Since last Airport Update, Airport Express no longer connects to network

I Just get a flashing amber light.
I have hard reset and gone through the step by step, and all I want to do it use it for a remote printer.
I cannot even see the thing now.
Can anyone help ?

Not sure how you're resetting but try this...
Reset the Express back to factory defaults:
Use a pen or a paper clip to press and hold the reset button until the
status light flashes quickly (about 5 seconds). The following will occur:
AirPort Express restarts with the following settings:
AirPort Express receives its IP address using DHCP.
The network name reverts to default Apple Network.
The AirPort Express password is reset.
After you reset the express, airport utility should see the express with the default name. Double click the express and configure manually, the airport utility should tell you that you are switching networks, switch to the express network then continue with configuration and set the WEP key the same as the Extreme.

Similar Messages

Airport Express G cannot connect to network

Hello,
I have the Airport Express (G version) running the 6.3 firmware. My problem is that I cannot connect to my home network. When I use the airport express to create the wireless network, I can connect the Windows and Mac machines to it to stream iTunes and all works perfectly. When I connect it to my home network (Linksys WRT54G running dd-wrt) I cannot connect anything to it once it is configured. I set it up from the mac and all the network settings are transferred to the Airport Express. It seems to connect for a minute then the connection drops. Sometimes iTunes sees the Airport Express and it tries to connect but is unsuccessful. I cannot edit the airport settings from either machine without resetting it to factory defaults and reconfiguring.
The problem seems to be the Airport Express doesn't want to play nice with the home network. Does anybody have any suggestions?
As I am writing this I cannot remember if I have had the Airport Express working since I've installed dd-wrt. I know it worked pre dd-wrt and am hoping that isn't the issue.
Thanks in advance for any help.
Jared

Express works fine with third party routers including the WRT54G, but once you modify it you're on your own. I'd go to the dd-wrt forum and ask around.

I recently installed itunes update and can no longer connect to network nor internet

I recently (sept 2013) installed itunes update and can no longer connect to a network nor internet wired /wireless. I know it is not the gateway as other devices work. Please help. I am not very knowledgable so exact instructions will be most helpful.

Try connecting your computer/laptop directly to the base station with an ethernet cable to one of the external ports and install your network settings. If it finds it there, it will find it after you've reloaded your network info to the base via the Apple Utility. Hopefully when you disconnect afterward, all will be fine. Be sure not to select "closed" network although Macs will login with no prolem, PC's have trouble doing so even with the network data stored in the internet settings.
Good luck!

Airport Express no longer connects

Initially my airport express worked great, however, it no longer is able to resolve an internet connection - can't find a DNS server. My iMac with Snow Leopard has a similar issue with the internet (it will work for a few seconds, then stop completely loading pages). However, my older macbook with leopard has no problem when connected directly with ethernet. Has anyone experienced any problems like this before? It's driving me a bit crazy!

it simply keeps asking me to run dx and then offers no real information
What information does it offer?

Since last leopard update, i can no longer see my external hard drive

After last leopard update my external hard drive is no longer visible on the desktop, tried connecting to the laptop but this has also had the same update and the same problem, any ideas??

Open Disk Utility, select the External Hard Drives first icon in the list of Drives, click the Repair Disk button.
Dennis

Airport Express working, PC connects to network but cannot use internet

I set up my Airport Express wireless network, and all is functioning. My IMac recognizes and uses the network. My PC laptop recognizes the network (excellent signal) and "connects" or indicates that it is connected, but I cannot access the internet. Have tried the power-down and re-booting sequences suggested in other posts. Does the PC just not work on a Mac wireless network?
Thanks.

Ok, time to use the Ping tool for some additional troubleshooting. We will need to open another command window.
1. Ping the loopback address to verify that TCP/IP is installed and correctly configured on the local computer. To do this, type the following command: +ping 127.0.0.1+
If the loopback test fails, the IP stack is not responding. This problem may occur if any one or more of the following conditions is true: a. The TCP drivers are corrupted, b) The network adapter is not working, or c. Another service is interfering with IP.
2. Ping the IP address of the PC to verify that the computer was correctly added to the network. To do this, type the following command: +ping 10.0.1.3+
If the loopback test succeeds but you cannot ping the local IP address, there may be an issue with the routing table or with the network adapter driver.
3. Ping the IP address of the default gateway to verify that the default gateway is working and that you can communicate with a local host on the local network. To do this, type the following command: +ping 10.0.1.1+
If the ping fails, you may have an issue with the network adapter, the router or gateway device, the cabling, or other connectivity hardware.
4. Ping the IP address of a remote host to verify that you can communicate through a router. We did this earlier when you attempted to access Google through the web browser using Google's IP address. This time, we will try it via the Ping tool. To do this, type the following command: +ping IP address of remote host+
If the ping fails, the remote host may not be responding, or there may be a problem with the network hardware between computers. To rule out an unresponsive remote host, use Ping again to a different remote host.
5. Ping the host name of a remote host to verify that you can resolve a remote host name. To do this, type the following command: +ping www.google.com+
Ping uses name resolution to resolve a computer name into an IP address. Therefore, if you successfully ping an IP address but you cannot ping a computer name, there is a problem with host name resolution, not with network connectivity. Verify that DNS server addresses are configured for the computer, either manually in the properties of TCP/IP, or by automatic assignment. If DNS server addresses are listed when you type the ipconfig /all command, try to ping the server addresses to make sure that they are accessible.
If you cannot use Ping successfully at any point, verify the following configurations:
o Make sure that the local computer's IP address is valid and that it is correct on the General tab of the Internet Protocol (TCP/IP) Properties dialog box or when it is used with the Ipconfig tool.
o Make sure that a default gateway is configured and that the link between the host and the default gateway is working. For troubleshooting purposes, make sure that only one default gateway is configured.
o Make sure that Internet Protocol security (IPSec) is not turned on. Depending on the IPSec policy, Ping packets may be blocked or may require security.
(Important: If the remote computer that you are pinging is across a high-delay link such as a satellite link, response may take longer. You can use the -w (wait) parameter to specify a longer timeout period than the default timeout of four seconds.)

Airport Express failure to connect to network

My new airport express will not join the wifi network at a Kimpton Hotel. It is incapable of giving any clue as to it's problem other than that the error is "unexpected" thus I have no idea what to do. CAn anyone throw sone light on the subject?
Oliver

Yes, there's an exception for Bonjour in the firewall (Bonjour is allowed)
I've try to re-add the "APAgent" which control Airports and restart the firewall but it didn't worked...
The only solution I've found was to desactivate Windows firewall...
(Firewall of my ADSL box is activated).
Maybe I should try to repair iTunes Installation like WPLU...

Configurator, iPads update iOS will no longer connect to network

Managing 30 iPad 4s with Bretford cart, Mac Mini.
On a recent update to iOS 7.0.4, it seems that not all of my iPads took it nicely. Only 3 worked like I expected in fact, and function as they did before. 27 others will no longer connect to the network I had deployed as a package in Configurator. In fact, they went back to the beginning welcome / setup screen for the OS reload.
Is there something that I can try before I just set these all to erase and re-prepare them?

Update: I unplugged all, and manually plugged in one iPad.
I unsupervised, and prepared it again, reloaded all the apps, and got the same result.
Once the iPad shows up in Configurator as prepared, and in my supervised list, it seems good to go: BUT
as soon as I turn it on, it shows me the "Hello" welcome screen, asks to join the network, and seems to freeze. The iPad goes to sleep without it receiving a connection.

Since installing the last Firefox update I can no longer connect to some chat rooms, specifically Recon chat, though this still works in IE

I can load Recon as normal, and when I select Beta Chat, another tab opens and the logo appears. But this is as far is it gets.
This began immediately after the the update before the most recent (v3.6.12). I was hoping that this latest update today would rectify the problem, but it hasn't.

It doesn't say, but I think it's likely. However I use several other sites with Java chat, and they work perfectly, and I do allow all the regular updates of Java.
I had a look at the link you gave, but I couldn't find anything when I searched "Next Generation Java Plug-in 1.6.0_15". Should I just download a completely new exe, and would I need the two optinal files for kernel and online installation?

Airport Express won't connect to network, blinking amber light, and "unexpected error occurred."

I have two aiport expresses - both have the problem. Both continue to have a blinking amber light, when I go through all the setup activities, after completing the factory reset multiple times, I simply get "An unexpected error occurred."
In fact after I do this, my laptop has issues connecting to the network. I have Verizon Fios, not sure if that means anything.
Haven't seen this covered in any of the troubleshooting materials; they just keep going to factory reset to solve all problems, which I've done several times with each device to the same end.
Any ideas?

Hi - You can install 5.6 on Mountain Lion but it is tricky - here are instructions from a post by guru Bob Timmons -
The workaround is to use a utility like Pacifist to manually extract the application and then manually install it in the Utilities folder - see this link:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html
Another workaround....if you have Time Machine backups.....is to back in time to locate AirPort Utility 5.6 and restore it to the desktop. Then drag it into the Utilities folder.

My airport express no longer shows up in Airport Utility since I got a new router.

Hi all, I'm scratching my head at this one.
For years I've had an Airport Express and it has worked fine. I was using it simply to stream music from iTunes on my PC as well as my iPhone and iPad to my home theater which is in a different room. I had a Linksys WRT150N wireless router, and the Airport Express would join my existing network and stream music via Airplay.
A few days ago I replaced my Linksys router with a Netgear WNDR3800, and the Airport Express no longer connected. I assumed I had to set it up again, but it is not even recognized by Airport Utility, so I can't get to the setup screen. I tried performing a soft reset, hard reset, and attaching the Airport Express to one of my Netgear's LAN ports via Ethernet cable, but it still won't show up in Airport Utility. The amber light just flashes on the unit and I can't access any setup screens.
Am I missing something obvious? All of the help tips assume the Airport Express at least shows up in Airport Utility. In my Airport Utility there is nothing to select and it says "AirPort Utility was unable to find any AirPort wireless devices. Make sure the AirPort wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
I am running a PC with Windows 7 and using Airport Utility v. 5.6.1 for Windows.
Thanks for any help!
-Rob

Did you try temporarily connecting an Ethernet cable from your PC to the AirPort Express to see if AirPort Utillty could "see" the AirPort Express that way? This method will work virtually all of the time unless the Windows Firewall or the PC's anti-virus program is blocking the connection attempt from your PC to the AirPort Express.
If you want to configure the Express using wireless only, you need to remember that when you reset the Expess back to default settings, it is now producing a wireless network with a name like Apple Network xxxxxx.
You must log on to the Apple Network xxxxxx wireless network first....no password is required.....and then open AirPort Utility so that your PC will establish a connection to the AirPort Express.
Once the AirPort Express has been configured to join your Netgear wireless network, you can log back on to your normal wireless network and all devices will be working with one another.

Airport Express no longer joins network

Greetings, I have a cable modem internet connection; I use an older Airport Extreme (802.11n, without Time Capsule) to make a local wifi network with WPA2 Personal security, and an older Airport Express (802.11 b/g, firmware 6.3) to connect a laser printer in a different room.
All was working well until two days ago when access to the internet disappeared. I reset the modem, confirmed that the cable connection was working by plugging a laptop directly into the modem by ethernet, determining that the problem was the Airport Extreme. I discovered the 7.5.2 firmware update which I uploaded, and all seemed well.
However, the 27" iMac upstairs only connected to Airport intermittently; it appeared to have been duplicated in name, as well as only recognized the Airport Express. I've since been able to correct that problem, however, now the Airport Express no longer connects to the Airport Extreme network.
I've tried soft resets (unplugging then plugging back in) and hard resets (pressing the reset button with a paperclip until the amber light flashes, then reconfiguring the device). I've tried setting the Airport Express both just to join the network (printer sharing) as well as extend the network; I also reverted the Airport Extreme's firmware to 7.4.2 which works perfectly well. However, now after each successive attempt to reconfigure the Airport Express to join the network, Airport Utility says that the Airport Express has been successfully updated and will restart, which it never does - it simply flashes an amber light, and Airport Utility eventually times out and says that it was unable to find the Airport Express after restarting, noting that the settings have been successfully updated, but that there is a problem re-joining the wireless network/finding the device. Notably, the Airport Express no longer appears in the left hand list of wireless devices in Airport Utility.
Help!!

Hi pslebow,
You make it sound like there was no change, then suddenly the Airport Express 802.11g lost connection to the wireless network and you can't get it back.
What network security is your wireless network using?
From the specification sheet, "…When joining an existing wireless network, AirPort Express only supports WPA-Personal."
AirPort Express - Technical Specifications
Please make sure your router security is set to match.
iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support
If you have older Wi-Fi devices on your network that don't support WPA2 Personal (AES), a good second choice is WPA/WPA2 Mode (often referred to as WPA Mixed Mode). This mode will allow newer devices to use the stronger WPA2 AES encryption, while still allowing older devices to connect with older WPA TKIP-level encryption. If your Wi-Fi router doesn't support WPA/WPA2 Mode, WPA Personal (TKIP) mode is the next best choice.
Best,
Nubz

My ipad2 will not connect to network since last iOs update.

My iPad 2 will not connect to network since last iOs5 update.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

My new airport express does not connect my printer to my computer? My old airport did! then I updated to OS 10.9.2. How do I get it connected?

My new airport express does not connect my printer to my computer. The old airport did. I recently updated to OS 10.9.2. I have since bought a new
HP 6700 all in one wireless printer, got the latest Comcast router. None of which connect to my computer wirelessly. Which do I throw away the printer, router, or Mac? Help

Contact HP for support.
Explain that you are using a Mac, anticipate the inevitable groan, and wait patiently for their resident Mac expert to return from vacation.
Until then download and install its driver here: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=5058338&cc=us&dlc=en &lc=en
Otherwise return the printer and purchase one from a company that visibly supports OS X. HP isn't on that list.

HT3819 Since the last AppleTV update I can no longer use home sharing. chI have checked all IDs, rebooted iTunes, AppleTV, and my router, eck port settings in my firewall. Nothing works. Is it me or did this update screw things up?

Since the last AppleTV update I can no longer use home sharing. I have checked all IDs, re-booted iTunes, my router, and AppleTV, and checked the port settings in my firewall. nothing works. Is it me or did this last update really scew things up?

Hi,
I tried everythink, but same as before!
- droppings ot the main screen
- loosing Home Share
now even on iPads !
Frustrating!
I'm now more than convinced that this is caused by the latest iTunes version.
As some others stated in other threads .... it seems that Apple doesn't really take care of this problem. So what if, if we could make them feeling the same pain as we do. ... Just by dropping them a mail as soon as we have the problem again. Not more often, we don't want to be unfair, but everytime it happens.
I found this feedback site http://www.apple.com/feedback/itunesapp.html
I will start now with this.... maybe this will help to rise a little bit of attention
Tweety
This is the mailbody I always use
Hello all,
Since the last update to iTunes Version 10.6.1 (7) streaming content (Movies and TV shows) to Apple TVs and iPads has two major problems:
- Home Sharing is lost during streaming (streaming stops even if a large portion of the content is already preloaded)
- streaming stops and the main screen pops up (Home Sharing still available)
This happens sometime after some minutes, sometimes after several hours, but it surely happens.
I followed every advice I could found on this support website. There are now a lot of threads following this issue.
Sometimes it seems getting better, but hours later the same isues occured again. Watching content on this enviroment is a real pain and very frustrating.
As many others I'm now convinced that the latest update of iTunes caused this problem.
Our family enviroment contains the following Apple products:
- iTunes on a Win7 32 bit Noname PC (all content)
- second iTunes on a iMac with OS 10.6.8 (all content)
- third iTunes on a MacBook Pro with OS 10.6.8 (daughter, only selected content)
- fourth iTunes on a Win7 32 Samsung Notebook (son, only selected content)
- all iTunes sharing the same Home Sharing ID
- 2 Apple TV second generation
- 1 Apple TV first generation
- 2 iPod touch (bought last year)
- 2 iPads (second generation)
all firmware or software are on latest available patchlevel.
At this moment, I can not recomend to others to buy this products.
I will drop this feedback everytime my famiily and I facing this problem... just to help you to get a better feeling of the urgency of this issue.
Thanks for every effort in advanced.

Since last Airport Update, Airport Express no longer connects to network

Similar Messages

Maybe you are looking for