG300-28 28-Port Gigabit Managed Switch. Is there any to recover them? but I don't want to lose configurations.

Hi Anton,
You can access boot menu and choose password recovery but this option is only accessible via serial console and after you see Cisco logo hit ESC button once.
Once you choose password recovery current password will be ignored during this current session only so the first thing you need to do is to change and save new password. You can use CLI for this:
switch(config)#username cisco password cisco
switch(config)#exit
switch#wr
and you should be ready to go :-)
Aleksandra

View spanning tree configuraton for all the switches in ciscoworks

Hi All,
Is there any way I can see spanning tree configuration for all the switches we have on our networks in Ciscoworks.
Waiting for your kind reply.
Thanks in advance
samir

This can be done from within Campus Manager's Topology Services. Open up the LAN Edge View map, and you should seesome switch clouds on the map. If you drill into one of the clouds, you should see a Spanning Tree option in the right-hand tree. If you expand this, you can visualize the spanning tree for MISTP or even for each VLAN.

Report should prompt me for parameters, please help.

Hi All,
I am using Crystal version 10, So is there any way I can get the behaviour of my parameters as dynamic parameter? I have this requirement because when I am deploying the Report on BO server, and try to open the report from InfoView, it is not prompting me for parameters, rather it is giving me the copy which we had scheduled earlier. To get the fresh data with different parameters, we again need to schedule the report.
What I want is simple, Whenever user clicks on the report link in infoview, I should be promted for the parameters my report is using.
Please help..
Thanks
-Azhar

Hi
It would prompt whenever it's refreshed.
You can refer to Business View manager guide from [here|http://help.sap.com/businessobject/product_guides/boexir2/en/xir2_bv_admin_en.pdf ] for detailed information.
Hope this helps!!
Regards
Sourashree

Specific Identification Cost for batch managed items (Follow-Up from P2P)

Specific Identification Cost method is used for serial and batch managed item. Using this method, the outbound cost of such items would be the original cost of specific goods, which can be determined according to the serial or batch number of that item.
Business One allows the user to receive batch managed items with a batch number that already exists in the DB. Its possible that the received quantity is added to on-hand quantity in the warehouse. In such case, the quantity on-hand of that batch and the received quantity may have different costs.
What should be the system behavior in such case:
1. Block receipts to the same batch with different costs.
2. Write the difference to a price difference account, as done in Standard Cost method.
3. Manage the batch cost with Moving Average method.
This thread is continuation from 'Specific Identification Cost for batch managed Items' <a href="http://p2p.sap.com/businessoneforum?type=join&login=1&uid=41FB661A76CED536C825C4E2B6FF4397&cid=91&go=z37225">discussion</a> in P2P SAP Business One Forum (Product Development Collaboration).
Previous discussion on P2P is summarized in the attached file.

Hi Peter,
This is a very important functionality that you are describing here. For example, in the Steel industry, it could be extremely useful to cost by batch or serial number.
If you receive a batch that already exists in the system and if the costing method for the product is moving average, then teh cost of the batch should be calculated based on the moving average as well.
If the costing method is standard, then the cost should go in a variance account.
If the costing method is FIFO, then it is a getting trickier...
Regards,
Vincent

Restrict read/edit access for a Manager, when Manager Visibility is enabled

Customer wants to restrict read/edit access for a Manager on his/her subordinates' owned record, if manager Visibility is enabled at the company level.
For example: If SM1 is a manager of SR1 and SM1 owner profile says that he has Edit Access on his owned records then, he will get Edit Access
on the records owned by his sales rep.
Current requirement here is Manager should not be able to edit the records of his sales rep but should able to only View. And manager also
need the Edit/Read access on the records which they owned.
Is there a possible workaround ?

I have devised this to our customer:
First, create a custom text field named "Reports To" on the object, say, Accounts.
Second, user JoinFieldValue to set a default value for the "Reports To" field: equal to the "Reports To" User field value for the current owner.
Third, add a new value named "Manager Read-Only" to 'Account Type' picklist. make sure that this picklist value is active.
Fourthly, add a new page layout marking all Account Fields as 'read-only' and name it "Account Read-Only layout".
Fifthly, create a new Account Dynamic Layout and set "Account Read-Only layout"
for Field Type = "Manager Read-Only".
Sixthly, create a new workflow rule condition for Account object ( before modified record saved ). Use the workflow rule condition similar to UserValue('<Alias>') = [<ReportsTo>] and set the workflow action to update 'Account Type' picklist value to
"Manager Read-Only".
This is just an example. Customer needs to improvise on this.
Any more suggestions please ?

Credit block should not require for Credit card paid sales order

Dear friends,
my client want that sales oder with credit card payment should not block sales order for credit management reasons. Hoe can it be configured.
Regards
rdc

Are you using credit card processing in SAP to get the authorization?
If you are then the authorization should not block the order.
Or are you using credit card as a form of payment (without authorization) in which case this needs to be put on the customers account as a payment and then the order entered.
Where are you holding the credit card details?

Linking DMS to a Content Repository for Recipe Management

How do I link a document type to a content repository?
This is for Recipe Management. When I look in DC10 I can see that there is a document type of RMS for Recipe Management.
I assume this means Recipe Management is connected toDMS
I have created a content repository ZRM using OAC0.
How do I make the link between the document type RMS in DMS and the content repository ZRM?

Thanks for the reply but it isn't really what I was after.
I am only the basis guy so I am not sure of the application but my expectation is that users will save a document with a document type of RMS. This document should be saved to a Content Repository
What you have described is how to save a type of document such as MS Word to a particular repository. I was hoping that Recipe Management documents (possibly MS Word, possibly not) would go to a Recipe Management Repository.
There still might be the possibility that documents (possibly MS Word) for other projects e.g. packaging could be written to a different repository.
What I am hoping for is a link from the document type RMS in DC10 to the Content Repository defined in OAC0.
I have a suspicion this is via the category defined by OACT.
The link from SAP DMS to Content Repository seems fundamental to me. I am surprised no one has the answer
...or perhaps I have completely missed the point?
Tony

Should I go for a managed switch?

Similar Messages

Maybe you are looking for