Since IOS 4.3.3 My Ipod Touch 4th Gen 64GB fully discharges on standby in less than 6hrs with no apps running. How can I fix it?

I've followed all the suggestions for saving the battery life but the battery still discharges very quickly. The only way I can stop it discharging is by turning the ipod off, which sort of defeats the object!
It's been suggested that I totally reset the ipod as new and then set it up again from scratch. Does anyone now how likely this is to help, as it will take rather a long time?

Looks like good news!
I finally bit the bullet and did a reset as new.
It was a total pain as you can imagine, but it wasn't the end of the world to go through i-tunes reselecting the apps etc to sink (it was actually a pretty useful exercise because my ipod was full of apps I didn't really use!).
Anyway, it's been off the charger now for nearly five hours and I've been using it for bits and pieces like, the calculator, internet search over wifi, map viewing etc. and the battery is showing 97%!!! All setting are as per the default start up. I haven't changed brightness or anything like that.
Interestingly, now when it goes into standby, the router shows that the wifi link has dropped. When I then wake it again the link restarts after a few miliseconds. This didn't used to happen before.
I'm keeping my fingers crossed and will see how it goes over the weekend and report back on Monday!

Similar Messages

  • I have and ipod touch 4th gen that has the white screen of death but my home button doesnt work. how do i reset it?

    i have and ipod touch 4th gen that has the white screen of death but my home button doesnt work. how do i reset it?

    Restore, if iTunes will let you.  Everything except the password will be restored.  Connect via cable to the computer that you use for sync.  Be forewarned that it takes a long time.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here.

  • My iPod touch 4th gen. Keeps giving me the error message "cannot connect to the app store when I sign in. I can open the app store and browse it but I can't download anything. I have full signal strength with my wi-fi and safari is working perfect.

    My iPod touch 4th gen. Keeps giving me the error message "cannot connect to the app store when I sign in. I can open the app store and browse it but I can't download anything. I have full signal strength with my wi-fi and safari is working perfect. I turned it off and restarted it 3 times now. I have an iPad 2 and the app store works flawlessly with it. What is going on?

    Same here on my lpad2. Can access the web just fine from browsers but cannot install new apps or updates in appl store.  Seeing a few others reporting same issue tonight so likely an apple server issue and staff will notice it in network monitors and fix it...sometime this weekend.
    Rob

  • My iPod touch 2nd gen keeps turning the volume down automatically when i am doing things on it how do i fix it

    my iPod touch 2nd gen keeps turning the volume down automatically when i am doing things on it how do i fix it?  This happens when using the volume control buttons and the volume option in settings.  It keeps turning itself down to silent.  Any ideas?

    ?

  • My iPod Touch 4th gen is disabled for 22,000,000 minutes. I remember the passcode, and I can't restore.

    My iPod Touch 4th gen is disabled for 22,000,000 minutes. I have looked all around the Apple support communities and I always find the same "solution", which is to put it into DFU or recovery mode and restore from a backup. Here's my problem: My computer crashed awhile back and I had to completely start over from scratch. So, unfortunately, a backup of my device no longer exists on this computer or any other computer.
    Is there any way I can simply get rid of the disable? I remember my passcode, so that isn't a problem, all I need is to be able to input my passcode.
    Or, do I absolutely have to restore to factory settings, and lose all my data?
    By the way, I hope it does not matter, but I can't remember the IOS is was last updated with.
    Thanks.

    Disabled
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                         
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up     
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload most iTunes purchases by:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store        

  • IPod Touch 4th Gen 64Gb EXTREAMLY slow to sync

    My iPod Touch 4th Gen seems to have, in recent weeks, slowed down syncing. I have made no changes, and only use it for music, yet when new music goes on, it takes around 1.5mins per track to sync. The files size per track is the 5MB (192kbps MP3). So I am a little stumped as to explain why it is being so slow, and I do not have time to restore if I am to get the tracks back onto the iPod before I go away on a 2 day course tomorrow.
    Sync over USB, iOS 6.0.1, iTunes 11.0.1.12
    Any ideas, please tell me.

    Now it's doing it with all my music.I have reset the iPod,restored to a back up and even to factory setting and it's still doing it.my mates iPod still has 4.3.5 and the album plays only one song but mine wants to play 2songs at the time it only stated doing this after the iOS 5 update  I kept a back up of my iPods 4.3.5 on a USB hard disk if I restore to iPod to that back up will the iPod go the 4.3.5?

  • How to fix the iOS 6 artwork mess on iPod Touch 4th Gen? I'm desperate now!

    Okay. So this has been going on for a while and I've finally reached a dead end. Since the update to iOS 6 my musical updates to my iPod Touch have been painful and annoying. Whenever I try to upload new songs to my device, almost everytime iTunes fetches the wrong artwork for them. Basically, I manage my iPod manually by draggind and dropping. Before I upload new songs I use MediaMonekey to add artworks to the ID3 tags. This has worked like a charm for years. Until the dreadful iOS 6 update came out. Since then in order to get the correct artwork I had to upload and delete the songs or albums several times before iTunes could get them right. There came a point when I became too frustrated to do this every time I updated my library, so I decided to look for a solution. I googled my issue and found out that I was not the only one with it. The most common solution was to get all of your library wiped out and then reupload it again or something like that. I was desperate enough to try it. To my dismay, it did not work. Even when everything was wiped off, iTunes still managed to get half of the artwork wrong for the songs I uploaded.
    So, I come here, hoping that someone will be able to offer a solution that will be able to make me manage and update my library like I used to without any hiccups.
    Thanks in advance to everyone that responds!

    Confirm that you have the latest version of iTunes.  It's 11.02 for the Mac.  I don't know about Windoze.
    Try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here.

  • HT5192 Can't install ios 5.1 on my ipod touch 4th gen

    Unable to install IOS 5.1 update on my ipod touch 4G. On error occurred while installing. I'm using my ipod only to update it.. How can i install IOS 5.1 update on my ipod touch 4G without encountering any problem?

    Check out the other ios 5.1 installation error posts, using search terms like "can't install ios 5.1." I found one that helped me. There are several fixes that appear to work, such as changing your DNS #'s on your device, rebooting your device and trying again, and so on. Personally, I have the same device as you and I restarted the device. Then I installed 5.1 from the device. It didn't work from my Mac previously, but it worked from the device. I did have to download it first on the Mac, but once downloaded you have the choice to install from your device as well (if you have home sharing turned on between your Mac and iPod). I had a "1" under updates on my iPod (which was for the firmware update). I just chose to update from the iPod and it worked.
    If you don't know how to do a reboot of your iPod, just hold the power and home buttons in until you see the Apple logo. Then you can let go and wait till it reboots.
    Hope this helps.

  • HT201263 iPod touch 4th gen is stuck in recovery mode and won't restore with iTunes. Please Help!

    I had jailbroken my ipod touch then decided it didnt do much of anything, so I decided to restore my ipod. But itunes didnt finish the restore and left me in recovery mode. Now it says iTunes has detected an ipod in recovery mod, but when I try to restore it, it says something like could not connect to apple restore firm and I'm back to square one.
    Any Help is appreciated!

    Jailbreaking
    Jailbreaking voids the Apple warranty and also means that you will not get any support from Apple, including from this Apple forum. Jailbreaking can't be discussed in this Apple forum.
    Unauthorized modification of iOS has been a major source of instability, disruption of services, and other issues
    Try DFU mode and then restore
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    Try on another computer

  • My ipod touch 4th gen has got discharged and is not working even though i have kept it on charging and have also tried the reset method by pressing the home and power on/off button together..what else can i do to start it? please tell !!

    please help me!

    - Have you tried anther cable and charging soruce?
    - Have you connected the iPod to yur computer?  If iTunes sees the iPod, restore the iPod via iTunes-
    - Next see if see if placing the iPod in recovery mode will allow iTunes to see the iPod so you can restore the iPod. For recovery mode:
    iPhone and iPod touch: Unable to update or restore
    - Last, make an appointment at the Genius Bar of an Apple store.

  • I updated my ipod touch 4th gen 64gb to ios6 and everytime i go into music the screen goes white then crashes! whats going on?

    I cannot access my music on my ipod after the latest update, no idea why or what to do! Can anyone help?

    Try the following:
    - A reset. Nothing is lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory settings/new iPod.
    If you still have the problem that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order

  • Shouldn't iOS 7 release on the iPod touch 4th gen and iPhone 3GS because of an iOS bug involving faulty/generic chargers?

    Someone should tell Apple about this because the bug is still in iOS 6 but reportedly is fixed in iOS 7 beta 4 or 5

    Why don't you?
    Send the information to http://www.apple.com/feedback/iphone.html
    Allan

  • My ipod touch 4g fell in water and it works well however the camera shutter won't work how can I fix this?

    The question explains all

    If it is not completly dry then try it.
    Next
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                       

  • IPod Touch shows up on My Computer, but freezes iTunes, and does NOT show up on iTunes, how can i fix this?

    I have honestly spent countless hours trying to fix this, I FINALLY got it to show in My Computer, driver is updated, I have re-installed iTunes numerous times, recently did a FRESH Windows 7 Ultimate re-install, i can't restore the iPod (because it has been restored, and I can't even access it via iTunes) My iPod is NOT broken, it works on my laptop fine, it shows up on iTunes and My Computer, no problem. However, I need to use my iPod on my main computer for songs (iPod's practically new by the way) Like my question states, my iTunes freezes up, and it's very strange because it freezes, then a couple minutes later iTunes works fine, BUT my iPod doesn't show up on the side like it's supposed to. I've done everything, I hope I get some good support, thanks in advance!
    ~Thomas
    Edit: I have the latest update for the driver, and iTunes, iPod has 4.3.3
    Message was edited by: Havocks

    http://support.apple.com/kb/TS2972

  • Hey Guys I have an iPod touch 4th gen I updated some games on the computer and I synced the apps but it still won't come up on my iPod D; anyone got helpful comments or solutions?

    Please reply ;3

    No nothing like that and I just noticed it did update because I just got to my pops I don't have Internet at my house and it suddenly appeared when I arrived about half an hour ago but I didn't noticed it do you think I have to have Internet to play newer. Versions?

Maybe you are looking for

  • After Windows 7 update DRVLOAD.EXE error

    Hello, I have a problem. After an automatic update from the Microsoft site is my Windows 7 Home Premium not running anymore. At startup the following appaers: the error x: \ windows \ system32 \ drvload.exe and will not start up. I can not bring him

  • Link to a SAP transaction in the body mail using SO_NEW_DOCUMENT_SEND_API1

    Hi everyone, Is it possible to set a link to a text in the body of a mail sent by SO_NEW_DOCUMENT_SEND_API1, in order to navigate to a SAP transaction? Example: Body (in sbwp): Distribution done. Click  here for going to transfer program. And the lin

  • Service Call with Expenses Report

    Dear All I would like to view a service report with the expenses , may I know how to get this report from SAP B1? Thanks in advance for advice. Thanks, Catea k.

  • Adobe Media Server Installer does not run

    I am trying to install Adobe Media Server 5 on Windows 2008 R2 64 bit on i3 logged in as an administarive user over RDP. The installer simply does not run - a very short hourglass then nothing.  Not logs in applicaiton, system of setup logs. The bund

  • Authorization at Weblogic 10.3.4/5

    I deploy an application which has lots of web pages. Page 1: login Page 2: product list Page 3: staff list What I want to do is setting new authorization. Staff A, B, C can login to this application. Staff A can view Page 1 and 2 Staff B can only vew