Sim Not Provisioned after doing iOS6 update

I recently restored my iPhone 3GS to factory settings and updated my phone to iOS6. All my data/apps/etc came over just fine after syncing but now my phone shows No Service and 'SIM Not Provisioned' when I went into Settings > General > About > Network. It was working normally previously. Data/3G was working just fine. Not sure If I need to contact AT&T to get them to adjust some account settings or verify somehow but it's odd that It'd do that after the update when I had done nothing different with the phone. I've gone though the standard troubleshooting (restarting, removing sim & reinserting, resetting network settings,etc) Any help/insite/suggestions would be appreciated.

It's possible the SIM failed during the update. It's not common, but it's not unheard of. Stop in an AT&T store and get a replacement SIM.

Similar Messages

My phone says SIM not valid after ios 5 update, Why and how do I fix it?

Why does my iPhone 4 say SIM not valid after I updated to ios 5? Also, is there anything I can do to fix it?

Sounds like your phone was software unlocked, or hacked/jailbroken, to work with any carrier. Updating the phone restored the original carrier lock. All you can do now is contact the carrier it is locked to and see if they have an unlocking policy.
Good luck.

Ipad not working after doing an update.

Can anyone help please. My mum has managed to scramble her ipad. She got a prompt to do an update and got the following at various times. (Please not this is all received on a frantic phone call so rather garbled)
Ios6 configurare and stuff in different languages
Then Update completed
3 bars
Just a few more steps and you're finished
And finally
Setup incomplete , Continue , Wi if settings , Start again - she's tried switching it off and back on again but it's not working.
Any ideas? Unfortunately, I told her you can't break an ipad. Looks like I lied.

Well she rang this morning to tell me that she pressed the 'continue' option and it is now Ok. Phew!

Flash player not working after doing the update

I got an update on facebook saying that I needed to update my flash player. so I did, and now it keep saying that I need to update when It already shows that it is the updated version. now I cannot do anything that involves using flash, no facebook or online games or utube. please anyone if you can help me figure this out.

Recently, my games on Facebook and Youtube stopped working and prompted me to upgrade my flash player.
It included the link to Adobe, as do all the sites that require it.
So, I did. It says install successful, but it is not.
I use Safari on a Mac 10.5.8.
The flash player is still working on FireFox.
I tried many things so far and it is still down on Safari.
I tried upgrading from the internet.
I tried rebooting a flash player from my Creative Suite 4... that actually told me my disc 2 was blank during install!
I uninstalled flash player and reinstalled many times. No go.
I uninstalled my Flash program and nearly lost it!!
It would not reinstall from my CS4 discs.
A friend helped me and I am pretty sure the Flash maker is up again. I see the icons are back in place in the applications folder, but i did not try running it yet.
He thought the flash player was working again when he returned my computer, but it is still not working in Safari.
I tried downloading and reinstalling the flash player again from Adobe, yes..the correct version for Intel based Mac.
He ran first aid repair a few times.
There was a lot of things that got fixed.
I am in need of more help.
anyone figure this out?
please!

My mac book pro does not boot up correctly anymore after doing some updates. I did have my ipod charging to my mac book. I ran the simple updates and never go to the maverick update and now my computer will not boot correctly. Help!

Please help my computer is not repsonding after doing some simple updates. I follow the instructions and which is simply click for the update to take place. I did what I was instructed to do. I did not do the new update for the Mavericks yet. I just did simple updates. The computer shutted down and restarted but would never get pass the grey screen with the spinning wheel and the booting bar that would not go past a certain point befor shutting off again. The computer is practically brand new. I purchased the computer from best by 2012 and the warrenty just ended the past October. I hardly use the computer maybe 4 times since I have had it because I have another main computer that I uses. However, I don't want to do a hard rest becuase I do have the entire adobe suits software that I paid for and don't want to loose. I have an appointment with apple today to see what they say but I hope that my computer that I hardly every use is not defected after doing a updated pushed by Apple. Any thoughts or suggestions???? Thanks in advance Apple Family :-)

Well, I was at Apple for sometime on that day. I got a Genius that did not want to work. She basically jumped to the money to tell me that my hard drive was no good and that I was out of warranty (October 2013). I began to explain to her that I had only used the computer 5 times and that I don't use this computer as my main computer because I also have a Toshiba that is less expensive that I have had for several years and not one issue out of it. The rep told me that I could by a new hard drive for $161.00 and that I would loose all of my software and photos that I have on this computer. However, I told her that it's bazaar that it happens right after my warranty goes out and had I used it more often when in warranty before October then I would have been covered. Keeping in mind that I would still be very disappointed with the product because I would loose all of my information and it would not make sense to me why the hard drive fails on a very gently used computer. So I asked for a manager and it took her some time to get one. In the mean time I watched how the other Geniuses interacted with the other customers and seen that they were very engaging with convo and very help. I guess I just I got another lemon when I got my rep. When the manager finally came. I went from A-Z with the issues and that I felt that something could or should be done because the rep said that she did tests on my machine and it read to her that my hard drive was bad and there was nothing that could be done. I explained that I was not looking forward to paying for services to have my new computer repaired. The manager offered to give me 25% off the cost but I still didn't feel that it was effective. After he left and the rep wrote the notes in the system, I told her that I didn't think that all options had been exhausted and that there was something else that could be done. I told her to erase the machine and see if the updates could be installed and if the system would continue to do the same thing. The rep was hesitant and said that I would loose everything which we already know that we were at conclusion from the beginning. She assured me that I would happen again and that I would need a new hard drive. I just told her to erase the machine and get me another manager because I was just getting tired of her unhelpfulness and negative perspective. The new manager came and was very pleasant and I explained everything once again from A-Z. I informed him that I had the machine erased and that I need his help with options because I don't feel that the rep or the last manager was resourceful or helpful. He apologies for the actions of the reps and proceed to tell me that they will run all the updates in the store and that if it booted correctly that I should continue to use the machine with out adding the adobe software back on just incase that it crashes again and I'm out of money once again. However, if it does happen again and it is a hard drive issues that he would work with me to resolve the issues. As my computer went through the process of rebooting from out of the box stage another rep approached me because he could tell that I was upset and not happy. I told he what had happen and he said I think I can help you a little more. He said that I just want to run further testing on you computer for different components to make sure that everything would work properly and pin point any issues. I was delighted with that option. Anything would help at this time especially someone who is willing to help. The first test that he ran was to for the hard drive and he said that since it failed the test the first time could be because the software update glitch and did update correctly which would make the test faulty and be negative. As I sit with finger crossed the test came back as a pass test that my hard drive was not the issue and that the update was the cause and that I did not have to buy a new hard drive. I was happy that the computer was ok but I lost information. All of the updates were done in the store and everything works fine now. If I was not persistent about my gut feeling then I would had left out thinking that I had to pay for a new hard drive that I really didn't needed. Now I can invest that money in a external hard drive to start backing up my information. Lesson learned by I'm still on the fence about things but I hope all is well. I really went through a lot. No help or no service was not an option that I was taken. I hope that it helps.

My iPad2 is not working after an unsuccessful update to the new iOS6. How do I get working?

My iPad2 is not working after an unsuccessful update to the new iOS6. How do I get working?

- Try resetting the iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Download/install a new app
- Restore from backup
- Restore to factory daults/new iPod.

Just yesterday I downloaded the newest update for iTunes, a few days before doing this I purchased music, but after doing the update my songs will not play. It shows a message that says this file cannot be located, what can I do to find the location?

Just yesterday I downloaded the newest update for iTunes, a few days before doing this I purchased music, but after doing the update my songs will not play. It shows a message that says this file cannot be located, what can I do to find the location?

The path C:\users\owner\appdata\local\apple\apple software update\bonjour64.msi cannot be found. verify that you have access to this location and try again or try to find the installation package "bonjour64.msi" in a folder from which you can install the product bonjour.
Unfortunately, this sort of trouble has gotten more complicated to deal with ever since Microsoft pulled the Windows Installer CleanUp utility from their Download Center on 25 June 2010. First we have to find a copy of the utility.
Let's try Googling. (Best not to use Bing, I think.) Look for a working download site for at least version 3.0 of the Windows Installer CleanUp utility. (The results from mydigitallife and Major Geeks are worth checking.)
After downloading the utility installer file (msicuu2.exe), scan the file for malware, just in case. (I use the free version of Malwarebytes AntiMalware to do single-file scans for that.)
If the file is clean, to install the utility, doubleclick the msicuu2.exe file you've downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any Bonjour entries and click "Remove".
Quit out of CleanUp. Restart the PC, and try another iTunes install. Does it go through properly this time?

I am having trouble getting 3G service on my new ipad 2, what does it mean when it says SIM not provisioned?

I am having trouble accessing the 3G network on my new ipad 2, what does it mean when it says that the SIM is not provisioned?

SIM not provisioned usually means that the 3G service has not been set up yet. Have you set up the service through the settings menu?

I have a new iphone 4 but have a problem in that the network reads Sim not provisioned, please advise how to overcome this problem?

My new iphone has been recognised by itunes, updated the software but unable to connect to a network, on checking "Network" the phone is searching but to no avail. In "About, Network, there is a statement reading SIM not provisioned". I have no idea what this refers to perhaps someone could advise?

I've managed to speak to someone who knew what he was talking about and having confirmed the original sim on my iPhone 3 followed by confirming the number on the iPhone 4 Micro Sim he advised that the new micro sim had not been activated. As a direct result we'll head off to one of their support offices to activate and hopefully pass on the iphone 3 to another of our employees after a reset of course!

Problem getting correct data from MS Access after doing an Update

Hi all,
I have a problem getting correct data after doing an update. This is the scenario
I am selecting some(Eg: All records where Column X = �7� ) records and update a column with a particular value (SET Column X = �c� ) in all these records by going through a while loop. In the while loop I add these records to a vector too, and pass it as the return value.
After getting this return value I go through a for loop and get each record one by one from the DB and check if my previous update has actually happened. Since No errors were caught while updating DB, I assume all records are updated properly but my record set shows one after another as if it has not been updated. But if I open the DB it is actually updated.
This does not happen to all records, always it shows like this
1st record     Mode = �c�
2nd record     Mode = �7�
3st record     Mode = �c�
4nd record     Mode = �7�
9th record     Mode = �c�
10th record     Mode = �7�
I am relatively new to java and this is someone elses code that I have to modify,So I am not sure if there some thing wrong in the code too
//Here is the method that gets records and call to update and add to vector
public static Vector getCanceledWorkOrders() throws CSDDBException{
//Variable declaration
try {
    objDBConn = DBHandler.getCSDBCon();
    strSQL = "SELECT bal bla WHERE [Detailed Mode])=?)";
    objStmt = objDBConn.prepareStatement(strSQL);
    objStmt.setString(1, '7');
    objWOPRs = objStmt.executeQuery();
    while (objWOPRs.next()) {
     //Add elements to a vector by getting from result set
      //updating each record as PROCESSING_CANCELLED_WO(c)
      iRetVal = WorkOrderDetailingPolicy.updateRecordStatus(objPWODP.iWorkOrderNumber, objPWODP.strPersonInformed, EMSConstants.PROCESSING_CANCELLED_WO);
      if (iRetVal == -1) {
        throw new NewException("Updating failed");
catch (Exception e) {
    vecWONumbers = null;
    throw new CSDDBException(e.getMessage());
}finally{
    try {
      objWOPRs.close();
      objStmt.close();
      DBHandler.releaseCSDBCon(objDBConn);
    catch (Exception ex) {}
//return vector
//here is the code that actually updates the records
public static int updateRecordStatus(int iWONumber, String strPerInformed , String strStatus) throws CSDDBException{
   PreparedStatement objStmt = null;
   Connection objDBConn = null;
   String strSQL = null;
   int iRetVal = -1;
   try{
     objDBConn = DBHandler.getCSDBCon();
     objDBConn.setAutoCommit(false);
     strSQL = "UPDATE Table SET [Detailed Mode] = ? WHERE bla bla";
     objStmt = objDBConn.prepareStatement(strSQL);
     objStmt.setString(1, strStatus);
     objStmt.execute();
     objDBConn.commit();
     iRetVal = 1;
   }catch(Exception e){
     iRetVal = -1;
   }finally{
     try{
       objStmt.close();
       DBHandler.releaseCSDBCon(objDBConn);
     }catch(Exception ex){}
   return iRetVal;
//Here is the code that call the records again
public static WorkOrderDetailingPolicy getWorkOrders(int iWorkOrderNo) throws CSDDBException{
    Connection objDBConn = null;
    PreparedStatement objStmt = null;
    ResultSet objWOPRs = null;
    WorkOrderDetailingPolicy objPWODP = null;
    String strSQL = null;
    try {
      objDBConn = DBHandler.getCSDBCon();
      strSQL = "SELECT * FROM [Work Order Detailing] WHERE [Work Order No] = ?";
      objStmt = objDBConn.prepareStatement(strSQL);
      objStmt.setInt(1, iWorkOrderNo);
       objWOPRs = objStmt.executeQuery();
      if (objWOPRs.next()) {
        objPWODP = new WorkOrderDetailingPolicy();
        objPWODP.iWorkOrderNumber = objWOPRs.getInt("Work Order No");
        //......Get Record values
    catch (Exception e) {
      objPWODP = null;
      throw new CSDDBException(e.getMessage());
    }finally{
      try {
        objWOPRs.close();
        objStmt.close();
        DBHandler.releaseCSDBCon(objDBConn);
      catch (Exception ex) {}
    return objPWODP;
}

Hello,
Can you put an example of your problem online?
Are you sure you're not having problems with case sensitive data?
Thanks,
Dimitri

My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError P1 : c000009c P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError P1 : c000009c P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

Iphone 4 not recognized and will not sync after latest itunes update. I have done all trouble shooting and uninstalled and reinstalled itunes to no avail.

iphone 4 not recognized and will not sync after latest itunes update. I have done recommendedl trouble shooting and uninstalled and reinstalled itunes to no avail. Can I go back to earlier version of itunes or restore computer to fix?

'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

Cellular - Suddenly "No Service" and "SIM not provisioned" iPad 2 and mini

I have an iPad 2 and an iPad mini and occasionally sign up for AT&T cellular service on both, has always worked and never had a problem, until now!
Suddenly on BOTH iPads I see "No Service" and if I check network in settings I see "SIM not provisioned"?
My question is, does anybody know what has happened, especially as it has happened to both of my iPads, what it means and how I can resolve it?
I was reluctant to post as I see lots of similar posts on line, but couldn't anywhere find a solution.

Talk to your carrier, it's their sim problem.

SIM not provisioned on IPAD

I have not been able to access a network since I purchased my IPAD. Can't seem to find someone at AT&T nor apple care that know how to fix this problem either. I get the error message USIM9992 when I try to active a data plan both online and on the IPAD itself. When you look under the general network settings on the IPAD the message "SIM not provisioned" appears. Does anyone have any suggestions on how I can get my IPAD to connect via the AT&T network?

I would, in order:
- Reset network setting:
Settings>General>Reset Network Setting
- Reset iPad:
Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Remove and reinstall the uSIM
- Lastly go to an AT&T Store. Yu may have a defective uSIM.

TS1702 After doing an update on tribez everything has disappeared ...... Anyone else have the same problem??

HAs anyone else had the same problem, after doing an update nothing will come up for tribez just a blank screen. My late nights are not the same now!!!

Your Performance preferences screen capture reveals you have a single hard drive with little available space to accommodate both the Photoshop scratch file and the swap files of the OS.
It's obvious that Bridge finds itself at times with insufficient space to build its cache.
However, it's unclear why that should affect only DNG files and not other type of image files. Puzzling, unless the DNG files are the only large image files you have.
Parts of the following may illustrate what happens when the scratch file is on your boot drive:
The rule of thumb I follow to figure out scratch space says to figure on 50 to 100 times the size of your largest file ever multiplied by the number of files you have open. I have seen the scratch file exceed 800 GB once, an admittedly rare occurrence, but it often exceeds 200 GB when stitching large panoramas and the like.
As an example—and stressing that I'm aware that others have even more scratch space than I do—I keep two dedicated, physically separate hard drives as my primary and secondary Photoshop scratch disks and a lot of GB free on my boot drive for the OS. I also have 16 GB of RAM installed.
Additionally, if you only have a single HD, i.e. your boot drive, you'd need it to be large enough to accommodate both the swap files of the OS as well as Photoshop's scratch.

Sim Not Provisioned after doing iOS6 update

Similar Messages

Maybe you are looking for