Show detailed system message in Analyzer by default
Hi all,
when using 7.0 queries/workbooks in BEx Analyzer, you get a popup displaying the system messages when logging on.
By default only the first line of the system message is shown. By clicking the 'Details >>' the whole message can be shown.
Now, is it possible to show the whole message by default?
So that the popup window with the system message is expanded by default?
Hi,
You created Condition type XXXX and assigned the same to a pricing procedure(Example :RM0000)(M/08) and made that codition as Mandatory in M/08 but not appearing in PO. Now check the condition type in M/06 and see did you select exclusion indicator in "Control data 2" segment, if yes , just remove that indicator & keep as blank and save.
Also keep Manual entries as No limitation in "Changes which can be made segment" & save.
Now try to create PO , you will have Condition type XXXX in the PO.
Regards,
Biju K
Similar Messages
-
DSEE 6.3: how to show detailed error messages to ldap clients?
Is there any possibilty in DSEE 6.3 to send to ldap clients detailed error messages about - for example - missing required attributes in ldap add operation?
I don't have access to ldap server's logs, so I loose a lot of time trying to figure out "which of 40 attributes I sent to server is bad?"...Thank you for reply.
I know that I can view schema, but I need the functionality which is available in relational databases. When I try to store bad field value in database table, I get descriptive error message: "field XYZ has bad value". In DSEE I get "schema violation" or other cryptic message.
It's very hard to track the problem if you operate on 30 or more attributes. Which one causes error?
I see that this functionality is available in DSEE backend (error logs are descriptive). How to turn on this for clients?
If it is not possible, I will try to write special software module which will double DSEE functionality and check attributes before storing them in DSEE. -
How can I see in EP7.0 a system message placed in ECC 6.0 ?
Hi everybody. I have one question. We have an EP 7.0 and one ECC 6.0 . In older versions 4.7 there is an IAC called sysmsg that you can use to show the system message you have placed in the ERP server through an iview in the portal. IT´s really usefull for the users in order to take care of notifications like "Travel Application is blocked for 2 hours" or whatever kind of messages you want to show to end users.
I´ve been reading ALL the threads I could found about this , but I can´t find the answer. I don´t want to send a broadcast message to all EP users, I only want to show the system messages that you put using SM02 in the ERP but in an iview in the portal.
Any ideas?
Thanks in advance and best regards.Hi Jose
Please see the following Wiki's for some help with this
Brodcast messages to logged on users in Portal(Part1)
Brodcast messages to logged on users in Portal(Part2)
Best wishes
Stuart -
IIS8 to show cf11 error messages
I just migrated to windows 2012 and cf11.
I'm trying to get IIS8 to show detailed error messages relating to CF errors.
I've found a lot of documentation relating to cf10 and iis7... but it looks like it all leads to dead ends and doesnt work.
Right now on any coldfusion 500 error, I am displaying:
ERROR
An error occurred while executing the application. Please try again or contact the administrator.
It would be great if I could show the CF error to help me troubleshoot the migration headaches a little faster.
thanks
steveThanks for the reply. Yes I had ran the web server configuration tool.
After some trial and error, I viewed the source of the error that we being delivered to me and it had referenced to images in a cfide folder, so that indicated to me that a CF error was being displayed and it wasnt being intercepted by IIS.
So I went back into the debugging and logging tab and fooled around with the settings a little more and it eventually started to work as I expected. -
Oracle: SQL Workshop needs the SYSTEM MESSAGE to show up..
Hi Oracle Dev Team,
We have 3-4 environments as most of us do...
DEV, TEST, UAT, PROD
When I am in UAT SQL Workshop and then get distracted from phone call etc
I come back and start working on a DEV issue BUT I forget I am in UAT.
The SYSTEM MESSAGE shows up when you go to SQL Workshop area but when you go into the SQL Workshop > SQL Commands window its gone.
also the other windows as well:
Object Browser
SQL Commands
SQL Scripts
Query Builder
Utilities
Any way to distinguish between environments?
Thanks, BillHi Bill,
We follow a standard for 'Developer Usernames' in our workplace. We always post fix environment details to our user names, like BILL_DEV, BILL_UAT etc. So if you follow similar standard, you can always point out in which environment you are, just by seeing the welcome message at upper-right corner of your screen. It's not the technical solution, but still it will serve your purpose.
You may check-out "Background Image depending on Connection" section in following site, if it might help.
http://builderplugin.oracleapex.info/
Regards,
Hari
Edited by: Hari_639 on Jan 20, 2011 3:51 PM -
System Message Shows in Future Date
Dear Experts,
In Our SAP BI System , The System Message SM21 shows in Current & future date both problem messages
SAP Server OS and SAP BI Application Time and date both are in sync
The BI system which is connected to ECC PRD also having a sync
Remote monitoring are not configured in this system,
System Log: Local Analysis of GEEPASBIPRD 2
Date : 22.12.2010
Time Type Nr Clt User TCode Priority Grp N Text
10:02:54 DIA 001 350 GPKWTHOFI03 BY E Invalid parameter ObjTooLar
10:04:07 DIA 001 350 GPKWTHOFI03 BY E Invalid parameter ObjTooLar
System Log: Local Analysis of GEEPASBIPRD 3
Date : 02.01.2201
Time Type Nr Clt User TCode Priority Grp N Text
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:90 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
20:20:90 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
40:20:81 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
71:31:41 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
71:31:41 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
90:20:84 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
System Log: Local Analysis of GEEPASBIPRD 4
Date : 03.01.2201
Time Type Nr Clt User TCode Priority Grp N Text
00:20:85 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
00:20:85 35 BIWREMOTE hB Y Missng:TSL1TE,hBY):154 EXE
System Log: Local Analysis of GEEPASBIPRD
C o n t e n t s
Content Page Start End
Selection criteria 1
2 22.12.2010 10:02:54 22.12.2010 10:04:07
3 02.01.2201 20:20:84 02.01.2201 90:20:84
4 03.01.2201 00:20:85 03.01.2201 00:20:90
5 02.01.3201 01:23:65 02.01.3201 90:40:42
6 03.01.3201 00:40:41 03.01.3201 11:62:24
7 02.01.4201 01:22:30 02.01.4201 90:40:42
8 03.01.4201 00:40:41 03.01.4201 11:62:24
9 02.01.7201 11:42:21 02.01.7201 31:71:95
10 02.01.9201 01:22:30 02.01.9201 81:41:10
11 03.01.9201 00:95:23 03.01.9201 11:11:94
12 02.01.A201 01:22:30 02.01.A201 81:41:10
13 03.01.A201 00:95:23 03.01.A201 11:62:24
14 02.01.E201 11:24:13 02.01.E201 71:50:52
15 02.01.I201 01:22:30 02.01.I201 81:41:10
16 03.01.I201 00:95:23 03.01.I201 11:62:24
17 02.01.R201 01:22:30 02.01.R201 81:41:10
18 03.01.R201 00:95:23 03.01.R201 11:62:24
Contents 19
Thanks
JaiHi Thahir,
I deleted the SLOG and Restarted the system now its not showing the future date,
Issue resolved.
Thanks ,
Jai -
How to show/print waiting message when system is serving pdf to browser
Hi,
does anybody know how to print/show "please wait for your request to be completed..." message when they try to click GeneratePdf button for example
they way i do serving pdf to the browser is as below
response.reset();
response.setContentLength(contentLength);
response.setContentType("application/pdf");
response.setHeader("Content-disposition", "inline; filename=\""System.currentTimeMillis()+".pdf"+ "\"");
output = new BufferedOutputStream(response.getOutputStream());
while (contentLength-- > 0) {
output.write(input.read());
output.flush();and this is what was written in my popup jsp ( when user click GeneratePdf , the application will process it and at the end serve pdf file to the user using popup window )
<body> <h1>Please Wait for your request to be completed...........</h1> </body> </html>
<%
boolean redirect=false;
try{
PdfDispatcher.dispatchApplication(response,session);
}catch(Throwable t){
System.out.println("Application Dispatcher Exception ... "+t.getMessage());
System.out.println("Continue as per normal....");
redirect = true; // will redirect to other jsp output
if(redirect){
//go to other jsp
}The problem is my message above never got printed to the page ( i guess because the browser thinks that the response has not been completed )
by the time the response has been completed the whole page will be cover in pdf document
The reason i want to do this because my user complaining that they see blank page for long time when the system is slow to generate/server pdf to them.
and it would be better to show some "waiting message" when the system is processing the application and server pdf at the end of the operations.
anybody know how to workaround this?
Thanksjust_a_kid83 wrote:
does anybody know how to print/show "please wait for your request to be completed..." message when they try to click GeneratePdf button for exampleUse JavaScript+DOM. Add a <div> somewhere in the page where the message should be displayed and put the message and an animated 'loading' gif in it. Hide the <div> using the CSS 'display' property which is set to 'none'. Then add an onclick event to the button/link which downloads the PDF file which gets the <div> element by its ID and set its 'display' property to 'block'. -
Hello Community
my ULS-logs are flooded with entries like
w3wp.exe SharePoint Foundation Topology ajczh High Unable to create the service call usage entry. Exception details: System.ObjectDisposedException: Message is closed. at System.ServiceModel.Channels.BufferedMessage.get_Headers() at Microsoft.SharePoint.Administration.SPServiceCallUsageEntry.Create(Message message) at Microsoft.SharePoint.SPServiceContextBehavior.System.ServiceModel.Dispatcher.IClientMessageInspector.BeforeSendRequest(Message& request, IClientChannel channel)
Searching for solutions did not succeed, as the EventID of ajczh is not found on the web. Anyone had this problem already?
Best Regards
MichaelHi Linda
thanks a lot for help.
I modified the ULS-logging to include verbose entries. The problem is correlated to Excel Services, which are functioning quite well on our side. Our Topology consists of an application server, 2 WFE and an office app server. We are using the BI features
of PowerPivot via an additional BI-SQL-server in SharePoint-mode.
Right before the strange entry in the logs we are getting these:
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Web Front End 145c Verbose ServerSession.ExecuteWithSecurityContext: Before issuing a new request to server http://XXXXX028:32843/[guid]/ExcelService*.asmx ServerRequestCount: 1, AllServersRequestCount: 2, workerThreads: 395, completionPortThreads: 400
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Web Front End 8k3v Verbose ServerInfo.AcquireHealthCheckPriviliges: Acquired HealthCheck priviliges for server 'http://XXXXX028:32843/[guid]/ExcelService*.asmx'
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Excel Calculation Services d51n Medium MossHost.GetEndpointAddress: Server endpoint Uri: http://XXXXX028:32843/[guid]/ExcelService.asmx.
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Excel Calculation Services d51b Verbose MossHost.CreateServiceChannel<IExcelServiceSoap>: About to create service channel in Claims mode.
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Excel Calculation Services d51c Verbose MossHost.CreateServiceChannel<IExcelServiceSoap>: Service channel created.
02.26.2014 10:42:45.02 w3wp.exe Excel Services Application Web Front End abpw Verbose ServerSession.GetHealthScoreCallback: About to send a GetHealthScore call to server http://XXXXX028:32843/[guid]/ExcelService*.asmx
02.26.2014 10:42:45.02 w3wp.exe SharePoint Foundation Topology e5mc Medium WcfSendRequest: RemoteAddress: 'http://XXXXX028:32843/[guid]/ExcelService.asmx' Channel: 'Microsoft.Office.Excel.Server.CalculationServer.Proxy.IExcelServiceSoap' Action: 'http://schemas.microsoft.com/office/Excel/Server/WebServices/ExcelServerInternalService/ExcelServiceSoap/GetHealthScore' MessageId: 'urn:uuid:61212e7d-cf02-41ad-9876-2adf17ec2807'
02.26.2014 10:42:45.02 w3wp.exe SharePoint Foundation Topology ajczh High Unable to create the service call usage entry. Exception details: System.ObjectDisposedException: Message is closed. at System.ServiceModel.Channels.BufferedMessage.get_Headers() at Microsoft.SharePoint.Administration.SPServiceCallUsageEntry.Create(Message message) at Microsoft.SharePoint.SPServiceContextBehavior.System.ServiceModel.Dispatcher.IClientMessageInspector.BeforeSendRequest(Message& request, IClientChannel channel)
that's it, unfortunately. These entries are repeating every 15 seconds.
Best Regards
Michael -
i can't update my itunes and it shows me this message: The installer has insufficient privileges to access this directory: C:/program files/itunes. The installation cannot continue. Log on as administrator or contact your system administrator
Hello PamelaFox14,
Thank you for using Apple Support Communities.
It sounds like you need to log in as the administrator to update the iTunes application properly.
Take a look at this article named:
Trouble installing iTunes or QuickTime for Windows
http://support.apple.com/kb/HT1926
This section in particular:
1. Make sure you have administrator account access
To install iTunes or QuickTime software, you need to be logged in as an administrator on the computer. If you're not sure if you have administrator account access, you may find this Microsoft article helpful:
Windows 7: How do I log on as an administrator?
Otherwise, refer to the Help documentation from Microsoft, contact your IT department, or visitsupport.microsoft.com for more information.
All the best,
Sterling -
Data Manager Default System Messages
Hi, I need to change the data managers default system messages e.g
When adding a duplicate value into a unique field you get; "Unique Constrains Violated" it should read something like "Duplicate value, try again"
Please advice.
ThanksHi Chris,
As rightly mentioned by Jitesh, this is not supported by MDM.
You can only set custom messages to the Validations that you create in Data manager yourself which will be displayed if those validations are voilated.
Thanks and Regards
Nitin jain -
HT204135 How can one make the printer dialog box to have Show Details as default?
I very often use different presets from document to document. Thanks.
Once you select the Show Details for any application, the next time you use that application and select to print, the full details pane should be shown.
If this is not happening and the applications always show the Hidden Details print dialog then you may need to perform some sort of reset.
Also, if you were to use the Presets option and set commonly used settings as a Preset, then even if the print dialog is not showing the extra details, you can still select the desired Preset from this print dialog. -
Server Error in '/' Application.
Unable to ExecuteModuleActionURI : Module/Jobs/Controller/Applications/Action/Apply/JobID/915337
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Exception: Unable to ExecuteModuleActionURI : Module/Jobs/Controller/Applications/Action/Apply/JobID/915337
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[Exception: Unable to ExecuteModuleActionURI : Module/Jobs/Controller/Applications/Action/Apply/JobID/915337]
BiteCMF.Util.Xsl.ExtensionObjects.BiteExtensionObject.ExecuteModuleActionURI(String moduleActionURI, String location) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Util\XSL\ExtensionObjects\BiteExtensionObject.cs:63
[XslTransformException: An error occurred during a call to extension function 'ExecuteModuleActionURI'. See InnerException for a complete description of the error.]
System.Xml.Xsl.Runtime.XmlExtensionFunction.Invoke(Object extObj, Object[] args) +1292307
System.Xml.Xsl.Runtime.XmlQueryContext.InvokeXsltLateBoundFunction(String name, String namespaceUri, IList`1[] args) +806
<xsl:template match="Job">(XmlQueryRuntime {urn:schemas-microsoft-com:xslt-debug}runtime, XPathNavigator {urn:schemas-microsoft-com:xslt-debug}current, String URL) +20724
<xsl:template match="ViewData">(XmlQueryRuntime {urn:schemas-microsoft-com:xslt-debug}runtime, XPathNavigator {urn:schemas-microsoft-com:xslt-debug}current) +152
<xsl:apply-templates>(XmlQueryRuntime {urn:schemas-microsoft-com:xslt-debug}runtime, XPathNavigator ) +806
Root(XmlQueryRuntime {urn:schemas-microsoft-com:xslt-debug}runtime) +55
System.Xml.Xsl.XmlILCommand.Execute(Object defaultDocument, XmlResolver dataSources, XsltArgumentList argumentList, XmlWriter writer, Boolean closeWriter) +150
System.Xml.Xsl.XmlILCommand.Execute(IXPathNavigable contextDocument, XmlResolver dataSources, XsltArgumentList argumentList, XmlWriter results) +88
System.Xml.Xsl.XslCompiledTransform.Transform(IXPathNavigable input, XsltArgumentList arguments, Stream results) +89
BiteCMF.Util.Xsl.BiteXsl.Transform(XmlDocument xmlToTransform) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Util\XSL\BiteXSL.cs:216
BiteCMF.Util.Xsl.BiteXsl.Transform(XmlDocument xmlToTransform, String xslUrl) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Util\XSL\BiteXSL.cs:182
BiteCMF.Modules.ViewActionResult.ToString(BiteRequestBroker requestBroker) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Modules\ViewActionResult.cs:166
BiteCMF.Modules.ViewActionResult.Process(BiteRequestBroker requestBroker) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Modules\ViewActionResult.cs:255
BiteCMF.Modules.CMS.CMSRequestBroker.ProcessRequestAsFrontend() in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Modules\CMS\CMSRequestBroker.cs:221
BiteCMF.Modules.CMS.CMSRequestBroker.HandleRequest() in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\Modules\CMS\CMSRequestBroker.cs:45
BiteCMF.CMS.BiteRequestBroker.ExecuteModuleBrokers() in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\CMS\BiteRequestBroker.cs:165
BiteCMF.CMS.BiteRequestBroker.ProcessRequest() in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\CMS\BiteRequestBroker.cs:83
BiteCMF.BiteHttpModule.ProcessRequest(HttpApplication app) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\BiteHttpModule.cs:192
BiteCMF.BiteHttpModule.Application_PostAcquireRequestState(Object source, EventArgs e) in C:\Users\mbailey.REDANT\Desktop\Projects\Changeboard\BiteCMF\BiteHttpModule.cs:164
System.Web.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +80
System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +171
Version Information: Microsoft .NET Framework Version:2.0.50727.5448; ASP.NET Version:2.0.50727.5456http://ww2.cs.fsu.edu/~rosentha/linux/2.6.26.5/docs/DocBook/libata/ch07.html#excatATAbusErr wrote:
ATA bus error means that data corruption occurred during transmission over ATA bus (SATA or PATA). This type of errors can be indicated by
ICRC or ABRT error as described in the section called “ATA/ATAPI device error (non-NCQ / non-CHECK CONDITION)”.
Controller-specific error completion with error information indicating transmission error.
On some controllers, command timeout. In this case, there may be a mechanism to determine that the timeout is due to transmission error.
Unknown/random errors, timeouts and all sorts of weirdities.
As described above, transmission errors can cause wide variety of symptoms ranging from device ICRC error to random device lockup, and, for many cases, there is no way to tell if an error condition is due to transmission error or not; therefore, it's necessary to employ some kind of heuristic when dealing with errors and timeouts. For example, encountering repetitive ABRT errors for known supported command is likely to indicate ATA bus error.
Once it's determined that ATA bus errors have possibly occurred, lowering ATA bus transmission speed is one of actions which may alleviate the problem.
I'd also add; make sure you have good backups when ATA errors are frequent -
Dear all,
Any one can please tell me the unique id for System Message. Also i want to know the unique id for 'yes' and 'No' in System Message. Its very urgent
Thanks in advance
with Regards
G.shankarSystem message has formtype = 0. The Yes and No button has no ids for sap, but when you want to press one of this button, use sendkeys as SBO_Application.SendKeys("") or tab for No (default is Yes).
For accesing to correct system message, use some global variable and there before showing system msgbox set some value and compare it after showing.
hope it helps -
How can I clean up queue one-time on Sun Java system messaging 6.3
Hi,
<address>Our Email server have a problem, When I run _./imsimta qm directory tcp_local_, There are about 5 Millions of messages in the queue.</address>
Now our Email server send messages very slowly, how can I clean up queue one-time?
the command _./imsimta qclean_ is very slowly.
What can I do to prevent this problem?
our Email server version is :
Sun Java(tm) System Messaging Server 6.3-6.03 (built Mar 14 2008; 32bit)
libimta.so 6.3-6.03 (built 17:12:37, Mar 14 2008; 32bit)
SunOS email-1 5.10 Generic_120011-14 sun4u sparc SUNW,Sun-Fire-V890
Thank you !If you have more than 100,000 messages in the queue, then look at the MAX_MESSAGES parameter in [the job_controller.cnf file|http://wikis.sun.com/display/CommSuite/Job+Controller+Configuration+File]. If the parameter is not specified, it defaults to 100000. If you have more than that number of messages in the channel queues, it will take a long time for new/legitimate messages to be sent because job_controller is only considering the first 100,000 messages in the queue.
If you get into the "imsimta qm" command do do "sum -database", it will show a summary of what job_controller has in its internal cache and therefore what job_controller is working on. If you compare that to "sum -directory" you will probably see a difference.
If these are all legitimate messages, you need to increase MAX_MESSAGES, cnbuild, and restart job_controller.
If they are not, then preventing this in the future will require determining how they got into your queue and correcting that.
As for removing them, the "imsimta qm" commands allow you to select messages by various criteria and then you can "return" or "delete" them. But yes, that will take a long time if there are many messages because it is a single threaded process and it needs to open and examine each message. You may be able to accomplish the task more quickly with a shell script that works on individual channel queue subdirectories and then run multiple copies of that script in parallel. After you have cleaned out the queue, restart job_controller.
Also, you might want to consider [the subdirs channel keyword|http://msg.wikidoc.info/index.php/Subdirs_and_nosubdirs_Channel_Options]. -
My Photo Not Showing Up in Messages
My photo does not show beside my texts in Messages on my Mac. Only a shadow of a generic person in a rectangle is there. I can see the photos of others who write me, though. I have my photo in Contacts and it does show up in Mail, but not in Messages. My photo also shows up in IMessage on the iPad.
Why is my photo not showing up in Messages and how could I make it visible? Thanks.HI,
Your Pic is set if you have Buddy list set up/logged in.
Enable the Bonjour account if you do not have Jabber, AIM or Yahoo IDs set up in Messages.
Click on the current Buddy Pic.
You may find it has pulled the Pic from the My Card in the Contacts app (Formerly the Address Book)
In turn this may be picking up on the System Preferences > User and Groups > your account Login pic.
That is to say when you set up the (Mac User) Account it asked you to create/chose a pic from the Login Screen.
Later the process of setting up an Accounts asked for details that create the Contacts/Address Book Card and the Login in pic is dragged across.
AS you then get to set up Messages (Or iChat) then the My Card pic is pulled through.
All three spots can be changed independently of each other.
Some of the Recent Items can be from either of the others.
This is my Buddy list pic and th "Recents" I have.
The Zebra and head in "teeth" pics are from some testing I did with Pics in the Contacts > My Card options rather than Messages.
Finally once you have a pic linked to Messages then it also show up at your end for the Chat window for iMessages (as well as for you in AIM or Jabber)
NOTE
In AIM and Jabber (Or Yahoo) your Pic is Broadcast and is what you Buddy sees next to your Name (They can override this though)
In iMessages though your pic is not sent and your Buddy's Contacts app supplies whatever pic they have for you. (As yours does for them)
9:10 PM Saturday; December 8, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images." No, Seriously
Maybe you are looking for
-
File Error: Unknown File, Cannot Save
I hope this is only a matter of healthy file management, but I'm quite confused and hope someone can clear this up into something of a simple science. On the otherhand, could this be a LIMITATION of FCP? -Have been editing a sequence from a larger fi
-
How to modify a column name & How to modify a constraint name
How to modify a column name? How to modify a primary key constraint name if the pk has been referenced by another foreign key? Thanks.
-
Ipod won't sync with windows 8
The Ipod connects and shows up in iTunes (yes latest version) but I can't sync - it's grayed out. For some reason all the songs on the Ipod are not also present on the computer. The original computer the iPod was set up on was a Vista machine. It die
-
I bought iPhone 3GS(Used) recently and updated ios 6.1.3 my iPhone is taking blurry Pictures through basic default Cam app.Can anybody please let me know any solution for this?
-
Dear All, Please guide me is it possible that order unit of measure is To but confirmation unit of measure is PC. is yes then how