Simple lan to lan routing (not working)

I have created a RRAS LAN only router on windows 2008 R2
segment 1
172.16.0.0        network
172.16.16.20    gateway
255.255.0.0      subnet
segment 2
10.0.0.0        network
10.0.0.1    gateway
255.0.0.0      subnet
RRAS interface A 172.16.16.20
RRAS interface B 10.0.0.1
i installed rip 2 protocol
still client cant ping hosts on the opposite network, any idea what i may be doing wrong ?
regards
Faisal Gillani

route print does not give you any clue?
any VLANs (manage switches) configured on the network?
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
No no VLAN present
Here is my routing print , this si a VM based windows server which have two nic, each connected to diffrent lan's i have a feeling this is going to be something very basic which i am doing wrong :-)
IPv4 Route Table
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x10003 ...00 15 5d 10 10 04 ...... Microsoft Hyper-V Network Adapter #2
0x10004 ...00 15 5d 10 10 03 ...... Microsoft Hyper-V Network Adapter
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface Metric
         10.0.0.0        255.0.0.0         10.0.0.1         10.0.0.1     10
         10.0.0.1 255.255.255.255        127.0.0.1        127.0.0.1     10
   10.255.255.255 255.255.255.255         10.0.0.1         10.0.0.1     10
        127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
       172.16.0.0      255.255.0.0     172.16.16.20     172.16.16.20     10
     172.16.16.20 255.255.255.255        127.0.0.1        127.0.0.1     10
   172.16.255.255 255.255.255.255     172.16.16.20     172.16.16.20     10
        224.0.0.0        240.0.0.0         10.0.0.1         10.0.0.1     10
        224.0.0.0        240.0.0.0     172.16.16.20     172.16.16.20     10
255.255.255.255 255.255.255.255         10.0.0.1         10.0.0.1      1
255.255.255.255 255.255.255.255     172.16.16.20     172.16.16.20      1
===========================================================================
Persistent Routes:
None
thanks in advance :-)

Similar Messages

T61 Intel Pro 1000 Lan Adpater not working

Hello, I have a T61 7664-17U. I recently had to replace the hard drive on this system due to drive read errors.
I have all of my system up to date and working, except the lan adapter. I have the 82566MM Gigabit connection in the network connections but there is no communication when i connect the rj45 cable. I would like to get this working as my office does not
have a wireless connection and i need to use the system there. Could anyone please guide me to the correct driver and how to install it so i get things finished up and working. Any suggestions would be appreciated.

check BIOS / configuration and see if INTERNAL LAN is enbaled or disabled. i had this happen when my wireless and lan were not working. fixed it in bios.
T7600, T60p - 2GB - 2.33GHZ - 100GB

Usb driver on the left side near the lan are not working

The brightness keys are also not working and the usb drives on the left near the lan are not working.

Hi:
Did you reinstall the operating system?
If so, you are probably missing the graphics and USB3 drivers.
Graphics:
File name: sp56458.exe
USB3: Download and install both of these drivers and reboot.
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=5229463&swItemId=ob_125616_1&swEnvOid=405...
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=5229463&swItemId=ob_123787_1&swEnvOid=405...
If there is a device labeled SMBus Controller in the device manager, this driver should work for that device.
http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=cp_119081_1

EA 6500 - LAN Does Not Work

With the E4100 I can setup a LAN game of call of duty mw3 and 1 xbox can join the other, pretty simple, Ive always been able to do this with all xbox games that have LAN ability.
With the EA6500 I see the game is availible on LAN, but I can never connect to the game, it tries to connect and says cannot connect.
Any LAN settings Im missing here, or just another EA6500 bug to add to the list?

Theoretically, having two xbox connected to a single router may work based on the post of previous users but technically one router could only cater one gaming console. What you can do is perhaps to try to open the ports: tcp 3074 27014-27050, udp 3074 27000-27030; or to DMZ the xbox to the router.

Satellite A110-228 LAN does not work after hibernate

Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
After a reboot, the network functions as usual (gets a IP address from the DHCP server)
Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
The wireless network will be restored after a hibernate.
It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
Any suggestions?
Wilm Boerhout

Hi guys
In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
I think the options are disabled by default.
Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
Please check this how to enable WOL (first time use):
1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
2. Enable Wake-up on LAN
3. Click [Apply]. System will request to reboot.
4. After the reboot go to [Start] -> [Control Panel] -> select [System]
5. On system properties dialog box select [Hardware] tab -> click [Device manager]
6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
8. Press [OK] to close the dialog box.

WIRLESS LAN IS NOT WORKING IN IT.

HI I AM USING WINDOWS 8 WIRLESS LAN(DRIVER) IS NOT WORKING(INSTALLING) IN IT CAN U PLEASE RESOLVE MY PROBLEM

sunny_22j wrote:
i have purchased iphone 5s from dudai and it doesnt have face time,
And it never will. Phones sold in Dubai do not have facetime installed per government regulations.

Onboard Broadcom LAN does not work: code 10 [Master3]

Hi,
OK, I finally get my K8N Master3 working - Opteron 240, Win XP SP2. But I can't get the onboard LAN to work.
When I turn on the PC I get this in the device manager: http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom1.jpg
and the error message is "device cannot start, code 10" : http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom6.jpg
I can disable the devices then re-enable them and this makes it look like it's all OK: http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom2.jpg
However, although packets are being sent and the network status shows packets being sent and received. I can't ping any computer on the network! I have tried using just 1 PC via a cross over cable (without the extra LAN cards listed in the device manager). But although it looks like it should all work, nothing gets sent.
This is the driver I'm using: http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom3.jpg
Initially, there is no MAC address for the ports. Windows just shows 0's in the connection status support tab.
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom4.jpg
So I assigned a value for the MAC address based on an existing Broadcom network card: http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/broadcom5.jpg
BTW. when I reboot, the broadcom controller is again listed as not working in the device manager.
Anyone with any ideas?
Adrian
p.s. if you can't see the links, the my WWW might just be down, it hangs every now and then :-(

OK, I've taken it out of the case and plugged one of the LAN ports into a laptop. The laptop is constantly pinging it and the server is pinging the laptop. Unfortunately it's the same as before. The broadcom controller(s) are not working when XP boots, giving a code 10. It is possible to disable them and enable them. This makes it look like they might work. Packets are received, nearly. The lights on the ports light up and the speed is automatically detected and set.
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless1.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless2.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless3.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless4.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless5.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless6.jpg
http://www.AdrianJudd.com/~AdrianX/photos/MSI/broadcom/caseless7.jpg
When I put the system back together again I placed the other LAN cards in different PCI/PCI-X slots. This caused the Intel card to give a code 10. When I swapped it back it was OK. Unfortunately, I can't swap the Broadcom controller around as it's on the MB. I also tried the SCSI card in different PCI/PCI-X slots. Finally, I now get a code 10 from my LSI MegaRAID card. So I'll have to re-install XP
There's not much I can do really. The screen shots above are the most basic setup I can have, ie. SCSI card and 1 SCSI drive (in the SCSI enclosure at the back). I've never seen a code 10 error before, and after taking the m/b out and putting it back in again, I ended up with 4 at once! I was thinking about maybe trying Win XP 64 bit.

HT2452 I updated my iMac and the Wifi & LAN are not working

I updated my iMac and the Wifi & LAN are not working

Firefox stores site favicons to display next to the corresponding bookmark. If those have disappeared ''completely'', it might indicate a problem with your bookmarks list. If some of the site favicons still show, it could be this: for bookmarks without favicons, Firefox recently changed from showing a "blank page" icon to showing the dotted rectangle icon.

Lenovo U350 - Windows 7 - Network (LAN, WiFi) not working

Hi
My WiFi is not working on my new computer Lenovo U350. I have pressed FN+F5, but it says I have to turn on the switch. Where is this switch??
I've tried to reinstall the network drivers as well...

Look on the left side of the laptop, in front of the USB port. There is a slide switch there.
Page 4 of the users manual shows a picture. Look here: http://consumerdl.lenovo.com.cn/UserFiles/UserGuide/en/User's%20guides%20and%20manuals/U350/Lenovo%2...
Bill

Back To My Mac to a Time Capsule through a 3Com Router not working

I have a Mac Book Pro (10.5.7), Time Capsule (7.4.1), 3Com Office Connect Wireless Router (3CRWDR101A-75), a trial subscription to Mobile Me and a 2.5G iPhone (2.2.1).
I have been unable to get BTTM from my Mac on a remote wireless connection to my Time Capsule working - hence this post.
The set up of the Time Capsule was quite straightforward (as I would have expected from Apple) and I quickly established local and remote iCal / Address Book sync between my Mac, www.me.com and my iPhone. I have enabled and am the 2.4 and 5GHz bands on the Time Capsule and the wireless air interface on the 3Com router has been turned off. All of internet and email services on my Mac work well locally and Time Machine work. So far so good.
However, I am unable to 'see' my Time Capsule in Finder from any WiFi network that is not my home network. When at home I have full access to Time Capsule's disk.
My 3Com Office Router 3CRWDR101A-75 is not on the list of supported routers (nor is any other 3Com Router) but it does provide UPnP and NAT as required according to Mobile Sync notes including http://support.apple.com/kb/HT1552 and http://support.apple.com/kb/HT1552. Despite my best efforts, I have been unable to find out from Apple's MobileMe support if there are any minimum requirements for any router to work with Back To My Mac so can't check to see if my 3Com router will ever work with BTTM or not.
Does anyone have any similar experience with setting up a 3Com Office Connect router to work with Back to My Mac?
Do I need to check / Can I check if my Time Capsule has been registered with the Mobile Me servers?
Do I need to enable any specific ports on my 3Com Office Connect router?
Basic settings:
Time Capsule: green light - all OK
AirPort Utility>Internet: Connection Sharing: Off (Bridge Mode)
AirPort Utility>Advanced>Mobile me: account set up
AirPort Utility>Advanced>IPv6: IPv6 mode = Node, at the request of Apple Mobile Me support
System Preferences>Mobile Me>BackToMy Mac: On (green light).
3Com Office Connect Router: DCHP server: On
3Com Office Connect Router: Firewall level: High (default)
3Com Office Connect Router: Disable NAT: Off (default)
3Com Office Connect Router: Enable Universal Plug & Play: On
3Com Office Connect Router: Enable IPSEC-NAT pass through: ON, at the request of Apple Mobile me support
Com Office Connect Router: DMZ: enable 1-to-1 NAT: Off (default)
Any ideas?
Thanks.

Quick update on troubleshooting BTTM (or rather Back To My Time Capsule)...
Surprising;y, no 3Com products listed in http://support.apple.com/kb/TS1304. 3Com tech support stated that no OfficeConnect products have been qualified against BTTM and my specific router does not support IPv6 over IPv4 encapsulation.
MobileMe support were not able to help, citing the fact that I had an unsupported router.
I have made no change to my modem/router config since first posted but since an upgrade of my TC to 7.4.2 I have been able to use BTTM with my TC (bridge mode) and my OfficeConnect modem/router (802.11b WiFi disabled).
I have made limited testing from other remote locations from my MBP and also proved that it worked over a 3G/UMTS connection on the UK's 02 network also
MobileMe still reporting uPnP / NAT problem on my MBP when working remotely though.
http://discussions.apple.com/message.jspa?messageID=9733258 confirms that this has been solved and, apart from the anomalous Mobileme status message, I can agree.
Good news so now do not need to swap out my 3Com router. Also shows that this 3Com product does meet BTTM connectivity requirements.
Message was edited by: Elise49
Message was edited by: Elise49

Linksys WRT54G Wireless-G Router Not working

I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

ISE version 1.3 and static route not working

This command works without any issues with ISE version 1.1 and 1.2:
ip route 192.168.1.1 255.255.255.255 gateway 127.0.0.1
However, it does NOT work in ISE version 1.3. See below:
ciscoisedev/admin(config)# ip route 192.168.1.1 255.255.255.255 gateway 127.0.0.1
% Warning: Could not find outgoing interface for gateway 127.0.0.1 while trying to add the route.
% Error: Error adding static route.
ciscoisedev/admin(config)#
Any ideas anyone?

So it appears that there is no option to lock down access to the shell now that the command that you used to use is no longer valid. What is worse is that there isn't an option to create an ACL in the shell that you could attach to the interface. So I would recommend that you create a defect with Cisco TAC and get this re-added or request that ACL functionality is added.
For the GUI (in case you were not already aware of this), you can restrict access from Administration > Admin Access > Settings > Access > IP Access

Why my hp simple pass website login does not work with firefox latest version ?

I have the latest version of firefox version 16.0.1 and my hp simple pass website login does not show up like it worked in IE9.

I updated all the add ons already and I already reinstalled the HP simple pass after I installed firefox. I think that the new firefox is not yet compatible with the software (HP simple pass)

Simple WD4A Portal Eventing does not work

Hello togehter,
I'm trying to get a simple Portal Eventing to work with two WebDynpro ABAP components. I read several threads as well as a blog from Thomas Jung about this but still have no eventing. What am I doing wrong? I think that it might be only a little obstacle but I can't get it. So what I didi is:
1.) Created 1st WD4A application with a button and an action behind that button:
DATA: l_api_component TYPE REF TO if_wd_component,
        l_portal_manager TYPE REF TO if_wd_portal_integration.
l_api_component = wd_comp_controller->wd_get_api( ).
l_portal_manager = l_api_component->get_portal_manager( ).
l_portal_manager->fire(
    portal_event_namespace = 'urn:my.namespace'
    portal_event_name      = 'test_event'
    portal_event_parameter = 'testValue' ).
2.) Created 2nd WD4A application with the following code in the WDDOinit-Method:
DATA: l_api_component TYPE REF TO if_wd_component,
        l_portal_manager TYPE REF TO if_wd_portal_integration,
        view TYPE REF TO if_wd_view_controller.
l_api_component = wd_comp_controller->wd_get_api( ).
l_portal_manager = l_api_component->get_portal_manager( ).
view ?= wd_this->wd_get_api( ).
l_portal_manager->subscribe_event(
    portal_event_namespace = 'urn:my.namespace'
    portal_event_name      = 'test_event'
    view                   = view
    ACTION                 = 'CATCH_EVENT' ).
and an action.
method ONACTIONCATCH_EVENT .
data: EVT_NAME type STRING,
        evt_parameter type string.
EVT_NAME = WDEVENT->GET_STRING( NAME = 'PORTAL_EVENT_NAME' ).
if EVT_NAME = 'test_event'.
    evt_parameter = WDEVENT->GET_STRING( NAME = 'PORTAL_EVENT_PARAMETER' ).
    DATA:
      ls_text TYPE if_main=>element_main,
      node_main TYPE REF TO if_wd_context_node,
      elem_main TYPE REF TO if_wd_context_element.
    node_main = wd_context->get_child_node( name = `MAIN` ).
    evt_parameter = 'IT WORKED'.
else.
    evt_parameter = 'did not work'.
endif.
ls_text-text_receiver = evt_parameter.
node_main->bind_element( ls_text ).
endmethod.
3.) FInally I created two iViews (for each WD4A application) and a page, linked the iViews in the page and made a preview. Unfortunately nothing happend in the second iVIew with the 2nd WD4A application in it.
Any help?
Thanx in advance
Matthias

Hello,
thanks for your answers. But the problem is not yet solved, the link gives nothing new for me.
To amend my first post:
After having created and activated my both small WD4A applications, I created 2 similar iViews (iViews for WebDynpro -> and chose WD ABAP) in my portal. Both iViews have the same namespace (which is SAP - is this ok?) and no application parameter.
Then I created both a Standard SAP page and a WebDynpro proxy page and added the 2 iViews as deltalink. The page and the iViews have the same prefix (but this is not important, isn't it?).
--> In both pages the portal eventing does not work
The ABAP server and the Portal server are the same machine and I call the portal with the full qualified domain name:
http://<servername>.<domain>:50000/irj/portal
When I test my WD4A applications in se80 I get the path http://<servername>.<domain>:8000/sap/bc/webdynpro/sap/z_event_receiver?sap-language=EN
so this is the same domain.
I even have an entry in my hosts-file for
<myInternalIp> <servername>.<domain>
- Do I have to specify the domain explicitly in addition when integration the WD4A applications in the portal?
- Is there a correlation between the Portal Event namespace, the namespace of my iViews and page and the domain name of my server?
- Does the portal event namespave to have the prefix urn: or not?
Thanks again in advance

Safari routing not working

Hello all,
I have a very strange problem and I'm looking for suggestions. Recently, I tried using my work place VNP which I log into using a web browser. This event seemed to have completely broken safari.
At first I thought it was my routing table, but when I check it with netstat -ar, it looks ok. Nother weird. My other applications are still working (mail, iChat). Opera works correctly too, but Safari always tells me that I am not connected to the internet. I have tried restarting and Resetting Safari but so far that does not work. I searched my disk using spotlight for all the files that changed today and got rid of the safari related files but this does not work either.
It's a very strange problem and I'm looking for suggestions on what else to try.
Thank you in advance.

You're welcome. Sometimes the little things can be the most confounding.
Thanks for the and Aloha from Big Island.

Simple lan to lan routing (not working)

Similar Messages

Maybe you are looking for