Show version and snmp sysUpTime differ.

I have an issue on a cisco2600 where the show version uptime shows different to the snmpwalk sysuptime. Any ideas?
Many thanks, Rory.
COGPBR004#sh ver
Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(17a), RELEASE SOFTWARE (fc1)
COGPBR004 uptime is 1 year, 19 weeks, 2 days, 8 hours, 39 minutes System returned to ROM by power-on System restarted at 09:34:37 BST Sat Jun 26 2004 System image file is "flash:c2600-js-mz.122-17a.bin"
loncmss1006# snmpwalk -v 1 -c evian908 cogpbr004 system system.sysDescr.0 : DISPLAY STRING- (ascii): Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(17a), RELEASE SOFTWARE
(fc1)
system.sysUpTime.0 : Timeticks: (28147818) 3 days, 6:11:18.18 system.sysContact.0 : DISPLAY STRING- (ascii): system.sysName.

This is normal as sysUpTime is a 2 bit counter. Thus it will roll back to zero once it reaches the limit (4294967296 timeticks). This equates to more than one year. Notice that your show ver says 1 year, 19 weeks ...
An ehancement request was submitted a long time ago (CSCdm72652), but it was closed for the following reason:
"32-bit sysUptime is as per defined standards and there is no plan to implement a 64-bit version unless the standard is updated to take care of the same."
So, to get this issue resolved, the standard would need to be modified by the IETF.

Similar Messages

WRT610N RIP version and SNMP

I just bought this router ... Never experience the overheating problem posted by other users, router is pretty cold, even after 3 days on In Italy the street price is quite expensive (180€ / 232$) but works great on 2.4G (5G suffer serious lack of coverage)
Just two question
1. Wich RIP version the router uses?
2 There is a way to have SNMP enabled?

1. It uses RIP Version 1...
2. The router(WRT610N) does not support SNMP...

Show version for Cisco Blocker

Hi,
As I am not really tech savvy here, we curently have an issue where we need to verify a serial number for Cisco Blocker. However, customer said they did not have a show version and instead provided us with the system status information. However, from it, we cannot derive the correct serial either. Is anyone familiar with how to interpret the system status to derive the correct serial for Cisbo Blocker? Or are there other options the customer can give us to get the correct serial?
I am attaching the system status provided by the customer.
Thanks,
Cathy

Hi,
As
I am not really tech savvy here, we curently have an issue where we
need to verify a serial number for Cisco Blocker. However, customer
said they did not have a show version and instead provided us with the
system status information. However, from it, we cannot derive the
correct serial either. Is anyone familiar with how to interpret the
system status to derive the correct serial for Cisbo Blocker? Or are
there other options the customer can give us to get the correct serial?
I am attaching the system status provided by the customer.
Thanks,
Cathy
Cathy,
In the attachment you can able to see the serial number under the version area.
Hope to Help !!
Ganesh.H

I can not delete my history and adding new bookmarks. Upgrading to later Firefox versions and/or re-installing didn't help. The address bar still shows the web addresses of old and whenever I make new bookmarks, it's always gone as if it was never made.

I can not delete my history and adding new bookmarks.
Upgrading to later Firefox versions and/or re-installing didn't rectify it either.
The address bar still shows the web addresses of old and whenever I make new bookmarks, it's always gone as if it was never made.
Also, I have noticed that every once in awhile you can not close tabs you've opened, either by pushing on the X button and/or clicking on the mouse to close it. Although closing the window and opening it again (without closing the Firefox application) seemed to rectify the problem in the short term, it's becoming quite annoying.
== This happened ==
Every time Firefox opened
== the Firefox is being used

I think I have a solution.
First, download the add-on SQManager. This should be included with FireFox, it is really good.
Look for the file '''moz_hosts''' in the folder '''places.sqlite'''.
Don't delete the file, just delete the information in the file. My file has over 3600 websites, which go back years!! I did not know they were there, but I was frustrated about not being able to get rid of them. They popped up every time I used the address bar. Clearing my history would not get rid of them.
This is where they are stored!! I found that by deleting the pesky web site from '''moz_hosts''', it does not appear in my address bar anymore!!!
I think that if I just delete all the websites in moz_hosts....
Wa-la...History Gone!!!
As long as you don't delete the file, just empty it, FireFox won't know the difference. It will just keep adding websites to it until you empty it again.
Why running "clear recent history" doesn't do this, I don't know. You are doing manually what "clear recent history" is not doing.
Please tell me if you see any flaw in this.
''I think it's the solution we've all been looking for!''

On a Mac OS X version 10.4.11 and itunes 9.1.1. Can't update to itunes 10.6Trying to get a previously purchased song. Can't use the purchased option under quick link - nothing shows up and won't let me purchase an already purchased song. What can I do?

On a Mac OS X version 10.4.11 and itunes 9.1.1. Can't update to itunes 10.6, Mac too old. Trying to get a previously purchased song. Can't use the purchased option under quick link - nothing shows up and won't let me purchase an already purchased song. What can I do?

If possible you need to upgrade OS X. However, what you can upgrade to is dependent on what your Mac hardware and configuration is which you have not provided in your profile.

After editing in lightroom, i transferred the photo to final cut pro. However the photo that shows in final cut pro is the unedited version and a bit blurry. Any ideas?

after editing in lightroom, i transferred the photo to final cut pro. However the photo that shows in final cut pro is the unedited version and a bit blurry. Any ideas?

IIs there an export function from Lightroom? Did you export? Does the exported file contain your edit?
THe hard drive file size doesn't matter. What matters is the image size, it's dimensions in pixels.
IN FCP press Cmd-J to see the project properties.

I have Screenflow 3.0 (the free version) And it wont record! The icon wont show up near the ichat either!!! How do I make it work?

I have Screenflow 3.0 (the free version) And it wont record! The icon wont show up near the ichat either!!! How do I make it work?

We have a solution available for anyone needing to run Firefox 10 with Read&Write v10 Gold, please email us directly for this temporary resolution- [email protected]

My ipad 2 just shows itunes and plug icon my computer wont take new version of itunes too old how do i get my ipad 2 working do not care about saving data just want to use this very expensive useless item!

My ipad 2 just shows itunes and plug icon my computer wont take new version of itunes too old how do i get my ipad 2 working do not care about saving data just want to use this very expensive useless item!

My iPad2 works great now after IOS 8.1 Update
I did my iPad2 update thru iTunes on my iMac and it was sucking the iMacs memory very low during the update. Safari froze before loading the first web page and I did a hard boot and went fishing as I saw where it was going to take a long time to recover. When I tried again it wasn't quite right and then did one more hard boot and then did a Reset by going to General-Reset-"Reset all Settings" and it works real well now without loosing any data and in-home wi-fi clocks at 17Mbps download. Probably like most of you I’m sticking with OSX 10.9.5 Mavericks as it gets the job done very nicely and don’t need all that extra fancy stuff that probably will slow things down.

Have lossed PSE 12 and dont know my serial No: as i downloaded it it just shows a trial version and tiactiate it it asks for myserial No:

i have lost my PSE 12 Software when I try to start it it brings up a trial version and asks me to sign in and reactivate it but I download the software from Adobe and cannot find my serial number

Hi,
If you go to https://forums.adobe.com/ you should see Manage your Accounts - click on that
Under Plans and Products, click on View All
Then click on View Other Products
That should show you your Photoshop Elements 12 and if you expand the entry it should display your serial number.
That assumes you registered you copy under that Adobe Id
Otherwise, you need to contact Adobe here http://helpx.adobe.com/uk/contact.html
You will probably need proof of purchase.
Good luck
Brian

I had a trial version and my purchased the full version but it is still showing trial version

I had a trial version and my purchased the full version but it is still showing trial version

Chat Now button near the bottom for Activation and Deactivation problems may help
http://helpx.adobe.com/x-productkb/policy-pricing/activation-deactivation-products.html
or
Cloud Getting Started https://helpx.adobe.com/creative-cloud/topics/getting-started.html

Imp and exp on diff version

hi
i have found problem in exp and imp in diff version of oracle
i have take exp in (Oracle8i Enterprise Edition Release 8.1.6.0.0) with no error
but when i imp this dmp on oracle personal edition
(8.1.5.0.0)
then it will gives error
is it possible to takes import data from higher to lower version.
thanks in advance.

Oracle does not allow to import data from higher version to lower version directly but you can do it if you take catexp.sql file from your older version and run that file in the Oracle Server where you have your higher version.
that file is found :
<ORACLE_HOME>/rdbms/admin
after you make the import you have to restablish your higher Oracle Server running catexp.sql beloged to that Oracle Server.
Joel P�rez

Hello am using ios 7.0.4 I have a question about messages that it does not show the time of a particular message after first message that I recive form a paricular person so please in the next version change this and with every message show time and date

hello am using ios 7.0.4 I have a question about messages that it does not show the time of a particular message after first message that I recive form a paricular person so please in the next version change this and with every message show time and date

Hi,
How is everything going? Have you checked this issue from OWA? If so, please let me know the result.
In adition, please also try to use the following powershell commands to check if the assistant has right permissions:
Get-MailboxFolderPermission -Identity
CEO’s email address:\Calendar -User assistant’s email address
Also check with:
Get-Mailbox -Identity CEO’s mailbox
| fl *GrantSendOnBehalfTo
Please let me know the result.
Best Regards,
Steve Fan
Forum Support
Come back and mark the replies as answers if they help and unmark them if they provide no help.
If you have any feedback on our support, please click
here

HT4972 i have a 4.21 version and i need a 4.3 version but it wont show any signs of saying software update underneath the 'about' section

i have a 4.2.1 i pod touch and it says i need a 4.3 ios version and it wont show any signs of software update underneath the 'about' area i dont know how to change this

It is likely you have a 2G iPod. Those can only go to 4.2.1
Identifying iPod models
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

My mac is showing version 10.5.8 and will not update

My Mac is showing version 10.5.8 and I can't get it to update. Can it be upgraded?

Yes, by purchasing the OS you want to install.
(61118)

I restore my US version iphone 5s by connecting itunes after restore it shows hello and select country, and activation, but it does not activating why? is it work in china ?

i restore my US version iphone 5s by connecting itunes after restore it shows hello and select country, and activation, but it does not activating why? is it work in china ?

If the iPhone is locked to a US carrier, you cannot use the SIM card of another carrier on it to either activate it or use the iPhone.
If you want to use your iPhone with China unicom, you need to get it unlocked by your US carrier. Contact them to see what their unlocking policy is and if you qualify.

Show version and snmp sysUpTime differ.

Similar Messages

Maybe you are looking for