Show isdn status shows deactived

Briefly, I have 2 out 6 remote sites with bri cards that continue to show deactived on the layer 1 status. Telco says the lines are good. I have tried every switch type, reconfiguring, everything I can think of.
any suggestions?

hi
I guess these links will be of some help to you.
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b76.shtml
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b77.shtml
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080093c1a.shtml
would also suggest to physically check the voltage on the bri link which will also help you to isolate the exact cause for the deactivation.ideally it should be in the range of around 95V-105V..
regds

Similar Messages

Router still show ISDN up on "sh isdn ac" command even when ISDN down.

Hi experts,
I encounter a situation where my router still showing the isdn is up (in "sh isdn ac" command) even when the ISDN is down (I shut it down). Is it an IOS bug?
My router is Cisco 3640 with IOS Version 12.3(21). The IOS are currently upgrade from Version 12.2(6a).
The ISDN is a backup for leased line to MPLS. It will first call to MPLS nearest node LAC router, and if that failed, it will call to HQ as a last result.
Thanks.
Azmir.

This has to be a bug. Please check the bug navigator. Also, the show isdn status is showing the clear picture. The layer 3 status is showing as 0 active calls. That means it is not able to clear the isdn call history data.
--Pls rate if useful--

Isdn Layer 1 deactivated when there is no active call

Hi All,
I am in Nairobi Kenya. Here we use ISDN Basic-net3 and my problem is that most of the telco switches here deactivate Layer 1 when there is no active call.
When I try to initiate a call by using the ISDN test call command I get an error to the effect that B channel is not available.
The only way I can initiate a call is I first call the line then and then disconnect. Then I have about 5 seconds to make a test call and pings are successful. How do I make the router initiate a call when layer 1 is deactivated.
the debug isdn q921 out has nothing till a call comes in.
I also understatnd that European ISDN switches deactivate Layer 1 when there no active call. I dont have a problem with one of the switches, coz it does not bring down the line when there is no active call.
Thakx in advance
Martin

Thanks for the quick response.
It is a cisco 1760
The IOS is c1700-sv3y-mz.122-15.T5.bin
When I try to make a test call the show isdn status initially indicates that the router is trying to activate layer 1 then after 5 seconds it indicates that it is deactivated.
I have not yet configured DDR as indicated in the config file
Building configuration...
Current configuration : 3054 bytes
! Last configuration change at 00:38:54 UTC Mon Aug 9 1993
! NVRAM config last updated at 00:36:54 UTC Mon Aug 9 1993
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Gill-House
logging queue-limit 100
enable secret xxx
ip subnet-zero
no ip domain lookup
isdn switch-type basic-net3
no voice hpi capture buffer
no voice hpi capture destination
class-map match-all voice-traffic
match ip rtp 16384 16383
policy-map voice
class voice-traffic
priority 24
class class-default
fair-queue
gw-accounting syslog
interface Loopback0
description Loopback interface for VoIP Dial-peers
ip address 128.1.x.x.255.255.255
interface Multilink1
bandwidth 6
ip address 128.1.x.x.255.255.252
ip tcp header-compression iphc-format
ppp multilink
ppp multilink fragment-delay 20
ppp multilink interleave
multilink-group 1
ip rtp header-compression iphc-format
interface FastEthernet0/0
description Gill-House LAN
ip address 128.1.x.x.255.255.0
speed auto
interface Serial0/0
description Link to Head Office
bandwidth 64
no ip address
encapsulation ppp
no fair-queue
ppp multilink
multilink-group 1
interface BRI1/0
ip address 10.10.1.2 255.255.255.0
encapsulation ppp
isdn switch-type basic-net3
isdn point-to-point-setup
keepalive 20
router eigrp 100
passive-interface FastEthernet0/0
passive-interface Loopback0
network 128.1.0.0
no auto-summary
no eigrp log-neighbor-changes
ip classless
no ip http server
logging source-interface Loopback0
logging 128.1.1.179
call rsvp-sync
voice-port 2/0
cptone GB
ring frequency 50
voice-port 2/1
cptone GB
ring frequency 50
dial-peer cor custom
dial-peer voice 2 pots
destination-pattern 101
port 2/0
dial-peer voice 51 voip
destination-pattern 100
session target ipv4:128.1.0.254
ip qos dscp cs5 signaling
dial-peer voice 55 voip
destination-pattern 120
session target ipv4:128.1.31.254
ip qos dscp cs5 signaling
dial-peer voice 52 voip
destination-pattern 102
session target ipv4:128.1.91.254
ip qos dscp cs5 signaling
dial-peer voice 53 voip
destination-pattern 103
session target ipv4:128.1.121.254
ip qos dscp cs5 signaling
dial-peer voice 54 voip
destination-pattern 110
session target ipv4:128.1.21.254
ip qos dscp cs5 signaling
dial-peer voice 56 voip
destination-pattern 130
session target ipv4:128.1.41.254
ip qos dscp cs5 signaling
dial-peer voice 57 voip
destination-pattern 140
session target ipv4:128.1.111.254
ip qos dscp cs5 signaling
dial-peer voice 58 voip
destination-pattern 150
session target ipv4:128.1.61.254
ip qos dscp cs5 signaling
dial-peer voice 59 voip
destination-pattern 160
session target ipv4:128.1.71.254
ip qos dscp cs5 signaling
line con 0
logging synchronous
line aux 0
line vty 0 4
password housing
login
ntp clock-period 17208074
ntp server 128.1.1.211
ntp server 128.1.0.254
end
Gill-House#

Purchase Order has approved but Status show as Unapproved

Dear All Experts,
I have a Purchase Order need to go throught approval procedure. The Purchase Order has approved by user and add into system and printed out. When second time, open the same Purchase Order, the status show "Unapproved" but the Purchase Order windows header name show Purchase Order [Approved], this make user unable to copy to GRPO. I have try to restore stored procedures in SAP B1, it does not make any changes. The user is using SAP B1 2007A SP0 PL49. Please Advise.

Hi Angie
the purchase order once approved has to be added on to the system after approval if u say that u have added the purchase order after it got approved then that seems to be a concern for that u need to contact ur sap partner or if u are a partner then u need to get in touch with sap to resolve the isssue as it could be because of problem with ur database
but before that please be sure off that u are using the correct way and have sucessfully added the documnt apon approval.
Regards,
Manish

Sale order status showing being processed

Dear Friends,
I am working in SAP ECC 6.0
My sale order Qty is 10 pcs eing processed
and delivery qty is 10 pcs - Completed
Good Issue - 10 Pcs - Completed
Invoice - 10 Pcs - Completed
In spite of carrying out full delivery sale order status is still showing being processed.
is there any configuration missing or is there any program to update the status.
Kindly advice.
Satish

Hi Ankur,
2 Doubts i have:
1)
In our case for the Item Category we have not maintained anything in Completion Rule however we have maintained Update Document Flow in Order to Delivery Copy Control.
Our Document status shows as Completed in this case as well. Hence i do not know the Significance of maintaining Completion rule in item category.
2) I have a order type which has Order Relevant Billing. The Copy Control for Order to Billing does not have any Update Document Flow Check Box. We are using a Service Material in this Order Type.
After creating the Billing we still have Order status as Being Processed.
Can you help in finding a solution to the above?
Madhukar

Delivery Document has been created - showing the status of Being Processed.

Hi All.
I am facing the following typical problem.
1. Sales order has been created - showing the status of COMPLETED.
2. Delivery Document has been created - showing the status of Being Processed.
3. Goods Issue document created successfully- showing status as COMPLETE
4. Billing Document has created successfully - showing the status as COMPLETED.
5. Customer Account got updated properly.
Query: Despite of completion of SO, DELIVERY, GOODS ISSUED, AND BILLING DOCUMENT u2013 and accounting document is cleared why the outbound Delivery document status is showing as BEING PROCESSED.
If I go T-code Vlo3n see document flow
Delivery 5080789885 being processed.
Go to VF03 document flow also it is showing
Delivery 5080789885 being processed.
Aditya

Hi ALL,
Further to my query I would like to clarify the following:
It is happening since 2004 all Bom components status (Delivery being processed) all the BOM main items header status is showing completed.
It not impacting the business, but suddenly user raise query SO, DELIVERY, GOODS ISSUED, AND BILLING DOCUMENT completed why still delivery showing as being processed.
1. I have checked at SO level -- all the line items were delivered. ie: delivery, goods issue, billing completed.
2. I checked the Header Level data completed and Item Level data being processed.
3. If I look into the each item level also it is showing as being processed.
4. Even the SALES ORDER HEADER LEVEL showing the status of Completed.
5. Removed credit check in delivery.
The only issue is OUTBOUND DELIVERY DOCUMENT: Status alone it is showing as ' Being Processed' -- surprisingly!
Aditya.

Why PSA data show red status when opened but green on PSA page?

Run RSA1 -> click PSA to open PSA page, locate one infosource and find the PSA under it, find the status column shows it's green, but when opening it, find the 1st column shows red for each row. How does the inconsitance occur?
BTW, if we open the infopackage monitor for the above one, find a weird thing is that each request get two consecutive processes running with a circle of red ball and green ball in the left frame. Double click one of them, in the right frame and click the monitor Status tab, the msg window is as following (in between two dashed lines below):
Incorrect data records - error requests (total status GREEN)
Diagnosis
Data records were recognized as incorrect.
System response
The valid records were updated in the data target and can be used in reporting.
The incorrect records were not written to the data target, but were posted retractively under a new request number in the PSA.
Procedure
Check the data in the error requests, correct the errors, and post the error requests.
Sounds like the data failed to uploaded to data target due to error in PSA, but why the status show green in somewhere? And if clicking the Details tab, all show green! Weird!
Thanks

Hi Kevin,
In your InfoPackage Update tab, click the Error Handling button. It seems that the Valid records update, request green option is chosen. This is why you see the green request and some error records.
This means that the corect reocrds were loaded and are available for reporting, but the incorrect ones were left behind. This is used to check the erro records separatelt so that they do not disrupt the entire data load.
Hope this helps...

How to show network status in top toolbar?

how to show network status in top toolbar? Network preferences is there, but network status has disappeared on last reset of Airport Express, but may not be connected. Thanks in advance for practical help

Interestingly, in my experience, using the method described above of unchecking the "Show Connected Servers" box in the Finder Preferences makes no difference in what I can put in the sidebar. I was able to move a sub-folder of a shared disk to the Favorites section of the Finder Sidebar, but nothing else. (i.e. I could not add the shard disk itself to the sidebar – either to the devices, favorites, or any other section, and I could only add a subfolder of the shared disk to the favorites section – not to the devices section or any other section). This was the same whether I had "Show Connected Servers" checked or not.
I'm running OS X Mavericks, and the setup I have is with a previous generation Time Capsule (i.e. the short, square kind that you could buy before the most recent taller variety came out last year), with a LaCie 3 TB USB 3.0 external drive plugged into the USB port of the Time Capsule. I'm then accessing this network drive over WiFi. The differences in what I'm seeing may be due to some change they made in the way Mavericks handles these setups.
I could also just be misunderstanding what you're saying, but I thought I'd add this in case anyone else gets similar results so that they'd know they're not alone. Let me know if I'm missing something here.

Sales Order Status showing Being Processed

Hi All ,
I my client created sales order with 100000.700 ton and with 42 Piratical delivery document with different dates and 42 billing document and clear accounting documents
But the problem is Sales order status showing as Being Processed
I check all delivery documents if was showing total quantity delivers and i check copy controls OR to ZLF Updated document flow is there
and i Item category TAN don't not having completion rule
My question is it is mandatory to maintain Completion rule in item category
The Problem With Only One sales order it showing Being Processed, rest of sales document Showing completed
Do we need to Updated Status manually ?
Can any one guide me what could be a Problem
Thanks
Rajesh

Hi,
GO TO VA02 THEN SELECT THE ITEM THEN GO TO SCHEDULE LINE -> STATUS TAB-> GIVE THE REASON FOR REJECTION
Regards,
T.Murugu

Has anyone upgraded the Ironport ESA to 8.5.6-074 and had the issues of Raid status showing unknown?

Has anyone upgraded the Ironport ESA to 8.5.6-074 and had the issues of Raid status showing unknown? After we upgraded our appliances we are having issues with our ESA appliances showing the RAID status as unknown. When we reported the issue to CISCO we were updated there were no issues reported at all. Could anyone please confirm if you have experienced the same issue.

You should see OPTIMAL - meaning the drives in the C170 are in good health/status:
myc680.local> version
Current Version
===============
UDI: C680 V FCH1611V0B2
Name: C680
Product: Cisco IronPort C680 Messaging Gateway(tm) Appliance
Model: C680
Version: 8.5.6-074
Build Date: 2014-07-21
Install Date: 2014-07-29 11:16:34
Serial #: xxx-yyy1611Vzzz
BIOS: C240M3.1.4.5.2.STBU
RAID: 3.220.75-2196, 5.38.00_4.12.05.00_0x05180000
RAID Status: Optimal
RAID Type: 10
BMC: 1.05
There are times post-reboot, that you'll see and get notification of RAID sub-optimal --- meaning that the appliance is running through on a health-check of the appliance's RAID. You should be getting a notification once RAID status has returned to OPTIMAL, or as per the older OS revisions, READY:
myc170.local> version
Current Version
===============
UDI: C170 V01 FCH1428V06A
Name: C170
Description: Cisco IronPort C170
Product: Cisco IronPort C170 Messaging Gateway(tm) Appliance
Model: C170
Version: 7.6.3-019
Build Date: 2013-06-09
Install Date: 2014-09-12 13:52:24
Serial #: xxxxxxD87B39-yyyyyy8V06A
BIOS: 9B1C115A
RAID: 02
RAID Status: READY
RAID Type: 1
BMC: 2.01

In Message Monitoring Message showing holding status

Hi
Can anyone solve this problem.Its urgent for me.
My scenario is IDoc->XI->FILE
The file i am trying to generate is an xml file which i am dropping in XI application server using File system.
The problem is when i am going to see the message using transaction SXMB_MONI the perticular message interface is showing waiting for acknowladgement status .
But in message monitoring in runtime workbench the it is showing following status:
Adapter Engine
<b>Holding</b>
18.11.2005 05:42:09
CORP_SAP_DR2_030 http://limited.com/usa/sap_appl/retail/VendorsSAPAPOToMANU
MIIA_Create
BS_MANU
I am in SP14.
Also the output xml file is not getting created in the XI application server.
Please let me know the solution.
Thanks
Debraj Roy

Hi Debraj
HOLDING is a status which occurs normally for EOIO (Exactly Once In Order), so your message is set to Holding means some earlier message has not gone through. So until those messages are through this message will be in HOLDING state.
Have a look at this link which explains how to handle such scenarios.
http://help.sap.com/saphelp_nw04/helpdata/en/49/e3fb40ef74f823e10000000a155106/content.htm
cheers
Sameer
Assign points if it helped you

Payment Card Order completely invoiced but in the order is still showing Overall Status as Blocked

Payment Card Order completely invoiced but in the order is still showing Overall Status as Blocked

Share the screen shot of payment card tab from that sale order. Also what values are flowing in Status tab.
G. Lakshmipathi

GL posting clearing item amount and do not show doc status on the header

Hello,
GL post clearing amount both side and increase the no of items in the GL balance display. Inaddition, these clearing line item document header does not show document status field. I have another GL which does not post extra two lines and clearing item document is empty and header shows document status as A (cleared item).
Could you let me know what the difference and what need to be changed to make it not to post clearing items + and - and show doc status.
Both are same FSG and only difference tick mark not done for balance in local currency.

Thanks for your reply...but thats did not work. As I said earlier, I have a Structure in my rows and 2 characteristics in my free chracteristics and in my columns I have a selection of key figures...
What I want is when I drill down on one of my 2 free characteristics, I do not want to see rows with amounts (KFs) zero or space.
RR

SAP R/3 in order status showing accounting documnet not cleared

Hi All,
SAP R/3 in order status showing accounting documnet not cleared but when i checked in billing document and customer account its showing posted but order showing...same error.
Thanks in Advance..
URS,
PURI......

Hi Venkat,
Please Check the Billing Document its Transfer Status must have been Indicating Not Transferred to R3,Since the Order has Errors in it the Billing Document, Error Order's does not replicate to R3 so the Sales Order need to be made Error Free and Then try to Repost the Billing it shall get Transferred to R3.
Please Suggest the error in Sales Order for Further Help
Hope is Answers your query
Thanks and Regards,
RK.

Workflow attached to content type shows the status as 'Starting'

Hi,
I have developed a workflow to distribute documents from Drop Off library to different SharePoint libraries based on the content type that the document uploaded to.
The drop off library has been configured incoming mail settings hence the documents would be on boarded to drop off library through e-mails. In this scenario, my workflow should be triggered when the document is on boarded through email.
Another scenario, the user can upload the document to different content type manually and updates the respective meta data values. This scenario, my workflow should be triggered when the item updated.
So, I have configured my workflow should run on the content types and trigger when item is created through e-mail and item is updated by manual.
The document on boarded through e-mails are working fine as soon as the item is created.
Issue:
The workflow associated on a content type which needs to be triggered on item created is triggering as soon as the user uploads a document manually and shows the status as 'Starting'.
The workflow associated on a content type which needs to be triggered on item modified is triggering as soon as the user updating meta data values after document is uploaded. Hence, throwing an error
'cannot open a file from drop off' library exception when I try to read file using C# code as file stream bytes.
Configuration:
1. The content types are having mandatory fields which has a default values set.
2. The document version settings are set as check out the document when editing the properties.
Please help me to resolve this bug and let me know if you need more details.
Also, let me know how can we cancel the workflow if it is in 'starting' mode.
The workflow should run the document is onboardedwhen an item is created and

Hi,
According to your description, my understanding is that you want to get data from content type in JSlink.
I suggest you can get the content type data in JSLink using JavaScript Client Object Model.
Here are some derailed code demos for your reference:
http://sharepoint.aspcode.net/view/635399286724222582163436/sharepoint-how-to-get-field-value-using-jsom-jslink-without-async-call
http://sharepoint.stackexchange.com/questions/93777/how-to-get-contenttype-name-in-clientsidejavascript-jquery-csom-etc-in-editf
Best Regards
Zhengyu Guo
TechNet Community Support

Show isdn status shows deactived

Similar Messages

Maybe you are looking for