Signature Printing

Hi ,
I got the requirement to print a signature on the check. they gave me
Font call : <esc(4B<esc>(S1p0.37h33.0v0s0b102T
they are asking me use it. Is there Hex converter to convert this ascii or char or num. How to do that? I got the information in one of the forums that if you use this in HEX..ENDHEX, we cant able to print. We need to change in some other format and print it. can anypne please clarify on this...
Regards,

Hi Krishna,
I have a similar requirement to upload the signature to the printer and print the same on checks. We hava a hp laserjet 4250 for this purpose .
Can you share the steps you had to follow to load the signatures on to the printer and in which format, and steps to be followed in SAP to print them using the sapscript form.
Appreciate your help on this.
ma01wo at gmail dot com is the mail id in case you need to send me any document.
Thanks
Rupendra

Similar Messages

Signature printing issue

hi gurus,
We have problem with our AP check printing.
The printer has chip where our CFO's signature resides. And when you print the check from Production System, it prints the signature. But when you print the check from Development and Test system, it Prints an exclamation mark.
Now we have to move to the new printer, we are just changing the network cable to move from old printer to new printer.
And trying to print the signature from Production system to new printer but its still giving an exclamation mark.
New printer also has chip with CFO's signature.
Our Sapscript and Print Program both are copy of standard program and then added some code in there(customized), but in both i dont see any code where it differentiate between systems and prints the signature.
I am debugging only the customized code not the standard code.
Do you think signature printing (based on system) can be in standard code? or in SPRO settings? or in custom code (and i am missing that)? or in Printer setup or any other place which i could not think of???
Please help!! printer needs to be changed by next week.
Any suggestion would be helpful.
Thank You!!!

There are a couple of methods available to print the digital signature.
1) The digital signature is stored in your printer or DIMM module installed in
your printer.
If this is the case, usually there is a certain command sequence to
activate the signature and a code for the signature.
In a previous situation the command used to activate the signature
was \e(201Q\e(s0p2h72v0s0b201T and abcdef was the signature code.
The way this is normally done is to create a print control in your
device type containing the command sequence to activate the signature.
   SPAD -> Full Admin -> Device Types -> <Device type>
         -> tab Print Controls
So for the example mentioned above, create a new print control called
ZSIGN with the contents:
   \e(201Q\e(s0p2h72v0s0b201T
Do not set the Hexadecimal flag for this entry.
In the window of the SAPSCRIPT form used, try it this way in the
old line editor:
<32>
   /: PRINT-CONTROL ZSIGN
   = abcdef
This is the general method used if the signature is stored in the
printer. Of course the command sequnce may be different in your case.
Also see the following Notes about the use of the command
PRINT_CONTROL in Sapscript forms:
    66478 - Use of PRINT-CONTROL in SAPscript
    400379 - Output with PRINT-CONTROL does not work
2) A second method that is sometimes used is that the digital signature
is uploaded as a graphic into the SAP system via transaction se78.
Please see the following Note about print graphics from SAP:
39031 - Print/fax bitmap graphics from SAPscript
For further details also refer to http://help.sap.com
search -> Bc Printing guide
Regards.

Check printing - signature print on check??

I was wonderng if anyone here has any advise on how to print a check with signature on a check. Our company is looking at a printer that will put the signature on the check but the company says we would have to supply on the form a "font call function" so the printer knows where the signature would go. Has anyone else tried printing in this way?
Thanks,
Kurt

Our printing is done using standard PCL printers (HP, Xerox, Lexmark). We just scan the signature, turning it into a graphic (gif, jpg), and then place it on the form as a logo using designer.
Are you sure that Output Designer even has a driver for this particular printer? A quick purusal of the "presentment targets" that came with version 5.5 seems to indicate that - besides some label printers - pcl & postscript printers is what it supports.
Even the Print Agent font reference commands are referring to the "internal" fonts included within the template (as a result of the selected "presentment targets").
I can remember a printer we used years ago requiring that the signature be a font - but it wasn't a pcl/postscript printer and that was prior to us moving to Output Designer. This was a font that was permanently loaded on the printer and a printer command sequence activated it and then a string of characters (like "abcd") caused the signature to be printed.
Without knowing anything about the printer, I see two possibilities if a graphic image can't be used. 1) The font is permanently installed on the printer and you might be able to imbed within your document the command string that causes the signature to be printed; or 2) the font can be installed on the designer PC and thus added to the available fonts for the presentment target and used like a normal font (this requires that the printer be able to accept downloaded fonts).

Signature Printing using escape sequence

Hi Friends
I am trying to print the signatures in cheque using printer escape sequence, But in output no output was printed.
Customer provided the hexadecimal value for escape sequence, I checked the value in SPAD transaction also, both are same.
But I am not able to identify the problem.where exactly-please give your valuable inputs on this.
Thanks
Gowrishankar

Gowrishankar, you just closed 3 of your threads without giving any feedback (read forum rules if you didn't).
Forum is not a self service: for each question you ask, you MUST give feedback to help others who might have the same question.
Could you please give one in each of these 3 threads?
Thx a lot
sandra

Signature printing (very general question)

Okay not really an InDesign question, but I know a lot of you know more about printing than I do. I'm strictly on the design end of things:
I always hear about 8-page and 16-page signatures, yet I know as long as my documents are in multiples of 4 I have no trouble getting them printed. What does the printer do when I send him a 76-page magazine? Is it more difficult to print than an 80-page one? I don't know that much about the actual printing though I'm planning to tour a printing plant next week. :-)
Just curious.
Thanks, Phyllis

It's best to talk to the printer because it depends upon the press or presses he is using. It is the size of the press that determines the size of the signatures.
The printer could print four 16 page signatures on one press and three 4 page signatures on another. He could print 80 pages and throw out the waste. He could move the job to a smaller press. His decisions will be based on time and cost. And that will depend upon the size of the press run, the stock, at any number of things. So back to the top, talk to the printer. (And bear in mind that not all printers are created equal. Some are set up for doing odd jobs, and short runs, some aren't.)

Print Digital Signature

Hi Experts,
I've setup the digital signature for certain document types. Now when I print those signed document, am not able to get the approver's signature on print out.
From the SAP Help I found below link and it says that I've setup ' allowed' or 'possible' option for Document Display in Digital Signature Strategy.
http://help.sap.com/saphelp_sm71_sp01/helpdata/en/45/f0f4a900b404abe10000000a114a6b/content.htm
I tried both the options and still not able to see digital signature during the print out or document display.
In the Help (above link) it also says that
"The document display and print option are not available to the signee if the forbidden option is set in the system table for the entire application."
Where can I find the System Table to remove the forbidden entry for the application?
Do I need to setup anything else to enable the digital signature print option?
Thanks,
Shaun

Hi Amit,
I am not sure on how to get the the signature of the person who released the PO, because as per my understanding the Relase Strategy i.e the Relase code is attached to a Basis profile.
What I would suggest is if you can get all the guys who can release a PO and define him as a Purchaser ie. a Purchasing group then it would be easier to print his signature in the PO.
Here are the Highlevel steps
1. Just have the Signature you want to print in a Tiff format.
2. You can upload the signature as a standard Text using program RSTXLDMC to upload and give a text name.
3. call the text name in your sap scripts.
reward if useful.
Thx,
MJ

Check Signature Only Prints On First Check

Hello,
We're using the SAP-provided Check SAPScript, along with a printer that stores the check signature on the actual printer. So far, we've been able to get the signature to print on the check form, however, when we try to print multiple checks in one single spool request, the signature only prints on the first check form, and does not print on the subsequent check forms. On the other hand, if we create only one spool request per each check, the signature prints each time... Very strange...
Has anyone ever run into this issue or have any recommendations?
Thanks,
Matt

Hi,
Remove that 'at Start of Table' check box and check it.
Regards
Muthappan.

How can I create an electronic signature to use on my email?

''locking as a duplicate - https://support.mozilla.com/en-US/questions/811562''
When I have completed an email, I would like to have a signature print automatically my name, title, address, etc. How do I create this "signature"?

Firefox doesn't do email, it's a web browser.
If you are using Firefox to access your mail, you are using "web-mail". You need to seek support from your service provider or a forum for that service.
If your problem is with Mozilla Thunderbird, see this forum for support.
[http://www.mozillamessaging.com/en-US/support/] <br />
or this one <br />
[http://forums.mozillazine.org/viewforum.php?f=39]

AP Check printing setups for printing checks on your own

HI
I am wondering if there a good document which deals with AP check printing with MICR and signature on your own check stock
thanks

Recently we started to deal with AP check printing in our organizatin. It was a daunting task with the information and resources scattered all over and missing critical pieces of information to make sense out of the whole process flow. We attempted to go through the AP check printing internally and succeded.
I decided to post the information for the benefit of people about the our experience
Check Printing Basics and Beyond for Printing Checks on Your Own
by
Sarma Chilukuri
This article deals with what is needed to get your own checks printed. It is a first attempt to uncover all the hidden rules that one should be aware to get your own checks printed. The first section deals with the basic AP check printing setup, while the 2nd half explores some of the flow of events that make it possible to print the check.
Part I â Basic Setup
AP Setup for check printing
There are multiple steps in the AP check printing. First set of steps deal with the AP side setups. The second step is to get the System side setups. The system side setup deals with printer setup and program options setups. The last step would be to make the print format files configured with the vendor provided escape sequences in the laser print format file.
Step 1: login as Payable Manager
Step 2: Bank Setup: Navigate to Setup: Payments > Banks
1.     Make sure the Bank # etc are present
2.     Tab to âBank Accountsâ, and make sure your account # has been setup
3.     On the Bank Accounts screen, tab to the âPayables Documentsâ and verify that Payment format (E.g., COK Laser Format) has been entered. This âPayment format links to next section where we associate it to the right payment program.
Fig 1. AP Payment Bank Setup Screen
Step 3: Program Setup (Setup: Payments > Programs)
As we know there are only 5 formats 3 of which are âEver Green Laserâ (APXPBFE G|L|F) which are explained in the AP Users Guide. For your own form printing, you have to associate the format to APXPFEL (laser format) program. Also, the APXPBFEL or APXPBFEF call the APXPBFEG, which is the base program that pulls the data from oracle base tables. APXPBFEL is the one which allows us to print the checks with MICR and signature on a plain paper not on a pre printed stationery.
Fig. 2 AP Payment Format Setup Screen
Printer Styles, Drivers setup
The above process summarizes the AP Setup. As a DBA, the printer setup needs to be validated. The base install provides the right setup to some extent. But the differences in printers and print queues may add some complexity to the final configuration. The following section discusses the set up the base install provides and changes as needed.
Step 1. Login as system Administrator
Step 2: Style (Install : Printer > Style)
Look for the âPORTRAITHPLJ4LASCHECKâ. This one is associated with the SRW Driver Called, âAPLASPâ (AP Laser printer format).
Step 3: Driver (Install : Printer > Driver).
     1. The âPORTRAITHPLJ4LASCHECKâ is associated with a âUser Driverâ of PORTRAIT for HPLJ4 and and a SRW driver of âAPLASPâ
     2. Also notice that there is an Initialization string at the bottom of it. This initialization string gets called as pre-report trigger for the APXPBFEG program (APXPBFEG.rdf) file. It sets the kind of format it should be. Please see the Appendix A for details on these printer pcl code translations. The Initialization string was as follows:
Initialization: /eE/e&l0o2a7C/e(s0P/e(8U
Step 4: Printer type (Install : Printer > Register)
Each printer type is associated with a set of styles. Make sure the printer that was selected has the above style and its associated driver listed against that.
Fig. 3 System Administrator Printer Seups
Step 5: Program Setup (Concurrent > Program > Define)
This step holds the key for check printing. It is necessary to define whether you need the check on top followed by the Stub or the other way around. The way it is controlled is based on the APXPBFEG.rdf, the report definition file and the APLASP.prt (Printer Style associate with the Portrait laser check format SRW driver). The APLASP.prt file ($FND_TOP/reports) has two identical setups called the 100 series and the 200 series. Those identical sets of setups define where the MICR and signature print on the check. The following table lists the some of the codes in the 100 series. Please refer to Doc ID #146452.1 for complete details.
Fig. 4 System Administrator Concurrent Program Definitions
CODE #     Code Definition
100     Electronic check activation string
101     1st Check #
102     2nd Check #
104     Deactivate check number mode string
111     Activate MICR line
112     MICR Deactivation / reset the printer head position
121     1st Signature
122     2nd Signature
141     Address font activation string
199     Return to default state string
Table 1. APLASP.prt -- MICR Activation Codes
The above code block repeats itself the same way in the 200 series. The decision to activate one way or the other controls the Check printing.
Step 2: Setting up the Option block
In the concurrent program definition for the APXPBFEL, there is an Options block in the middle. You need to list the codes that you want to activate. Please refer to Doc ID # 186640.1 for some explanation on these.
E.g.,
p_printer_code_mask="201,211,221,241" p_sig2_amount="" p_sig3_amount="" p_sig1_vendnum="" p_sig2_vendnum="" p_sig3_vendnum="" p_country_to_ignore="US" p_continuous_stationery="N"
Step 3: Output format is Text
Text format is sufficient, as the printer will pick up these escape sequences anyway.
Fig. 5 System Administrator Concurrent Program APXPBFEL Options Definition
UIPRINT.TXT, UIFONTS.ALI
One needs to be aware of a few more pieces in this puzzle. The UIPRINT.TXT identifies to the Oracle Applications the print queues that were setup. This file is needed to set your PCL / Post Script printer definitions. I did not have to really tinker with these files other than identifying the PCL and Post Script Qâs that were setup on the UNIX box.
Part II: Integrating all the pieces
The above setups are all documented in various articles. We need to understand a few more steps to see how all these pieces come together.
What you need to know about APXPBFEG.rdf
APXPBFEG (.rdf) is the report file which when called pulls the data from Oracle. If you open the APXPBFEG.rdf in the Oracle reports, there is initialization to the report called, SRW.Init. This will bring in the initialization string associated with the PORTRAITHPLJ4LASCHECK driver definition file. Also, please be very careful with this report format file. When you open it, there is small tiny empty block. in the first block which calls the printer initialization code 100/200 under the Format Mask (from APLASP.prt). If this portion gets changed or messed up, one can end up with some unexpected results. Each of those blocks like MICR, CHECK etcâ¦ have associated format triggers and printer codes.
Please make sure that the printer mask is properly handled. I noticed that the 200 series MICR (211) and Signature (221) printer masks were tied to 111 and 121 respectively. These should have been 211 and 221. The other place you need to be careful was the printer code before and after is proper.
For E.g.,
For the MICR, the âprinter code before and after columns â should be 111 and 112 (or 211 / 212) respectively while Format Trigger should reference to 111 (211).
Fig. 6 APXPBFEG rdf file printer mask and Format Triggers
The escape sequences in the APLASP.prt file for these codes will play the crucial role in getting our format around the report output that gets generated from the APXPBFEG program. Please refer to the explanation of these escape sequence codes in the APPENDIX A.
At this point when you run the program, you will see that the formatted output report file will have all the initialization strings and the output associated with that. You can compare the fields and verify the results. Let us closely examine the parts of the 111 and 121 where the micr and signature prints. The key to this to code the escape sequences the right way to get the associate MICR and signature print out correctly.
Fig. 7 APXPBFEG rdf file MICR printer mask and Format Triggers
Code 111 and Code 112 from the APLASP.prt file.
I broke the line into pieces to illustrate the exact escape sequence code.
Code "211"
Part 1: esc "&f0S" esc "&f0y0X" esc "&l0E" esc "&a0L"
Part 2: esc "(8M" esc "(s0p8.00h8.0v0s0b80T" --- This will be provided by the ROM
Cartridge provider
Part 3: esc "&k15H" esc "*p3215Y" esc "&a13.8C"
code "212"
Part 1 : esc "&f1x3x8X"
Part 2 : esc "&f1S"
Let us go over these 2 sets of codes carefully.
Escape Code     Meaning     Comment
esc "&f0S"      Push Cursor Position
esc "&f0y0X"     Define Macro ID 0 and Start Macro Definition
esc "&l0E"      Define Top Margin at 0 Lines
esc "&a0L"      Define Left Margin at Column 0
esc "(8M"     8M Symbol SetNote : As per pcl codes this happens to be Font Primary JIS Math 8 symbol     MICR Part 1 : Provided by the Vendor from where you the ROM cartridge
esc "(s0p8.00h8.40s0b0T"     {Fixed Pitch}{pitch 8.00 cpi}{Font Style 8.40}{Medium Weight}{Typeface 0}     MICR Part 2 : Provided by the Vendor
esc "&k15H" esc "*p907Y"     Set HMI = 15/120" Vert position = 907 Dots
esc "&a13.8C"     Move to Column 13.8
     CODE 112
esc "&f1x3x8X"     {End Macro Definition}{Call Macro}{Delete Macro ID}
esc "&f1S"     {Pop Cursor Position}     At this point, the MICR gets printed
Table 2. Escape Sequences in APLAP.prt file Explanation
Fig. 8 APXPBFEG rdf file Signature printer mask and Format Triggers
The signature piece (221) has also similar meaning.
Escape Code     Meaning     Comment
esc "&f0S"     Push Cursor Position
esc "*t300R"     300 DPI Graphics resolution
esc "*p1500X"     Horiz position = 1500 Dots
esc "*p650Y"     Vert position = 470 Dots
esc "(4B" esc "(s1p53v0s0b102T"esc "&f0S!"     Symbol SetProportionalPoint Size 53UprightMedium WeightTypeface 102Push Cursor Position!     Vendor gave the us esc "(4B"esc"(s1p53v0s0b102T!"Note: the ! when the it pushes the ! and that is where it prints the signature piece. The first part forms the symbol set , say (4B and the later part forms the signature font and ! is the piece. I took the ! from the above and let it stay with the 3rd part of it so that signature does not print twice.
esc "&f1S"      Pop Cursor Position
esc "*p+121Y"     Move down 121 Dots
esc "&f1S"     Pop Cursor Position
Table 3. Escape Sequences for Signature in APLAP.prt file and Explanation
Summary
One can print their own checks using the above steps. This can work as a cost effective solution for small organizations where the budgetary constraints are tighter. We are successful in getting the AP Checks printed using the above method.
References
Metalink Doc ID # 186640.1, Different Payment Formats â¦
Metalink Doc ID # 60936.1, Step by Step Guide to Setup a Printer in Oracle Applications
Metalink Doc ID # 250543.1, How to Create An Initialization String for a Payable Check Format
Metalink Doc ID # 48680.1, Accounts Payable FAQ â Payment Batch, Check
Metalink Doc ID # 1074792.6, Exclamation Point (!) Prints On Check When Using APXPBFEL And Cartridge
Metalink Doc ID # 158486.1, APXPBFEL Evergreen (Long Laser)
Metalink Doc ID # 146452.1, Listing of p_printer_code_mask Default Values for APXPBFEL
Chapter 2, Oracle Payables user guide
Appendix A
APLASP.prt printer codes explanation
code "200" esc "&l0o2a6d66p8.000c2e1x0l63f1H" esc "&k12.00H" esc "(8U"
esc "(s0p10.00h12.00v0s0b3T" esc "&k11.75H" esc "&a1l0R" control(M) esc"&f3005y4X"
{Portrait}
{Letter}
{6 LPI}
{Define Page Length to 66 Lines}
{Set VMI = 8.000/48"}
{Define Top Margin at 2 Lines}
{Select 1 Copies}
{Disable Perf Skip}
{Define Text Length as 63 Lines}
{Feed from Tray 1 (upper)}
0.1 esc "&k12.00H"
{Set HMI = 12.00/120"}
0.2 esc "(8U"
{Roman-8 Symbol Set}
0.3 esc "(s0p10.00h12.00v0s0b3T"
{Fixed Pitch}
{pitch 10.00 cpi}
{Point Size 12.00}
{Upright}
{Medium Weight}
{Typeface 3}
0.4 esc "&k11.75H"
{Set HMI = 11.75/120"}
0.5 esc "&a1l0R"
{Define Left Margin at Column 1}
{Move to Row 0}
control(M)
0.6 esc"&f3005y4X"
{Define Macro ID 3005}
{Enable Overlay}
code "201" esc "&f0S" esc "&a1.25r70C" esc "(8U" esc "(s1p14v0s3b4148T"
{Push Cursor Position} esc "&f0S"
1.1 esc "&a1.25r70C"
{Move to Row 1.25}
{Move to Column 70}
1.2 esc "(8U"
{Roman-8 Symbol Set}
1.3 esc "(s1p14v0s3b4148T"
{Proportional}
{Point Size 14}
{Upright}
{Bold}
{Typeface 4148}
code "202" esc "&f0S" esc "&a20.25r70C" esc "(8U" esc "(s1p14v0s3b4148T"
{Push Cursor Position}
2.1 esc "&a20.25r70C"
{Move to Row 20.25}
{Move to Column 70}
2.2 esc "(8U"
{Roman-8 Symbol Set}
2.3 esc "(s1p14v0s3b4148T"
{Proportional}
{Point Size 14}
{Upright}
{Bold}
{Typeface 4148}
code "211" esc "&f0S" esc "&f0y0X" esc "&l0E" esc "&a0L"
esc "(0Q" esc "(s0p8.00h8.40s0b0T" esc "&k15H" esc "*p907Y" esc "&a13.8C"
{Push Cursor Position}
11.1 esc "&f0y0X"
{Define Macro ID 0}
{Start Macro Definition}
11.2 esc "&l0E"
{Define Top Margin at 0 Lines}
11.3 esc "&a0L"
{Define Left Margin at Column 0}
11.4 esc "(0Q"
{0Q Symbol Set}
11.5 esc "(s0p8.00h8.40s0b0T"
{Fixed Pitch}
{pitch 8.00 cpi}
{Font Style 8.40}
{Medium Weight}
{Typeface 0}
11.6 esc "&k15H" esc "*p907Y"
{Set HMI = 15/120"}
{Vert position = 907 Dots}
11.7 esc "&a13.8C"
{Move to Column 13.8}
code "212" esc "&f1x3x8X" esc "&f1S"
{End Macro Definition}
{Call Macro}
{Delete Macro ID}
12.1 esc "&f1S"
{Pop Cursor Position}
code "221" esc "&f0S" esc "*t300R" esc "*p1500X" esc "*p470Y"
esc "(30C" esc "(4B" esc "(s1p53v0s0b102T!"
esc "&f0S!" esc "&f1S" esc "*p+121Y" esc "&f1S"
esc "&f0S"
{Push Cursor Position}
21.1 esc "*t300R"
{300 DPI Graphics resolution}
21.2 esc "*p1500X"
{Horiz position = 1500 Dots}
21.3 esc "*p470Y"
{Vert position = 470 Dots}
21.4 esc "(30C"
{30C Symbol Set}
21.5 esc "(4B"
{4B Symbol Set}
21.6 esc "(s1p53v0s0b102T!"
{Proportional}
{Point Size 53}
{Upright}
{Medium Weight}
{Typeface 102}
21.7 esc "&f0S!"
{Push Cursor Position}
21.8 esc "&f1S"
{Pop Cursor Position}
21.9 esc "*p+141Y"
{Move down 121 Dots}
21.10 esc "&f1S"
{Pop Cursor Position}
code "222" esc "&f0S" esc "*t300R" esc "*p1500X" esc "*p650Y"
esc "(30A" esc "(s0p.426h35.25v0s0b128T" esc "&f0S!"
esc "&f1S" esc "*p+141Y" esc "&f1S"
{Push Cursor Position}
22.1 esc "*t300R"
{300 DPI Graphics resolution}
22.2 esc "*p1500X"
{Horiz position = 1500 Dots}
22.3 esc "*p650Y"
{Vert position = 650 Dots}
22.4 esc "(30A
{30A Symbol Set}
22.5 esc "(s0p.426h35.25v0s0b128T"
{Fixed Pitch}
{pitch .426 cpi}
{Point Size 35.25}
{Upright}
{Medium Weight}
{Typeface 128}
22.6 esc "&f0S!"
{Push Cursor Position}
22.7 esc "&f1S"
{Pop Cursor Position}
22.8 esc "*p+141Y"
{Move down 141 Dots}
22.9 esc "&f1S"
{Pop Cursor Position}
code "241" esc "&a-100V" esc "&l5.8C" esc "(8U" esc "(s0p12.00h10.00v0s3b3T" esc "&k11.75H"
41.0 esc "&a-100V"
{Move up 100 Decipoints}
41.1 esc "&l5.8C"
{Set VMI = 5.8/48"}
41.2 esc "(8U"
{Roman-8 Symbol Set}
41.3 esc "(s0p12.00h10.00v0s3b3T"
{Fixed Pitch}
{pitch 12.00 cpi}
{Point Size 10.00}
{Upright}
{Bold}
{Typeface 3}
41.4 esc "&k11.75H"
{Set HMI = 11.75/120"}
code "299" esc "(8U" esc "(s0p10.00h12.00v0s0b3T" esc "&k11.75H" esc "&l6D"
{Roman-8 Symbol Set}
99.1 esc "(s0p10.00h12.00v0s0b3T"
{Fixed Pitch}
{pitch 10.00 cpi}
{Point Size 12.00}
{Upright}
{Medium Weight}
{Typeface 3}
99.2 esc "&k11.75H"
{Set HMI = 11.75/120"}
99.3 esc "&l6D"
{6 LPI}

Electronic signatures using password

I am currently upgrading a v5 application to 6i and want to implement some form of signature checking.
Currently the application uses OLE2 to lock the screen after 60 seconds. Entering the users password frees the screen for input.
What I would like to do is to get the user to re-enter their password as part of the key-commit trigger.
I have tried setting up a password block with a password field and button, but I would like to put something into the library that works for all forms.
Does anybody have any examples or experiances (good or bad) of this?

Whose Signature is needed on the PO ? How will this "signature" print ?
Oracle seems to support Buyer and Supplier Contact signatures.
If Supplier signature is needed , then you need I-Supplier portal for the supplier to sign electronically. The signature process in I-Supplier portal is only a userid/password screen that stores the name of the supplier.
I do see a record in the ERES for both buyer and supplier .....
but how is this to be printed on the PO itself ? Do I need to write some custom code to print this signature ?

SAP PRINT to WORD

We have a requirement from Tanzania Government,
Printing of document must be in readable format PDF/DOC which is to be processed via electronic signature device, so that all the values can be read then some digitial signature printing will be done.
We are printing all the document in printing via OTF (SAPSCRIPT), which has few LOGO's and data in tabular format with borders, so far the above said device does not support readable PDF that is been printed directly from SAP. So we need to convert the same in to word format, with all the formatting intact.
Ways to do the same,
1) Using 3'rd party PDF to word coverter which has been striked out.
2) OLE automation from SAP to WORD via mail merge
3) ??
My Question,
1 ) Can we configure any device in windows which will print documents in word, like PDF printer is configured, so that spool can be sent to such device and document can be printed.
2 ) Can we configure any device in SPAD, printer configuration, which will print documents in word, so that spool can be sent to such device and document can be printed.
3) Any Sample code would be welcomed.
4) If any one is doing the same, please let us know.
Regrads,
Dantham Conpolwedson
Edited by: Dantham Conpolwedson on Nov 15, 2010 10:32 AM

Hi,
Per my knowledge, I think:
1/ We cannot configure any device to print documents in word, instead you must use OLE to export documents to WORD manually.
2/ If you want sample of code in OLE to Word, please do a searching. I think a lot of answers appear.
It's all my opinion. Any other discussion please post.
Thanks,

Can fix the company name and signature at bottom

In some print out like 'Sales Order' & 'Purchase Order', it
always has the company name and signature prints at the
bottom of last page. If I use footer to handle this, then each
page will leave some space at the bottom. I cannot control the
company name and signature print at the bottom of last page,
it always print right after last order item printed out. Can
somebody teach me how do.
null

Kane Kan (guest) wrote:
: In some print out like 'Sales Order' & 'Purchase Order', it
: always has the company name and signature prints at the
: bottom of last page. If I use footer to handle this, then each
: page will leave some space at the bottom. I cannot control the
: company name and signature print at the bottom of last page,
: it always print right after last order item printed out. Can
: somebody teach me how do.
Kane Kan
Try using a boiler texts out of the page margin, this will help
you, try the area where it prints the page number normally
null

Inserting digitized signature in SQL plus reports

Our company has decided to use SQL plus for reporting needs. We have few reports with digitized signature printed at the bottom. Is this possible in SQL plus. Digitized signature should be in which format? Can somebody help me. If SQL plus doesn't support this, we mat need to look for alternate tools for reports.

Actually, it looks like Forums do something strange to URLs pasted into posts. Sorry!
The thread URL is Re: store/retrieve data in lang other than eng when CHARACTERSET is not UTF8

Need help with Signature on Checks using SAP SCRIPT

Hi,
I am looking for some help on how to get the Printer Resident Singature on to the Check using SAP Script. We have a HP Laser 8150 Priter in which the Chip Contains the Signature ( Printer Resident Singaure ) and currentlly the ORACLE application is able to print this signature on the checks. Right now we are in Migration to SAP and we are trying to get this Signature to print on the Check using SAP Script.
Please help us.

There are many ways to do this, the simplest way to print the signature is using HEX ENDHEX command.
1. Print the Printer font list from the printer configuration menu, Find the signature in the font list, next to it there'll be esacape sequence in ASCII and Hex format.
2. Add the following command in the window of the signature:
/: HEX TYPE PCL
/= Enter the Hex escape sequence(begins with 1B) from first step
/: ENDHEX
Regards
Sridhar

PDF form filled in Preview does not display correctly in Adobe Reader/Acrobat?

I recently received a PDF form from my bank, and filled in the fields and affixed my signature. Saved the form. The recipeint of the form opened the PDF in Acrobat or Adobe Reader and the fields don't display the filled in form, unless you click in the field. After you click out of the field, the entry disappears. When you print the form from Reader or Acrobat, the fields are blank, but the signature prints.
Before saving the form from Preview, the fields appear normally in Reader/Acrobat.
Running Lion 10.7 and Preview 5.5.
Anyone else have this happen?

I've since found out that there is somewhat of a "fix" that addresses a way to see the form entries in Acrobat, but doesn't resolve the problem the Preview creates. There is a script available on the Adobe forum that can be installed into Adobe Acrobat: http://blogs.adobe.com/pdfdevjunkie/2009/11/script_to_fix_mac_osx_previewa.html. The link and also explains the problem which should really be addressed by Apple. After installation, it will appear in the Edit menu of Acrobat. Once you open a Preview form, selecting "Fix Field Appearances" will repair the form so that the entries are visible.
Preview will still create bad forms, but this script will allow them to be visible in Acrobat. Unfortunately if you're sending a form to someone, there's no way to know if the recipient is using Preview or Acrobat and whether they even know about the problem. So you would have to create the form in Preview, open it in Acrobat, fix the field appearances and re-save. So it's not really a fix, just a work-around. Still don't use Preview for this reason.
I don't know if the script works with Adobe Reader, there's no mention that it does or doesn't in the forum entry.

Signature Printing

Similar Messages

Maybe you are looking for