Should my PSU be enough for this system?

My system is in my rig, but my antec true power 430w cannot boot it up. If I remove the 9700pro and use a different video card, it works fine. Ocassionaly, if I am lucky, it will boot with the 9700.
If I need a new psu.. what are some suggestions? Want to stay under $100 but, i definitely do not want a POS PSU.

Quote
Originally posted by Raven
o8tm33l
your lucky.
psu is a very important device today and weak psu cant provide clean power.
and you should never load a psu to more than 70% which you have done.
its because a computer does not use a even amount of current but it goes up and down rather much.
Quote
well.. if I unplug the power to my video card.. the machine turns on.. when I plug it back in, it just spins for a few seconds and shuts off.
could be overload.
tried the card in another computer to rule out a faulty card ?
oops pressed the wrong button

Similar Messages

Is a Corsair AX850 sufficient enough for this system?

Is a Corsair AX850 sufficient enough for this system or should I go for the AX1200? Everything is at stock.
Motherboard: MSI P55-GD65
CPU: Intel i7 860
Graphics cards: 2x MSI GTX 560 Ti TwinFrozr II OC in SLI
Memory modules: Corsair Dominator DHX 4x2GB@1600 Mhz
Hard disks: 3x Samsung F3 1TB + Samsung F3 2TB
Sound card: Creative X-Fi Titanium
System fans: 7x Tacens Ventus 120mm fans
Disc player: Lite-on iHES 106 Blu-ray player

Quote from: Svet on 14-February-11, 23:03:03
don't use such power calculators, they often tell a rubbish and gives bad advices.
I don't trust them for 100% that's why I asked for advice on this forum.
I'm a pretty experienced PC builder and user but I'm not really familar with the new Geforce 560 Ti cards, only that I know that they are power hungry so I need a new power supply to replace my 600 watt and I always wanted a modulair power supply so now is the moment to do that.

Is CM RealPower 620 good enough for this ?

P35 Platinum Combo
E8500
N9800GT 1Gb (MSI)
2x2Gb ddr2-800
1x sata2 hdd
1x sata dvdrw
2x case fan
Is CoolerMaster 'Real Power 620W' PSU good enough for this setup ?
(Doesn't have PSU's specification at the moment)
Thanks

Cas, you have the coolermaster extreme power. There has been an issue with some models of coolermaster Realpower PSUs. I could re-state the reasons, but Bosskiller has addressed this several times.
https://forum-en.msi.com/index.php?topic=120494.msg910400#msg910400
Quote from: Bosskiller
Quote from: mine0000 on 06-October-08, 02:09:39
The Cooler Master has been working just fine for more than a year with a ASUS P5N32-E SLI Plus and an Intel Q6600. The Antec P450 works fine there too. So why should I believe you (no disrespect intended)? What is the specific grounding issue with the Cooler Master? Can you give me a URL to the issue at their support site?
Thanks.
Yep:
https://forum-en.msi.com/index.php?topic=118911.msg897491#msg897491
https://forum-en.msi.com/index.php?topic=114534.msg858727#msg858727
https://forum-en.msi.com/index.php?topic=113573.msg850339#msg850339
https://forum-en.msi.com/index.php?topic=113170.msg846719#msg846719
https://forum-en.msi.com/index.php?topic=113573.0
https://forum-en.msi.com/index.php?topic=115623.0
https://forum-en.msi.com/index.php?topic=115623.msg869135#msg869135
https://forum-en.msi.com/index.php?topic=118959.msg897790#msg897790
http://forum.coolermaster.com/viewtopic.php?p=79607
Quote from: Ven on 07-August-08, 03:23:06
Wow are you serious..? Man that sucks...I hope I can get a return on it, damn.
EDIT: I spoke with there customer support line, they said they could RMA the power supply with a new revision that works with the board, I don't know what I'm going to do though.
Regardless if you get an updated model which has addressed the compatibility issue, you are better off with a single +12V rail PSU like the ones I suggested.

No JRE version found in launch file for this system

Hi,
I have an application which is launched by JWS.
When we use JWS from 1.4, it runs fine. But JWS from 1.5.0_15 gives the error "No JRE version found in launch file for this system"
In both the JWS(1.4 and 1.5.0_15)cases, we install JRE1.5.0_15 using the installer and used for invoking the application.
We invoke mailclient.jnlp, which inturn invokes the installer.jnlp and KanaJreInstaller.asp
<<mailclient.jnlp>>
<?xml version="1.0" encoding="utf-8"?>
<jnlp
spec="1.0"
codebase="http://mpshanmu-gx520:80/10r3/"
href="mailclient.jnlp">
<information>
<title>KANA Agent</title>
<vendor>KANA Software, Inc.</vendor>
<homepage href="http://www.kana.com"/>
<description>KANA Suite 10.3.0</description>
<icon href="images/mail_logo.gif"/>
<offline-allowed/>
</information>
<security>
<all-permissions/>
</security>
<resources>
<j2se version="KANA1.5.0_15" href="KanaJreInstaller.asp"/>
<jar href="lib/mailclient_s.jar"/>
<jar href="lib/link_s.jar"/>
<jar href="lib/spell_s.jar"/>
<jar href="lib/ssce_s.jar"/>
<jar href="lib/kc_framework_s.jar"/>
<jar href="lib/kc_sharedGUI_s.jar"/>
<jar href="lib/xalan_s.jar"/>
<jar href="lib/xerces_s.jar"/>
<jar href="lib/java2com_s.jar"/>
<jar href="lib/jgl3.1.0_s.jar"/>
<jar href="lib/rsrcbundle_s.jar"/>
<jar href="lib/response_s.jar"/>
<jar href="lib/HTMLEditorEnterprise_s.jar"/>
<jar href="lib/jakarta-oro-2.0.4_s.jar"/>
<jar href="lib/jdic_s.jar"/>
<extension name="Sun Libraries" href="sunextensions.jnlp"/>
</resources>
<resources os="Windows">
<nativelib href="lib/windlls_s.jar"/>
<nativelib href="lib/jdic-native.jar"/>
</resources>
<application-desc main-class="kana.mail.wkstn.AppMain">
<argument>-serverlist</argument>
<argument>http://mpshanmu-gx520:80/10r3/servers.xml</argument>
</application-desc>
</jnlp>
<<KanaJreInstaller.asp>>
<%@ language="vbscript"%>
<%
Response.ContentType="application/x-java-jnlp-file"
Response.AddHeader "x-java-jnlp-version-id","KANA1.5.0_15"
dim fs,f,ts
set fs=Server.CreateObject("Scripting.FileSystemObject")
Set f=fs.GetFile("C:\Program Files\KANA\KANA Response Web Server_10r3\installer.jnlp")
Set ts=f.OpenAsTextStream(1)
Response.Write(ts.ReadAll)
ts.Close
set ts=nothing
set f=nothing
set fs=nothing
%>
<<installer.jnlp>>
<?xml version="1.0" encoding="utf-8"?>
<jnlp
spec="1.0"
codebase="http://mpshanmu-gx520:80/10r3/"
href="installer.jnlp">
<information><title>KANA J2RE 1.5.0_15 Installer</title>
<vendor>KANA Software, Inc.</vendor>
</information>
<security>
<all-permissions/>
</security>
<resources>
<j2se version="1.3+"/>
<jar href="lib/installer.jar"/>
<jar href="lib/JRE_KANA1.5.0_15.jar"/>
<property name="jre.container" value="JRE_KANA1.5.0_15.jar"/>
<property name="jre.execute" value="bin\\javaw.exe"/>
<property name="jre.version" value="KANA1.5.0_15"/>
</resources>
<installer-desc main-class="JREInstaller"/>
</jnlp>
Thanks

>
We are using sun JRE(1.5.0_15) only. We extract Sun JRE and build it as KANAJRE.jar and signing.>I have never heard of KANAJRE. Would you care to post a link to the site, or should we just keep guessing? (My patience for random guesses is running out.)
>
We install using Intaller class and that is getting listed in the Java Control panel and enabled too.>List as what?
Does it list it with the entire string "KANA1.5.0_15" or is is just listed as "1.5.0_15"?
Because this line from the JNLP file..
<j2se version="KANA1.5.0_15" href="KanaJreInstaller.asp"/>..had me convinved it was a non-Sun JRE. Not so much the href, but most especially the version attribute.
If it really is the Sun JRE, I would expect this to work.
<j2se version="1.5.0_15" href="KanaJreInstaller.asp"/>And as an aside. If this installer is giving you trouble and the app. requires the 1.5.0_15 JRE, why not simply the default Sun JRE installer? What advantages do you think this installer offers?

RSA1 error Logical system name has been changed for this system

Hello All,
Earlier the RSA1 was activated for client 300 on our crm 5.2. after that we changed the client to 500 using SE16 -> Type table RSADMINA / Check Colum BWMANDT -> 500.
But now when we login to client 500 and execute RSA1 it is showing
Logical system name has been changed for this system"
In scc4 we have not made any changes. Can you tell what should be done ? in the pop up it is showing following steps
Change the name of the logical system (table T000) for client back to SIDCLNT300. This enables you to continue working with the system.
If you really want to change the logical name, than you can, if and when you:
change the system name back to SIDCLNT300,
delete all existing connections between this system and other systems,
delete all transfer structures that still exist, and
do not use ALE or Workflow.
Guys do you know how to fix this ? .
Also do you know Assignment of Source System to Source System ID (table RSSOURSYSTEM) using RSA1 ?
Edited by: Sahad K on Mar 17, 2008 10:55 AM

Hello Hari,
Both the options you said cannot be used
since the logical system SIDCLNT300 is used by client 300 and it cannot be given to client 500. Also there already exist a logical system SIDCLNT500 which is assigned to client 500.
I found out the issue. In the table RSBASIDOC the logical system name that can use rsa1( bw client )is set as SIDCLNT300). Only if we delete that entry and set it to SIDCLNT500 ( 500) we can use it on client 500.
The solution is specified in /message/3284842#3284842 [original link is broken]
Let me try the solution 2 and inform you.
Solution 2:
You cannot delete the source system. Two cases have to be distinguished:
The source system still exists.
Switch to Transaction SM59. Find the destination which has the same name as the logical system of the source system from field SLOGSYS in table RSBASIDOC (see above).
Such a destination does not exist in Transaction SM59. In this case, you have to create the destination to the source system. Name the destination equal the entry in SLOGSYS from above. Then return to the Administrator Workbench and repeat the deletion.
The entry exists but a remote login is not possible. Correct the communication parameters.
Everything works. Change to Transaction SE37, function module RSAR_LOGICAL_SYSTEM_DELETE, Sngl. test. Parameter I_LOGSYS = <log. name of the source system>, I_FORCE_DELETE = 'X'.
The source system no longer exists or was replaced with another source system with the same IP address.
Proceed as described in the first case but make sure, that the field 'Target host' contains a not existing server in the maintenance screen of the destination (Transaction SM59). If necessary, change an existing entry. Later when you delete, the system asks you whether you want to delete, although the source system is not available. Select 'Ignore'.
Incase you have any idea other than this please let me know how to edit the RSBASIDOC table and change the entry to client 500.
Edited by: Sahad K on Mar 18, 2008 5:07 AM

Debliery Units : VENDOR IS NOT DEFINED FOR THIS SYSTEM

Dear Experts,
In prespective modeler , tried creating 'DELIVERY UNITS'. However get error message
"CANNOT CREATE DELIVERY UNIT AS CONTENT VENDOR IS NOT DEFINED FOR THIS SYSTEM" ?
How can we maintain CONTENT VENDOR ? we are using in-house HANA installation.
Regards
Prashant

Hi Shrikant,
Please do not reply with your same question in all of the threads which are answered.
What is the version you are using?
Where exactly you are unable to see?
Once you edited the field as mentioned by Jody, it will be in green circle. Also while creating the package, you can see this DU as shown below:
Regards
Raj

Xml contains no components for this system.

Good Morning Sap Experts
I am aplying EHP1 to SAP NETWEAVER 7.01 and I get the error
The stack /usr/sap/trans/SMSDXML_PBI_20100831232419.708.xml contains no
components for this system.
Now I review the XML file and the JAVA STACK don't appear in xml file.
Only appear the ABAP STACK, I tried to recreate the file but the problem persists

SOLVED, I set the system in solution manager stcode SMSY
BI 7.0
1. Create a system component of type Java system with name beginning with the 3 letters of the SID of the j2ee engine where the BI Java is running.
For software component, click on the from MainInstance button and then select Product SAP Netweaver, Product version = SAP Netweaver 7.0 and Main Instance BI Java.
2. Enter a system name beginning with the 3 letters ofyour SID (Abap stack).
Select Product = SAP Netweaver, Product version = SAP Netweaver7.0
In the table, check the Business intelligence (BI) as relevant.
Double click on it and enter the Instance and server names. Check the BI Java as relevant and then enter the System
Component that was previously created in the System component column, and check the box in the system Component Assignment column, in the column type, select Java system.
3. Recreate XML file and rename it.
Thanks
William Neira

BI Error Logical system name has been changed for this system

Hello All,
I have installed the BI system and did a client copy from 000 to 200 client with profile SAP_ALL.
Now I have loged into the system with client 200 and wen I run RSA1, I am getting the following error
message: "Logical system name has been changed for this system"
Thanks
Sekhar..

Hi,
Goto tcode SCC4.
Switch to change mode. (System will prompt that this table is cross client. Continue)
Select your client (in this case 200). Click on details button (next to change mode button)
Enter the proper logical system name in Logical system field.
Click on Save button.
Then try RSA1.
Hope it helps
regards,
Pruthvi R

Unable to release package administration lock for this system

Hi,
I created a Solaris package, but at the end of installation (on a Solaris 10 sparc) I get :
#pkgadd -d MyApp_version__SunOS_sparc.pkg
Installation of <MyAppName> was successful.
pkgadd: ERROR: ERROR: Unable to release package administration lock for
this system; try again later
pkgadd: ERROR: ERROR: Unable to release package administration lock for
this system; try again later
The solution is to delete:
#rm rf /tmp/.ai.pkg.zone.lock*
Then some lib issues occur .. fixed by:
#cd /usr/lib
#ln -sf ../../lib/libdlpi.so.1 libdlpi.so.1
Then I can install and uninstall without any problems as many time as I need.
Why does this issues occur when the package is first install on a system ?
Thanks,
Bianca

Hi Alan,
In the postinstall script I only handle the configuration files that my application has (all the files are in the /app/MyApp directory, no system files involved). I use the read user input and replace the values in the config file, and create another 2 files (also in /app/MyApp directory). This is all I do.
I use the packaging scripts: depend, copyright, pgkinfo, preinstall, request, postinstall, preremove, postremove
Thanks,
Bianca

Infamous "Recovery policy configured for this system contains invalid recovery certificate" message

Hello,
On a Windows 2012 R2 member server of a Windows 2012 domain, I tried encrypting a folder, and I got a "Recovery policy configured for this system contains invalid recovery certificate message." This is the first known attempt
at enabling EFS within our organization.
When I looked at the EFS certificate within the Default domain GPO, it had expired.
Is it as simple as deleting and recreating the EFS certificate within the Default domain GPO? Then running gpupdate /force on the Windows 2012 member server?
Thanks
Ron

You can give a look to that: http://blogs.technet.com/b/askds/archive/2008/01/07/replacing-an-expired-dra-certificate.aspx
More if you ask them here: https://social.technet.microsoft.com/Forums/windowsserver/en-US/home?category=migratedforums&filter=alltypes&sort=lastpostdesc
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Is the PXIe-PCIe8361 adequate for this system? And external clock questions...

Hi all,
I have spent some time piecing together a system and I'd like a sanity check before pulling the trigger on this purchase. The system will contain the following hardware:
1. Chassis: PXIe-1078
2. Controller: PXIe-PCIe8361
3. 3 x PXIe-6363 (16 analog inputs each card, 32 digital inputs each card, all internally clocked @ 10kHz)
4. 2 x PXI-6224 (32 digital inputs on one, 8 digital inputs on the other, externally clocked in "bursts" of 62.5khz)
5. Labview software
The three PXI-6363 cards will be responsible for a mix of analog and digital measurements made @ 10 kHz, timed continuously by the onboard clock.
One PXI-6224 will be clocked externally @ 62.5 kHz and will be used to collect digital data on a 32-bit port. These clock pulses will not be continuous, but will occur in bursts lasting for 2ms every 20ms.
The other PXI-6224 will be clocked externally @ 62.5kHz as well and will be used to collect digital data on an 8-bit port. These clock pulses will not be continuous, but will occur in bursts lasting for 2 ms at random intervals.
My questions are:
1. Am I planning anything that looks unreasonable for this hardware?
2. Should I expect issues with data transfer rates with the PXIe-PCIe8361? I will be operating well within the advertised 110MB/s throughput of the device. I plan to stream this method... NI Fast TDMS data streaming
3. I have only ever used NI cards for continuous measurements made by an onboard clock. When I set up a task to collect data that is externally-timed, will the DAQ be expecting a "continuous" clock pulse, or will the system wait patiently for clock pulses to arrive at any rate (any rate within the spec of the card, of course)?
Thanks, any input is appreciated.

Hello LucasH0011
1-As long as you put the PXI-6224 and the PXIe-6363 cards in the corresponding slots, meaning the express(PXIe-6363) in the express and the hybrid(PXI-6224) in the hybrid.
2-I think you would not have issues with the transfer rate.
3-Your timing specifications sound reasonable to me, I think you will be fine.
Here is a document that has useful concepts for the use of cards:
http://www.ni.com/white-paper/3615/en/
It is for the M-Series, but the concepts apply to the X-Series as well.
Regards
Ernesto

Logical system name has been changed for this system

Hi gurus,
I am fasing problem in BI7 system. we created a new client in the system & want to set it for BI development.
System Response
The transaction is canceled.
Procedure
Change the name of the logical system (table T000) for client back to BID500. This enables you to continue working with the system.
If you really want to change the logical name, than you can, if and when you:
change the system name back to BID500,
delete all existing connections between this system and other systems,
delete all transfer structures that still exist, and
do not use ALE or Workflow.
Regards,
Darshan..

Sorry, BI is a one client system. You cannot have a prod client and a dev client within one SAP system.
But...
...NO, you can't!
Best regards
Michael
EDIT: just to add, there is an exception if you have a SCM/APO type system [522569 - BW: Working in several clients (especially APO 4.x/SCM 4.x)|https://service.sap.com/sap/bc/bsp/spn/sapnotes/index2.htm?numm=522569]

Toolbox not licensed for this system (T400s)

Thinkvantage Update found that an update for Toolbox (6.0.5692.08) was there and it was chosen to install it. The old version - which worked ok albeit a bit slow - was uninstalled and the new installed. After starting it from the taskbar it comes with this: "This version of Lenovo Thinkvantage Toolbox is not licensed to run on this system". Which is win7ult64 and the older versions worked fine... ffs....
What does this mean? There is almost 600 days left of guarantee and ThinkUpdate usually works. So is there any other solution than going back to the old version?
The machine in question is a T400s 2815-3SG with 4GB RAM installed by a Lenovo dealer: Only difference to a stock system is that a 4GB SD-card is used by windows as readyboost.
Thanx in advance for your reply!!
Solved!
Go to Solution.

So did I - and that didn't work here... but after uninstalling, a restart, a new instance of Update that found the new toolbox - let it install this (and it did without failures) starting the new Toolbox which found after start that an update was available. Installing this - and 'lo and behold!!! - it worked!!!
So now: Problem solved

How should i write a pcr for this requirement?

Dear Friends,
       Can any tell me whether we can write a pcr in such a way that if the person resigns the company on any day after 15th his full absence quota(for that month) should be accrued.
      if yes can you tell me
      what are the key decision parameters i have to use in writing the pcr.
        waiting for you kind reply.
Regards,
Sai Prasad.

Hai Prasad,
I can give you the logic, cannot write exact rules.
While genegarting absence quota
- Check for termination action using OUTWPMASSN
    - If yes
          Check for Action year current year. (HRS=YSAY, HRS?CURYR)
              - If its equal to 0
                  Check for current month (HRS=YSAO, HRS?CURMO)
                       - if its equal to 0
                              check for current day (HRS=YSAA, HRS?CURDY
                                    - if its >=15
                                         generate quota
                       - Exit
(Note: for this logic you have to generate monthly quota)
With regards
Shyam V

XPS8700 - I'm lost on audio for this system

This system is exactly one year old now and I've never connected any speakers to it - partly because I don't understand what types will or could work with it.
The original printed system configuration indicates that my sound card is "Integrated 7.1 with WAVE MAXXAudio 4." In Device Manager, I see "Realtek High Definition Audio." Nowhere do I see an actual sound card model name/number, etc. So - I don't even understand what I've got here from an audio standpoint.
What I currently have for speakers - left over from a previous system - is just a couple of Labtec desktop speakers and a Harmon/Kardon sub. I'd like to know if it's possible to use them with this system and, either way, I'd love suggestions on something better that would take advantage of this system's capabilities.
Thanks for any help!

I forgot to include in my post that I had downloaded the new flash after the "no audio" began and it did not help. The problerm began some time after I installed OS 10.7.4.

Should my PSU be enough for this system?

Similar Messages

Maybe you are looking for