Silent Monitor and Call record with voice vlan

We are pretty new to CCX, and want to get silent monitor and call recording working. I've read a bunch of troubleshooting docs, and a bunch of the discussions here, but I am still unable to get it to work the way that I want.
Heres the setup. The phones are all set to the recommended settings, and the agent pc is plugged into the phone. The data vlan is 111 and the voice vlan is 222. When I run the nicq prog on the agent pc, it can not find the phone, but I can enter the ip in , and it sees the phone. The supervisor laptop can not monitor or record.
If I change the voice vlan to 111, nicq still can not find the phone, but the supervisor can record and monitor with no problem. Is is an issue with 802.1q and perhaps my nics do not support it?
CCX Ver:
8.5.1.11004-25

Hi
It could be, but it's pretty rare.
Have you enabled 'PC Port Voice VLAN Access' and 'SPAN to PC Port' on the phone?
Have you tried alternate PCs/laptops on the back of that phone?
Aaron

Similar Messages

How to append calling and called number with translation rules?

Hello,
I have one question about digit manipulations.
How to append calling number and called number with IOS commands?
For example, when 123 dials 45678, translations have to be performed and the new called number to be 12345678.
Thank you,
I will vote this conversation.

It is not possible with translation rules.
However, you can do that with a TCL/IVR script.

Cat 3750 with Voice VLAN and Dynamic VLANs

Morning,
Has anyone had any success with configuring a Catalyst 3750 with a Voice VLAN (Cisco phones) and 802.1x dynamic VLANs?
Is a RADIUS server able to provide values to change the native vlan?
Is there a decent tech note knocking about for configuring 'dynamic VLAN assignment through MAC addresses'?
Thanks,

Voice VLAN's don't require trunk ports to be configured (unless you are talkling about 2900XL/3500XL switches). Cisco added the ability to trunk a single 802.1q VLAN down an access port in addition to the access vlan - so in 2950 or above the only config you need is:
interface FastEthernet0/1
switchport
switchport mode access
switchport access vlan 10
switchport voice vlan 100
This is effectively the same as:
interface FastEthernet0/1
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allowed vlan 10,100
The only difference is the CDP message with the first config will advertise the Voice VLAN capability and the tag.
With the older 2900XL/3500XL switches you had to configure the interfaces like the second example (plus adding the command switchport voice vlan xx for CDP to inform the IP Phone of the voice vlan).
QoS is not detailed anywhere here and that obviously plays an important role with voice.
In your scenario I am not sure ACS can do what you describe as this will require 802.1x supplicants on the client PC's (I may be wrong here and I do remember someone talking about switches being able to do an 802.1x 'proxy' using the MAC address on behalf of non 802.1x capable devices). This seems to me more of a VMPS application.
Personally I would reconfigure the network each time and charge the occupants a small fee for network setup.....
HTH
Andy

Ask the Expert : Call Recording with Cisco Unified Communication Manager (UCM)

Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco Unified CM call recording solution that provides the ability to record customer conversations for compliance purpose. This topic will cover an overview, configuration and troubleshooting of the call recording feature.
Monday, January 19th, 2015 to Friday, January 30th, 2015
Harmit Singh is a technical leader with the High Touch Technical Services (HTTS) and Technical Assistance Center (TAC) Unified Communications teams based in Bangalore. He has broad experience in Cisco Unified Communications infrastructure solutions. He has 10 years of experience working with large enterprise and service provider networks. He also holds CCIE certifications (#20012) in Voice and Collaboration as well as Red Hat and VMware certifications.
Mohammed Noorulla Khan is a customer support engineer in High-Touch Technical Services (HTTS) Unified Communications teams based in Bangalore. His areas of expertise include Cisco Unified Communications Manager, Gateways, and Jabber. He has over 6 years of industry experience working with large enterprise and service provider networks. He also holds CCIE certifications (#35741) in Voice and VMware certifications.
** Remember to use the rating system to let Mohammed and Harmit know if you've received an adequate response. **
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Collaboration, Voice and Video community, subcommunity, IP Telephony, shortly after the event. This event lasts through January 30th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hi Maheshwar,
Thank you for your query. Please find my response below:
1> Do we support recording with HCS environment and which 3rd party vendors are validated with HCS based call control 10.1.1?
Answer: Whether you use a standalone UCM cluster, UCCE or HCS, call recording would be supported across the board in the same manner.
Please refer to the following link:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/hcs-cc/10_0_1/Install_and_Config/CHCS_BK_ICC270D0_00_installing-and-configuring-cisco-hcs/CHCS_BK_ICC270D0_00_installing-and-configuring-cisco-hcs_chapter_011.html#CHCS_RF_T1105284_00
Option
Notes
Recording
All Recording applications that are supported by Unified CCE are supported on HCS for CC. For details, see Recording section in Agent and Supervisor Capabilities.
With respect to which 3rd party vendors have been validated, marketplace.cisco.com is a good place to crosscheck this info. You will find a Cisco Compatible Logo against the partners listed there. The logo is used to signify that the PARTNER product has undergone technical interoperability testing with the Cisco product specified. The interoperability testing is conducted by a third party laboratory based on testing criteria set forth by Cisco. PARTNER is solely responsible for the support and warranty of its product. Placement of the PARTNER product or information pertaining thereto, on the Cisco Marketplace website does not constitute an offer to sell the PARTNER product in any way. For further information on the PARTNER products, please visit the PARTNER company website.
Please refer to the following link and use the search field under Collaboration Technology:
https://marketplace.cisco.com/catalog/search?utf8=%E2%9C%93&search[q]=&search[technology_category_ids]=23%2C24%2C197%2C1940%2C1941%2C1921%2C1576%2C1897%2C1983%2C2418%2C26%2C198%2C1904&search[order]=tier&per_page=20&_=1421663854257&ts=1421663855441
2> Which end points are supported for recording via HCS call control?
Answer: The following link should help clarify this:
http://solutionpartner.cisco.com/web/sip/wiki/-/wiki/Main/Unified+CM+Silent+Monitoring+Recording+Supported+Device+Matrix
Please let us know if you have any follow up questions. Hope this is helpful.
Regards,
Harmit Singh.

Lync 2010/2013 - Call Recording with PSTN

I am trying to find out more information about how larger companies use Lync while still recording calls to and from the PSTN. We have a huge need to be able to record specific (not all) calls in an on-demand fashion from the Lync client.
Lync seems to have some strange limitations with what it lets you record.
My issue is that Lync doesn't present options for recording calls to the PSTN unless you convert the call into a conference using some creative "tricks". Has anyone found a better way of doing this so that the user can just select record? It seems
extremely counter productive to say "hey here's our unified product", but if you need this really basic feature of a phone system you need a third party product. None of the third party products I've looked at actually integrate with Lync
in a way that the user just clicks record or some other option.
This is a major limitation of Lync for us and it is really holding up our ability to adopt Microsoft Lync. Does anyone have some good guidance on the best way to do PSTN recording with the Lync client?

Hi,Shaddie,
Yes,Lync doesn't support PSTN call except in a conferencing call,peer-to-peer call recording only works between Lync clients,and if someone call you via PSTN the call recording will not work, check the following links to have a workaround.
http://windowspbx.blogspot.com/2012/05/lync-user-tip-20-how-to-record-lync-to.html
http://blogs.perficient.com/microsoft/2011/02/call-recording-in-lync-2010-pstn-oddity/
Regards,
Sharon
Sharon Shen
TechNet Community Support
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question.

Quality and Agent Recording with CCOD

When I run the storage report for Call Center on Demand, it reports Quality Recording Duration and Agent Recording Duration. What's the difference? I have over 3 times as much in Quality Recording as I do in Agent Recording. I'd love to keep the conversations our agents have, but I think Quality is recording more than that -- parts of the call I don't need. Any suggestions?

The agent recording are exactly what they sound like. These are recordings that are created when an agent hits the record button during a call. The quality recordings can be made one of two ways. The first way is by a supervisior manually selecting to record an agent i.e. I suspect agent John Doe is not following company procedure so I select his name from the supervisor and I hit the record button. The other method is if the Administrator selects to record a certain percentage of each agents calls the system will automatically record calls according to the threashold set up by the Administrator. i.e. If the Administrator chooses to record 5% of am agents calls that means that the system will automatically create a quality control recording for every 20th call. If the Administrator selected 10% than 1 in 10 calls would be recorded. This is set up in the Administration Manager on a per agent basis. If you want to have fewer quality control recordings then the percentage should be lowered or you can disable automatic recording of agent so that no recordings are automatically created. This will not prevent agents or supervisors from manually creating recordings.

Television and TV Recording with a ATI Radeon X1900 XT 512MB equip Mac Pro

I have been looking into a Mac Pro 2.66-3.0 Dual-core equipped with a ATI Radeon X1900 XT 512MB. One of the things I would like to accomplish is to also use the thing as a television and TV recorder (reliably). I have experience with the a PC equiped with a ATI9700pro all in wonder. I had nothing but problems with the software with hours (weeks) spent trying solve the issues. Turns out this is not an unusual thing with the ATI-Allinwonder. Thought I would check here to see whether anyone has input on how the x1900 works on the mac pro esp as a tv device.

the elgato system is an external tv tuner that connects by USB. It has nothing to do with the graphics card in your mac.
you can connect an antenna, cable, s-video or composite. Some of the models accomodate HDtv now.
the results are clean, and i've had no problems.

Click 2 Call and Call Recording Apps for Surface R...

I think I know the answer to this, but it doesn't appear that Click to Call is a feature that is available for those of us on Surface RT. Additionally, I can't find any of the call recording apps available through the skype site. Anyone have any input on this?

Hi and welcome to the Skype Community,
1. Unfortunately "Click to call" is not available on Safari for iPad because the Safari Web Browser in iOS does not support the concept of plug-ins (like Safari on Mac does). That means Skype cannot hook into the browser to extend the functionality.
2. Just so I understand you correctly: You want phone numbers in Emails highlighted in the desktop application "Outlook 2013" as well, correct?
Follow the latest Skype Community News
↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

PVLANS used with Voice VLAN's

Hi,
I am working on a LAN Design that incorporates both Voice and Data and wondered if it is possible to have a switchport configured to be private VLAN and have a Voice VLAN configured as well
Thanks

No, according to the configuration guide on Private vlans:
Do not configure private VLAN ports on interfaces configured for these other features:
?Port Aggregation Protocol (PAgP)
?Link Aggregation Control Protocol (LACP)
?Voice VLAN
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/122sx/swcg/pvlans.htm
Please rate all posts.

Dot1x with voice vlan

Hi guys,
recently i have configured the dot1x security feature on the cisco c3650x switches with IOS 15.2(1)E. But when I added voice vlan to the port, the ip phone can't register.
My switch port configuration as below:
interface GigabitEthernet0/47
switchport mode access
switchport voice vlan 60
switchport port-security maximum 2
switchport port-security
switchport port-security aging time 1
switchport port-security violation restrict
switchport port-security aging type inactivity
switchport port-security mac-address sticky
srr-queue bandwidth share 10 10 60 20
queue-set 2
priority-queue out
authentication event fail action authorize vlan 203
authentication event no-response action authorize vlan 203
authentication host-mode multi-host
authentication port-control auto
mls qos trust device cisco-phone
mls qos trust cos
macro description USER
dot1x pae authenticator
auto qos voip cisco-phone
spanning-tree portfast
spanning-tree bpduguard enable
service-policy input AutoQoS-Police-CiscoPhone
Guys, please advice is there any other feature shuld be activated on swith to resolve this issue? i done all configuration on guidance of cisco documents.
BR
Rashad

duplicate post: https://supportforums.cisco.com/thread/2248853?tstart=0
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Both Monitor and TV use with 1 adapter?

I have a 13" MacBook. I also have a nice 19" Samsung flat screen monitor lying around here. Since my laptop sees most of its duty on a table during the summer (no school), I'm thinking of getting the monitor and a keyboard and hooking it up, even though it's enormous.
Now, I know all I need is a Mini-DVI to VGA connector (apple sells it for $19).
But the thing is, I'd like to also be able to connect my laptop to a TV (meaning I need the mini-DVI to Video connector, $19 again).
I could buy both, but I don't want to spend $40 on just connectors. What's my best option? Is there any other way?

Some TVs have VGA connectors on them, but I'm guessing yours does not. In that case, I think you are stuck buying two adapters.

VGA monitor and TV switchbox with Mini

I have recently purchased the EyeTV for DTT box for my Mac Mini. I currently use a Dell VGA monitor for my work but would like to watch TV broadcasts from the EyeTV through my TV. However, I don't want to keep unplugging the monitor and then plugging in the TV (via the DVI - S-video adaptor) each time I want to view EyeTV stuff. Is there some kind of switchbox available which would enable me to have both the monitor and TV connected and where I could just flick a switch to send the video signal to either the monitor or TV (note: I don't need the video signal to be displayed on both the monitor and TV at the same time).
Thanks in anticipation.

Sorry I misread your post.
One option would be an eyeHome which would connect to the ethernet port of the Mac mini.
Another option is a VGA Splitter.

How many min. can i record with voice record with MuVo V200 1

Hi,
I'm going to buy the Creative MuVo V200 GB.
Now my questions about this player.
How many minutes can i record over voice recording.
Maybe someone can tell me how much Megabytes minute of recording will take.
Are there different quality levels of recording?
In which format does the player save the recordings?
I will use the player to record lectures at the uni'versity.
Did anyone have done this?

Silent monitoring and recording

When a supervisor or agent presses the record button they get an error "error received from recording service. More information in log file". I have attached the log file, anyone have this before?

Have you tried doing a resync? That option is also under CDA. When you expand Service Configuration, you will see Synchronize Directory Services as an option. Try resyncing and see if that resolves the issue.

LG Ally: Sound only works (media and calls namely) with headphones. (Solution)

I recently had a problem with my phone that was driving me crazy for the past few days.
The problem in particular was:
When i would answer phone calls, i would hear nothing on the other side of the call. In addition i was unable to watch Youtube videos and listen to the sound on the phone's speakers. Even more peculiar was that i would hear my ringtones and notification sounds, which i could also listen to when playing the sounds for fun.
Now it seems like its a fairly common problem for those who have the same kind of phone that i do, so i dabbled in the number of solutions:
- restarting my phone
-turning my phone off and taking out the battery for 30 seconds (which i did, but left the battery out for much longer than specified)
-restored factory settings (which erased a lot of apps and what not in the process)
Note that im only stating all this just to clear up what the problem was and what i tried to do to fix it. and i actually found the solution on this site:
http://androidforums.com/lg-ally/112076-interesting-problem-no-media-volume.html
If you don't care to skim through the posts the solution is this:
The Headphone Jack is (most likely) dirty/dusty/etc. The cleaning formula Pro Gold/De-oxit is recommended, but i found that thinning out a Q-tip so that it can fit in to the jack, then spinning it around inside helps just as well. There was a noticable amount of dirt, and once removed i tried the music app on my phone without headphones only to have it play music again. (Also: I blew into the headphone jack as well. I figured it might have been dirty and from someone who used to play the NES, this is a very common practice.)
Anyway i hope this helps out anyone with this problem in the future. So try to find this before you return your phone and/or restore factory settings.

Good post! I had a problem similar to this a while back with my Eris where the headphone icon would stay in the notification bar. I had to use basically the same solution (I think I used a toothpick, though a Q-Tip is probably safer). I do find it funny that you blew into the hole, as I did the same thing, also being a former NES player. Why did that always work?!?

Silent Monitor and Call record with voice vlan

Similar Messages

Maybe you are looking for