Simple IP profile request, now wee bit confused, p...

Hi
Little background as to why i'm a bit confused 1st
While ago I was getting around 4000-4500kps connection speed using my HH2, then 1 day I had no BB light, phoned helpdesk and was advised my router was dead (no suprise as it was getting old), if i extended contract i could get the all singing and dancing HH3 free (not a prob, always had good service and little issues). Job done and just to wait for new hub, but after trying various other hubs to keep me online inc a borrowed HH3 it wasnt my router that was dead. Anyhow the fault at the exchange was sorted and life was good, till i started realising my downloads and streams were nowhere near as good as before.
Thought i'd request a IP profile reset after doing speedtest and seeing a low profile, but after reading various things I did a few tests and now am confused as to whether a IP profile would be worthless until im sure its all good my end :/
I recieve lower connection speeds with HH3 and higher noise margin than I do using my HH2 (this is also my 2nd HH3 as 1st 1 liked to crash a lot)
Connections to front plate and test socket are very similar in reading, and this is the only thing plugged into my phone line through filter
Home Hub 2 stats
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 0:32:43
Downstream
2,976 Kbps
Upstream
448 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Interleaved
Noise margin (Down/Up)
11.6 dB / 14.0 dB
Line attenuation (Down/Up)
55.0 dB / 31.5 dB
Output power (Down/Up)
18.7 dBm / 12.3 dBm
Loss of Framing (Local)
11
Loss of Signal (Local)
1
Loss of Power (Local)
0
FEC Errors (Down/Up)
5951 / 0
CRC Errors (Down/Up)
0 / N/A
HEC Errors (Down/Up)
N/A / 0
Error Seconds (Local)
2
Home hub 3 stats (same location, wiring etc)
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 00:06:30
Downstream:
2.469 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
12.5 dB / 17.0 dB
Line attenuation (Down/Up):
55.7 dB / 31.5 dB
Output power (Down/Up):
18.7 dBm / 12.5 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
0 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
61371 / 1340
Now previously the noise margin was 14+, but hey it was lower that time
This is the speedtest data from connection with the 'faster' HH2
1. Best Effort Test: -provides background information.
Download Speed
1.8 Mbps
0 Mbps
2 Mbps Max Achievable Speed
Download speed achieved during the test was - 1.8 Mbps
For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps.
Additional Information:
Your DSL Connection Rate :2.98 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
IP Profile for your line is - 2 Mbps
Please help me get back to a better faster connection
ty

Hi there, have left everything running without reconnection etc and my IP profile is now lower than before and max connect of 2mbs
FAQ
1. Best Effort Test: -provides background information.
Download Speed
1.59 Mbps
0 Mbps
2 Mbps Max Achievable Speed
Download speed achieved during the test was - 1.59 Mbps For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps. Additional Information: Your DSL Connection Rate :2.08 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM) IP Profile for your line is - 1.75 Mbps
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
5 days, 19:47:49
Downstream:
2.031 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
9.9 dB / 16.0 dB
Line attenuation (Down/Up):
55.6 dB / 31.5 dB
Output power (Down/Up):
18.7 dBm / 12.4 dBm
FEC Events (Down/Up):
325497558 / 1732
CRC Events (Down/Up):
151164 / 1811
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
344750 / 1160
Error Seconds (Local/Remote):
47134 / 2206

Similar Messages

I'm a bit confused about standby log files

Hi all,
I'm a bit confused about something and wondering if someone can explain.
I have a Primary database that ships logs to a Logical Standby database.
Everything appears to be working properly. If I check the v$archived_log table in the Primary and compare it to the dba_logstdby_log view in the Logical Standby, I'm seeing that logs are being applied.
On the logical standby, I have the following configured for log_archive_dest_n parameters:
*.log_archive_dest_1='LOCATION=/u01/oracle/archivedlogs/ORADB1
VALID_FOR=(ALL_LOGFILES,ALL_ROLES) DB_UNIQUE_NAME=PNX8A_GMD'
*.log_archive_dest_2='LOCATION=/u02/oracle/archivedlogs/ORADB1
VALID_FOR=(ALL_LOGFILES,ALL_ROLES) DB_UNIQUE_NAME=PNX8A_GMD'
*.log_archive_dest_3='LOCATION=/u03/oracle/archivedlogs/ORADB1
VALID_FOR=(ALL_LOGFILES,ALL_ROLES) DB_UNIQUE_NAME=PNX8A_GMD'
*.log_archive_dest_4='SERVICE=PNX8A_WDC ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME=PNX8A_WDC'
*.log_archive_dest_5='LOCATION=/u01/oracle/standbylogs/ORADB1
VALID_FOR=(STANDBY_LOGFILES,STANDBY_ROLE) DB_UNIQUE_NAME=PNX8A_GMD'
*.log_archive_dest_6='LOCATION=/u02/oracle/standbylogs/ORADB1
VALID_FOR=(STANDBY_LOGFILES,STANDBY_ROLE) DB_UNIQUE_NAME=PNX8A_GMD'
*.log_archive_dest_7='LOCATION=/u03/oracle/standbylogs/ORADB1
VALID_FOR=(STANDBY_LOGFILES,STANDBY_ROLE) DB_UNIQUE_NAME=PNX8A_GMD'
Here is my confusion now. Before converting from a Physical standby database to a Logical Standby database, I was under the impression that I needed the standby logs (i.e. log_archive_dest_5, 6 and 7 above) because a Physical Standby database would receive the redo from the primary and write it into the standby logs before applying the redo in the standby logs to the Physical standby database.
I've now converted to a Logical Standby database. What's happening is that the standby logs are accumulating in the directory pointed to by log_archive_dest_6 above (/u02/oracle/standbylogs/ORADB1). They do not appear to be getting cleaned up by the database.
In the Logical Standby database I do have STANDBY_FILE_MANAGEMENT parameter set to AUTO. Can anyone explain to me why standby log files would continue to accumulate and how I can get the Logical Standby database to remove them after they are no longer needed on the LSB db?
Thanks in advance.
John S

JSebastian wrote:
I assume you mean in your question, why on the standby database I am using three standby log locations (i.e. log_archive_dest_5, 6, and 7)?
If that is your question, my answer is that I just figured more than one location would be safer but I could be wrong about this. Can you tell me if only one location should be sufficient for the standby logs? The more I think of this, that is probably correct because I assume that Log Transport services will re-request the log from the Primary database if there is some kind of error at the standby location with the standby log. Is this correct?As simple configure as below. Why more multiple destinations for standby?
check notes Step by Step Guide on How to Create Logical Standby [ID 738643.1]
>
LOG_ARCHIVE_DEST_1='LOCATION=/arch1/boston VALID_FOR=(ONLINE_LOGFILES,ALL_ROLES) DB_UNIQUE_NAME=boston'
LOG_ARCHIVE_DEST_2='SERVICE=chicago LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME=chicago'
LOG_ARCHIVE_DEST_3='LOCATION=/arch2/boston/ VALID_FOR=(STANDBY_LOGFILES,STANDBY_ROLE) DB_UNIQUE_NAME=boston'
The following table describes the archival processing defined by the initialization parameters shown in Example 4-2.
     When the Boston Database Is Running in the Primary Role      When the Boston Database Is Running in the Logical Standby Role
LOG_ARCHIVE_DEST_1      Directs archival of redo data generated by the primary database from the local online redo log files to the local archived redo log files in /arch1/boston/.      Directs archival of redo data generated by the logical standby database from the local online redo log files to the local archived redo log files in /arch1/boston/.
LOG_ARCHIVE_DEST_2      Directs transmission of redo data to the remote logical standby database chicago.      Is ignored; LOG_ARCHIVE_DEST_2 is valid only when boston is running in the primary role.
LOG_ARCHIVE_DEST_3      Is ignored; LOG_ARCHIVE_DEST_3 is valid only when boston is running in the standby role.      Directs archival of redo data received from the primary database to the local archived redo log files in /arch2/boston/.
>
Source:-
http://docs.oracle.com/cd/B19306_01/server.102/b14239/create_ls.htm

Save Options a Bit Confusing

Hi,
I've been using LabVIEW for about 7 months now, and am still a bit confused about the save options. It seems that whenever I modify a sub-VI for my app, the previous sub-VI I created ends up with the same settings that I changed in the newly modified one.
Example: I use an existing VI created by Daytronic Corp for monitoring a binary signal. I change the channel and a few other settings, and name the file oil press.vi, saving it in the new folder I created for my app. Then I close the oil press.vi I modified, then close the original, unchanged VI without saving it. When I create another VI starting with the original, unmodified one again, and save it using the same procedure, but using a different filename (let's call it fuel press.vi), oil press.vi takes on the characteristics of fuel press.vi, although the filename is still oil press.vi. So, I end up having to use the "replace" option on the block diagram and select oil press.vi as the replacement file. I have to keep doing this for every sub-vi I create.
This take a lot of time and is a bit annoying.
I hope you can understand what I'm saying. The Save options seem confusing to me, with all the references to keeping a vi in memory, closing the original, etc. Is there some text or a tutorial online that explains the save options in a simpler, more direct form? I have even read about it in my book (Labview for Everyone) and it doesn't go into much more detail about how saving the Vis actually works.
Thanks!
Todd Munsell
Turbine Engine Test Technician/IT Tech
Wood Group Pratt & Whitney Industrial Turbine Services, LLC
Plattsburgh, NY

Hi Mike,
Actually, I'm using LV 8.5. It's the descriptions of the save options that are slightly confusing. The information about what's left in memory and what's closed and opened is what's got me baffled.
For example, what, in layman's terms, do each of these options below mean... exactly? I would think that an option that simply says "Save as path/filename" would be enough. Then, the renamed, saved file stays open, since that's the one that's currently being used, and the original is closed and left as it was. Which option (and sub-option) would I choose to do this?
The number of options below seems a bit excessive, and not very clearly defined, at least to me. Even the explanation in the book "LabVIEW for Everyone", which is supposed to be for beginners, doesn't do a very good job of describing exactly what each option does. Thanks again!
Original file—Displays the path to the open file. You can
use this field to determine the location of a file on disk.
Copy—Creates and saves a copy of the file in memory to disk with a name you
choose. If you enter a new file path or name for the file, the original file on
disk is not overwritten or deleted.
Substitute copy for original—Both the original file and the
new file exist on disk, but the original VI closes and the new VI opens. Use
this option if you
want to create a copy of the original file and immediately edit the copy.
Caution If the original file has
calling VIs in memory, this option updates all these callers to refer to the new
file.
If the original file is in a project
library or project, this option substitutes the new file for the original in the
project library or project.
Create unopened disk copy—Both the original file and the
new file exist on disk, but only the original file remains open in memory. Use
this option if you
want to create a copy of the original file but continue editing the original
file, for example, if you want to create a backup copy. This option does not update
callers in memory to refer to the new file. You can update callers manually by
finding all instances of a
VI and updating the name of each instance. If the original file is in a
library or project, this option does not add the new file to the same library or
project.
Open additional copy—Both the original file and the new
file exist on disk and are open in memory. You must give the copy a new name,
because two files of the same name cannot exist in the same application instance
at the same time. Use this option if you want to create a copy of the original file,
continue editing the original file, and also immediately edit the new file. This
option does not
update callers in memory to refer to the new file. You can update callers
manually by finding all
instances of a VI and updating the name of each instance. If the original
file is in a library or project, you have the option of adding the new
file to the same library or project by placing checkmarks in the appropriate
checkboxes. If you place a checkmark in the checkbox to add the copy to the
library, the checkbox to add the copy to the project is disabled and
unchecked.
Rename—Renames the file in memory with a new name you
choose. This option
closes and deletes the original file and opens the file with the new name, so
only the new file exists on disk and in memory. Use this option if you want to
change the name and/or location of the original file.
Caution If the original file has
calling VIs in memory, this option updates all these callers to refer to the new
file.
If the original file is in a library or
project, this option adds the new file to the same library or project,
and removes the original file.
Duplicate hierarchy to new location— Use this option if you want to
save the original
VI and its hierarchy to a new location. You might want to rename the new VI
hierarchy after duplicating it.
Message Edited by tmunsell on 08-09-2008 01:54 AM
Message Edited by tmunsell on 08-09-2008 01:56 AM
Todd Munsell
Turbine Engine Test Technician/IT Tech
Wood Group Pratt & Whitney Industrial Turbine Services, LLC
Plattsburgh, NY

Audio and Visuals are a wee bit out of sync!!

hello there
i seem to be having a wee bit of a problem. it started a couple of weeks backs and i figured it might just be a one off thing, but now it's getting annoying.
basically when i watch a dvd or watch youtube, or stream a trailer online, the audio seems to be a half second slow and doesn't sync exactly with the visuals.
any adivce or help please??! also, when i listen to itunes, the sound at times is staggered.......

i know how to solve the issue on a mac. can you access one so that i can give you instructions to correct that?

I'm a bit confused. Since my original camera format was 720/60p, and I converted the footage to Pro Res422 in order to edit in Final Cut Pro 7, should I convert back to a higher quality format before sending the file to DVD Studio Pro?

I'm a bit confused. Since my original camera format was 720/60p, and I converted the footage to Pro Res422 in order to edit in Final Cut Pro 7, should I convert back to a higher quality format before sending the file to DVD Studio Pro? If so, which Compressor codec is best to use in order to preserve the original 720/60p? How do I maintain the highest quality?

No...ProRes is a high quality format. Finishing format. Many TV networks take that as a final deliverable.
BUT...DVDs aren't high definition...they are SD. You cannot make a 720p60 DVD with DVD Studio Pro. Any DVD you make will be SD...720x480. The only HD DVD format out there is BluRay, and for that you need a BluRay burner.
As for making a high quality DVD...using the BEST QUALITY settings in Compressor will work:
#42 - Quick and dirty way to author a DVD
Shane's Stock Answer #42 - David Roth Weiss' Secret Quick and Dirty Way to Author a DVD:
The absolute simplest way to make a DVD using FCP and DVDSP is as follows:
1. Export a QT movie, either a reference file or self contained using current settings.
2. Open DVDSP, select the "graphical" tab and you will see two little monitors, one blue, one green.
3. Select the left blue one and hit delete.
4. Now, select the green one, right click on it and select the top option "first play".
5. Now drag your QT from the browser and drop it on top of the green monitor.
6. Now, for a DVD from an HD source, look to the right side and select the "general tab" in the track editor, and see the Display Mode, and select "16:9 pan-scan."
7. Hit the little black and yellow burn icon at the top of the page and put a a DVD in when prompted. DVDSP will encode and burn your new DVD.
THATS ALL!!!
NOW...if you want a GOOD LOOKING DVD, instead of taking your REF movie into DVD SP, instead take it into Compressor and choose the BEST QUALITY ENCODE (2 pass VBR) that matches your show timing. Then take THAT result into DVD SP and follow the rest of the steps. Except you can choose "16:9 LETTERBOX" instead of PAN & SCAN if you want to see the entire image.

A bit confused with your Gap Analysis example

Hi Robert,
As I analyzed your Gap Analysis example, I getting a bit confused.
In your message below, with the 0 in the 0Customer, arent you already (by BW convention), assuming that 0Customer is a standard business content object?
... but you also in the same statement noted that ..and std business content doesn't provide it in your extractor
I am thinking, it is a business content object already, why does he say the source system doesnt provide it?
Also, what were you referring to as in your extractor did you mean in the source system?
Quote from Robert Gap analysis process has to be performed when you know that you can use a std business content extractor (or cube or something else) and you have to compare it yo your actual requirements: do you need 0CUSTOMER and std business content doesn't provide it in your extractor...well, now you have done a gap analysis !
====

Caud,
sorry, but I think that Praveen explanation doesn't exactly match with what do you need to know...
The Gap Analysis Fit is a step inside an ideal business blueprint of a BW project implementation (but, clearly, the same concept can be applied to several situation...).
During this step, after having collected all the client's requirements, you have to higlight what you need (or what you can) to use to build what the user wants.
In this analysis, you find that a business content datasource (found via help.sap.com or after the SDN's forum suggestion or...) can provide almost all the required fields (since a datasource is a collection of several fields..).
Anyway, notwithstanding this, you realize that this datasource is good only for a 95%, because it's missing the info related to the customer (usually shown with 0CUSTOMER object, but you can use a ZCUSTOMER or something else...the only important thing is that you need this info!).
Ok, you know that in order to fit this gap, you have to build your own enhancement with a little userexit to fill this missing field: THIS IS THE GAP ANALYSIS FIT !!!
This explanation applies also to a std cube, to a std query and so on...
Sure, you use std business content, but why you ask "why does he say the source system doesnt provide it" ???
The std objects can't provide always all we need, but only, if we are lucky, a part (more or less) of it...and at this point you need to perform this kind of analysis...
Hope now is clearer...
Bye,
Roberto

A little bit confused about my review app

Hi,
I'm a little bit confused .
I have released on store my app for IOS 5.1 several mouths ago. Now to check that my app is IOS 6 compatible have installed xcode 4.5.
I thought that my correct tests were :
- build for IOS 6.0 to check if it run on for device that upgrade to IOS 6.0
- build for IOS 6.0 to check if it run on device that NOT upgrade to IOS 6.0 (still 5.1)
but i cannot run for simulator 5.1 with xcode 4.5!!!
how i can check it!!
Maybe i'm wrong . Could someone help me for my doubt ?
Best Regards
Al

Hardware > Version > 5.1
Don't forget to test it on real hardware. There should be plenty of iOS 5.1-limited devices available real soon now. Keep one of those for testing.

Calendar component: I am a bit confused on the bean to use

Hi all,
I would like to use the calendar component.
I have just read http://www.oracle.com/technology/products/jdev/11/how-tos/calendar/calendar.htm , http://download.oracle.com/docs/cd/E12839_01/web.1111/b31974/web_adv.htm#CHDIFFGA (paragraph 27.5) , the chapter 15 of the user interface developer's guide and I have seen the adf demo.
I am a bit confused on the classes to use to manage the calendar. I can't find the class calendar model described on the manual and other links, while the adf demo uses a lot of classes: DemoCalendarActivityBean, DemoCalendarBean, DemoCalendarModelBean, DemoDateCustomerBean, DemoCalendarActivity, DemoCalendarModelWrapper, DemoCalendarProvider, DemoSingleProviderCalendarModel.
First of all, I don't understand all the functionality of these classe, but the most important is that I don't understand the difference between DemoCalendarModelBean and DemoCalendarModelBean.
If I define a table in my database, like described on the links/manual, what classes do I need?
Thanks
Andrea

User,
OK, now I'm completely, utterly, and totally confused.
The sample application workspace that I downloaded from the how-to link you provided has a CalendarBean class, which is simply a managed bean. I don't see either DemoCalendarBean nor DemoCalendarModelBean. If you are using ADF Business Components as your model layer, you don't need to muck about creating calendar models. As the how-to says:
An ADF Faces Calendar component must be bound to a CalendarModel class. This class can be created for you when you use ADF Business Components to manage your calendar's data. For example, say you have data in your data store that represents the details of an activity, such as the date, time, title, location, and owner. When you create an entity object to represent that data, and then a view object to display the data, you can drag and drop the associated collection from the Data Controls panel to create the calendar. JDeveloper will declaratively create the model and bind the view to that model so that the correct data will display when the calendar is launched. The [url http://download.oracle.com/docs/cd/E12839_01/web.1111/b31973/af_calendar.htm]web user interface developers guide secton on creating a calendar is pretty clear on all of the classes you have to create if you are not using ADF BC.
John

Graphics Driver - Getting a bit confused

Dotted around this forum reference is always made to 'check that you have the latest graphic drivers installed', in another post referenced to flickr is a way 'one user has managed to tweak his graphic card settings' but somewhere else the advice given is 'disable the NVIDIA Control Panel'.
Forgive me, but this is all getting a bit confusing as LR is about the only application where I have come across so much confusion. Could someone in the know kindly tell me what the latest advice is please? In this post (mentioned before) Adobe actually suggest using the Windows driver http://kb.adobe.com/selfservice/viewContent.do?externalId=kb400808&sliceId=1
Surely as NVIDIA is one of the more common display cards/drivers Adobe would have tested LR using their latest graphics cards - no? Indeed, if this is the case, wouldn't it be useful to users if Adobe actually published what graphic cards had been tested with LR and what the settings should be for each of the latest cards?
It might be looking at things in a very simple way, but surely the onus is upon Adobe to ensure that their application works with at least the newer systems and not put the user through exhaustive tests, tweaks and experimentation in the HOPE that performance will be improved.
Incidentally, I've got installed a NVIDIA 8800GT

I do not believe Lr uses the video GPU for processing and therefore there are no specific graphic card requirements.
What Adobe is recommending (and what I have done) is to disable the nView Desktop Manager. This software controls some apects of a desktop setup but is entirely optional and is not required for a multi monitor configuration using nVIDIA cards. The nView Desktop Manager is software separate from the graphics driver.
Why nView Desktop Manager causes Lr to go haywire is beyond me. And the nVIDIA forums have no mention of problems with Lr.

My iphone 4 does not appear in my(windows 7) lap top, when i connect i can hear the sound of usb connected, but its not appear in the itunes or computer, and its not charging as well, bit confusing

my iphone 4 does not appear in my(windows 7) lap top, when i connect i can hear the sound of usb connected, but its not appear in the itunes or computer, and its not charging when i connected to the laptop as well, bit confusing, help please

Take a look at this link, http://support.apple.com/kb/TS1538

IAM-3056160:Modify User Profile request cannot set or change attribute Job Code, since it is not defined in the corresponding data set.

I am trying to modify the value of the field "Job Code" through API I am getting the following error.(OIM11gr2). I do not get this error when updating the other fields. There is a field by the name USR_JOB_CODE in the database. When I poked around I found that there is no Job Code field in the User Form. Any ideas?
IAM-3056160:Modify User Profile request cannot set or change attribute Job Code, since it is not defined in the corresponding data set.:Modify User Profile:Job Code
oracle.iam.identity.exception.ValidationFailedException: IAM-3056160:Modify User Profile request cannot set or change attribute Job Code, since it is not defined in the corresponding data set.:Modify User Profile:Job Code
 at weblogic.rjvm.ResponseImpl.unmarshalReturn(ResponseImpl.java:237)
 at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:348)
 at weblogic.rmi.cluster.ClusterableRemoteRef.invoke(ClusterableRemoteRef.java:259)
 at oracle.iam.identity.usermgmt.api.UserManager_nimav7_UserManagerRemoteImpl_1036_WLStub.modifyx(Unknown Source)
 at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
 at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
 at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
 at java.lang.reflect.Method.invoke(Unknown Source)
 at weblogic.ejb.container.internal.RemoteBusinessIntfProxy.invoke(RemoteBusinessIntfProxy.java:85)
 at $Proxy2.modifyx(Unknown Source)
 at oracle.iam.identity.usermgmt.api.UserManagerDelegate.modify(Unknown Source)
 at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
 at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
 at sun.reflect.DelegatingMethodAccessorImpl.invoke

THanks for your reply. Here is the snippet from User.xml that contains info about job code.
<entity-attribute>Job Code</entity-attribute>
<target-field>usr_job_code</target-field>
<field name="usr_job_code">
<type>string</type>
<required>false</required>
</field>
<attribute name="Job Code">
<type>string</type>
<required>false</required>
<searchable>true</searchable>
<multi-valued>false</multi-valued>
<MLS>false</MLS>
<multi-represented>false</multi-represented>
<attribute-group>Basic</attribute-group>
<metadata-attachment>
<metadata>
<name>multi-valued</name>
<value>false</value>
<category>properties</category>
</metadata>
<metadata>
<name>user-searchable</name>
<value>true</value>
<category>properties</category>
</metadata>
<metadata>
<name>category</name>
<value>Preferences</value>
<category>properties</category>
</metadata>
<metadata>
<name>bulk-updatable</name>
<value>true</value>
<category>properties</category>
</metadata>
<metadata>
<name>read-only</name>
<value>false</value>
<category>properties</category>
</metadata>
<metadata>
<name>visible</name>
<value>true</value>
<category>properties</category>
</metadata>
<metadata>
<name>encryption</name>
<value>CLEAR</value>
<category>properties</category>
</metadata>
<metadata>
<name>display-type</name>
<value>TEXT</value>
<category>properties</category>
</metadata>
<metadata>
<name>system-controlled</name>
<value>false</value>
<category>properties</category>
</metadata>
<metadata>
<name>max-size</name>
<value>512</value>
<category>properties</category>
</metadata>
<metadata>
<name>custom</name>
<value>false</value>
<category>properties</category>
</metadata>
</metadata-attachment>
</attribute>
I am able to retrieve the value of the Job Code attribute without any problem with the following code.
System.out.println("JOB Code: "+user.getAttribute("Job Code"));

Hi all, I'm still having problems with my security questions as they were not the ones I answered. Now I'm confused

Still having problems with my security questions as they were not the ones I answered and now I'm confused.

Howdy Paul,
If you are having an issue with your Apple ID security questions, you can reset them using the steps in this article -
If you forgot the answers to your Apple ID security questions - Apple Support
Thanks for using Apple Support Communities.
Best,
Brett L

Hi we have apple credentials for downloading OS and creating Provisioning profiles. Now we are trying to upgrade the Mac OS 10.7.3 version. do we need should buy this version from appStore. or can it be download from the apple site for free? Many thanks

Hi we have apple credentials for downloading OS and creating Provisioning profiles. Now we are trying to upgrade the Mac OS 10.7.3 version. do we need should buy this version from appStore. or can it be download from the apple site for free? Many thanks in advance!

Whether you need to buy Mac OS X 10.7.3 depends on what version of OS X you have now.
If you have OS X 10.6.x or lower it is a paid upgrade from the Mac AppStore.
If you have OS X 10.7.x it is a free upgrade you get using Software Update on your Mac.

Since Lion system profiler is now a question mark in the dock. Can i get it back?

Since Lion, system profiler is now a question mark in the dock. Can I get it back? dsso

In Lion, there is no Systim Profiler. It is System Information now located in the Utilities Folder. Open that up and select to keep it in the Dock.
Drag the icon for system profiler off the Dock.

Message says: "can not get mail, the connection to the server failed" . Now I'm confused because all the mail shows up perfectly.

I just upgraded to the 5s. I have several mail accounts and I'm getting a message that says: "can not get mail, the connection to the server failed" . Now I'm confused because all the mail shows up perfectly.

Well it does it every time I go to mail and is driving me nuts. It never happened on my iPhone5, just on this 5s.

Simple IP profile request, now wee bit confused, p...

Similar Messages

Maybe you are looking for