Simple battery light question

When my battery is taken out of the computer, pressing the button on my battery causes the first light to blink. When putting it in the computer and plugging in the power adapter, the first light blinks continuously, and the power adapter's color changes to an orange color.
Is this normal? Is this just an indication of the battery charging? Or is there a problem with the battery?

Hi smtlaissezfaire, welcome to Apple Discussions!
If the battery light blinks then this indicates that it needs to be recharged.
The power adapter should stay orange while the battery is charging and upon completion will turn green.
Have you been able to charge the battery until the adapter turns green?
What do the battery lights do then if you press the button?

Similar Messages

  • My iPod shuffle could be seen on iTunes, but it cannot be charged and don't play music. The battery light do not flash at all.

    Like what I mentioned, the iPod do not work, it won't play music and the battery light do not flash.
    But it shows in iTunes, and I could sync music into it.
    I tried to reset all the settings of the iPod, and installed all the new software, but it does not work.
    I don't know if it works before, my friend left it to me. I erased all the data she used before and syncronized all my music inside.
    But it just never worked in my hand...
    I really appreciate all feedbacks! Thanks and please answer this question if you have the similar situation!!

    Are you using the USB docking cable that came with the iPod?  There are separate contact points for power and data, so it is possible for the cable to connect for data, but not for power.  Some third-party replacement cables may be of lower quality, if you do not have the original cable
    However, it seems to be getting power, since the shuffle is operating when connected and you are able to sync when it is connected.  So I think your USB docking cable is working.
    That leaves a problem with the USB port or a problem on the shuffle.
    For the USB port, it may not be supplying sufficient power to charge the battery.  As a test, you should shut down (power off) the computer and disconnect all USB devices, including hub, except for standard keyboard and mouse (if normally used).  If the Mac is a laptop, connect its power adapter (so that it's not running on battery power).  Do this to reset the shuffle
    http://support.apple.com/kb/ht1655
    Start up the Mac, run iTunes, and connect the shuffle to a direct USB port on the Mac.  Any difference...?
    If that does not help, it may be a problem with the shuffle, such as a worn out battery. 

  • HT1199 Battery Lights Dim

    So I was ready to play Minecraft when  I resized the window (because the default one is kind of small) and since the last Minecraft (MC) update, the window flashed white and red when resizing. I was resizing it when it froze, and the display froze. Well. I took out the charger, slept it, unslept it, and at last it displayed the white screen, then the login-after-sleep window, and I quit Minecraft.
    But that isn't the question.
    Since that, the battery lights have become dimmer, as in the green lights being duller. Also you know how they usually fade out after a bit? Well, now they just go out without fading, if you know what I mean. Please help! What's wrong!

    You have a 1-year warranty. If you call after 90 days, they ask for a credit card and will charge you if and only if the problem turns out to be not covered by warranty. If your problem is a bad battery, you will not be charged for phone support.
    That said, they will probably ask you to reset the SMC and PRAM to see if that fixes the problem, so you should try that first:
    http://docs.info.apple.com/article.html?artnum=303319
    http://docs.info.apple.com/article.html?artnum=2238

  • IdeaPad s400 battery status question

    Hi how do i know when the battery if fully charged when the laptop is turn off, the battery light indicator is always on the only way than i can know is touching the charger and if it is cold means that is fully charged.

    Hi Nick,
    Welcome to Lenovo Community Forums!
    I’m glad to inform you the status of the battery and its notifications have been explained in the image below for your S400 Laptop.
    Spoiler (Highlight to read)
    Do post us back for further queries.
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Batterymon -- a simple battery monitor ideal for openbox etc

    Hi All,
    Just added a PKGBUILD for a simple battery monitor that i've been working on.
    http://aur.archlinux.org/packages.php?ID=24694
    i want to thank everyone that has helped me here
    http://bbs.archlinux.org/viewtopic.php?id=67270
    let me know if you have any problems
    there are still lots of things i need to work on but it does work.
    let me know if you have any problems
    http://code.google.com/p/batterymon/

    It works perfectly fine now. Hovering over the panel icon shows the battery status.  Left click brings up a small window with the battery status.  Right click brings up another window which asks if I want to close the app.  The charging/discharging/full status updates as it should.  Zero error messages. 
    This is my new favorite app!  I was using a battery app within xfcepanel on my netbook.  Using this with Docker is SO much lighter.  Great job!
    Small suggestion: make the command to run it simply "batterymon" rather than "batterymon.py".
    Edit:  When I click the icon, the window says my current charge is 95%.  Hovering over the panel icon says I'm still at 100%.  I'm currently unplugged, so it can't possibly be at 100%.  The icon itself is also still blue (battery_power.png) instead of turning green.  No error messages.
    moljac024 wrote:How about some screenshots ? We have no idea what it looks like...
    Panel Icon
    Hovering Over Panel Icon
    Left Click Window
    Right Click Window
    All Status Icons
    Last edited by MarCustomized (2009-03-16 00:52:15)

  • My battery reads that it is 100% charged. However, as soon as I unplug it, it dies instantly. The battery lights are still functional, and everything else is working fine! What's wrong with my battery?

    My battery reads that it is 100% charged. However, as soon as I unplug it, it dies instantly. The battery lights are still functional, and everything else is working fine! What's wrong with my battery?

    Sounds like it may need to be replaced. Contact Apple.
    Basic troubleshooting steps  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • Blinking battery light when fully charged

    My battery light is blinking (low battery power warning) but the battery is fully charged.  I installed a brand new battery, left the AC adapter on overnight, and this morning had a blinking battery light.  It doesn't seem to be a problem except that I won't be able to tell when the battery really is low?  Thoughts anyone?

    rahul.bhat wrote:
    On buying MBP with retina display, one of the Apple genius in the store advised never overcharge it and till date I am acting upon his advice.
    Also, he stated don't put your MBP for continuous charging. Charge it in the same way same as you do for your mobile phone.
    Anyways, I'll keep on looking charged status (100% charge) like what I and other iPhone users do.
    Actually, I take well care of my belongings and iPhone being a premium product, I raised this concern.
    Anyways, Thank you very much for your kind support.
    The genius was misinformed. There is no way to over charge an Apple battery powered device. The charging circuits in the device itself will never allow that to happen. Once the battery is fully charged, charging stops no matter what you do or don't do to the device.
    BTW, this is not an Apple thing. The over charge protection is actually part of the international engineering standards for smart lithium battery technology.

  • Satellite A500 - Battery light flashes when connected to mains power

    Win 7 Satellite A500 PSAM3A-03P00E.
    The battery light flashes when connected to mains power (intermittent fault), when I unplug mains and re-connect flashing stops and battery (high capacity) continues to charge.
    Also when battery light flashes the key board back lighting stays on when it should blank out and if the back lighting is off and the battery light starts flashing the key board back lighting doesn't turn on, all other functions seem to work fine.
    The battery charges and holds charge as it should (when light flashes battery doesn't charge).

    Hi
    Did you notice this issue from first day of purchase?
    Theoretically it could be possible that your battery starts to malfunction
    At the other hand an electronic issue might be possible too
    However, try this:
    Remove ac adaptor and battery. Then press and hold power buttons 30 sec long.
    Then insert the battery and connect AC adaptor again does it helps?
    By the way: is BIOS up to date? If not, perform an update.

  • Battery light flashes when connected to mains, (intermittent fault) battery in good condition.

    Win 7 Satellite A500 PSAM3A-03P00E. The battery light flashes when connected to mains power (intermittent fault), when I unplug mains and re-connect flashing stops and battery (high capacity) continues to charge. Also when battery light flashes the key board back lighting stays on when it should blank out and if the back lighting is off and the battery light starts flashing the key board back lighting doesn't turn on, all other functions seem to work fine. The battery charges and holds charge as it should (when light flashes battery doesn't charge).
    Solved!
    Go to Solution.

    All fixed, the earth contact in the power jack was bent down allowing intermittent contact and limiting current. I bent the contact back up to where it should be and all is good.

  • T40 2373-8CU battery light stays on when unit unplugged and shut down

    i have a T40 that the battery light stays on with the unit shut down and unplugged.  It would appear that the battery is always discharging with this issue.

    I think you may have already been told what the problem is.  However look at this and maybe it will help:
    http://support.apple.com/kb/TA25686?viewlocale=en_US
    http://support.apple.com/kb/TS1365?viewlocale=en_US
    http://support.apple.com/kb/TS1367
    http://support.apple.com/kb/TS1587
    Probably another genius bar appointment is the best way to exactly define the problem.
    Good luck.
    Ciao.

  • Simple X-fi Question, Please Help

    !Simple X-fi Question, Please HelpL I've been looking for an external sound card that is similar to the 2002 Creative Extigy and think I may found it in the Creative X-Fi. I have some questions about the X-fi though. Can the X-fi:
    1. Input sound from an optical port
    2. Output that sound to 5. surround- Front, surround, center/sub
    3. Is the X-Fi stand-alone, external, and powered by a USB or a wall outlet (you do not need a computer hooked up to it)
    Basically I want to connect a TosLink optical cable from my Xbox to the X-Fi. That will deli'ver the sound to the X-Fi. Then I want that sound to go to a 5. headset that is connected to the X-fi via 5. front, surround, and center/sub wires. The X-Fi has to be stand-alone and cannot be connected to a PC to do this.
    Thank you for your help.

    The connector must match, and the connector polarity (plus and minus voltage) must match.  Sorry, I don't know if the positive voltage goes on the inside of the connector or the outside.    Any wattage of 12 or more should be adequate.
    Message Edited by toomanydonuts on 01-10-2008 01:29 AM

  • Satellite L300 - Nothing if I try to start it up, only battery light flash

    Hi i have a L300 and today it turned off and when I tried to start it up again nothing would happen other then the battery light would flash.
    can any body help me please im not that good with computers.

    Hi Alby,
    I have founded an interesting thread here in forum:
    [Which steps should be followed if your Toshiba notebook doesn't start?|http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=21]

  • Constant Orange Battery Light

    I had my iBook G4 plugged in and it was fully charged. Suddenly, the light turned orange and the battery slowly drained down until the computer ran out and the display went black.
    The battery light is orange but I cannot get the computer to turn on. I tried the PMU reset but the computer did not do anything.
    Any ideas?

    Hi, and welcome to Apple Discussions.
    Had any kind of accident happened to the iBook or the adapter before this happened?
    My best guess would be that your adapter has quit working.
    Do you know someone else with an iBook so you can swap adapters and see if that is the problem?

  • Aspire Ethos 8951g Blinking Battery Light - Won't Boot

    When I press the power button on my Aspire Ethos 8951g, the battery light blinks five times at a one second interval and nothing else happens. If I use the switch to disconnect the battery, the battery light does not blink and the computer will not boot. So far I've tried to do a power reset by using the switch to disconnect the integrated battery, removing the RAM, and holding the power button for 90 seconds. It had no effect.  I also bought a new AC adapter, which also had no efffect.  Does anyone know what the five flashes mean? I can't find it in any documentation. The battery life had been pretty good up until this point. 

    IllN,
    Typically the blinking battery light means it has no charge. Here are a few things I can think of:
    Purchasing a new charging adapter rules that out. (good job!)
    Is the charging port connection snug, or is it loose at all? Can you still see the pin inside the port?
    Purchase a new battery.
    Mainboard could be bad.

  • Simple Crop tool question... how do I save the crop section?

    Hi,
    I have a very simple crop tool question. I'm a photoshop girl usually... so Illustrator is new to me. When I select the crop section I want... how do I save it?... if I select another tool in the tool panel, the crop section disappears and I can't get it back when I re-select Crop tool. If I select Save as... it saves the whole document...and not just my crop section.
    Like I said, simple question...but I just don't know the secret to the Illustrator crop tool.
    Thanks!
    Yzza

    Either press the Tab key or F key.

Maybe you are looking for

  • How do I use multiple children classes?

    OK, I'm lost. In the image from a shipping example with LabVIEW, I can see how the circled example works. What I want to be able to do is use more than 1 child, in the same way. Do I have to replicate the code for the other child, or can I somehow ha

  • 1456 Error creating witness in SQL Server 2008 R2...

    Setup is two 2008 R2 Standard servers with a mirrored database. All works fine without a witness - I can perform a manual failover and my test app works off the failover database. Trying to add 2008 R2 Express as a witness to enable automatic failove

  • Power cord not fitting into charge port

    I have a 15-n030us.  The power card has started not fitting snugly into the power port, and the charging is going on and off since it isn't tight.  I didn't do anything to it I know off, or push it in whenit wouldn't go in, wtc, it just sudddenly won

  • Design Document for SAP Workflow

    Hi I am looking for a design document for SAP Workflow. A template for design  document for the SAP workflow will also be fine

  • Can we get a character limit for the subject line?

    Some of the more annoying posts place the entire story in the subject line. (e.g. http://forums.ni.com/ni/board/message?board.id=170​&thread.id=334536&jump=true) The problem is that the edit window when replying blows the margins, making it wider tha