Single crypto with two peer

dear All,
issue : cisco 2811 , IP sec tunnel establishement with single crypto defined but two set peer
ip address.
i want to know :
In a single crypto map if i define two peer IP address (set Peer ) then did the VPN will come
up from both the Peer IP OR it will try from the first one and then switch back on the second
set peer. if later is the case then what are the reasons for causing switch back. .
Rgds,mac.

If the first one is no longer reachable, it will fall-back to the second peer.
Regards
Farrukh

Similar Messages

  • SQL Injection, replace single quote with two single quotes?

    Is replacing a single quote with two single quotes adequate
    for eliminating
    SQL injection attacks? This article (
    http://www.devguru.com/features/kb/kb100206.asp
    ) offers that advice, and it
    enabled me to allow users to search name fields in the
    database that contain
    single quotes.
    I was advised to use "Paramaterized SQL" in an earlier post,
    but I can't
    understand the concept behind that method, and whether it
    applies to
    queries, writes, or both.

    Then you can use both stored procedures and prepared
    statements.
    Both provide better protection than simply replacing
    apostrophes.
    Prepared statements are simple:
    Set myCommand = Server.CreateObject("ADODB.Command")
    ...snip...
    myCommand.CommandText = "INSERT INTO Users([Name], [Email])
    VALUES (?, ?)"
    ...snip...
    myCommand.Parameters.Append
    myCommand.CreateParameter("@Name",200,1,50,Name)
    myCommand.Parameters.Append
    myCommand.CreateParameter("@Email",200,1,50,Email)
    myCommand.Execute ,,128 'the ,,128 sets execution flags that
    tell ADO not to
    look for rows to be returned. This saves the expense of
    creating a
    recordset object you don't need.
    Stored procedures are executed in a similar manner. DW can
    help you with a
    stored procedure through the "Command (Stored Procedure)"
    server behavior.
    You can see a full example of a prepared statement by looking
    at DW's
    recordset code after you've created a recordset using version
    8.02.
    "Mike Z" <[email protected]> wrote in message
    news:eo5idq$3qr$[email protected]..
    >I should have repeated this, I am using VBScript in ASP,
    with an Access DB.
    >

  • Is it possible to use a single iPhone with two contact numbers via dual sim or an app?

    Is it possible to use a single iPhone with two contact numbers via dual sim or an app?
    This would be a useful feature for personal and company numbers but using one mobile, rather than carrying two devices or diverting calls.

    Then go ahead and try it.  You'll find it's probably a load of crap.
    You want 2 numbers, then use Google Voice or TalkaTone
    Those are US based only Apps or numbers so no good. I won't be wasting money by just trying something either, especially because using a dual sim would mean purchasing another sim card on either pay as you go or monthly contact.

  • Excel 2010; Two file opened in a single instance with two different windows... Is it possible?

    Hello
    I'm using Excel 2010
    I need to open a new Excel file to be display on a 2' monitor.  The new file need to be under the same instance has my main Excel file to prevent problem with a special dll collection that I'm using.
    I need to have both file in a separate window
    Is it possible?
    Excuse my English
    Martin

    Hi Martin,
    Open two excel file in one excel instance, display them to different windows.
    Please try the methods listed in the thread below:
    http://social.technet.microsoft.com/Forums/en-US/6ba32569-19a0-4b45-806f-9a42258bdb5f/how-to-open-two-excel-files-in-multiple-monitors-in-windows-7?forum=excel
    Best Regards,
    Wind

  • Inspection Type 10-Single Mat with two Diff Insp Typ with separate Char.

    Hi,
    I am using Inps with Mat Specs.
    I have single Finished Product having Insp type 4 & 10 attached.
    There are 8 char attached to Material out of first 4 should be visible for lot generated for insp type 4 and last 4 should be visible in Result recording screen for newly generated lot after doing Delivery i.e. 10 Insp type.
    Is there any setting for the same.
    Regards
    Nilesh

    There is no such provision available.You are using material specs then you have to consider 04 & 10 seperatly as there usage is different.
    or simply create task list with differnt usage like 1 & 6 with specific char.this will work fine.

  • Issues with sharing a single OID with two Application servers (9.0.4)

    We have two installations of 9.0.4 Application Servers and both share the same OID. We use Oracle Portal for deploying our jsp applications.
    All users in the OID are sync'ed from Microsoft Active Directory.
    Application Server 1 is for an application X
    Application Server 2 is for an application Y
    We create groups in the portal of Application Server 1 specifically for Application X. DEF_GROUP1 is default group for all applications in application X
    DEF_GROUP1 has a default page - Page 1. DEF_GROUP 1 does not exist in Application server 2
    We create groups in the portal of Application Server 2 specifically for Application Y. DEF_GROUP2 is default group for all applications in application Y
    DEF_GROUP2 has a default page - Page 2
    DEF_GROUP2 does not exist in application server 1
    We have users who access both application X and applicaiton Y
    For a user "JOHN" we assign DEF_GROUP1 in the user profile on the portal in Application Server 1
    When we go to the user profile of "JOHN" on application server 2, we find that DEF_GROUP1 is a default group in the user profile of user "JOHN"
    If we change it DEF_GROUP2, then the default group on the portal of application server 1 automatically changes to DEF_GROUP2.
    Why is this so ? We would like to have a different default group for the same user in the two portal repositories. ?
    Can any one provide some insight into this issue ?

    Basically I started to develop this system inside Oracle AS and then when it came time to passing a request to a new page, it crapped out on me on the App. Server. So instead of trying to fix the problem there and then I continued to develop outside Portal and inside Jdeveloper. After a week or two once all my stuff worked perfectly I try and take it back into Portal but only the first JSP of all my Portlets would show up, because as soon as I would submit a form and the action directed me to a new page and Portal would be lost/confused. Obviously I shouldn't have done it that way but none the less...
    So now I'm reading through the documentation you pointed me towards and it seems I have to qualify my parameters and then "attach" them to the url which the form will pass to the actioned page. I'm importing numerous classes (...urlUtils, etc) in order to qualify the parameters and then build this url without affecting any parameters currently present that my portlet does not own.
    What I'm rambling towards here is all this separation of logic and presentation and the whole nine, implies different people can develop different parts of a 'system' mostly independant of one another...so in my situation I shouldn't in huge trouble yet, since underlying everything is a working system. My issue is with oracle and the App Server. If I take my code which works great outside of the App. Server and I fully qualify parameters and make sure my form actions are constructed using the UrlUtils in order to fully qualify them as well, and then I make sure page parameters are mapped to the proper portlet parameter values....should my system work on the App Server (assuming everything is done properly)....or am I still missing something.

  • How do I replace one ' (Single Quote) with '' (Two single Quote)

    Hi,
    I have been surfing around the forum, coudn't find the similiar case.
    I have been trying but fail. Below is my code:
    activity = request.getParameter("activity");
    activity = activity.replace("\'", "\'\'");
    Error Occur:
    Incompatible type for method. Can't convert java.lang.String to char. activity = activity.replace("\'", "\'");
    I'm trying to use replaceAll(), but seem like the method is not existed, we are using Version Java 1.3
    Pls advise.
    Regards
    Ying

    For JDK 1.3 or ealier, use this:
      public static String replaceSubstrings(String str, String sub, String rep){
        int s, p, q;
        int slen = sub.length();
        StringBuffer sb = new StringBuffer();
        s = 0;
        p = str.indexOf(sub);
        q = p + slen;
        while (p != -1){
          sb.append(str.substring(s, p));
          sb.append(rep);
          s = q;
          p = str.indexOf(sub, s);
          if (p != -1){
            q = p + slen;
        sb.append(str.substring(s));
        return sb.toString();
    activity = replaceSubstrings(activity, "'", "''");

  • Best way to share AddressBook on single mac with two users?

    Hey everyone. I'm still pretty new to the Mac world here and I have a quick question. I just got my first iMac this past weekend. I've set it up so that my wife and I both have user accounts on the machine. I was wondering if there is a way or what is the best way to get it so that we can both share the same AddressBook? Is there a sync utility out there for AddressBook like there is for iCal? I would like it so that both us can can read and write to the AddressBook. Thanks in advance!

    Did you have a look at Address Book Server or Address Book X LDAP. Address Book Server let's you replicate your entire Address Book over several networks macs. Each contributing client is able to access all shared contacts, as well as make changes. Address Book Server support synchronisation in both directions.
    Address Book X LDAP on the other hand allows the updating of a centrally shared LDAP directory. It only supports writing to the LDAP directory, but has support for several attribute mappings (inetOrgPerson, abxldapPerson etc). Reading from LDAP is limited to the LDAP integration of the standard Address Book.
    Could you explain what you mean by "categories". Did you mean groups. Sharing of individual groups is supported by both tools.
    Regards
    Alex

  • Replace single quote with two single quotes

    Hi all,
    I have a value = ABCD'S(>@!23. i want to replace the value as ABCD''S(>@!23.
    Thanks in advance

    What is your database version ? Q operator works from 10G onwards.
    SQL*Plus: Release 10.2.0.1.0 - Production on Tue Nov 23 14:35:38 2010
    Copyright (c) 1982, 2005, Oracle.  All rights reserved.
    SQL> conn hr
    Enter password:
    Connected.
    SQL>  CREATE TABLE test_Q_operator(str VARCHAR2(30));
    Table created.
    SQL> INSERT INTO test_Q_operator VALUES('ABCD''S(>@!23');
    1 row created.
    SQL> INSERT INTO test_Q_operator VALUES('Saubhik''s test row');
    1 row created.
    SQL> commit;
    Commit complete.
    SQL> SELECT str,REPLACE(str,Q'[']',Q'['']') col2
      2  FROM test_Q_operator;
    STR
    COL2
    ABCD'S(>@!23
    ABCD''S(>@!23
    Saubhik's test row
    Saubhik''s test row
    SQL>Also check you SQL*PLUS client version.

  • Creating a Master with Two Detail report style

    In a Group-Above report data model, how does one add a 2nd detail group appearing at the same hierarchial level as the 1st group?
    The report already exists with MASTER and detailA. I need to add detailB and tie it to MASTER just like detailA.
    |MASTER|
    |detailA||detailB|
    \-------/\-------/

    Amjad,
    Thanks for the reply. My question relates to your suggestion #1: How does one create detailB in the data model?
    The only thing I have been able to do is to create a 2nd query linked to the 1st query. This makes the data model look like it has two masters each with one detail. What I want is a single MASTER with two details.
    Are you suggesting that the only way to accomplish this is by having two queries, one linked to the other, as in the crude rendering shown below?
    |MASTER1||MASTER2|
    |DETAIL1||DETAIL2|
    The above would be displayed in the data model as follows:
    |__Q_1___||__Q_2___|
    |G_DETAIL1||G_DETAIL2|
    \----------------/\----------------/

  • Master table with two child tables in ADF Framework

    Hi,
    I'm trying to implement single master with two detail tables using oracle adf framework of Jdev 11.1.1.4.0. I'm able to do single master-detail by using view link but unable to achieve nested details block i.e., master with nested child blocks.
    I created Query based view object of Master and two query based view objects as details. Then I created two view link for master with first child and another view link for master with second child. Even then in my data controls I see as two different components which is incorrect.
    Please let me know how to create a data control for an example shown below:
    Fruits [MASTER]
    --- Details of Fruits as adf table
    -- Apples [FIRST CHILD]
    ---- Details of Apples as adf table
    -- Oranges [SECOND CHILD]
    ---- Details of Oranges as adf table
    Regards,
    Amar.

    You need two viewLinks
    Fruits->Apples
    Fruits->Oranges
    Then in the data model you pick the Fruits entry that has:
    Fruits
    |--->Apples
    You stand on Fruits and you shuttle the Oranges to be under it from the left.
    If you'll use the default HR schema you'll see this type of relation for Employees:
    https://blogs.oracle.com/shay/entry/master_with_two_details_on_the

  • Dual uplinks with single 5400 and single 6509 (with multiple interface cards)

    I have a single 5400 with two gige ports and a single 6509 with dual gige line cards.
    What would be the best method for running them with dual connections in case an interface or line card goes bad?
    Thanks in advance.

    Thank you for the reply Joseph. I swear I've ran SLA on 6500's before. This box is running IOS 12.2 so maybe that's the culprit.
    I found a simple way to configure both devices redundantly using administrative distanced routes pointing through a specified interface. On the 6509, the routes point to a loopback address on the 5400, on the 5400 it's configured as default routes. Like this document explains:
    http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/27082-ip-static-routes.html
    Seems to work like a champ.

  • TWO DATASETS  WITH TWO REPORTS IN SINGLE RTF

    Hi All,
    i want to use two datasets in BIP followed by single RTF having two different reports(DS1-Table1,DS2-Table2) we are using SQL queries for the dataset please give some suggestions how to connect two diiferent datasets with two different tables in a single RTF
    note:
    output of dataset 1 should come in table 1
    output of dataset 2 should come in table 2 and both this tables are in single rtf
    we have used Concatenate operator in BIP but its doing Union and thrwing the output in single table not in two different tables please help
    regards
    bhaskar

    Table 1
         0-1 year     Over 1year     Total
    LC               0.00
    Guarantees               0.00
    Others (specify)               0.00
    Total     0.00     0.00     0.00
    =======================================================================================
    Table 2
         0-1 year     Over 1year     Total
    Unutilized Lines of Credit               0.00
    Unutilized Overdraft Facilities               0.00
    Others (specify)               0.00
    Total     0.00     0.00     0.00
    We are using two different SQl queries for the table 1 and table 2 this two tables should appear in Single RTF
    i.e sql 1 should come only in table 1
    and sql2 should come only in table 2
    i have used Concatenate operation in BIP with multiple datasets its repeating in single table1 and i am unable to split them into two tables please help on this

  • Is there a download and convert in a single step option in the flashdownloader 2.6.8. add-on? I end up with two files, one downloaded original and one converted to my chosen format.

    Files are downloaded and only then encoded, so I end up with two files in the drive.

    That has been like that since Firefox 3.0 was released in June 2008 - 7 major version releases thus far with it like that and the developers haven't changed it - so I wouldn't count on it.
    When I want to save a duplicate bookmark, I just "grab" the website image in the Location Bar and drag it into the Bookmarks Sidebar, into the folder where I want it placed. On Windows and Linux, { Ctrl + B } opens the sidebar and then just drag.

  • One job with two steps - how to create one single spool?

    Hello experts,
    I have created two queries in SQVI. One is based on the table BSIK, the other on on BSAK.
    The report layout is the same in both queries.
    Now I schedule one job in SM36/SM37 with two steps corresponding to my queries.
    I want my second step to append the spool created in the first step. Is that possible?
    In order to do this I unchecked "New spool request" in the request attributes for the second step of the job.
    I use the same printer, the same format (X_65_80), but it doesnt work.
    The help on the field says
    ".... name, output device, number of prints and the format must match..." - What "name" do they mean?
    "In addition, the existent spool order must not already be competed. This can occur if a spool is released for output...." - I use "send to SAP spooler only" option, is that what thay mean? How cen you have an "uncompleted spool" in the job.
    If anybody knows ho to do this (without development!), please advise
    Best regards,
    Fatima

    Hi,
    Please do following steps :
    1. Go to transaction code SM36
    2. Do as per below screen shots
    You can see Job steps is empty
    Click on (Check and Save)
    Next Screen
    You can see one step created
    Click on Create
    You can see above it is showing as Step 2
    Give again program name and variant
    Click on (Check and Save)
    You can see two steps are created
    Go back (green arrow)
    You can see know SAP is showing 2 Step(s) successfully defined which was earlier blank
    Click on
    Next Screen
    Now schedule job as per your requirement.
    Prerequisite create variants for both the programs as we need to mention the same .
    Hope, this solves your issue else revert.
    Regards,
    Tejas

Maybe you are looking for