Signal Problem MacPro 1.1 w/ATI Radeon X1900 XT

Before I run out an purchase a new video card wanted to run my issue by the forum. I have a MacPro 1.1 (early 2007) with a ATI Radeon X1900 XT card. When booting up recently my screen is blank, no signal. If I switch video ports it fires up.
Is this a video card issue or something else with the OS (running Mac OS X 10.6.6 (10J567))?
Would appreciate a little insight from the forum.
Thanks,
Koyangie

1. There was a replacement program that ended 1/31/2011 for some X1900
2. Any owner by know should have known and been doing a good deep cleaning for dust, and upping the system fans a tiny notch (900 rpm is quiet but more efficient) to keep more air circulating
3. While you can't directly measure GPU temps, you can with other sensors
4. Do you hear the video card fans or system fans working hard?
Poor design with the cooling chamber on X1900 made it a dust magnet and headache.

Similar Messages

ATI Radeon X1900 XT driver for MacPro

I put an ATI Radeon X1900 XT for MacPro in my 2 x 3 GHz MacPro. It displays only 1280 x 800 on my 30" Cinema. Do I need to install a driver, and if so, where to get the driver since card did not come with CD and AMD site has not posted a driver?
2 x 3 GHz MacPro Mac OS X (10.4.8)

zspike --
You don't need drivers -- they're built in to the OS. However, it would be nice to use the ATi displays panel, so you can turn on various app-specific speed settings and features like full-screen antialiasing.
Now, version 4.5.9 of ATi Displays is a Universal Binary, but ATi in their infinite wisdom have made it so that it WILL NOT install on a Mac Pro, only a G5.
But there's a way around this:
http://forum.macbidouille.com/index.php?showtopic=199963
Have a look at post No. 8. Simply put the displays.app in your /Applications/Utilities folder, and run it from there. Runs no problem. I couldn't get the Prefs Pane to work, but all that does is launch the Displays.app
Have fun!

Brandnew 8-core MacPro and ATI Radeon X1900 xt

I had this quadcore MacPro with an ATI Radeon X1900 XT and now I am switching to a newer octo-core MacPro.
I managed to install the card into the computer case. But alas, i don't see anything on my screen...
System Profiler discovers the card but gives it an generic name "Display" with Vendor ATI and DeviceID 0x7249.
But no "displays" found attached to it, which is b.s.
Please please don't tell me i cannot use this graphics card in the octo-core MacPro?!

I am surprised .... I don't have (any ideas), so I don't know for sure
You know, that doesn't help or further things and puts out false ideas that there even might. Then I'll hear "but I read somewhere something."
Apple changed the firmware on 2008. That is well known and pretty obvious, and graphic cards have to follow suit.
Nvidia doesn't seem to know or follow ATI's path of using a "hybred" (for want of better term) EFD? ROM that works across EFI32 and EFI64. Been explained over and over, or if not explained, given as cause to why.
At least we have a few years before EFI128!
NVidia GeForce 7400 gfx card
Now that is very elusive.
The 7300GT works only in 2006-7 Mac Pro, which were dual processor / dual or quad-core, but all used EFI32; 667MHz FBDIMM; had 1333MHz front side bus; PCIe 1.0/1.1 (but not PCIe 2.0 that came out in 2008).
And with brand new 2009, DDR3, you graphic option is really between GTX 285 and ATI HD 4870 - forget the GT120 even as a viable option for most.

Can I put two ATI Radeon X1900 XT's into a MacPro?

Hi
We've just bought a MacPro, with 3 NVIDEA 7300 cards. Sadly it seems the 7300 does not support the apple DVI-Video adapter. Our system requires three dual link DVI ports supporting the adapter, so on face value we should be able achieve this by removing the 7300's and installing two ATI Radeon X1900 XT's instead.
The question is is it possible to put two ATI Radeon X1900 XT's into a MacPro? Has any one done this? or indeed does anyone know how to get the 7300's to recognize a DVPAL device such as video projector or analogue video monitor?
Cheers
Nick
MacPro Mac OS X (10.4.8)

PCI-E (Peripheral Component Interconnect-Express) is a newer implementation of PCI which uses a much faster physical-layer communications protocol than older PCI bus architectures.
Rather than using a bus as PCI did, PCI-E uses dedicated, unidirectional, point-to-point connections known as "lanes" to communicate with PCI-E devices.
The Mac Pro features four PCI-E 16-"lane" connectors on the main logic board. In PCI-E, these are known as "x16" slots. These can be used for PCI-E-compatible cards, like the ATI Radeon card that is available as a configure-to-order option in the Mac Pro.
PCI-E cards will work in slots that are at least as large as the card is. This means that the "x16" slots in the Mac Pro computer also supports "x1" and "x4" cards as well. However, all four slots cannot simultaneously support four cards that implement the same lane configuration. Only one slot actually has 16 lanes going to it—you can put a x16 card into a slot that is only using one lane and it will operate properly, but it will operate more slowly than the same card in a x4, x8 or x16 slot.
The Expansion Slot Utility, located in /System/Library/Core Services, allows you to configure the PCI-E expansion slots and how many lanes each slot will support, as illustrated below. This example shows a "x16" graphics card occupying the first slot, and the other slots are configured to support an "x1" card in slot two and "x4" cards in slots three and four. The example shows the other options available. When you have picked the appropriate configuration of slots to support your compliment of PCI-E cards, click the Save and Restart... button to implement the configuration.
http://docs.info.apple.com/article.html?artnum=304122
Michael

ATI Radeon X1900 XT only for MacPro?

I Just noticed this this morning at Apple's Online Store ( US )
"ATI Radeon X1900 XT Graphics Upgrade Kit US$ 399.00"
I wonder if this will work in the G5 with Dual Cores ( and Quad ) PCIe ?

Ok thanks Jewell, What a Bugger eh?
X800XT for PCI-X G5's and ATI Radeon X1900 XT for MacPro's and nothing for the PCI-E last generation G5's! (unless you BTO).
I have seen your posts here about the lack of video card upgrades for the Quad, and I feel for you ... it's got to be exasperating !!
It will not unfortunately. Its to do with the way
video cards are recognised by the host system and the
x1900 is for MacPro only.
However.
Joe Schorr has confirmed in these forums that ATI
will be releasing a dual-core G5 edition of the x1900
(?) card which would finally make this Apple's first
video upgrade card since the dual-core G5 (quads)
were launched in October 05. Way to go Apple...
I read your repost of it.
-Robert

Problem w Dual Monitors on ATI Radeon HD 4870 512 MB

Hi I'm having problems with Dual Monitors on ATI Radeon HD 4870 512 MB, Mac Pro 2009.
Setup: I'm running two 27" DELL U2713HM Displays at 2560x1440 one via direct DVI cable and the other one thru the Mini Display Port via Dual Link DVI adapter.
Now when I boot up the left screen displays the start-up apple as it should but then both screens go black and the right one (DVI connection) comes on while the left one stays black, goes into power safe mode. When I go into preferences > Displays I even get only one single display as if there were no multiple connected. It's however NOT a connection problem, since it works during the boot up sequence.
Any idea what might be wrong with my set-up? Do I need a new graphics card?

You do have the dual-link adopter connected to USB power right?
Next I would try using a displayport to mini displayport cable. You monitors have:
Connectors VGA, 4 x USB 3.0, DVI-D (HDCP), HDMI, DisplayPort 1.2,
That cable is about $10
http://partnerdirect.dell.com/sites/channel/Documents/Dell-UltraSharp-U2713HM-Mo nitor-Brochure.pdf

Crash with ATI Radeon X1900 XT and second HD display (DVI) ?

hi ! i have a realy tough one for you guys : since 3-4 days i've been getting this realy strange (and scary!) kernal panic screen / crashes / freeze with my macpro dual 2.66 with ati radeon X1900 xt.
the crashes keep coming while doing extensive work (video converting, renders) or just letting the macpro running doing nothing much all night long...
now this is what i found for now : if i disconect my 2nd display (samsung syncmaster 2493hm HD in DVI 1080p) it seem to be stable. when i reconnect it sometime it can run again with this 2nd display for a while but when i leave a render all night long the next morning it will be frozen, nothing on screen (all black).
after rebooting it get this crash report from the system :
Maccinachheeke-pabcapk cat0etiabies 0x00000000000000000000006:
6 ereerr--i oporgingngnkbeaachineck Maehik ne-a0h0h ck stat00t000000000 r0es0
reteattartPvvl Ili maaliceicdn mchk aiog eproMh
rekroi-MCpor reorrosg-:
porttMCrSTregt(i_MC 0xSTATUS(er40_S x20210(0x0nv0TalU00xx002in000iS10000002405)100l00U I0nva0M 0xS
IS(0x0A30:_M0U2(00ATU5S(2xx00200TA00000x00400000IAinv2li00lC
20IAA00200_inv0xid
0IA3: 3_d0000AT0)000000d)0000n00a00d000nA0v0l0d
I3S22_v4USi3SIA0411): 0400 0x0U0000020000 00100 00vl00
0 I0A3011CivAA32_SM_441SxTUTb0004100)000vb01001iA 00led 0I cva00 i e r cI:S(0xe0 1 ):(0 : 041e5)b x000b 800de:fix 4arrld
Mo MAA e8atr code inf 00: 0 0x00 St
00s00ode
spSccifsic codr
texr ccorre02sor:
0 8O4x0
r erder in orrmt n ded0000: 0x1rp0000Satus bitts:
b 0ts:4ssor PMroexce Chtsscorrupt, tconad:
e0x3re1cor,rtr epo:bl ed err: E0)roncirters0: 0
8ernc0ro,rrR2: 0xected error
CR3: 0x00e7a000, CR4: 0x000006e0
EAX: 0x24f9bed8, EBX: 0x1a6f198a, ECX: 0x1a6f198a, EDX: 0x004bc870
ESP: 0x24f9bebc, EBP: 0x24f9bf08, ESI: 0x00001e27, EDI: 0x035e1718
EFL: 0x00000006, EIP: 0x0019e9c0
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x439d58 : 0x128d0d (0x3cc65c 0x439d7c 0x131f95 0x0)
0x439d98 : 0x1a42cb (0x3d27fc 0x0 0x35e1718 0x12)
0x439f58 : 0x19c103 (0x439f70 0x0 0x0 0x0)
0x24f9bf08 : 0x135888 (0x1a6f164f 0x35e3d40 0x3f91084 0x2)
0x24f9bf58 : 0x1359c9 (0x13d8a2 0x0 0x0 0x19e23a)
0x24f9bf78 : 0x13da53 (0x13d8a2 0x0 0x0 0x0)
0x24f9bfc8 : 0x19b21c (0x0 0x0 0x19e0b5 0x4ebf4c0) Backtrace terminated-invalid frame pointer 0x0
Kernel version:
Darwin Kernel Version 8.11.1: Wed Oct 10 18:23:28 PDT 2007; root:xnu-792.25.20~1/RELEASE_I386
Model: MacPro1,1, BootROM MP11.005C.B04, 4 processors, Dual-Core Intel Xeon, 2.66 GHz, 2 GB
Graphics: ATI Radeon X1900 XT, ATY,RadeonX1900, PCIe, 512 MB
Memory Module: DIMM Riser A/DIMM 1, 512 MB, DDR2 FB-DIMM, 667 MHz
Memory Module: DIMM Riser A/DIMM 2, 512 MB, DDR2 FB-DIMM, 667 MHz
Memory Module: DIMM Riser B/DIMM 1, 512 MB, DDR2 FB-DIMM, 667 MHz
Memory Module: DIMM Riser B/DIMM 2, 512 MB, DDR2 FB-DIMM, 667 MHz
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x87), Broadcom BCM43xx 1.0 (4.170.13.1)
Network Service: AirPort, AirPort, en2
PCI Card: ATY,RadeonX1900, Display, Slot-1
Serial ATA Device: ST3250820AS P, 232.89 GB
Parallel ATA Device: OPTIARC DVD RW AD-7170A
USB Device: USB2.0 Hub, Up to 480 Mb/sec, 500 mA
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: USB RECEIVER, Logitech, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mA
FireWire Device: built-in_hub, unknown_value, Unknown
FireWire Device: GSA-5163D Super Multi DVD Rewriter, HL-DT-ST, Up to 400 Mb/sec
FireWire Device: My Book Device, WD, Up to 800 Mb/sec
here's my complete config if it can help :
Model Name: Mac Pro
Model Identifier: MacPro1,1
Processor Name: Dual-Core Intel Xeon
Processor Speed: 2.66 GHz
Number Of Processors: 2
Total Number Of Cores: 4
L2 Cache (per processor): 4 MB
Memory: 2 GB
Bus Speed: 1.33 GHz
Boot ROM Version: MP11.005C.B04
SMC Version: 1.7f8
ATI Radeon X1900 XT:
Chipset Model: ATY,RadeonX1900
Type: Display
Bus: PCIe
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 512 MB
Vendor: ATI (0x1002)
Device ID: 0x7249
Revision ID: 0x0000
ROM Revision: 113-A52027-140
EFI Driver Version: 01.00.140
Displays:
SyncMaster:
Resolution: 1920 x 1200 @ 60 Hz
Depth: 32-bit Color
Core Image: Hardware Accelerated
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Rotation: Supported
Television: Yes
S/M 955SL:
Resolution: 1280 x 1024 @ 75 Hz
Depth: 32-bit Color
Core Image: Hardware Accelerated
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Rotation: Supported
anyone ever see this problem ? at 1st it seem to be related to my ATI card... but i'm no expert so if anyone can understand part of the crash log let me know ! thanx !!
also forget to say : did all the full apple hardware test + tech tool pro test (app that come with apple care) and nothing was wrong, all ok.
+
francis.t
montreal
Message was edited by: francis.t

Are you really still running 10.6.3? you will need 10.6.5+ so do that and make a clone.
ATI 5770 from Apple Store - like 1000s of others have done and in the comments section on the store page.

ATI RADEON X1900 XT Bad resolution display with SNOW LEOPARD

Hi all!!
I just install a clean version of snow leopard 10.6.2 on my mac pro and everything works good.
Only problem I have, less resolution choice.
I am stuck with 1600x1200 60 Hz but before I was in 1600x1024 76hz.
This mac has a ATI RADEON X1900 XT graphic card.
I try on different mac pro with geforce and the resolution display is good.
It is not the problem of the graphic distorsion in top site of safari,
It's totally in the display.
Thank you!
BP

I use the same video card without any difficulty, under 10.6.2, in an older MacPro. If your card works OK in Leopard, then it's not likely to be a hardware problem. If it happens in Leopard, too, then a hardware failure is possible.
If this happened to me I'd clean the card's contacts, make sure that its supplemental power connection was tight on both ends, and re-install the card.
If the problem remained, I'd try the card in a different slot. If it persisted, I'd do a clean-install on a different drive and boot from it. If the problem recurred with a clean-installed second boot drive, then I'd suspect a hardware problem on the card or, less likely, on the logic board.
At this point I'd visually inspect the "GPU PRESENT" LED on the logic board, under the memory cage, next to PCI slot 1. As you use something completely non-conductive to press the "DIAG LED" button, which is adjacent to the diagnostic LEDs, see if the "GPU_PRESENT" LED comes on. If that LED stays off, it means the machine's EFI (extensible firmware interface) was unable to configure the graphics card, which would indicate a hardware problem on the graphics card, or possibly on the logic board. If the diagnostic LED comes on, it means EFI could configure the card. This does not necessarily mean that the card is functioning properly. The LED staying off, however, would strongly suggest some kind of a hardware problem.
If you have access to another graphics card, see if a similar problem occurs using it. Short of a thorough circuit-check in a shop, that's the only practical way to determine if it's a PCI card or logic board problem. Either way, there'd be a hardware repair/replacement on the horizon.
Message was edited by: Hominahomina

ATI Radeon x1900

My MacPro was purchased with Tiger and a ATI Radeon x1900 graphics card. Anyone know if the card will run when I do the Snow Leopard Upgrade? I first contacted AMD, and they replied back stating I need to contact Apple about this.
Message was edited by: John Luke1

If the Mac Pro was purchased with an Apple-provided (built-to-order) ATI Radeon X1900 XT graphics card installed, you should have no problems booting with the Snow Leopard installer disc. You might have some problems if it was a retail card bought separately.

What is a good replacement for the ATI Radeon X1900 XT on a late 2007 Mac Pro

I recently took my late 2007 Mac Pro to the Apple Store because it was running quite loud. They diagnosed the problem as the fan on the ATI Radeon x1900 XT video card. Whie the card works fine otherwise, I was thinking of replacing it. I noticed some online recommendations that I need to upgrade to perhaps the Radeo HD 4870 if I want to install FCP X on this machine. I do use the Mac Pro for video editing, but haven't switched yet to FCP X. Anyone have a suggestion on a replcement video card that will work both on this machine and will be compatible with FCP X.
Thanks for any advice.

<http://store.apple.com/us/product/MC742ZM/A/ati-radeon-hd-5770-graphics-upgrade- kit-for-mac-pro-(mid-2010)>

After Effects 7 with ATI Radeon X1900 XT

Hi everyone,
I use Adobe After Effects 7 a lot and I'm not happy with my current machine (PowerPC G5 2x1.8GHZ, 2GB DDR SDRAM, ATI Radeon X800 XT), it is too slow to work smoothly when I have several layers and effects going on. Previewing the work on the timeline (OpenGL or Adaptative resolution) is painfully slow and takes on my nerves. I believe this is mainly due to my graphics card, and the fact is not 100% compatible with OpenGL on After effects.
I'm ready to upgrade with a Mac Pro 2.66 GHz Quad Xeon with ATI Radeon X1900 XT, but only if I'm going to enjoy a real improve with After Effects 7, as this is my main editing application right now.
Does anybody have experience with this configuration?
Thanks in advance for reading and replies!
PowerPC G5 2x1.8GHZ Mac OS X (10.4.7) 2GB DDR SDRAM, ATI Radeon X800 XT

I have this configuration, but sadly have had no time to play around with After Effects. AE's realtime playback capabilities are limited (especially when compared with something like Motion), so you're probably still going to be rendering to RAM a lot. I believe the OpenGL support is for things like anti-aliasing, blur, and blending modes -- so a faster video card may not automatically equal huge performance boost across the board. Four Xeon cores and a lot of RAM will help it a lot more (see exception below).
Also, AE 7 still has to run under Rosetta which results in a slower performance than if it was native. Also, be aware that there is a limit placed on all Rosetta processes that do not allow them to address more than 1.5GB of RAM combined. This will most likely limit your render speed and preview lengths. See this thread on Adobe's forums for more info:
http://www.creativecow.net/articles/jonesgraham/AE7_on_IntelMacPro/index.html
EDIT: The above link was to the performance comparisons, but not the original Adobe forum thread. Here it is:
http://www.adobeforums.com/cgi-bin/webx/.3bc2401b
However, if you read the thread, and follow the link in it, the author is seeing huge performance gains with AE7 on his MacPro 3GBs over his old dual G5 4.5GBs.
So most likely, you'll see a performance benefit from upgrading. And when an Intel native version of AE ships, things will really fly.

ATI Radeon X1900 worth it for only FCP and Color?

Hello,
I've been looking around these posts for a while and I can't seem to find this specific answer, so I apologize if my question has been asked already.
I am looking to purchase a MacPro tower. I don't use Motion. I don't play video games. I don't need 8 zillion giant monitors. I intend to use the computer mainly for Final Cut Pro 6.0 and probably a fair amount of Color as well.
With this being the case, what are the benefits of the
ATI Radeon X1900 XT 512MB Graphics Card, over the
NVIDIA GeForce 7300 GT 256MB Graphics Card? Is it really worth the money? I've seen some posts that say you won't see a difference in FCP, but is this also true for Color? And if so, what exactly will the difference be?
Thanks,

Here's what they said at the Color board...
With anything less than an ATI x1900...you may experience issues such as lack of realtime playback, missing support for 10-bit images and 2K frame sizes, no float support for your grade settings.
For this version of Color, ATI is the way to go. I wouldn't go so far as to say an Nvidia card gives you a crippled version of the program, but it's close.
http://discussions.apple.com/thread.jspa?messageID=4611284&#4611284
http://discussions.apple.com/thread.jspa?messageID=4672792&#4672792
http://discussions.apple.com/thread.jspa?messageID=4620097&#4620097

Please help: what options do we have other than ATI Radeon X1900 XT

I think my video card (ATI Radeon X1900 XT) is about to die and I'm trying to figure out what to replace it with. (I'm on a 1st gen MacPro, still on Tiger).
What I can't easily figure out from this site, however, is a list of alternative cards I could purchase that will fit in this machine. I gather from the ratings that the ATI X1900 has failed for just about everyone that has used it intensely. And I'd like to avoid buying the same one that is about to fail for me now, but how can I tell what my alternatives are and if they will fit in the slot and/or be compatible with my machine?
I have been to the Mac Pro spec area, and it lists these as the "build to order" options:
* ATI Radeon X1900 XT 512MB (two dual-link DVI)
* NVIDIA Quadro FX 4500 512MB (stereo 3D, two dual-link DVI)
* Two NVIDIA GeForce 7300 GT 256MB
* Three NVIDIA GeForce 7300 GT 256MB
* Four NVIDIA GeForce 7300 GT 256MB
are those the only cards I can choose from? Are there any other better options?
Forgive me if I sound like a totally idiot. I'm just trying to learn...

You should visit Bare Feats and see the various reviews and benchmarks. You have several options now available besides the ones that came originally with your model. There is now an NVidia 8800 card in a version for pre-2008 MPs, the ATI 2600, and the new ATI 3870 just released. You can learn more at Bare Feats and by searching the MP forums.
You have posted this topic in the MacBook Pro forum which is the wrong forum for your question.

Leopard ATI Radeon X1900 XT Freezing Issue, fixed with 10.5.2?

Mac Pro (8-core) original 3.0Ghz 8 core. Purchased October 2007. Ran Tiger 10.4.10 from the box. updated to 10.4.11. ATI Firmware update was not required as it was pre-installed. Never had a crash. Installed Leopard 2 days after release. Installed 10.5.1 the day of release. No problems so far...
A week later watching the "Jelly" iTunes Visualizer, the Screen froze, but iTunes kept playing... The machine was reachable over SSH but very much useless as a reboot command hung. Hard reset, went about my business. A day later unit froze during iTunes Jelly Visualizer again. this time music also crashed. As I approached to reboot the unit noticed very loud video card fan noise. Extracted the burning hot card, later compress air removed some clogging dust bunnies. Reinstalled card and no more freezes for 2 weeks. Freezes again, this time watching youtube in Safari. Made sure data backup is up to date. Performed an Archive and Install of leopard, ran all updates to 10.5.1. This time Mac Pro was fine for a week .... *Freeze*.
Called apple care, after having to explain to a rep what itunes visualizer was, referred to iPod specialist, who transfered me to Mac Pro specialist, 1 hour later, thoroughly explain issues to rep, who after 45 minutes was convinced issue with HW and not SW . Apple sends Do It Yourself repair video card. I replaced it. 4 days later unit Froze again. This time watching movie on VLC...
A week later 10.5.2 was released, and shortly thereafter Leopard Graphics Update 1. So far **nervously knock on wood** no more freezes. I am hoping that whatever black magic was included in these recent updates fixes the Leopard crashes with ATI Radeon X1900 XT. Needless to say this is the last ATI Radeon I "buy".
I need to know and track other users findings issues and experience with Leopard and the ATI Radeon X1900 XT on a Mac Pro. Been reading about a lot of issues with Leopard and the ATI Radeon X1900 XT on the these boards. Google turns up info galore. ...
I am holding my breath

Spoke too soon. Today as I was leaving the house I set the Mac Pro to sleep. When I attempted to wake the machine upon return, display 1 became all garbled. Display 2 was still visible and the mouse moved, but I was not able to click any windows. I ssh'd in with my macbookpro and was able to do a "sudo reboot". In the process it got stuck and in a loop I received:
Feb 17 16:02:37 octagon kernel[0]: ** ASIC Hang Log End **
Feb 17 16:02:38 octagon kernel[0]: ATIRadeon::waitfor_rbspace: Overflowed block waiting for FIFO space. Have 0, need 5. RBBM_STATUS 0x9001c100
Feb 17 16:02:50 octagon kernel[0]: ** ASIC Hang Log Start **
Feb 17 16:02:35 octagon kernel[0]: 860:0x02090000
Feb 17 16:02:35 octagon kernel[0]: 861:0x00002808
Feb 17 16:02:35 octagon kernel[0]: 862:0x00020004
Feb 17 16:02:35 octagon kernel[0]: 863:0x00100000
Feb 17 16:02:35 octagon kernel[0]: 864:0x00840000
Feb 17 16:02:35 octagon kernel[0]: 865:0x00008020
Feb 17 16:02:35 octagon kernel[0]: 866:0x00100000
Feb 17 16:02:35 octagon kernel[0]: 867:0x0a040000
Feb 17 16:02:35 octagon kernel[0]: 868:0x00010000
Feb 17 16:02:35 octagon kernel[0]: 869:0x00002808
Feb 17 16:02:35 octagon kernel[0]: 870:0x00020004
Feb 17 16:02:35 octagon kernel[0]: 871:0x00100000
Feb 17 16:02:35 octagon kernel[0]: 872:0x00040000
Feb 17 16:02:35 octagon kernel[0]: 873:0x00008024
Feb 17 16:02:35 octagon kernel[0]: 874:0x00100100
Feb 17 16:02:35 octagon kernel[0]: 875:0x0a040000
Feb 17 16:02:35 octagon kernel[0]: 876:0x02090000
Feb 17 16:02:35 octagon kernel[0]: 877:0x00002808
Feb 17 16:02:35 octagon kernel[0]: 878:0x00020004
Feb 17 16:02:35 octagon kernel[0]: 879:0x00100000
Feb 17 16:02:35 octagon kernel[0]: 880:0x00840000
Feb 17 16:02:35 octagon kernel[0]: 881:0x00009020
Feb 17 16:02:35 octagon kernel[0]: 882:0x00100000
Feb 17 16:02:35 octagon kernel[0]: 883:0x0a040000
Feb 17 16:02:35 octagon kernel[0]: 884:0x02090000
Feb 17 16:02:36 octagon kernel[0]: 885:0x00002808
Feb 17 16:02:36 octagon kernel[0]: 886:0x00020004
Feb 17 16:02:36 octagon kernel[0]: 887:0x00100000
Feb 17 16:02:36 octagon kernel[0]: 888:0x00840100
Needless to say I had to hard reset....

Television and TV Recording with a ATI Radeon X1900 XT 512MB equip Mac Pro

I have been looking into a Mac Pro 2.66-3.0 Dual-core equipped with a ATI Radeon X1900 XT 512MB. One of the things I would like to accomplish is to also use the thing as a television and TV recorder (reliably). I have experience with the a PC equiped with a ATI9700pro all in wonder. I had nothing but problems with the software with hours (weeks) spent trying solve the issues. Turns out this is not an unusual thing with the ATI-Allinwonder. Thought I would check here to see whether anyone has input on how the x1900 works on the mac pro esp as a tv device.

the elgato system is an external tv tuner that connects by USB. It has nothing to do with the graphics card in your mac.
you can connect an antenna, cable, s-video or composite. Some of the models accomodate HDtv now.
the results are clean, and i've had no problems.

Signal Problem MacPro 1.1 w/ATI Radeon X1900 XT

Similar Messages

Maybe you are looking for