Show IP connected to Port ??

hi guyz, is ther a command in cisco to show the ip address connected to a particular port ???
For example, PC A 10.1.1.1 connected to FE0/1.
Command to show 10.1.1.1 connected to Fe0/1....

I dont think there is any direct command that will give you the ip address connected to a particular port
If the Ip address are in the same broadcast domain, u can use arp and the Mac address mapping to get the port it is connected to
eg..
ms_mla_mgmt_14dc#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.16.102.246 7 0002.e355.0b6e ARPA VLAN1
Internet 172.16.102.88 0 0009.6bb7.d330 ARPA VLAN1
ms_mla_mgmt_14dc#sh mac-address-table address 0002.e355.0b6e
Non-static Address Table:
Destination Address Address Type VLAN Destination Port
0002.e355.0b6e Dynamic 1 FastEthernet0/21
ms_mla_mgmt_14dc#
ms_mla_mgmt_14dc#

Similar Messages

Wifi problem: I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and n

I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and never happened before I have tried resetting the airport unit but still no luck please help.
Thank you
Roy from malden

Hi Roy, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

UCCX 10.5 Real Time Report shows "Not Connected"

Hi,
UCCX 10.5 HA over LAN.
As per the title, RTR shows Not connected for both nodes and no data shown for all reports. all services are In service in both nodes.
Any Ideas?
Regards.

Hi Mohamed,
Are you accessing this via the IE or FF? If so which version?
The Real time reporting on UCCX connects to the RMI port 6999 to pull the information on the Engine. If there are no port blockages or if there are no issues with the browsers, then it is a problem with the configuration files in root holding this information which needs in depth analysis.
A restart of the Engine also should help. I know that everything is IN SERVICE, but I have noticed a lot of issues on UCCX 10.5 when there are stuck calls on the system, it impacts RTR with the midnight stats reset.
The reset of the Engine is bound to clear all the stuck calls in the system and this may be a side effect of the stuck calls on the system especially if the RTR was working before you noticed the problems.
Regards,
Arundeep

My ipad is showing the connect to itunes and will not move from there.

After trying to update my ipad. I recieved an "unable to update" error message. Now all my ipad will do is show the connect to itunes symbols. I cannot get is to restart or restore. itunes is not recognizing the ipad.

You will probably need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Or you can follow these Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.

Error Message "The Remote device or resourse wont accept connection, not set up to accept connection from port https"

I get this error message when trying to open and log into an online casino "The Remote device or resource wont accept connection, not set up to accept connection from port https".
I am on a desktop computer my connection to the net is with a USB Virgin Mobile hotspot device.
I also have issues with some downloads not installing right for instance SKYPE wont work. If the problems are related I don't know
Thanks

Starting in Firefox 14, Firefox will guess an address and place it in the address bar (AutoFill feature). If you have ever connected to the site using a secure (HTTPS) connection, then Firefox will try to connect security to the address suggested by the AutoFill feature. To work around this you can:
* Edit the address to force Firefox to interpret your entry literally. For example, if there is a trailing / you can remove it.
* Turn off the URL bar AutoFill feature and just use the AutoSuggest drop-down.
* Clear Firefox's memory of the site so it doesn't default to a secure connection (however, this also removes any bookmarks you have to pages on the site).
To disable the in-address-bar autofill without losing the suggestions that appear below the bar:
(1) In a new tab, type or paste '''about:config''' in the address bar and press Enter. Click the button promising to be careful.
(2) In the filter box, type or paste '''autofill''' and pause while the list is filtered
(3) Double-click '''browser.urlbar.autoFill''' to toggle it from true to false. You're done with about:config and you can close this tab.
"Forget about this site" will clear cache, history, bookmarks, and permissions for the site, and probably any saved certificate. There are two ways to get to this:
* History > Show All History, right-click an entry for the site > "Forget about this site"
* Type or paste about:permissions in the address bar and press Enter, then select the site from the list on the left side, and click the "Forget about this site" button on the right side
Depending on the size of your history and cache, this may lock Firefox up for a minute or two while everything is cleansed.

I have a mac os x snow leopard. my problem is that when i go to the ethernet settings it shows 'not connected'. i called the internet person even he couldn't fix it PLEASE HELP!!!!!!!!!!!!!!

i have a mac os x snow leopard. my problem is that when i go to the ethernet settings it shows 'not connected'. i called the internet person even he couldn't fix it PLEASE HELP!!!!!!!!!!!!!!

System Preferences > Network > Ethernet? If that shows "not connected" that is all your Mac knows. As far as it is concerned there is no cable connected to the port on your Mac, or the other end of the cable is either disconnected or connected to something that is broken.
Try another cable. If the cable is broken you will also get that status message. If you have exhausted all of these possibilities, the only remaining cause is an inoperative port on your Mac.

Roland UM-ONE CD-ROM does not mount on iMac OS 10.8.2 Roland driver for 10.8 installed as directed. No power ready light shows when connecting UM-ONE. System Profiler shows it, but not configured. Older UM-1X works fine. UM-ONE works on Dell Windows XP.

UM-ONE
Roland supplied CD-ROM does not mount or read by iMac OS 10.8.2, works with old TiBook and Dell laptop, however.
Got latest driver from RolandUS.com (um_1mx8d_v100), installed as directed.
No power ready light shows when connecting UM-ONE.
System Profile shows it there, but not configured.
With Audio MIDI Setup opened to MIDI Studio window, UM-ONE does not appear.
Tried many things without success. Tried swapping UM-1X (formerly on Dell laptop) with UM-ONE. UM-ONE installed and worked there without any issues. MIDI instrument communicates fine.
The UM-1X works without complaint and as expected when connected to any USB port on either the Dell or iMac, even a hub or keyboard port, just as it formerly had before changing operating systems, etc. It is old, but reliable.
Upshot is, for now, that UM-1X works with either the Dell or the iMac, but is currently attached to the iMac. UM-ONE (2011 model) only works with the Dell (Windows XP).

Same problem here! The only difference is that I'm using a MacBook pro 13 inch (2011)

Listener shows blocked connections

Hi,
I am working on 6.1 AIX with Oracle 11g R2 (11.2.0.2.0). I am trying to connect from one database server to another. I have moved the password file and renamed it as well. But when I try to connect from source server to target server it gives 'Connected to ideal instance'
Checking on the target database server, the listener is showing blocked connections
LSNRCTL for IBM/AIX RISC System/6000: Version 11.2.0.2.0 - Production on 07-FEB-2012 08:31:06+
++Copyright (c) 1991, 2010, Oracle. All rights reserved.++
++Welcome to LSNRCTL, type "help" for information.++
++LSNRCTL> status++
++Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=drctest.testtst.com)(PORT=1521)))++
++STATUS of the LISTENER++
++------------------------++
++Alias LISTENER++
++Version TNSLSNR for IBM/AIX RISC System/6000: Version 11.2.0.2.0 - Production++
++Start Date 07-FEB-2012 08:25:21++
++Uptime 0 days 0 hr. 5 min. 47 sec++
++Trace Level off++
++Security ON: Local OS Authentication++
++SNMP ON++
++Listener Parameter File /u01/app/oracle/product/11.2.0.2.0/dbhome_1/network/admin/listener.ora++
++Listener Log File /u01/app/oracle/diag/tnslsnr/TESTTST/listener/alert/log.xml++
++Listening Endpoints Summary...++
++(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=DRCTEST.testtst.com)(PORT=1521)))++
++(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))++
++Services Summary...++
++Service "drctest" has 1 instance(s).++
++Instance "drctest", status BLOCKED, has 1 handler(s) for this service...++
++Service "drctest.testtst.com" has 1 instance(s).++
++Instance "drctest", status UNKNOWN, has 1 handler(s) for this service...++
++The command completed successfully++
Please any possible suggestions and hints. Thank you very much.

Check status of instance: if instance is in mounted status, listener will block database connections because only users having SYSDBA privilege can login.
SQL> select status from v$instance;
STATUS
MOUNTEDgoes with:
C:>lsnrctl status
LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 07-F╔VR.-2012 19:43:59
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias                     LISTENER
Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Production
Start Date                07-F╔VR.-2012 18:45:48
Uptime                    0 days 0 hr. 58 min. 11 sec
Trace Level               off
Security                  ON: Local OS Authentication
SNMP                      OFF
Listener Log File         C:\oraclexe\app\oracle\diag\tnslsnr\Acer\listener\alert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=Acer)(PORT=1521)))
Services Summary...
Service "xe" has 1 instance(s).
Instance "xe", status BLOCKED, has 1 handler(s) for this service...
The command completed successfullyIf you run:
SQL> alter database open;
Database altered.
SQL>Then you will get:
C:>lsnrctl status
LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 07-F╔VR.-2012 19:44:28
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias                     LISTENER
Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Production
Start Date                07-F╔VR.-2012 18:45:48
Uptime                    0 days 0 hr. 58 min. 40 sec
Trace Level               off
Security                  ON: Local OS Authentication
SNMP                      OFF
Listener Log File         C:\oraclexe\app\oracle\diag\tnslsnr\Acer\listener\alert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=Acer)(PORT=1521)))
Services Summary...
Service "xe" has 1 instance(s).
Instance "xe", status READY, has 1 handler(s) for this service...
The command completed successfullyEdited by: P. Forstmann on 7 févr. 2012 19:56

Whenever I update from Windows 7 get error 1602, iPod shows USB connection to iTunes, but iTunes will not recognize the device. None of the Apple documentation helps.

Whenever I update from Windows 7 get error 1602, iPod shows USB connection to iTunes, but iTunes will not recognize the device. None of the Apple documentation helps. The Apple Mobile Device driver is loaded and operating. The anti-virus software and firewall are not at fault (were uninstalled, and made no difference). The iTunes on my older machine running Vista does recognize the inoperative iPod (iTunes has detetced an iPod in recovery mode) and allows me to restore the device. Can anyone help to resolve this problem on the Windows 7 PC?

So yu tried all of this:
Error 1600, 1601, 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
If you had then time for an appointment at ther Genius Bar of an Apple store.

Interpreting show tfo connection summary output

In the output from the 'show tfo connection summary output' command there are 3 sections :
- Optimized Connection List
- Auto-Discovery Connection List
- Pass-Through Connections
The 'Pass-Through Connections' section is fairly self-evident, but what is the difference between entries in the 'Auto-Discovery Connection List' and the 'Optimized Connection List' sections ?
Also, I have some output that I am having difficulty interpreting :
Auto-Discovery Connection List
E: Established, S: Syn, A: Ack, F: Fin, R: Reset
s: sent, r: received, O: Options, P: Passthrough
Local-IP:Port Remote-IP:Port Conn-Type Orig-St Term-St
10.250.216.5:4050 10.250.195.3:27903 Int. Server SAsO UNU
10.250.195.7:443 10.250.216.5:27655 Ext. Server SAsO SAr
What are do the 'Int. Server' and 'Ext. Server' types mean under the column 'Conn-Type' ?
What are 'Orig-st' and 'Term-st'abbreviations for ? Original state/terminated state ??
Finally, what does the UNU under the Term-st column mean ?
Apologies for the many questions, but I can't find any answers in the Cisco config or command ref guides...
Thanks
Nigel.
Thanks
Nigel.

Nigel,
The optimized connection list shows connections that are established and being optimized. The auto-discovery connection list shows connections that are still in the auto-discovery phase (i.e. the 3-way setup handshake has not completed).
The designation 'Int. Server' or 'Ext. Server' indicates whether the connection is sourced/destined from/to an internal process (such as WAFS, telnet, etc.) or an external host.
'Orig-st' and 'Term-st' are as you described them.
UNU = unknown.
Zach

Help: Mail server refuses connection to port 143

Hi,
i am having this problem with accessing mail from my mac. It is a recurring problem everytime when i use Mail to access my .mac account.
This is what in shows- "There may be a problem with the mail server or network. Check the settings for account "[email protected]" or try again.
The server error encountered was: The server "mail.mac.com" refused to allow a connection on port 143."
I m very puzzled by this, it is a problem that happens on an 'on-off' basis, so sometimes it is ok and sometime it cannot access the server.
Please advice on this issue.
P.S i can access mail via Safari online.
cheers
2Ghz Macbook 'White' Mac OS X (10.4.6)

I'm not having the same problem.
It occurs every time you use the Mail.app to access your .Mac account and if so, how long have you had the account?
The default incoming mail server port for IMAP type accounts is 143 and since a .Mac type account is really an IMAP type account, are you accessing any other IMAP type accounts with the Mail.app?
How are you connected to the internet - via an Ethernet connection to a Cable or DSL modem or thru a wired or wireless router connected to same?

What is (en1) adapter and why am I not showing airport connection?

Ok, so I'm in the network preference pane looking at three possibilities.
1) Ethernet adapter (en1) which shows an IP and tells me I'm connected to the internet.
2) Airport which is connected to my home network but does not have an IP and "cannot connect to the Internet"
3) VPN (L2TP) which is configured but not connected.
So, back to my original question. As I am obviously connected to the Linksys wireless router through the airport card, what is this en1 and why does it tell me I'm connected through it instead of the airport?
Message was edited by: Trent Mckenica
Message was edited by: Trent Mckenica

I was (am) definitely connected. Just was a little confused as to why the Airport pane didn't show connectivity. I ended up going to sysprefs, choosing "Show: Network Port Configurations", and dragging the Airport to the top of the list. (It did show BOTH Airport and en0 network adapter as choices). After dragging Airport to the top of the list, the Airport TCP/IP pane showed the connectivity I expected to see in the first place. Really not an issue as I was always connected anyways, just not what I was used to seeing.

I've factory rested my phone and now its showing to connect to itunes after connecting it is downloading software

i've factory rested my phone and now its showing to connect to itunes after connecting it is downloading software

No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

I just downloaded the new version of Firefox and now every site I used to use such as Facebook, Twitter, and Youtube show "This Connection Is Untrusted"

I just downloaded the new version of Firefox and now every site I used to use such as Facebook, Twitter, and Youtube show "This Connection Is Untrusted". Even when I do accept the risks the site no longer looks the way it's looked for years. Twitter doesn't even give me the option to accept the risks at all and shows this error (Error code: sec_error_unknown_issuer). I've tried resetting Firefox, I've checked the time and date, and I've removed and added Firefox to see if that would work. Nothing seems to be working so I can see the sites the way they normally would be instead of "coded". Can anybody help me please?!!! Thanks

ok, unfortunately the fiddler2.com issuer in certificates might be a sign of unwanted software present on your pc that is intercepting secure network traffic. please go into the system control panel and uninstall programs like BrowserSafeguard, BrowserSafe, SafeGuard or other software that sounds suspicious and didn't get installed by you intentionally.
<sub>reference: https://support.mozilla.org/en-US/questions/982532#answer-520145</sub>
afterwards, run a full scan of your system with different security tools like the [http://www.malwarebytes.org/products/malwarebytes_free free version of malwarebytes] & [http://www.bleepingcomputer.com/download/adwcleaner/ adwcleaner].
[[Troubleshoot Firefox issues caused by malware]]

Database account locked as it tries to connect different ports for 16 times

I need a help in answering one of the issue encountered last week.
I have created a database link and tried to access the information from a table using the program written in another language. The password provided was incorrect for that user while creating database link. So we expected that,while retrieving the data, Database connection has to be errored out as password provided is incorrrect.
But unfortunately, user account was locked out. When i checked with DBAs they mentioned that it tries to connect 16 ports with in a min of time.we were shocked as it STOPS another scheduled jobs with that user. and affects production badly.
As per the program, it has to connect only one time and yesterday we tried to execute the program in DBAs observation and it errored out as expected. Didn't tried for multiple ports.
Now the question is, WHY the database connection established 16 times last week and caused user account locked. DBAs are unable to answer it. Any EXPERTs opinion on this would greatly appreciated.
I have verified managing ports in oracle documentation, it was mentioned that if one port is busy it will try to connect to another port in the range of ports mentioned during the installtion. DBAs verified ports related file and it was blank. and they are not agreeing with this reason. Please HELP me in finding the correct REASON for this.
is it a NETWORK issue or issue with DATABASE SERVER only?
Thanks
SSP
Edited by: 960738 on Sep 22, 2012 9:13 PM

960738 wrote:
I need a help in answering one of the issue encountered last week.
I have created a database link and tried to access the information from a table using the program written in another language. The password provided was incorrect for that user while creating database link. So we expected that,while retrieving the data, Database connection has to be errored out as password provided is incorrrect.
But unfortunately, user account was locked out. When i checked with DBAs they mentioned that it tries to connect 16 ports with in a min of time.we were shocked as it STOPS another scheduled jobs with that user. and affects production badly.
As per the program, it has to connect only one time and yesterday we tried to execute the program in DBAs observation and it errored out as expected. Didn't tried for multiple ports.
Now the question is, WHY the database connection established 16 times last week and caused user account locked. DBAs are unable to answer it. Any EXPERTs opinion on this would greatly appreciated.
I have verified managing ports in oracle documentation, it was mentioned that if one port is busy it will try to connect to another port in the range of ports mentioned during the installtion. DBAs verified ports related file and it was blank. and they are not agreeing with this reason. Please HELP me in finding the correct REASON for this.
is it a NETWORK issue or issue with DATABASE SERVER only?
Thanks
SSP
Edited by: 960738 on Sep 22, 2012 9:13 PMDBLINK is 100% oblivious to the fact any port exists.
DBLINK only contains username, password & TNS Alias.
can you post actual SQL & results?

Show IP connected to Port ??

Similar Messages

Maybe you are looking for