Simulation Interface toolkit not working

I am working on a simulation and control problem using LABVIEW and Matlab. I have installed the simulation interface toolkit. But, the SIT server is not running. I have added the lines:
"addpath('C:\SimulationInterfaceToolkit'); NISIT_AddPaths; NISITServer('start',6011);"
in the matlabrc.m file. The NI SIT blocks are available in the simulink library. When I start matlab, the line:
" SIT: Added paths for Simulation Interface Toolkit 2011" appears. But the lines: "Starting the SIT Server on Port 6011 SIT Server started" don't show when matlab starts. I am attaching the Matlab startup screen.
Please help me out with this.
Thank You
Attachments:
Matlab Startup Screen.PNG ‏101 KB

OK I solved )))
Try the follwowing:
1- uninstall Labview and Matlab and the simulation interface toolkit (SIT) (be sure that u have only one version from SIT)
2- If you are going to use SIT 2011...then you will need Labview 2011 for sure and Maximum version of Matlab 2010 I think.
Revise the combatibility of SIT with Matlab on google
Be sure to use MATLAB 32-bit version
hope it will help
thanks
A.Hakim

Similar Messages

Simulation interface toolkit: SUB VI not executable error

Hi;
I have a real-time application where I model things in Simulink and use Simulation Interface Toolkit to carry out hardware-in-the-loop simulations. As a real-time target, I am using NI-PXI8106 with NI-PXI6251 DAQ card on it. Up until now, I was able to run my code just fine. However, for some reason, my vi didn't work today and gave several errors such as:
SubVI NI_SIT_sitclient.Lvlib:RVE.vi: SubVI is not executable
Details:The SubVI is not executable. You must fix all error in the subVI before this VI can run.
SubVI NI_SIT_sit Init Model.vi: SubVI is not executable
Details:The SubVI is not executable. You must fix all error in the subVI before this VI can run.
This is just few of many error that I received...In the details section of the error list window, the error statement are usually like the following:
SUBVI not supported for current target..
Type not supported in the current target...
The only thing that changed since the last time I ran this program with success is the IP change of the target machine..However, when I use Measurement and Automation tool, I am able to access my target machine (PXI8106) without a problem...Maybe there are some certain rules for IP settings on the PXI target? ...I can provide the details of my new IP configuration numbers if necessary...
I also reinstalled the SIT 5.0 on the target machine but It didn't do the trick. I am wondering if there is anyone out there who can help me out with this problem..
Thank you so much!
Kind Regards.

Hi there,
I was just wondering if you did manage to solve this problem. I'm a new user and have recently started using the Simulation interface toolkit. I have created my model using Simulink and used the real-time workshop to convert it to a .dll file. I tried to run it on labview and it seems to build it on the realtime target, however as soon as map it to the hardware (using a NI BNC-2111,It's just a bunch of analog inputs and output which I have connected to a voltmeter), a dialog box pops up with the the following error:
Error 1003 occurred during host VI initialization: SIT_test1.vi >> NI_SIT_sitclient.lvlib:sit Init Model.vi >> NI_SIT_sitclient.lvlib:sit Connect to Target.vi
<append>=========================
Simulation Interface Toolkit: The driver VI (SIT_Test_Driver.vi) is not executable.
Check the following:
1) You have not modified the driver VI.
2) You properly installed SIT and any necessary driver software on the target.
3) The target has not been locked from Measurement and Automation Explorer.
Do you want to launch the SIT Connection Manager dialog box and reconfigure the simulation?
Please look at the JPEG picture attached below to see how the error looks on my monitor.
Thanks
Attachments:
error1.JPG ‏135 KB

Simulation interface toolkit tutorial

I'm trying to perform the tutorial titled "Converting a Simulink Model into a Model DLL", found on p.22 the Simulation Interface Toolkit manual (http://www.ni.com/pdf/manuals/370420b.pdf).
It starts off by building a new Simulink model of a sine wave (p.9). On step 7 of that process, it mentions a "NISink" block from the "NI Toolkit Sinks" library in Labview. I do not see this library, and I got zero hits when I searched the libraries for "NISink". I do have a library callled "NI SIT Blocks" but it does not have a "NISink" block, only "SignalProbe", "SIT Out1", and "SIT In1".
I am using SIT V5.0 with Simulink V7.2(R2008b), but the tutorial appears to be a bit older, perhaps from SIT V2. I assume that "SIT Out1" has replaced "NISink" but, as a novice, assumptions bother me. Is there a more up-to-date users guide available? I found the "SIT 2009 Help" file online (http://zone.ni.com/reference/en-XX/help/371504E-01/) but the how-to's there do not contain any tutorials.

I found a help example that was installed on my system with Labview, obviously a little more up to date. It’s also found online here:
http://zone.ni.com/reference/en-XX/help/371504E-01/TOC5.htm
I ran through the help example for the SIT how-to "configuring a simulation" and it worked as expected. When I then proceeded to the "configuring a simulation on a real-time target", I found that tasks 1 and 2 were already complete and verified working from the first how-to. During task three, however, step 7 fails at compile time (see attached file matlab_output.txt)
It looks to me like it is mssing a header file from the Simulink Real Time Workshop (called rtwtypes.h). It contains declarations for some sized and unsized generic data types, including uint_T. However, that file is available in the regular RTW library directory. Not sure why I can use the SIT server in Simulink to control the s-function with LabView, but I can't build a stand alone DLL for a real time system.
Attachments:
matlab_output.txt ‏11 KB

No output from Simulink to LabVIEW with Simulation Interface Toolkit (0/1)

I'm able to send data from labview to simulink, but the labview
display doesn't show any output from the simulink model. I've attached
two very simple labview and simulink files which gives me this
problem. I have the same problem when trying to implement the sinewave
example in the manual for the toolkit as well.
I'm using LabVIEW 7.1 Pro, Matlab 6.5 and Simulink 5.0 on WinXP pro.

The Simulation Interface Toolkit 2.0.1 or earlier does not work with LabVIEW 7.1. There is a patch available (or available soon) from NI support that corrects this problem. THe patch is Simulation Interface Toolkit 2.0.2.

Reproduction of Simulation Interface Toolkit example

Hallo everyone,
in trying to reproduce the example found in the Simulation Interface Toolkit How-To I am facing an error with LabVIEW 2009.
I have succesfully created a host-VI working with the Simulink .mdl-file on localhost as Simulation Environment which runs well.
And I can succesfully compile the desired .dll-file (sinewave.dll) with Simulink and nidll.tlc.
But if I want to use a cRio-9024 as Real Time-Target with FPGA-Interface I get the following error when I start the Host-VI:
<<<
Missing Simulation Model File
The simulation file sinewave.out couldn't be found in the expected paths. Please FTP the file manually to your Real-Time system.
The following expected paths do not contain the simulation model:
C:\[...]\sinewave_nidll_vxworks_rtw\sinewave.out
C:\[...]\sinewave_nidll_rtw\sinewave.out
>>>
This is the resulting deployment status:
<<<
Initializing...
Calculating dependencies...
Checking items for conflicts. This operation could take a while...
Preparing items for download. This operation could take a while...
Deploying NI_FileType.lvlib
Deploying NI_SIT_util.lvlib
Deploying NI_LVConfig.lvlib
Deploying NI_SIT_Replay.lvlib
Deploying XDNodeRunTimeDep.lvlib
Deploying NI_SIT_Data Log.lvlib
Deploying NI_SIT_SITServer.lvlib
Deploying NI_SIT_driversupportVIs.lvlib
Deploying NI_SIT_ClientConnMngr.lvlib
Deploying NI_SIT_sitctls.lvlib
Deploying sinewave_Driver.lvproj
Deploying NI-Mess-Fix(successfully deployed target settings)
Deploying NI_SIT_Data Log.lvlib:Expand Signal Name.vi (7,85 K)
Deploying NI_SIT_Data Log.lvlib:Get Group Number.vi (4,46 K)
Deploying Set Bold Text.vi (11,92 K)
Deploying whitespace.ctl (2,09 K)
Deploying Set String Value.vi (5,06 K)
Deploying NI_SIT_Replay.lvlib:Wait for Ack.vi (5,50 K)
Deploying NI_SIT_driversupportVIs.lvlibIT Driver FP Strings.vi (2,31 K)
Deploying NI_SIT_driversupportVIs.lvlibIT Server Command.ctl (2,09 K)
Deploying NI_SIT_Data Log.lvlib:Enable Disable GPL Item.vi (13,12 K)
Deploying NI_SIT_Data Log.lvlibet Group Probe List Enabled Groups.vi (9,54 K)
Deploying NI_SIT_Data Log.lvlibet Group Probe List Logging Enabled State.vi (7,41 K)
Deploying NI_SIT_driversupportVIs.lvlibIT Timing Src.viNI_SIT_driversupportVIs.lvlibIT Timing Src.vi loaded with errors on the target and was closed.
LabVIEW: Failed to load shared library SIT_TimingInterface.*IT_InitTimingSrc:C on RT target device.
LabVIEW: Failed to load shared library SIT_TimingInterface.*IT_GenerateOneTick:C on RT target device.
LabVIEW: Failed to load shared library SIT_TimingInterface.*IT_ClearTimingSrc:C on RT target device.
Deploying NI-Mess-Fix Container
Deployment completed with errors
>>>
Why should I produce a file called sinewave.out? I don't think I really need it.
Can anyone please tell me how to employ the sinewave.dll properly so that it works on my cRio?
(I don't want to use hardware I/Os yet, just run the .dll on the cRio.)
The best help for would be a step-by-step description coming from a working VI which uses sinewave.mdl inside LabVIEW and having sinewave.dll ready for use.
Must I consider any other document to be able to finish this example?
Thanks for your effort!
Solved!
Go to Solution.

Hallo Marco,
thanks for your advice. I will give your hint a try.
But I wonder why I need an .out-file? Is the cRio 9024 device a VxWorks-based target?
Thanks for your help!
Jan

Required SW for the Simulation Interface Toolkit

Hello,
I would like to add a LabVIEW front panel to my Matlab/Simulink model. According to the data sheet, the following software is required for the SIT:
System Requirements
The LabVIEW Simulation Interface Toolkit requires that you have a
proper license for the following products:
• MATLAB® version 6.0 or later
• Simulink version 4.0 or later
• Real-Time Workshop® version 4.0 or later
• Microsoft Visual C++ version 6.0 and
• LabVIEW version 7.0 or later
To simply create a LV front panel for my model, do I still need to have LabVIEW installed? If so, which versions would be compatible?
I currently have the student version of Matlab 6.0 and Simulink 4.0. Will the SIT work with the student version?
If I only want to create a LV front panel, do I still need to have the RT Workshop or Visual C++ installed?
Thank You,
Mike

Greetings!
Yes, you are required to get the sw as mentioned.
To simply create a LV front panel for my model, do I still need to have LabVIEW installed? If so, which versions would be compatible?
Yes, to create a LabVIEW user interface / front panel, LabVIEW is required. LabVIEW 8.2 is the latest version.
The Simulation Interface Toolkit (SIT) 3.0.2 updates SIT 3.0.1 to support LabVIEW 8.2, the LabVIEW 8.2 Real-Time Module, and the LabVIEW 8.2 FPGA Module. You also can use SIT 3.0.2 with LabVIEW 7.1.x or with LabVIEW 8.0.x. However, you cannot install SIT 3.0.2 for more than one version of LabVIEW on the same computer.
2. I currently have the student version of Matlab 6.0 and Simulink 4.0. Will the SIT work with the student version?
The MathWorks, Inc. MATLAB® / Simulink® application software R2006a.
The MathWorks, Inc. Real-Time Workshop® R2006a.
Support for The MathWorks, Inc. MATLAB® / Simulink® application software release 13.x or 14.0, 14.1, 14.2, 14.3
If you install SIT 3.0.2 for LabVIEW 7.1, you can use Microsoft Visual C++ 6.0 to convert models to model DLLs. If you install SIT 3.0.2 for LabVIEW 7.1.1, 8.0, 8.0.1, or 8.2, you can use either Visual C++ 6.0 or Visual C++ .NET 2003.
If you installed more than one version of The MathWorks, Inc. MATLAB® / Simulink® application software, SIT installs support only for the latest version on the computer.
You want to make sure the Matlab release is one amongst the above.
3. If I only want to create a LV front panel, do I still need to have the RT Workshop or Visual C++ installed
RT Workshop comes with SIT. You will have to get Visual C++ and use that compiler.
Thanks and hope this helps
Best regards
Avi Harjani

Simulation Interface Toolkit

Hello,
I'm using the Simulation Interface Toolkit 3.0 because I want to control a Simulink model in LabVIEW 7.1. For instance, I want to generate a sine wave using a constant block. In this manner I can provide to my Simulink model every kind of signal without changes in it.
To perform this task Simulink needs an input value at each integration step.
I would to know if this task is achievable and if someone could tell me something about the communication between LabVIEW and Simulink.
Thank you for your help!:smileywink:

Hi Alessio,
Maybe you have the solution to my problem:
I have a Simulink model that works with a LabVIEW VI using the Simulation Interface Toolkit and the SIT server.
In order to use this model and this VI without Simulink, I created a dll (nidll) of my Simulink model like shown in the following manual:
http://www.ni.com/pdf/manuals/370420b.pdf
By doing so, LabVIEW automatically created 6 VIs that should work with my model DLL.
My questions are:
- Can I use the VI that I previously made for my Simulink model with the model dll ?
- If yes, How ?
- If no, How can I use my model dll and these new VIs?
Thanks in advance.

Simulation Interface Toolkit 4.0 cannot map to indicator

I have LabVIEW 8.5, SIT 4.0 and Matlab R2007b which uses Simulink 7.0. NI has a manual and example for using the Simulation Interface Toolkit at http://digital.ni.com/manuals.nsf/websearch/679117802743CC128625732B00697485 I can map control signals just fine between LV and Simulink but when I try to connect an indicator such as a Waveform Graph or numeric indicator to Port 1 of a Simulink object like a Sum block or Sine Wave (as the example shows) it always says that the mapping is invalid and greys out the box. It seems like there is a bug here because this should just work. Port 1 of a Sum or Sine Wave should be its output as a scalar. Anyone that uses the SIT have any ideas?
I've attached the help file with example that I followed.
Message Edited by tmar89 on 05-22-2008 04:04 PM
Attachments:
lvsimtkhowtoconcepts.zip ‏163 KB

Here are some screen shots from the Simulink model to the VI and error.
Attachments:
ss3.png ‏13 KB
ss1.png ‏13 KB
ss2.png ‏30 KB

Error 1092 happened while running the executalbe file from an example code of Simulation Interface Toolkit

With Simulation Interface Toolkit 3.0.1 and LabVIEW 8.0, I built the example code Sine Wave.vi to be an executable file. I made no modification to the code except setting Real-Time Target to be localhost in SIT Connection Manager. Everything was OK during the building process. But when I run it, error 1092 was reported. Here is the error message.
Error 1092 occurred at Invoke Node in sit Traverse.vi->sit Traverse for References.vi->sit Find Object By Label.vi->sit Get RPS-Control-Indicator Refs.vi->sit Init Model.vi->Sine Wave.vi (Traverse Initialization Failed)
I cannot find out any helpful information about this error code. Can anybody help me? Thanks a lot!
帖子被zhuang在09-13-2006 08:01 AM时编辑过了

To my knowledge, building an EXE out of a SIT host VI is not supported. The SIT host VI utilizes functionality in LabVIEW that is not exposed in the LabVIEW Runtime Engine (i.e., with built EXEs and DLLs).
-D
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Simulation interface Toolkit을 깔아도 matlab에 블록이 다 생기지가 않습니다.

Simulation Interface Toolkit 3.0을 사용하고있고 LabVIEW 7.1을 사용하는 유저입니다, Matlab 6.5.1을 사용하고요
모터컨트롤을 하기위해서 미리 시뮬레이션을 하기위해 위의 툴킷을 사용하여 시뮬레이션을 해보려고하는데
Matlab의 Simulink블록에서 ni_sink블록과 XY_sink블록이 생기지 않아서 문제입니다.
어떻게 해결책좀 알려주세요

Simulation Interface ToolkitのNISink要素とは?

Simulation Interface Toolkitを購入させていただきました。
以下、使い方に関する質問です。
http://zone.ni.com/devzone/conceptd.nsf/webmain/955A9D79583A0AB686256DB8006672B8
を拝見しながら、使い方の勉強をしておりますが、その中で示されている
NISinkというSlimulink要素が見つかりません。
添付の画像ファイルにみるように、SITのインストールは正しく出来ている様ですが
（Matlab opening.GIF）、Simulink Libraryの中に、それらしきものが
見つかりません（Simulink Library Browser.GIF）。
なお、利用しているシステム構成は、
LabVIEW8.0
Simulation Interface Toolkit 3.0 + パッチプログラム
Matlab7.1
Windows XP professional SP2
です。
以上よろしくお願いします
山本正樹
添付:
Matlab opening.GIF ‏33 KB
Simulink Library Browser.GIF ‏27 KB

山本様
日本ナショナルインスツルメンツ技術部の長久です。
＞ご提示いただいた英文情報（Can I Run a SIT VI Stand-Alone in Windows?）は、
＞「②のケースでRealTimeターゲットを使わない実験ができるか？」ということでしょうか。
英文の情報は、ハードウェア制御を行う②のケースをRealTimeターゲットデバイス上ではなく
LocalHostにて行うものとなります。ただし、この方法でVIを作成するには、LabVIEW Real-Timeモジュールは
必要になります。
DAQボードはSimulinkモデルから作成されたDLLを使って制御いたします。よって、DLL
を使用しないシュミレーション環境（ケース①）ではDAQボードを使用した実験はできません。
＞「SIT connection managerのコード自動生成機能を用いて、SimulinkモデルをDAQへ
＞接続することが可能か？」
Simulinkモデルを直接DAQへの制御へ接続することはできません。
ケース②の方法は、RealTime-Workshopを使用してDLL化されたSimulinkモデルを
DAQのI/Oへ割り当てるものとなります。
RealTime-Workshopはお持ちではないのでしょうか？
SITを使用して弊社のハードウェアにてSimulinkモデルを実装いただくには、
SimulinkモデルがDLL化できるRealTime-Workshopが必要になります。
以下に必要製品をまとめました。
SIT connection managerのコード自動生成機能を使用するには以下の製品が必要になります。
RealTime-Workshop (Mathworks社の製品)
LabVIEW Real-Timeモジュール
LabVIEW シミュレーションインタフェースツールキット

Midi usb interface will not work after installing os x mavericks

Installed os x mavericks and now my tascam us-144 mkll midi interface will not work and driver will not install . I plug the interface in to another computer and it works fine so i know its not the interface or cable . It worked fine before i upgraded to os x mavericks , any ideas ?

Ya , went on tascam website and found out none of there us drivers are compatible with mavericks . They say there working on a fix .... thanks for a respnse though

Simulation Interface Toolkit - How to toggle a manual switch in simulink from LabVIEW?

I have a manual switch in my simulink diagram that I want to use to switch between to values from my LabVIEW interface. I have tried to connect a toggle switch at LabVIEW`s VI with different parameters in the simulink model(I can choose betweenhow Port Labels, sw, and action), but none of them seem to work properly.
The manual switch in Simulink gets to inputs, one output. There is also an Environment Cotroller that output the simulation(SIM) or Real-Time Workshop(RTW) port depending on the current environment.
At this time I am doing simulations and are not using Real-Time Workshop.
I want to thank you for your help in advance.
-Mari

Hi
Kotsya,
Thank you for posting to the National Instruments Discussion
Forums.
If you are not using the Math Interface Toolkit, you may be
interested in using the MATLAB® Script Node. This allows
you to call MATLAB® commands using ActiveX and I you
can call your Simulink model from MATLAB® that way.
Here are some resources on how you can do this:
MATLAB® Script Node LabVIEW 8.2
Help
How Can I Resolve MATLAB® script node and
Xmath Script Node Issues in LabVIEW?
Hope this helps!
Abhinav T.
Applications Engineering
National Instruments India
LabVIEW Introduction Course - Six Hours
Getting Started with NI-DAQmx
Measurement Fundamentals

Erlang: wx graphical user interface does not work in R16B-1

After upgrading erlang to R16B-1, the wx GUI subsystem does not work anymore.
1> wx:demo().
ok
=ERROR REPORT==== 5-Mar-2013::23:13:11 ===
ERROR: Could not find 'wxe_driver.so' in: /usr/lib/erlang/lib/wx-1.0/priv
Should I install some additional package that was not required before?
Or is this a bug with the new version?

This seems to be a bug with the new version.
See also: https://bugs.archlinux.org/task/34201
Last edited by xyproto (2013-03-08 19:59:03)

Transmission torrent web interface pc not working

This never bothered me before as I have quickly found a work around for this but I have always wondered why this doesnt work for me.
I cant seem to get the torrent app to fully load. it just seems to not load all the way.
So I only see this,
and it never advances from there.
Like I said I found workarounds were i can see torrent downloads from web apps like: Android, Xbox 360, and Xbox one. But none of my PCs can display it properly.
Any help From somome that has figured this out to display properly would be appriciated.
Nas info:
EZ Media and Backup Center 2TB
Version:4.1.104.31360
Transmission Torrent: 4.0.30086

Hi Wicked.. well.. the answer i'm about to give you, you will not like because i didn't like it either and has similar issues that you were having.
I have a the ix4-300D and had transmission working just fine on my NAS and then did an update to the firmware in early 2014 that basically broke transmission. Mine didn't even start or load any web interface. I tried everything including: reseting of web configuration of Nas (holding reset button), uninstalling and installing of transmission app (mine wouldn't even reinstall) and finally even backuped all data to external storage and full wipe of drives and nas config but sitll no go...
I was then forced to call Lenovo (i am still under support/warranty). They then sent me a link to a previous firmware version and a usb disk imaging image/tool that i then basically restored the default image and then upgraded to the latest firmwares and since then have not had any issues.
Twonky settings now save when changed in the web interface too! however migrating 10+ TB of data to 5-6 external hdds IS NOT FUN!
hope that helps buddy!

Simulation Interface toolkit not working

Similar Messages

Maybe you are looking for