SIP Inspection Required
Hi everyone,
Do I need to enable SIP inspection as per this article?
We're trying a proof-of-concept install for the Cisco Mobile iPhone client and the Cisco Cius, since we do not have any corporate WiFi we're utilising the AnyConnect clients that are available on both via our ASA5510 appliances that are running 8.3(1). However, we are unable to make calls via the VPN and find that the call initially rings but the call isn't fully setup when answered (The calling side will just continue to ring).
I'm seeing TCP connections (See attached syslog messages) being denied for port 5060 on the basis that there is no existing connection as the previous TCP connection is torn down. Hoping I can get some confirmation here before giving it a go.
Thanks,
Mark
Mark,
Normally you do not need to have inspection over VPN:
1) Typically you do not have NAT over VPN (typically!)
2) All the traffic is allowed over VPN by default (there is a sysopt for VPN traffic to ignore ACLs)
Now if it really is a problem of inspection, it's hard to say.
Did you try skinny instead of SIP? (Just out of curiosity).
Marcin
Similar Messages
-
Hi
I have set up clustering on 2 ASA 5555-x firewalls and just saw on the cisco site that SIP inspection is not supported. My organization provides a voip solution that requires SIP. Does anyone know a work around for SIP on an ASA cluster?
I look forward to your response.Hi Smetieh,
You need a policy inspection for sip, please follow the example below.
class-map cls-SIP
match default-inspection-traffic
policy-map pmap-SIP
description My-SIP Policy
class cls-SIP
inspect sip
service-policy pmap-SIP interface outside
Hope this helps.
Thanks
Rizwan Rafeek. -
SIP Inspection and dynamic port opening after re-invite
Platform: ASA 8.3(2)
Hello,
I have SIP devices along with SipTrunk and media endpoints. I am having issues with the ASA not dynamically opening (sip inspect enabled) UDP ports for RTP after a SIP re-invite causes the media endpoints to change within SDP.
The problem as below.
Initial SIP invite setups properly with ports dynamically opened between the media endpoints in the ASA
Re-inivite from the SIP device causes the media endpoints to change within the SDP
ASA blocks ports associated to the new media endpoints
I can resolve this by allowing the ports in the ACL, but suprised this is not working as re-invites to change media endpoints is to be expected in SIP conversation.
Regards,
AJBelow is the script you can use to reproduce this. Points worth mentioning.
Initial invite sets up the media between SIP Trunk and a media device ( 10.1.2.150) in the inside network, SIP signalling will be with 10.1.2.100. At this poit RTP flows freely between the SIP Trunk and the media device.
If the call is fax, a re-invite will occur and this will cause the IP address to change in the SDP. The new media endpoint becomes 10.1.2.151 (This device is SIP and Media (T38) capable).
For every SIP call we establish 10.1.2.150 will be used for media, we do not want to change this behaviour.
ASA 8.3 (2)
conf t
interface Ethernet0/0
nameif Inside_Voice
security-level 100
ip address 10.1.2.11 255.255.255.0 standby 10.1.2.12
exit
interface Ethernet0/1
nameif Outside_SIP_Trunk
security-level 0
ip address 10.1.60.254 255.255.255.0 standby 10.1.60.253
exit
object-group network SIP_trunks
network-object 1.2.3.0 255.255.255.0
exit
object-group service SIP_service
service-object tcp destination eq sip
service-object udp destination eq sip
exit
object-group network SIP_inside_servers
network-object host 10.1.2.100
exit
access-list Outside_SIP_in extended permit object-group SIP_service object-group SIP_trunks object-group SIP_inside_servers
access-group Outside_SIP_in in interface Outside_SIP_Trunk
route Outside_SIP_Trunk 0.0.0.0 0.0.0.0 10.1.60.1
class-map inspection_default
match default-inspection-traffic
exit
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
inspect icmp error
lass class-default
set connection decrement-ttl
exit
service-policy global_policy global
end -
We recently had a vendor switch from Cisco SIP to PJSIP. After the migration it was necessary for us to add an access list to allow UDP port range 60000 65535. To the best of my knowledge this part of the reason we enabled SIP inspect several years ago on the Cisco ASA. I saw evidence of these ports being denies in the syslog before I added these ports to the access-list. I am sorry to report that our log history does not go back far enough to see the pack flow before the change.
Any suggestion you might have to assist me in my research would be appreciated.
ASA 5520 ASA Version 8.2(5)33
inspect rtsp
inspect sipHi,
One of the reasons for the SIP inspection is for the ASA device to dynamically open Pin Holes (Secondary Channels) for the Audio Communication trough the ASA device without having to open the huge range of ports.
I don't think PJSIP would be supported as an inspection protocol and hence you would have to open these HIgh Range ports through the ASA device.
Hope that answers your query.
Thanks and Regards,
Vibhor Amrodia -
QM Inspection requirement?
Hi All,
We have a requirement as given below...
A vendor and/or a material must be selected (manually) and then this vendor or material
must be flagged at the goods receipt for quality inspection.
My client does not want to implement the quality inspection functionality in SAP QM. Can we achieve the above requirement in any way without QM inspection ?
Even a workaround would do.
Please guide...
Regards,
V SOne More Solution: -
First Create Good receipt with movement type 103 - Good receipt in Blocked stock.
After checking material quality then release material with movement type 105 - Good receipt from blocked stock to release stock.
Regards,
Mahesh Wagh -
Communicator connection issues, sample OCMS-SIP application required
Hi,
I have installed OCMS 10.1.3.3 in my machine as Standalone Developer mode. I am able to connect using Oracle Communicator from the local machine. But if I try Oracle communicator from other machines, it's failing to connect. Communicator (Local Install) connects and disconnects automatically (frequently - within 10seconds). Pl see the log messages attached at the end.
Also can anybody please provide me source code of any sample OCMS - SIP application.
Thanks in Advance.
2007-10-19 14:51:19,674+0530 346408 WARN [SubscribeServlet] (HTTPThreadGroup-9:) Terminating Subscriber Id: [email protected] Resource Id: [email protected] Dialog: call-id: c80126ad-e0f5-4004-9903-18118e8ab47e local-tag: null remote-tag: 7b397ca0-739a-4cbd-a142-2483cf5d81e3 because the response was failure 481
2007-10-19 14:51:59,752+0530 386486 WARN [SubscribeServlet] (HTTPThreadGroup-12:) Terminating Subscriber Id: [email protected] Resource Id: [email protected] Dialog: call-id: 9914c1ee-979a-4650-9246-28d962adae8c local-tag: null remote-tag: 412d616e-a4fe-4e72-856a-402d324ef32a because the response was failure 481
2007-10-19 14:52:19,731+0530 406465 WARN [SubscribeServlet] (HTTPThreadGroup-6:) Terminating Subscriber Id: [email protected] Resource Id: [email protected] Dialog: call-id: 160693c2-1cff-4d40-8a30-9af55a9da7bc local-tag: null remote-tag: e84b62a1-8dc3-43c5-84a7-0d87fd2bf619 because the response was failure 481Hi
Start the OCMS installer and install SCE for Eclipse.
Then you will get access to some sample code.
Cheers
Lucas -
Cisco 2811 - Multiple SIP with CME 8.6
PLAN:
Configure two SIP providers with my Cisco ISR 2811 using CME 8.6
sip.fongo.com
sip.voicediscount.com
All incoming and local outgoing calls using fongo, while long distance & international via voipdiscount.
I have successfully got fongo.com service to work for both incoming and outgoing, however when I try a long distance & international calls I get a busy tone.
Any help will be appreciated since I've had no luck
CONFIG:
BNET01C2811-TOR1807#sh run
Building configuration...
Current configuration : 19512 bytes
! Last configuration change at 21:48:40 EDT Sat Oct 27 2012 by garrett
! NVRAM config last updated at 21:50:55 EDT Sat Oct 27 2012 by garrett
! NVRAM config last updated at 21:50:55 EDT Sat Oct 27 2012 by garrett
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname BNET01C2811-TOR1807
boot-start-marker
boot system flash:c2800nm-adventerprisek9-mz.151-4.m5.bin
boot-end-marker
! card type command needed for slot/vwic-slot 0/0
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200
logging console critical
enable secret 5 $1$r/t3$A3xgJf.ngqbUq.sDiNC4O0
no aaa new-model
clock timezone EST -4 0
clock summer-time EDT recurring
clock calendar-valid
dot11 syslog
no ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.15.0.0 10.15.0.20
ip dhcp pool TOR-1807WEBB
network 10.15.0.0 255.255.255.0
default-router 10.15.0.15
dns-server 64.71.255.198
option 150 ip 10.15.0.15
no ip bootp server
ip domain name bayross.net
ip name-server 64.71.255.198
ip ddns update method sdm_ddns1
HTTP
add http://bayross:******@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://bayross:********@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 1 1 0 0
interval minimum 1 1 0 0
no ipv6 cef
multilink bundle-name authenticated
parameter-map type protocol-info yahoo-servers
server name scs.msg.yahoo.com
server name scsa.msg.yahoo.com
server name scsb.msg.yahoo.com
server name scsc.msg.yahoo.com
server name scsd.msg.yahoo.com
server name cs16.msg.dcn.yahoo.com
server name cs19.msg.dcn.yahoo.com
server name cs42.msg.dcn.yahoo.com
server name cs53.msg.dcn.yahoo.com
server name cs54.msg.dcn.yahoo.com
server name ads1.vip.scd.yahoo.com
server name radio1.launch.vip.dal.yahoo.com
server name in1.msg.vip.re2.yahoo.com
server name data1.my.vip.sc5.yahoo.com
server name address1.pim.vip.mud.yahoo.com
server name edit.messenger.yahoo.com
server name messenger.yahoo.com
server name http.pager.yahoo.com
server name privacy.yahoo.com
server name csa.yahoo.com
server name csb.yahoo.com
server name csc.yahoo.com
parameter-map type protocol-info aol-servers
server name login.oscar.aol.com
server name toc.oscar.aol.com
server name oam-d09a.blue.aol.com
parameter-map type protocol-info msn-servers
server name messenger.hotmail.com
server name gateway.messenger.hotmail.com
server name webmessenger.msn.com
voice service voip
ip address trusted list
ipv4 46.19.209.10
ipv4 46.19.209.11
ipv4 46.19.209.12
ipv4 46.19.209.13
ipv4 46.19.209.14
ipv4 46.19.209.15
ipv4 46.19.209.75
ipv4 46.19.209.76
ipv4 46.19.209.77
ipv4 46.19.209.78
ipv4 46.19.209.79
ipv4 46.19.209.80
ipv4 46.19.210.10
ipv4 46.19.210.11
ipv4 46.19.210.12
ipv4 46.19.210.13
ipv4 46.19.210.14
ipv4 46.19.210.15
ipv4 46.19.210.75
ipv4 46.19.210.76
ipv4 46.19.210.77
ipv4 46.19.210.78
ipv4 46.19.210.79
ipv4 46.19.210.80
ipv4 81.85.224.40
ipv4 81.85.224.41
ipv4 212.150.88.21
ipv4 212.150.88.23
ipv4 212.150.88.24
ipv4 208.65.240.165
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
redirect ip2ip
fax protocol pass-through g711ulaw
h323
no h225 timeout keepalive
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
voice register global
mode cme
source-address 10.15.0.15 port 5060
max-dn 100
max-pool 25
tftp-path flash:
create profile sync 0002145265491175
camera
voice translation-rule 2
rule 1 /9905+/ /905/
rule 2 /9416+/ /416/
rule 3 /9647+/ /647/
voice translation-rule 4
rule 1 /91+/ /1/
voice translation-rule 5
rule 1 /9011+/ /011/
voice translation-rule 7
rule 1 /1011/ /16472473297/
voice translation-rule 911
rule 1 /111/ /6473385738/
voice translation-rule 2473297
rule 1 /16472473297/ /1011/
voice translation-profile Caller-ID
translate calling 7
voice translation-profile Emergency
translate called 911
voice translation-profile Incoming
translate called 2473297
voice translation-profile International
translate calling 7
translate called 5
voice translation-profile Local
translate calling 7
translate called 2
voice translation-profile LongDistance
translate calling 7
translate called 4
voice-card 0
dsp services dspfarm
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-21053818
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-21053818
revocation-check none
rsakeypair TP-self-signed-21053818
crypto pki trustpoint test_trustpoint_config_created_for_sdm
subject-name [email protected]
revocation-check crl
crypto pki certificate chain TP-self-signed-21053818
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32313035 33383138 301E170D 31323130 31373131 33303333
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D323130 35333831
3830819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100B080
AD5A9751 C15D5932 0677DBEF A59AF6B0 1EF55BE0 B1DFA4B8 397130B7 90BA221D
5A03F805 DD546B79 D40CD413 3FD7CCFC A2137323 63E26137 8577DD77 C1787B0E
ADC65091 042897A3 2F26DAC0 CCF0E0AC 604AA2B4 48616FE3 976E17B6 53ABC719
16EFA128 8F883BFA 39FA02EF CA820300 4B650412 77418E6D AE45C6A1 0FEB0203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14504E01 C3E57E38 CAB8659D 21D57880 66FE3CDB 83301D06 03551D0E
04160414 504E01C3 E57E38CA B8659D21 D5788066 FE3CDB83 300D0609 2A864886
F70D0101 05050003 81810049 A534494C B6777D5B FCAB252E 8FD03C10 D917714E
3314139B 04FCB2CC 74C06091 D189470E 930CEA8A 393461A7 E505BB0A 59DEDF5C
37711F56 127E22C6 CA9457EC 960A868D 37B24F75 A03B1F8B A611D77F 0E79B2D8
135C57AF B9705B78 BA97BFF3 5967C1D1 6E2B92D3 A8BE055B 10A59F2C 5D28C55B
2164E3C7 7F2380E1 E33AD4
quit
crypto pki certificate chain test_trustpoint_config_created_for_sdm
license udi pid CISCO2811 sn FHK1041F27M
username garrett privilege 15 password 7 070D000000094C50
redundancy
ip tcp synwait-time 10
no ip ftp passive
class-map type inspect match-any SDM_BOOTPC
match access-group name SDM_BOOTPC
class-map type inspect match-any ccp-cls-protocol-p2p
match protocol edonkey signature
match protocol gnutella signature
match protocol kazaa2 signature
match protocol fasttrack signature
match protocol bittorrent signature
class-map type inspect match-any SDM_DHCP_CLIENT_PT
match class-map SDM_BOOTPC
class-map type inspect match-any ccp-skinny-inspect
match protocol skinny
class-map type inspect match-any sdm-cls-bootps
match protocol bootps
class-map type inspect match-any ccp-cls-insp-traffic
match protocol dns
match protocol ftp
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map match-any CCP-Transactional-1
match dscp af21
match dscp af22
match dscp af23
class-map type inspect match-any ccp-h323nxg-inspect
match protocol h323-nxg
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-any ccp-cls-protocol-im
match protocol ymsgr yahoo-servers
match protocol msnmsgr msn-servers
match protocol aol aol-servers
class-map match-any CCP-Voice-1
match dscp ef
class-map type inspect match-any ccp-h225ras-inspect
match protocol h225ras
class-map match-any CCP-Routing-1
match dscp cs6
class-map match-any CCP-Signaling-1
match dscp cs3
match dscp af31
class-map type inspect match-any ccp-h323annexe-inspect
match protocol h323-annexe
class-map match-any CCP-Management-1
match dscp cs2
class-map type inspect match-any ccp-h323-inspect
match protocol h323
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-any ccp-sip-inspect
match protocol sip
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map CCP-QoS-Policy-1
class CCP-Voice-1
priority percent 33
class CCP-Signaling-1
bandwidth percent 5
class CCP-Routing-1
bandwidth percent 5
class CCP-Management-1
bandwidth percent 5
class CCP-Transactional-1
bandwidth percent 5
class class-default
fair-queue
random-detect
policy-map type inspect ccp-permit-icmpreply
class type inspect sdm-cls-bootps
pass
class type inspect ccp-sip-inspect
pass
class type inspect ccp-h323-inspect
inspect
class type inspect ccp-h323annexe-inspect
inspect
class type inspect ccp-h225ras-inspect
inspect
class type inspect ccp-h323nxg-inspect
inspect
class type inspect ccp-skinny-inspect
inspect
class type inspect ccp-icmp-access
inspect
class class-default
pass
policy-map sdm-qos-test-123
class class-default
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
drop log
class type inspect ccp-protocol-http
inspect
class type inspect ccp-insp-traffic
inspect
class type inspect ccp-sip-inspect
pass
class type inspect ccp-h323-inspect
inspect
class type inspect ccp-h323annexe-inspect
inspect
class type inspect ccp-h225ras-inspect
inspect
class type inspect ccp-h323nxg-inspect
inspect
class type inspect ccp-skinny-inspect
inspect
class class-default
drop
policy-map type inspect ccp-permit
class type inspect SDM_DHCP_CLIENT_PT
pass
class type inspect ccp-sip-inspect
pass
class type inspect ccp-h323-inspect
inspect
class type inspect ccp-h323annexe-inspect
inspect
class type inspect ccp-h225ras-inspect
inspect
class type inspect ccp-h323nxg-inspect
inspect
class type inspect ccp-skinny-inspect
inspect
class class-default
drop
zone security in-zone
zone security out-zone
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
interface Null0
no ip unreachables
interface FastEthernet0/0
description $ES_LAN$$FW_INSIDE$
ip address 10.15.0.15 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
duplex full
speed auto
no mop enabled
interface FastEthernet0/1
description $FW_OUTSIDE$$ETH-WAN$
ip dhcp client update dns server none
ip ddns update sdm_ddns1
ip address dhcp client-id FastEthernet0/1 hostname bayross.net
no ip redirects
no ip unreachables
no ip proxy-arp
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
duplex auto
speed auto
no mop enabled
service-policy output CCP-QoS-Policy-1
interface FastEthernet0/2/0
no ip address
shutdown
interface FastEthernet0/2/1
no ip address
shutdown
interface FastEthernet0/2/2
no ip address
shutdown
interface FastEthernet0/2/3
no ip address
shutdown
interface Vlan1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
ip forward-protocol nd
ip http server
ip http access-class 2
ip http authentication local
ip http secure-server
ip http path flash:
ip flow-top-talkers
top 10
sort-by bytes
cache-timeout 60000
ip nat inside source list 1 interface FastEthernet0/1 overload
ip access-list extended SDM_BOOTPC
remark CCP_ACL Category=0
permit udp any any eq bootpc
logging trap debugging
access-list 1 remark INSIDE_IF=FastEthernet0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.15.0.0 0.0.0.255
access-list 2 remark HTTP Access-class list
access-list 2 remark CCP_ACL Category=1
access-list 2 permit 10.15.0.0 0.0.0.255
access-list 2 deny any
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
no cdp run
tftp-server flash:term41.default.loads alias term41.default.loads
tftp-server flash:term61.default.loads alias term61.default.loads
tftp-server flash:Analog1.raw
tftp-server flash:Analog2.raw
tftp-server flash:AreYouThere.raw
tftp-server flash:AreYouThereF.raw
tftp-server flash:Bass.raw
tftp-server flash:CallBack.raw
tftp-server flash:Chime.raw
tftp-server flash:Classic1.raw
tftp-server flash:Classic2.raw
tftp-server flash:ClockShop.raw
tftp-server flash:DistinctiveRingList.xml
tftp-server flash:Drums1.raw
tftp-server flash:Drums2.raw
tftp-server flash:FilmScore.raw
tftp-server flash:HarpSynth.raw
tftp-server flash:Jamaica.raw
tftp-server flash:KotoEffect.raw
tftp-server flash:MusicBox.raw
tftp-server flash:Piano1.raw
tftp-server flash:Piano2.raw
tftp-server flash:Pop.raw
tftp-server flash:Pulse1.raw
tftp-server flash:Ring1.raw
tftp-server flash:Ring2.raw
tftp-server flash:Ring3.raw
tftp-server flash:Ring4.raw
tftp-server flash:Ring5.raw
tftp-server flash:Ring6.raw
tftp-server flash:Ring7.raw
tftp-server flash:RingList.xml
tftp-server flash:Sax1.raw
tftp-server flash:Sax2.raw
tftp-server flash:Vibe.raw
tftp-server flash:P00308010200.bin alias P00308010200.bin
control-plane
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/1/2
voice-port 0/1/3
voice-port 0/3/0
caller-id enable
voice-port 0/3/1
caller-id enable
mgcp profile default
sccp local FastEthernet0/0
sccp ccm 10.15.0.15 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register confprof2
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 20
shutdown
dspfarm profile 2 conference
codec g711ulaw
codec g711alaw
maximum sessions 5
associate application SCCP
dial-peer cor custom
name Main1_10Digit
name Main1_11Digit
dial-peer cor list Main1-11Digit
member Main1_11Digit
dial-peer cor list Main1-Line
member Main1_10Digit
member Main1_11Digit
dial-peer voice 1 voip
description ## INCOMING - DIDWW - 16472584731 ##
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 16472584731
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2003 pots
description #### INCOMING INTERFACE 0/3/1 ####
destination-pattern 16472584731
incoming called-number 16472584731
port 0/3/1
dial-peer voice 1000 pots
description #### KITCHEN ####
destination-pattern 1000
port 0/3/0
dial-peer voice 1003 pots
description #### MASTER BEDROOM ####
destination-pattern 1003
port 0/3/1
dial-peer voice 10 voip
corlist outgoing Main1-11Digit
description Main1 11-Digit Outgoing
translation-profile outgoing LongDistance
destination-pattern 91..........
session protocol sipv2
session target dns:sip.voipdiscount.com
session transport udp
dtmf-relay rtp-nte sip-notify
codec g711ulaw
no vad
dial-peer voice 11 voip
corlist outgoing Main1-Line
translation-profile incoming Incoming
translation-profile outgoing Local
destination-pattern 9[^1]..[2-9]......
session protocol sipv2
session target dns:sip.fongo.com
incoming called-number .
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 12 voip
translation-profile outgoing International
destination-pattern 9011T
session protocol sipv2
session target dns:sip.voipdiscount.com
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 911 voip
translation-profile outgoing Emergency
destination-pattern 111
session protocol sipv2
session target dns:sip.fongo.com
dtmf-relay rtp-nte
codec g711ulaw
no vad
gateway
timer receive-rtp 1200
sip-ua
credentials username 37373737373 password 7 00000000000000000000 realm sip.fongo.com
credentials username username password 7 00000000000000000000 realm sip.voipdiscount.com
authentication username username password 7 0000000000000000000000000 realm sip.voipdiscount.com
no remote-party-id
srv version 1
retry invite 3
retry register 10
timers register 150
registrar 1 dns:sip.voipdiscount.com expires 3600
registrar 2 dns:sip.fongo.com expires 3600
sip-server dns:sip.voipdiscount.com
host-registrar
telephony-service
sdspfarm units 1
sdspfarm transcode sessions 5
sdspfarm tag 1 confprof2
conference hardware
no auto-reg-ephone
max-ephones 25
max-dn 100
ip source-address 10.15.0.15 port 2000
system message Bayross Residence
cnf-file location flash:
user-locale US load CME-locale-en_US-English-7.0.1.1.tar
load 7960-7940 P00308010200.loads
load 7941 SCCP41.9-1-1SR1S.loads
load 7941GE SCCP41.9-1-1SR1S.loads
load 7961 SCCP41.9-1-1SR1S.loads
load 7961GE SCCP41.9-1-1SR1S.loads
time-zone 12
max-conferences 8 gain -6
moh flash:/music-on-hold.au
web admin system name garrett secret 5 $1$MjiP$KMQoyqL/3mnftN0OLqs8b1
time-webedit
transfer-system full-consult
secondary-dialtone 9
create cnf-files version-stamp 7960 Oct 26 2012 19:53:22
ephone-dn 2 octo-line
number A001
conference ad-hoc
preference 3
ephone-dn 3 octo-line
number A002
conference ad-hoc
preference 3
ephone-dn 4 octo-line
number A003
conference ad-hoc
preference 3
ephone-dn 5 octo-line
number A004
conference ad-hoc
preference 3
ephone-dn 6 octo-line
number A005
conference ad-hoc
preference 3
ephone-dn 11 dual-line
number 1011 secondary 16472473297 no-reg both
corlist incoming Main1-Line
ephone-dn 12 dual-line
number 1012
label Garrett Bayross
name Garrett Bayross
corlist incoming Main1-Line
ephone 1
no multicast-moh
device-security-mode none
mac-address F04D.A28C.CBAC
mtp
type CIPC
button 1:11
ephone 2
device-security-mode none
mac-address 0016.4697.A472
type 7940
button 1:12
banner login ^CBayross.NET Network
^C
banner motd ^C
line con 0
logging synchronous
line aux 0
line vty 0 4
login local
transport input all
transport output all
scheduler allocate 20000 1000
ntp update-calendar
ntp server 128.100.100.128 prefer source FastEthernet0/1
endDEBUG OUTPUT:
login as: garrett
Bayross.NET Network
Using keyboard-interactive authentication.
Password:
------------- LEGAL NOTICE ----------------
-- THIS IS A PRIVATE SYSTEM --
-- UNAUTHORIZED ACCESS IS PROHIBITED --
-- CECI EST UN SYSTEME PRIVE --
-- TOUT ACCES NON AUTORISE EST INTERDIT --
BNET01C2811-TOR1807#deb
BNET01C2811-TOR1807#debug ccsip all
This may severely impact system performance. Continue? [confirm]
All SIP Call tracing is enabled
BNET01C2811-TOR1807#term mon
BNET01C2811-TOR1807#REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:43 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385503
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859402: Oct 27 21:51:47.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859403: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859404: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859405: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859406: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859407: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859408: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859409: Oct 27 21:51:47.834 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.134, rport:5060 with laddr:
1859410: Oct 27 21:51:47.834 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859411: Oct 27 21:51:47.834 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, local_addr=, connId=4 for UDP
1859412: Oct 27 21:51:47.838 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:47 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385507
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859413: Oct 27 21:51:51.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859414: Oct 27 21:51:51.834 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859415: Oct 27 21:51:51.834 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859416: Oct 27 21:51:51.834 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859417: Oct 27 21:51:51.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859418: Oct 27 21:51:51.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859419: Oct 27 21:51:51.838 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859420: Oct 27 21:51:51.838 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.134, rport:5060 with laddr:
1859421: Oct 27 21:51:51.838 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859422: Oct 27 21:51:51.838 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, local_addr=, connId=4 for UDP
1859423: Oct 27 21:51:51.842 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:51 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385511
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859424: Oct 27 21:51:55.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859425: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859426: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859427: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859428: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859429: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859430: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859431: Oct 27 21:51:55.834 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.134, rport:5060 with laddr:
1859432: Oct 27 21:51:55.834 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859433: Oct 27 21:51:55.834 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.134, port=5060, local_addr=, connId=4 for UDP
1859434: Oct 27 21:51:55.838 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:55 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385515
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859435: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: calling reg_invoke_ip_first_hop()
1859436: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: calling ip_best_local_address()
1859437: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: return addr 99.230.172.76
1859438: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: calling reg_invoke_ip_first_hop()
1859439: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: calling ip_best_local_address()
1859440: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/resolve_sig_ip_address_to_bind: return addr 99.230.172.76
1859441: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/ccsip_spi_register_get_rcb: Getting New RCB [0x4C6D2730]
1859442: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/ccsipGetCCBFromRCB: Retrived CCB pointer [0x0]
1859443: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/ccsip_spi_register_free_rcb: Freeing rcb [0x4C6D1BAC]
1859444: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/ccsip_register_set_dns_resolved_address: CCSIP_REGISTER:: registrar 0 DNS resolved addr set to 77.72.169.131:5060
1859445: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/ccsipRegisterStartRCBTimer: Starting timer for pattern for 3600 seconds
1859446: Oct 27 21:51:59.834 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859447: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859448: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859449: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859450: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x41C25300
1859451: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859452: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859453: Oct 27 21:51:59.838 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859454: Oct 27 21:51:59.838 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859455: Oct 27 21:51:59.838 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859456: Oct 27 21:51:59.842 EDT: //3542/000000000000/SIP/State/sipSPIChangeState: 0x4B6533C0 : State change from (SIP_STATE_OUTGOING_REGISTER, SUBSTATE_NONE) to (SIP_STATE_OUTGOING_REGISTER, SUBSTATE_NONE)
1859457: Oct 27 21:51:59.846 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:59 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385519
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859458: Oct 27 21:51:59.990 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859459: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859460: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859461: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859462: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859463: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859464: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859465: Oct 27 21:51:59.990 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859466: Oct 27 21:51:59.990 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859467: Oct 27 21:51:59.990 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859468: Oct 27 21:51:59.994 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:51:59 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385519
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859469: Oct 27 21:52:00.290 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859470: Oct 27 21:52:00.290 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859471: Oct 27 21:52:00.290 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859472: Oct 27 21:52:00.290 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859473: Oct 27 21:52:00.290 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859474: Oct 27 21:52:00.290 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859475: Oct 27 21:52:00.294 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859476: Oct 27 21:52:00.294 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859477: Oct 27 21:52:00.294 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859478: Oct 27 21:52:00.294 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859479: Oct 27 21:52:00.294 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:52:00 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385520
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859480: Oct 27 21:52:00.891 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859481: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859482: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859483: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859484: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859485: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859486: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859487: Oct 27 21:52:00.891 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859488: Oct 27 21:52:00.891 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859489: Oct 27 21:52:00.891 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859490: Oct 27 21:52:00.899 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:52:00 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385520
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859491: Oct 27 21:52:02.091 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859492: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859493: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859494: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859495: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859496: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859497: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859498: Oct 27 21:52:02.091 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859499: Oct 27 21:52:02.091 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859500: Oct 27 21:52:02.091 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859501: Oct 27 21:52:02.099 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:sip.voipdiscount.com:5060 SIP/2.0
Via: SIP/2.0/UDP 99.230.172.76:5060;branch=z9hG4bKED020B5
From: [email protected]>;tag=59BB550-3A6
To: [email protected]>
Date: Sun, 28 Oct 2012 00:52:02 GMT
Call-ID: C977B084-1FCE11E2-81A4A3AB-85AB6D24
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1351385522
CSeq: 5 REGISTER
Contact:
Expires: 3600
Supported: path
Content-Length: 0
1859502: Oct 27 21:52:04.491 EDT: //-1/xxxxxxxxxxxx/SIP/Info/sipSPISetDateHeader: Converting TimeZone EDT to SIP default timezone = GMT
1859503: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Info/sipSPISendRegister: Associated container=0x4E3C18B0 to Register
1859504: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipSPISendRegister: Sending REGISTER to the transport layer
1859505: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipSPIGetSwitchTransportFlag: Return the Global configuration, Switch Transport is FALSE
1859506: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, sentBy_port=0, local_addr=, is_req=1, transport=1, switch=0, callBack=0x0
1859507: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipSPITransportSendMessage: Proceedable for sending msg immediately
1859508: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: switch transport is 0
1859509: Oct 27 21:52:04.491 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipConnectionManagerGetConnection: connection required for raddr:77.72.169.131, rport:5060 with laddr:
1859510: Oct 27 21:52:04.491 EDT: //3542/000000000000/SIP/Transport/sipTransportLogicSendMsg: Set to send the msg=0x4CCD8DC8
1859511: Oct 27 21:52:04.491 EDT: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostSendMessage: Posting send for msg=0x4CCD8DC8, addr=77.72.169.131, port=5060, local_addr=, connId=2 for UDP
1859512: Oct 27 21:52:04.495 EDT: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent: -
ASA 5540 8.4 and Voice Gateway (SIP)
have ASA FW with 8.4(2) : inside is connected to lan , DMZ is having SIP Gateway router , i have configured the Firewall will required ports and enabled sip inspection under policy-map but no VOICE traffic is passing through the firewall , iam using static nat
there are ports opened from both side ASA (dmz-inside and other way)
object-group service TCP tcp
port-object eq sip
port-object range 2000 2443
port-object eq h323
port-object eq rtsp
port-object eq 5061
port-object eq 50693
port-object eq 16341
object-group service UDP udp
port-object eq sip
port-object range 16384 32767
port-object eq tftp
port-object eq ntp
port-object eq 1718
port-object eq 1719
port-object eq 5061
port-object eq 57280
Following is inspection
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect dns
service-policy global_policy global
phones are not getting registered .....how about the NAT it should be static between DMZ to inside or No NAT statement
any sugesstions would be helpfullAlthough it is a document about ASA on another version it explains how SIP inspection works on the ASA. For you to understand this document you need to understand the device that you are configuring behind the ASA and how SIP works in general.
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008081042c.shtml
Send a copy of the complete configuration and show service-policy -
Help required when using Function module F4_INT_TABLE_VALUE_REQUEST
Hi,
I wrote the logic as follows.
Select-options: s_lgart FOR pa0015-lgart.
SELECT lgart FROM t512z INTO TABLE it_temp WHERE infty = '0015' AND lgart IN rlgart.
IF NOT it_temp[] IS INITIAL.
SORT it_temp BY lgart.
DELETE ADJACENT DUPLICATES FROM it_temp COMPARING lgart.
LOOP AT it_temp.
SELECT SINGLE lgtxt FROM t512t INTO it_temp-description
WHERE lgart = it_temp-lgart AND
sprsl = 'EN'.
IF sy-subrc = 0.
MODIFY it_temp INDEX sy-tabix.
ENDIF.
ENDLOOP.
at present in internal table it_temp having following fields.
5100 Relolump sum
5111 SIP
my requirement is : when i press F4 help on wage type in selection screen i am able to see two fieexample:
CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
EXPORTING
RETFIELD = 'VBELN'
DYNPPROG = W_PROGNAME
DYNPNR = W_SCR_NUM
DYNPROFIELD = 'KUNNR'
VALUE_ORG = 'S'
TABLES
VALUE_TAB = INT_F4
RETURN_TAB = RETURN_VALUES
EXCEPTIONS
PARAMETER_ERROR = 1
NO_VALUES_FOUND = 2
OTHERS = 3. -
Sale Order / Project specific Inspection Plan
Dear All,
I want to create Sale order or Project specific inspection plan for a material. This is because, my customers want some specific inspection requirements for individual materials, which are assigned to Sale order or project. I want to inspect the material after receipt for these specific account assignments. I do not want to assign the customer because, my single customer may give different sale orders with different inspection requirements.
But in inspection plan, i can not see the assignment of sale order / project as i can see in Rate Routing.
Can anybody tell me about this?
Regards,
Prashant KolhatkarCreate a Material ONE as Configurable Material. Assign 300 Class Type Class with Charcateristics created through CT04 Transaction which in turn linked to MICs.
Create another Material TWO with same Class but not configurable but is a Variant of Material ONE (MRP 3 View)
Maintain Configuration Profiles for both Materials.
In Material TWO, for insp. type details click on Insp. by Config indicator.
Whenever a Sales Order is created, maintain the requirements from the Customer in Characteristics and save the Sales Order. Against this Sales Order whenever a GR is made for respective Production Order inspection lot is created against the specifications given by Customer and not that maintained in inspection plan.
Best Regards,
K. Raghavendra Nayak -
H323 inspect in a single class with match criteria
Hi, I trying to apply this to make sure only inspect h323 traffic in a single host (that's a Video Conference host), but don't works. Only works when I applied the inspect in the inspection_default class.
Here is the config:
access-list 100 extended permit ip host x.x.x.x any
access-list 100 extended permit ip any host x.x.x.x
class-map h223_VC
match access-list 100
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect ip-options
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect pptp
inspect icmp
inspect netbios
inspect icmp error
class h223_VC
inspect h323 h225
It´s possible? or is something wrong?
Thanks a lot for your helpHi,
When you have it in the global policy you only H323 H225 or you also have H323 ras?
What do you see if you run this commands?
packet-tracer input tcp 1025 1720
sho service-policy flow tcp host host eq 1720
How do you test it?
Luis Silva
"If you need PDI (Planning, Design, Implement) assistance feel free to reach"
http://www.cisco.com/web/partners/tools/pdihd.html -
Help needed in PI sheet requirment
Hello Experts,
We have one specific requirement for PI sheet for our client (4.6 C)
The business want to sendquality information (inspection requirements ) like MIC, Insp. Method,Specifications etc. for 04 inspection lot and they want to see all these information in tabular format on PI sheet
In SAP, there is no standard way to generate instructions for GR inspection characteristics . SO we planned to use user exit to populate the characteristics values in instruction category for inspection.
If we use Repeated data request and table size, we could only populate first MIC and its related information in first row of table and it is getting repeated for multiple rows ( Exit is getting called only once).
We cannot create multiple instructions for each MIC as well , since it will generate individual table for each one .
Has anyone worked on such requirement before ? Any help will be appreciated
Thanks,
Sachin CCREATE OR REPLACE FUNCTION fucntion_name(latA IN NUMBER, longA IN NUMBER, latB IN NUMBER, longB IN NUMBER) RETURN NUMBER
IS
pi CONSTANT NUMBER:=3.14159;
theta NUMBER;
distX NUMBER;
distY NUMBER;
distZ NUMBER;
distP NUMBER;
BEGIN
theta :=longA - longB;
distX :=sin( latA * PI /180) * sin ( latB * PI /180) + cos ( latA * PI/180) * cos ( latB * PI/180) * cos ( theta * PI / 180);
distY :=acos(distX); --this is arc cosine
distZ :=distY * 180/PI; --PI refers to the mathematical PI
distP :=distZ * 60 * 1.1515; --this value should be returned. Of course the intermediate variable names don't matter.
RETURN distP;
END;Edited by: Ora on May 3, 2011 11:46 PM -
With 10% inspection lot has to be created
HI
after procurement of rawmaterial against the purchase requisitionby posting with 101 mvt type lot has to be created with 10%
(ex:if 100 kgs we procured lot has to created in quality with 10 kgs
what is the way
explain
thank u in advanceHi Senthil,
Follow the Below step.
1. Go to QDR1 enter 3char header Press enter.
2. In 2nd screen Enter Decrip and Choose At Lot Creation and Enter reset period 9999
3. Click -> (Arrrow in Top) It will going to New screen.
Create 2 Stage One for Inspection and 2nd for Skip
Stge:1, Insp Sev 4, Tick Ist Enter Description as Inspection required and press enter.
In another small popup screen enter no of Inspection 1 (Bcz your case after 1 Inspection go to SKIP), New Stage as 2, Rej 1, New 1,
Stage2, Tick in SKIP, and Maintain No Skip as 4 (Bcz your case You need inspection after 4 lot) New Stage 1 (Bcz after complete the 4 lot it will go to 1st stage for Inspection.), Rej 1 , New Insp 1.
Save.
Then attach the same thing to Quality Inspection Plan QP01
In Header Detail Screen (2 nd screen) Choose DMR at lot level and assign the your created DMR.
For any query revert.
Regards,
S.Babusingh -
Source inspection configuration
dear all,
what is source inspection and vendor evaluation, please give me details of configuration steps for it.
thanks in advance*What is Source Inspection*
What is source inspection and what are the setup required to do in system to implement successfully?
A source inspection is a quality inspection in which Buyer required the quality check before the material received. So that he performed the quality inspection at the vendoru2019s Location.
To setup source inspection, you should define inspection type (01 and 0101) in material master QM View. (MM01)
When requesting source inspection, include the following information:
a) Purchase order number
b) Item number
c) Part number
d) Quantity of parts to be inspected
e) Date source inspection is required
f) Types of inspection required
- In Process
- Final
- Interim
- First Article Inspection (FAI)
g) Contact name and phone number
Go to transaction QI07 and give the material code, vendor, plant and opening period. When you execute the transaction you would find open purchase orders for the given input data. Select the Purchase Order you wish to perform Source Inspection and choose Create Inspection Lot. These inspection lot triggers for inspection type 0101. Against this inspection Lot perform result recording QE01 & QA11.
When finally you received Goods at your premises, then inspection lot will triggered automatically (01) and perform result recording QE01 & QA11
How to do Source Inspection in QM
Can any one guide how to do Source Inspection in QM. What are the settings required to be done and can the lot for source inspection be trigerred manually or automatically.
The Q-Info Record is used to trigger a source inspection lot for a material/vendor and plant. Under the tab key Inspection Control in Q-Info Record, you would find vendor source Inspection and under that select the inspection type desired for source inspection (say 01,0101) and give the lead time required to perform the inspection in days (say 10 days). If you do not want to trigger an inspection lot @ GR for a source Inspection lot then check the box (Source Insp. No Gr).
Ensure that the inspection type selected @ source inspection is activated in the Material Master Record for the chosen material in the Quality Management View.
To trigger the lot manually you need to have some open purchase orders for the material/plant/vendor. Go to transaction QI07 and give the material code,vendor,plant and opening period. When you execute the transaction you would find open purchase orders for the given input data. Select the Purchase Order you wish to perform S.I and choose Create Inspection Lot.
This would trigger the lot and then it is QE01 & QA11.
Vendor Evaluation for Purchasing
Define the weighting keys in SM30 - V_T147J.
Weighting keys 01 and 02 are defined in the standard system. You combine the following
weighting shares for the standard main criteria:
Main criterion Key 01 Key 02
Price 1 5
Quality 1 5
Delivery 1 2
Gen. service/support 1 1
Ext. service provision 1 2
Define the criteria in SM30 - V_T147G - Double click on the line items
In this step, you define the criteria by which the system computes scores for vendors and
specify whether the scores for the subcriteria are computed manually, semi-automatically, or
automatically.
You can also store your own methods of computation for the scores for subcriteria in the
form of user exits. The enhancement MM06L001 is available for this purpose.
Define the scope of list in SM30 - V_T147M - Double click on the line items
Define Purchasing Organization data for vendor evaluations in transaction OMGL.
An example :-
How the system calculates the score for the automatic subcriteria
"On-Time Delivery Performance"?
The system uses the statistics-relevant delivery date in the purchase order
(Items -> Delivery Schedule) and the goods receipt date to calculate date variances.
You use the statistics-relevant delivery date, for example, if you know that the vendor
will not deliver the material as scheduled on September 15 but on September 30. Enter the
delivery date as September 30, but enter the statistics-relevant delivery date as
September 15.
In calculating the score for on-time delivery performance, the system will then not use
the actual delivery date, but the statistics-relevant delivery date. This has a negative
effect on the score for this goods receipt.
However, materials planning and control uses the realistic delivery date (September 30)
which the vendor will actually adhere to.
The system considers only goods receipts against purchase orders and scheduling agreements
into stores and the release of GR blocked stock into stores. In the standard system, these
are the movement types 101 and 105.
Minimum Delivery Percentage - OMGL in the On-time delivery section
If you do not want a vendor to receive a very good score if he delivered the goods on time,
but did not deliver the required quantity, you can maintain a minimum delivery percentage
in Customizing.
Assume you set the Min. del. perc. parameter to 60% and the vendor delivers the goods on
time, but only 55% of the ordered quantity. Although the goods receipt is punctual, it is
not included in the calculation of the vendoru2019s score for on-time delivery performance. So
that the non-scoring of the on-time delivery performance criterion in this case does not
bring an unfair advantage in comparison with a poor score, the vendor is awarded a low score
for quantity reliability. On-time delivery performance is thus always to be seen in
conjunction with quantity reliability.
Standardizing Delivery Date Variance - OMGL in the On-time delivery section
To rate delivery date variances in days, maintain the Std.del.time var. parameter.
If you assign a lower standard value, this means that relatively low date variances produce
high percentage variances. If you set a higher standard value, this results in a relatively
low percentage variance:
The Std.del.time var. parameter has the value 20. The goods receipt took place on Nov. 27;
the statistical delivery date was Nov. 15. There is thus a difference of 12 days.
The system calculates the percentage variance as follows:
12 / 20 x 100 = 60
If the Std.del.time var. parameter had the value 60, the variance would be 20%
(12 / 60 x 100 = 20).
If you do not maintain this parameter, the system calculates the delivery time variance via
the firm zone in the case of scheduling agreements, and via the order date and the
statistics-relevant delivery date in the case of purchase orders. -
Doing GR for a material type, system should give a message like QI required
Dear Friends
While doing MIGO(GR) for a material type, system should give a message like Quality Inspection required
but Client requirement is not to maintain QM view or Inspection Type 01for material type
Any setting required
Thanks & Regards
GajendranathHi
Please check user exit QBCK0003 |Extended QM check for goods receipt
Regards
sujit
Maybe you are looking for
-
IPod touch will not turn on unless charged
Hi, I have reset my iPod, tried turning off and on again dozens of times but every single time I tried to open an app or attempt to play music when it isn't connected to my computer or plugged it shuts off and will not turn back on until I charge it
-
Does anyone know where I can find speaker stands compatible with the SBS 560? Thanks in advance!
-
How to start a new career in SAP - SD as a Fresher?
Dear All, I am on the way to enter in the new world - SAP as a fresher. Seems to be positive and hopes on own capabilities. Willing to learn and go for Sales & Distribution (SD) Module as per my experience and domain knowledge. Please input your expe
-
Media Encoder QT can't be imported
I have some watchfolders configured in Media Encoder CS6. I created a QT Ref from a TGA Image Sequence with QT 7 and when I try to convert it, Media Encoder sais that the file could not be imported please check setting and try again....I tried with a
-
I am having a grid. when ever filling the form and click on add button then that information is added into a row in that grid.I am having a refresh button, on clicking on that the whole information will be cleared.I done this, but when i am adding an