SIM not reading, Need help fast due to being abroad!!
My iPhone 4 was working perfectly until about an hour ago when I received an error message stating I have no sim. I restarted the phone several times with no luck. Then I restored all settings through the iPhone with no luck until I turned my phone off for 3 mintues and upon turning it back on (I was unable to reset the phone because I have no computer back up and no WiFi because of the no SIM) the tmobile signal appeared. I was able to connect to wifi to reset my phone which it is in the processes of doing. But after 5 minutes the NO SIM appeared where tmobile appeared. I am in Austria for another 3 weeks and this is my only connection back to home and I am not even able to contact someone to tell them what is happening. If anyone has ANY solutions that does not involve going to an ATT store (my phones original carrier) to replace the SIM card since I am not capable to do so it would be greatly appreciated. Thank you so much for your time
Scarlett
Try this (copied from http://support.apple.com/kb/TS2802):
Remove the SIM card.
Verify that the SIM card is not damaged or dirty, then reinstall the SIM card.
Try turning iPhone off and then on again.
Wait approximately two minutes, then see if iPhone detects the SIM card and if it will register on the network.
If that doesn't work, try another SIM card for that carrier, if possible, to see if it is detected.
If the message still exists, please go to: apple.com/support/iphone/service/faq/ for information on service.
Note: If you need to send your iPhone in for service or if you want to temporarily use a different phone, you may be able to use the SIM card inside your iPhone with another GSM phone.
Similar Messages
-
Will not start need help fast as f
Have tried to delete the entire program and downloaded it again does not help need help immediately, shell have done a movie.
it came suddenly and was okay, but thank you for your help
-
my ipad device does not come up on itunes, need help fast:/, my ipad device does not come up on itunes, need help fast:/
Hi, Nancy.
Thank you for visiting Apple Support Communities.
Here are the steps that I would recommend going through when experiencing an error that begins with 0xE.
iOS: Unknown error containing '0xE' when connecting to a Windows PC
http://support.apple.com/kb/ts3221
Cheers,
Jason H. -
My daughter has spitefully changed my password and has refused to tell me. I have so much medical information that I can not lose. Is there anyway to get around this problem. Please I need Help fast.
Connect the iPod to your syncing computer and restore it via iTunes. However, if iTunes asks for the unknown passcode you need to place the iPod in recovery mode and then restore the iPod from backup. For recovey mode see:
iPhone and iPod touch: Unable to update or restore
"If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone and iPod touch software."
Above is from:
http://support.apple.com/kb/ht1212 -
i want the 200 mb plan for my iphone and wanted to know if instead of using safari i can use apps such as facebook or tumblr without using up my data. i got the asnwer that i can avoid that by using wi-fi, but how does that whole thing work?
sorry i am a bit new at this, and i need help fast!
THANK YOU!hookedonlerman wrote:
but will that replace the use of using up data? (wifi & 3G)
It sounds as if you don't really understand what "using data" means. Data is not something different from WiFi and 3G, it's something sent over WiFi and 3G. Think of data as water and WiFi and 3G as types of pipes. Some apps need to send and receive data to work. That data can be sent or received in different ways. It can be sent over WiFi or 3G. Both official iPhone carriers in the U.S. have metered data plans. It's sounds as if you're talking about AT&T's 200 mb data plan. WiFi is not provided by your cellular carrier. You can have WiFi from your Internet Service Provider at home or you can access free WiFi at places like McDonalds or Starbucks or paid WiFi at places like airports.
If you have WiFi turned on on your phone and WiFi is available, the phone will default to WiFi. WiFi is faster than 3G and generally not metered, and is sometimes even free. If you are out of range of WiFi, you would be using 3G to send and receive your data. With a metered plan, you need to keep an eye on how much you are using because if you go over your allowance, you will be charged additional fees. -
Why does this code not do what I want to happen?
I have a 7 non functional buttons above the buttons for the days in the month and I would like to be able to layout the buttons starting on the day that the month begins and ending where it ends.
Like in the microsoft windows calander.
Any ideas as to how I'd do this?
I need help fast. Please.
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.io.*;
import java.util.*;
public class MyDairy extends JFrame
//Initilises Global Variables
myHandler H = new myHandler();
monthHandler J = new monthHandler();
openHandler O = new openHandler();
String monthName;
JComboBox months;
static String[] daysOfWeek = {"Sun", "Mon", "Tue", "Wed", "Thur", "Fri", "Sat"};
static int[] daysInMonth = {31, 28, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31};
JFileChooser box;
public MyDairy()
//Initilises the JComponents
JMenuBar menuBar;
JMenu menu;
JMenuItem menuOpen;
JMenuItem menuSave;
JMenuItem menuExit;
JButton dayName[] = new JButton[7];
JButton day[] = new JButton[36];
JPanel b;
JPanel a;
Calendar today = Calendar.getInstance();
Calendar startOfMonth = Calendar.getInstance();
startOfMonth.set(Calendar.DAY_OF_MONTH,1);
startOfMonth.set(Calendar.DAY_OF_WEEK,7);
System.out.print(startOfMonth);
//Sets up the Layout
setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
Container c = getContentPane();
c.setLayout(new BoxLayout(c, BoxLayout.Y_AXIS));
a = new JPanel();
a.setLayout(new GridLayout(0, 7));
b = new JPanel();
b.setLayout(new GridLayout(5, 7));
//Sets up and adds the menu bar
menuBar = new JMenuBar();
setJMenuBar(menuBar);
//Adds the File menu
menu = new JMenu("File");
menuBar.add(menu);
//Adds the menu items
menuOpen = new JMenuItem("Open");
menu.add(menuOpen);
menuSave = new JMenuItem("Save");
menu.add(menuSave);
menuExit = new JMenuItem("Exit");
menu.add(menuExit);
//Produses the ComboBox
String[] name={"January", "Feburary", "March", "April", "May", "June", "July", "Augest", "September", "October", "November", "December"};
months = new JComboBox(name);
int m = today.get(Calendar.MONTH);
int d2 = today.get(Calendar.DAY_OF_WEEK);
System.out.print(d2);
months.setSelectedIndex(m);
months.addActionListener(J);
c.add(months);
c.add(Box.createVerticalStrut(10));
switch (months.getSelectedIndex())
case 0: for (int i=1; i<36; i++) {
if(i<4)
day[i] = new JButton();
day.setEnabled(false); }
int k = 1;
day[i] = new JButton(" "+k); b.add(day[i]);
day[i].addActionListener(H); k++;
}break;
//other case statement up to 11 are simaliar }
c.add(a);
//Produces an Array of Buttons
for (int i=1; i<36; i++)
day[i] = new JButton(" "+i);
b.add(day[i]);
day[i].addActionListener(H);
c.add(b);
updateNameField();
setSize(400,400);
show();
}//constructor
private void updateNameField()
monthName = (String) months.getSelectedItem();
class myHandler implements ActionListener
public void actionPerformed(ActionEvent e)
new Text_Area(monthName);
class openHandler implements ActionListener
public void actionPerformed(ActionEvent e)
File f1 = New File ("2003.dat");
simpleSerializer S = new simpleSerializer(f1);
MyDairy = S.readObjectFromFile();
class monthHandler implements ActionListener
public void actionPerformed(ActionEvent e)
updateNameField();
public static void main(String[] args)
new MyDairy();Container c = getContentPane();
c.setLayout(new BoxLayout(c, BoxLayout.Y_AXIS));don't code like above try something like...
Box box=Box.createVerticalBox();
c.add(box);
----so on
Hope this will help... -
ok just this morning i want to update my iphone from OS2 to OS3 and during that time i went to watch tv, but when i came back this happens
http://i391.photobucket.com/albums/oo358/absolutezeromax/IMG_0057.png
it tells me to connect to itunes, but i done it many times and ditunes just keep saying
"you iphone have error
the device is not regonized, unable to prompt service" or something like that, at least i translate back to enlish (i am brazilian)
so i checked out the recovery tut but it wont work (this should reverse back to OS2)
i tried to remove the batteries, sim card still wont work
i tried to reinstall itunes thinking its the programs problem it still wont work
i restarted both the iphone and the computer dozens of times
i use the diagnosis on itunes and its working fine
so i need help fast plzzzzzzzzzzz!!!!yea i did follow a tut
1.turn off phone
2.hold home button
3.connect to itunes
4.keep holding
then it went into recovery mode but after that it just become that screen again -
I really need help this has happend 5 hours ago and the ipod os still showing the apple logo and the buffering icon below it!
It re booted several times till now.
Need help fast!- I suspect that he went to Settings>General>Reset>Erase all content and settings. For 1G or 2G iPod that can take hours and it will likely stall out if not connected to a charging source.
Try the following:
- A reset.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- The connect to computer and try to restore via iTunes.
- Id something is still showing onthe screen, disconnect from computer/charging source and let the battery fully drain. After charging for an hour, Try the reset and restore.
- If you can turn the iPod off, se if placing the iPod in recovery mode and then restore. For recovey mode:
iPhone and iPod touch: Unable to update or restore -
Need help fast with a buying decision - Leadtek 6800 GT
Hi there, I have the opportunity to swap my Club 3D 6800 GT for a Leadtek 6800 GT. The reasons I would do this would be the cooling and the games bundle.
I just wanted to know if anyone knows how the cooling is on this particular card and if it would be better than the reference design?
My other concern is that it has a huge copper heatsink on the back of the card, this would sit directly under the CPU HSF. There really would only be a few millimeters between them and due to the position of the socket on this board, the heat sink fins go up vertically. Would the heat from the card's copper heat sink rise up into the CPU HSF grooves and raise the temperature of the CPU?
Thanks for any help
I kind of need help fast as someone said they were gonna buy my other card of ebay today, there's still time to stop them if this is gonna be a bad ideai would definately take the leadtek one over the club3d card, the cards themselves are all based on refrence designs just different cooling solutions and bundles
and the cooler on the leadtek is a lot better, and it isnt more noisy then the club3d one at all
it has better cooling, and they seem to be the ones which are the most available, and they overclock very well due to the better cooling -
Need Help Fast! Page is dispalying twice in quiz
I have created a quiz using tips from another post in this
forum. I insterted a regular slide with a continue button before
the quiz questions. I insterted another regular slide at the end of
the questions with a re-take button that points to that first
slide. This part is working great. When I take the published quiz,
I click the continue button, and instead of continuing, the slide
redisplays. I click the button again, and it moves forward like
it's supposed to. Any advice?
I'm supposed to have these posted in our LMS today for
testing, so I need help fast!!! Thanks!!What you're seeing is likely the result of a MS patch for IE
in response
to the Eolas patent suit.
MS recently updated IE so any content shown in a page using
the Embed,
Object, or Script tags will need to be 'activated' before
they can be
clicked (or otherwise 'interacted with').
Your home computer probably hasn't had the latest security
rollup
installed, is why you're not seeing the issue on that
machine.
There is a work around, many site mention it. This may be a
good place
to start:
http://www.macromedia.com/devnet/activecontent/articles/devletter.html
Erik
dukekelly wrote:
> Why is it that as soon as you ask for help, you find the
answer?
>
> This isn't a captivate problem at all. It's an IE
problem. Because the button
> is a control in Flash, our systems where I work are
requiring us to click the
> screen to activate the controls. THEN you have to click
the button. When I play
> the movie on my home computer, this phenomenon isn't
happening. Now, how am I
> supposed to deal with that??? ASRRGGGHH!!!
>
Erik Lord
http://www.capemedia.net
Adobe Community Expert - Authorware
http://www.macromedia.com/support/forums/team_macromedia/
http://www.awaretips.net -
samples, tips, products, faqs, and links!
*Search the A'ware newsgroup archives*
http://groups.google.com/groups?q=macromedia.authorware -
I am trying to export a video as an flv but the list of possible formats is much shorter than it used to be. I cannot find any way to make an FLV using the newest version of Premiere Pro. Need help fast! I am on a Mac
Support for exporting to FLV and F4V has been removed. To learn more, please consult this blog post: removal of FLV and F4V export features from Adobe Media Encoder, After Effects, and Premiere Pro | After Effects regio…
-
my screen is completely white, i've tried holding lock and home buttons as seen on you tube something called 'white screen of death' its goes black (think it switches off) then back to the white screen need help fast please!
If you have not done a factory reset on the device, I recommend doing a complete factory reset.
Factory Reset - Warning this will reset device back to original factory settings.
This method will not erase any MDN/MIN information
Turn off the phone
Press Power + Volume Up/Down at the same time and hold until display will show a triage android screen
Display will show:
Reboot system Now
Apply sdcard:update.zip
Wipe Data/Factory Reset
Wipe Cache Partition
Use VOL Down key to scroll down to "Wipe Data/Factory Reset", press home icon to select option and wipe device.
Display shows "All user data will be wiped out", press VOLUME Up to continue or VOLUME Down to exit.
Press Volume Up
Press Home to select "Reset System Now" - device will reboot
If the problem persist I recommend having a store technician take a look at the device.
Copy and paste the link below into your browser's address bar for the store locator.
http://www.verizonwireless.com/b2c/storelocator/index.jsp -
My iphone 6 turned off while i was using face time and it returns with the screen saying Hello mean its reset automatically how is this possible ? Now it requires an id and password to activate which i do not remember need help ? but i do remember the id and password which i was using on itunes and Apple store. please i almoost buy it in 890$ so it will be a big lost please help me.
shahzadfromlahore wrote:
Now it requires an id and password to activate which i do not remember need help ? but i do remember the id and password which i was using on itunes and Apple store. please i almoost buy it in 890$ so it will be a big lost please help me
Who set up the phone? Who's Apple ID was used to activate it? -
HT4061 Serial number not recognized need help
Serial number not recognized need help
<Edited by Host>Not recognized where? And what sort of help are you hoping for from us, your fellow users?
-
HELP PLZ LOOK IPOD WONT SHUT DOWN! NEED HELP FAST!
I HAVE A IPOD TOUCH, IT WON'T SHUT DOWN WHAT SHALL I DO? HELP QUICK PLZ! NEED HELP FAST
- Try a reet:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Next connect to computer and restore if it shows in iTunes.
- If still one, then lett the battery fully drain. After charging fro an hour try the above again.
Maybe you are looking for
-
Error while uploading .xml file for Customer/Vendor List for Italy
Hi All, We are facing problem while uploading the .xml file in DMEE transaction for the new Customer/Vendor List for Italy. We have followed the entire process given in the OSS Note(1090857). We have SAP 4.6c and followed the below steps: 1. Created
-
Will Lion support Word X for Mac from 2001?
It's worked up till now on every OSX including Snow Leopard. Yes I guess I could use Open Office but all my friends are PC users and my daughters use Word at school so I don't want to lose Word otherwise a £20.99 OSX suddenly becomes another £110+ j
-
OOB White Screen Of Death: Silverlight Installation required after each reboot.
Hi, we are getting White Screen Of Death on few user's machine for last few months and a number of users is getting added from last month for the same issue. Earlier we were using the CleanSilverlight from the following site http://support.microsoft
-
Windows Easy Transfer does not connect Windows 8 with Windows 7
A Windows 7 PC and a Windows 8 PC are on a network and working flawlessly. They can access each other either by shared folders or Homegroup. I am trying to transfer files and settings from the Windows 7 PC to the Windows 8 PC using Windows Easy Tran
-
Indesign CS2 personalize software serial number error
ok this is my 2nd time installing Indesign in my computer, but i keep getting an invalid serial number, its the right serial because thats what i used to install it, then when i try to run indesign its asking me for a serial number again to "Personal