SIP TLS/sRTP on Cisco border router (CUBE)

Hello!
Need help configuring SIP TLS for Skype Connect on CUBE (Cisco 2821, 15.1 IOS). Maybe someone has already set up at a similar functionality. Particularly interested in the question about the CA-signed certificate (maintain, installation).

I think you need to post here: https://communities.cisco.com/community/developer

Similar Messages

Cisco 877 router - Cisco IP phone won't register with SIP provider

Hi all,
I'm having a problem with a Cisco SPA504G phone not registering with the SIP carrier over the Internet. We've recently rolled out a Cisco 877 router onto a new NBN business connection and can't get the pre-configured IP phone to register.
When we tested the phone with the NBN-provided Netgear router, it worked fine, as it did with the previous Cisco 1841 router we were using on a different link.
The way it's setup is using VLANs to define the internal subnets, which are then assigned to the physical interfaces (since the 887 doesn't allow IP assignments to the interfaces directly).
VLAN 100 is the internal network and has a SBS2011 server – assigned to F0 – IP range is 192.168.1.0
VLAN 200 is the guest network and has Internet access only – assigned to F1 – IP range is 10.1.1.0
VLAN 500 is the WAN network and connects to the NBN upstream box – assigned to F3 – external IP address assigned by DHCP
I've been playing around with access lists, nat rules, basically everything in my limited Cisco knowledge to try and figure this out, but to no avail. I have even configured what I believe is unrestricted access to IP, UDP and TCP outbound and inbound to all VLANs and still can't get it to register.
Tried isolating the issue by creating a new VLAN and assigning it to the spare interface and basically allowing everything in and out, but still no luck.
The problem has to be something on the router – probably some small line of config I haven’t removed or added.
I am going to pull my hair out soon, so would really appreciate some assistance from the Cisco gurus out there.
My client has just purchased about 10 of these handsets from their provider so I need to fix this ASAP. The guy who provided them wasn't very helpful, and basically said I'm on my own once we tested using the NBN-provided Netgear router.
Happy to post my config as well.
Please help!!!!

Current configuration : 4912 bytes
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router1
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
no ip source-route
ip dhcp excluded-address 10.1.1.1
ip dhcp pool GUEST
network 10.1.1.0 255.255.255.0
dns-server 10.1.1.1 203.50.2.71 139.130.4.4
default-router 10.1.1.1
ip cef
no ip domain lookup
ip domain name network.local
ip name-server 192.168.1.123
ip name-server 203.23.53.12
ip name-server 197.12.32.86
ip name-server 8.8.8.8
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGL171220XY
username admin privilege 15 secret 5 $1$aNsm$N1BCQYkoi8gnURyvloYEX/
controller VDSL 0
interface Ethernet0
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
bridge-group 10
pvc 8/35
interface FastEthernet0
description NAC - Internal network
switchport access vlan 100
no ip address
interface FastEthernet1
description NAC - Guest network
switchport access vlan 200
no ip address
interface FastEthernet2
no ip address
shutdown
interface FastEthernet3
description **** WAN Port ****
switchport access vlan 500
no ip address
interface Vlan1
no ip address
bridge-group 10
hold-queue 100 out
interface Vlan100
description NAC - Internal Vlan
ip address 192.168.1.1 255.255.255.0
ip access-group IN-100 in
ip access-group OUT-100 out
ip nat inside
ip virtual-reassembly in
interface Vlan200
description NAC - Guest Vlan
ip address 10.1.1.1 255.255.255.0
ip access-group IN-200 in
ip access-group OUT-200 out
ip nat inside
ip virtual-reassembly in
interface Vlan500
description **** WAN Vlan ****
ip address dhcp
ip nat outside
no ip virtual-reassembly in
no ip forward-protocol nd
ip http server
ip http access-class 23
ip http secure-server
ip dns server
ip nat inside source list NAT-100 interface Vlan500 overload
ip nat inside source list NAT-200 interface Vlan500 overload
ip nat inside source static tcp 192.168.1.123 25 interface Vlan500 25
ip nat inside source static tcp 192.168.1.123 443 interface Vlan500 443
ip nat inside source static tcp 192.168.1.123 3389 interface Vlan500 3399
ip nat inside source static tcp 192.168.1.123 80 interface Vlan500 80
ip nat inside source static tcp 192.168.1.123 4125 interface Vlan500 4125
ip nat inside source static tcp 192.168.1.124 3389 interface Vlan500 3390
ip nat inside source static tcp 192.168.1.123 987 interface Vlan500 987
ip nat inside source static tcp 192.168.1.123 1723 interface Vlan500 1723
ip route 0.0.0.0 0.0.0.0 55.234.52.43
ip access-list extended IN-100
permit udp any any range bootps bootpc
deny ip 10.1.1.0 0.0.0.255 any
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended IN-200
permit udp any any range bootps bootpc
permit ip 10.1.1.0 0.0.0.255 any
ip access-list extended NAT-100
deny ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended NAT-200
deny ip 10.1.0.0 0.0.255.255 10.1.0.0 0.0.255.255
permit ip 10.1.1.0 0.0.0.255 any
ip access-list extended OUT-100
permit udp any range bootps bootpc any
deny ip 10.1.1.0 0.0.0.255 any
permit ip any 192.168.1.0 0.0.0.255
ip access-list extended OUT-200
permit udp any range bootps bootpc any
deny ip 10.1.1.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip any 10.1.1.0 0.0.0.255
access-list 23 permit 59.23.164.52
access-list 23 permit 192.168.1.0 0.0.0.255
access-list 23 permit 10.1.1.0 0.0.0.255
access-list 23 permit 120.146.0.0 0.0.255.255
access-list 23 permit 149.185.12.0 0.0.0.255
access-list 23 permit 110.44.28.0 0.0.0.255
access-list 23 permit 110.44.26.0 0.0.0.255
access-list 23 permit 103.25.212.0 0.0.0.255
access-list 23 permit any
bridge 10 protocol ieee
banner motd ^C
* Authorized personnel only! *
^C
line con 0
login local
no modem enable
line aux 0
line vty 0 4
password password01
login local
transport input all
end

VCS X8.5.1 SIP TLS to CUCM 8.6.2

I'm having problems enabling TLS on my SIP trunk from the VCS to CUCM.
The SIP trunk shows active on the VCS, but I can't make calls from VCS to CUCM or from CUCM to VCS.
Before configuring TLS, I was able to make these calls.
With TLS enabled, the VCS search for calls from VCS to CUCM show the call rejected and give the reason "Forbidden"
Calls from CUCM to VCS get fast busy and I do not see anything in the search history on the VCS.
I've restarted the trunk and call manager service on the CUCM servers, but no change.
I'm not really sure where to go from here.
I followed the following guide for configuring the SIP trunk. http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/X8-5/Cisco-VCS-SIP-Trunk-to-Unified-CM-Deployment-Guide-CUCM-8-9-10-and-X8-5.pdf
Any help is appreciated.
Thanks,
Joe

I have again checked these and identical to what I set up, We have a multiple TX9000's on the CUCM in Secure mode working perfect and can make Encrypted calls to the TPS server via a TPS TCP Trunk.
but any calls to the VCS just fail on a VCS To CUCM Trunk using TLS with a fast busy signal. and the VCS doesn't even show a search history for it.
In the eyes of the VCS and the CUCM there is no Issues with the TLS SIP Trunk it seems to be working, but It seems SIP TLS packets don't even leave the CUCM. I have tried almost every resource known, and thought it was me just having some random issue until I saw Josef post the same issue.
Tomorrow I will check the X.509 names on the CUCM SIP Security Profile as this is the only thing I can think of that might cause the SIP trunk to be OK up but not route correctly maybe?

Cisco 877W router and external ADSL modem

Cisco 877W router and external ADSL modem
In order to support ADSL2+ on a pre ADSL2+ router and in preparation for a later migration to BT infinity I am trying to configure the Router using an external adsl2+ modem appropriately.
The original configuration had 3 ports configured as one (internal lan) vlan and bridge group together with one wireless sub-interface, the remaining port configured a second vlan and bridge group with a second wireless sub- interface. The Dialer was a member of the second bridge group. This way the second wireless interface and associated bridge group provided a kind of DMZ for outbound access.
The configuration I am attempting is similar the lan ports remain the same, but port 0 as a member of the vlan and bridge group (now a pppoe client) associated with one of the wireless sub interfaces as per above. The ATM interface is downed. This nearly works except that if the wireless subinterface on this bridge group is configured the dialer no longer dials giving a 'no dialer string' error. If I do not configure that wireless sub interface all works well.
If anyone is interested to look I would appreciate any comments. I enclose a sanitised config in which you will note the 'commented out' wireless subnet interface (in red).
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname xxxxxxxxxxxxxxxxxxxxx
boot-start-marker
boot-end-marker
logging buffered 4096 warnings
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxx
aaa new-model
aaa group server radius sdm-vpn-server-group-2
aaa group server radius rad_eap
server 192.168.253.1 auth-port 1812 acct-port 1813
server 192.168.253.1 auth-port 1645 acct-port 1646
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_2 group sdm-vpn-server-group-2
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa authorization network sdm_vpn_group_ml_2 local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone PCTime 0
clock summer-time PCTime date Mar 30 2003 1:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-2834265337
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2834265337
revocation-check none
rsakeypair TP-self-signed-2834265337
crypto pki certificate chain TP-self-signed-2834265337
certificate self-signed 01 nvram:IOS-Self-Sig#2F.cer
dot11 syslog
dot11 ssid GuestAP
   vlan 101
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 113B162712001F4A2D2B25
dot11 ssid LanAP
   vlan 100
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
   mbssid guest-mode
no ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.252.1 192.168.252.8
ip dhcp excluded-address 192.168.252.15 192.168.252.254
ip dhcp pool sdm-pool1
   import all
   network 192.168.252.0 255.255.255.0
   domain-name XXX.Local
   dns-server xxx.xxx.xxx.xxx
   default-router 192.168.252.254
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
no ip bootp server
no ip domain lookup
ip domain name XXX.Local
ip name-server xxx.xxx.xxx.xxx
ip name-server xxx.xxx.xxx.xxx
ip reflexive-list timeout 120
vpdn enable
vpdn-group 1
request-dialin
protocol pppoe
username administrator privilege 15 secret 5 £££££££££££££££££££££
class-map type inspect match-any IN_to_OUT_CLASS
match protocol tcp
match protocol udp
match protocol icmp
class-map type inspect match-any OUT_to_IN_CLASS
match protocol https
match protocol smtp extended
class-map type inspect match-any DMZ_to_IN_CLASS
match protocol http
match protocol https
match protocol smtp extended
policy-map type inspect DMZ_to_IN_POL
class type inspect DMZ_to_IN_CLASS
inspect
class class-default
drop log
policy-map type inspect IN_to_OUT_POL
class type inspect IN_to_OUT_CLASS
inspect
class class-default
drop log
policy-map type inspect OUT_to_IN_POL
class type inspect OUT_to_IN_CLASS
inspect
class class-default
drop log
zone security INSIDE
zone security OUTSIDE
zone security DMZ
zone-pair security OUT_TO_IN source OUTSIDE destination INSIDE
service-policy type inspect OUT_to_IN_POL
zone-pair security IN_TO_OUT source INSIDE destination OUTSIDE
service-policy type inspect IN_to_OUT_POL
zone-pair security DMZ_TO_OUT source DMZ destination OUTSIDE
service-policy type inspect IN_to_OUT_POL
zone-pair security DMZ_TO_IN source DMZ destination INSIDE
service-policy type inspect DMZ_to_IN_POL
bridge irb
interface Loopback0
no ip address
interface Null0
no ip unreachables
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
interface FastEthernet0
description Outside Interface (PPPoE)
interface FastEthernet1
description Inside Interface
switchport access vlan 10
interface FastEthernet2
description Inside Interface
switchport access vlan 10
spanning-tree portfast
interface FastEthernet3
description Inside Interface
switchport access vlan 10
spanning-tree portfast
interface Dot11Radio0
no ip address
no ip route-cache cef
no ip route-cache
encryption vlan 100 mode ciphers aes-ccm tkip
encryption vlan 101 mode ciphers aes-ccm tkip
ssid GuestAP
ssid LanAP
mbssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2437
station-role root
interface Dot11Radio0.100
description LanAP
encapsulation dot1Q 100
no ip route-cache
no cdp enable
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 spanning-disabled
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
!interface Dot11Radio0.101
! description GuestAP
! encapsulation dot1Q 101
! no ip route-cache
! no cdp enable
! bridge-group 1
! bridge-group 1 subscriber-loop-control
! bridge-group 1 spanning-disabled
! bridge-group 1 block-unknown-source
! no bridge-group 1 source-learning
! no bridge-group 1 unicast-flooding
interface Vlan1
description $ES_LAN$
no ip address
ip virtual-reassembly
pppoe enable group global
pppoe-client dial-pool-number 1
bridge-group 1
interface Vlan10
no ip address
ip virtual-reassembly
bridge-group 10
interface Dialer1
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nat outside
ip virtual-reassembly
zone-member security OUTSIDE
encapsulation ppp
ip route-cache flow
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXXX
ppp chap password 7 xxxxxxxxxxxxxxxxxxx
ppp pap sent-username xxxxxxxxxxxxxxxxxx password 7 xxxxxxxxxxxxxxxxxxxxx
ppp ipcp dns request
ppp ipcp wins request
hold-queue 224 in
interface Dialer0
no ip address
interface BVI10
description Inside Interface
ip address 192.168.253.254 255.255.255.0
ip access-group 101 in
ip helper-address 192.168.253.1
ip nat inside
ip virtual-reassembly
zone-member security INSIDE
interface BVI1
description DMZ Interface
ip address 192.168.252.254 255.255.255.0
ip nat inside
ip virtual-reassembly
zone-member security DMZ
ip local pool SDM_POOL_1 192.168.20.9 192.168.20.14
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http access-class 1
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip nat inside source list Inside_Clients_NAT interface Dialer1 overload
ip nat inside source static 192.168.253.10 xxx.xxx.xxx.xxx
ip access-list extended DMZ_to_IN_POL
remark SDM_ACL Category=128
permit ip any any
ip access-list extended Inside_Clients_NAT
remark SDM_ACL Category=2
permit ip 192.168.253.0 0.0.0.255 any
logging 192.168.253.10
access-list 1 remark Auto generated by SDM Management Access feature
access-list 1 remark SDM_ACL Category=1
access-list 1 permit 192.168.253.0 0.0.0.255
access-list 100 remark VTY Access-class list
access-list 100 remark SDM_ACL Category=1
access-list 100 permit ip 192.168.253.0 0.0.0.255 any
access-list 100 deny   ip any any
access-list 101 remark Auto generated by SDM Management Access feature
access-list 101 remark SDM_ACL Category=1
access-list 101 remark Auto generated by SDM for NTP (123) xxx.xxx.xxx.xxx
access-list 101 permit udp host xxx.xxx.xxx.xxx eq ntp host 192.168.253.254 eq ntp
access-list 101 permit tcp 192.168.253.0 0.0.0.255 host 192.168.253.254 eq telnet
access-list 101 permit tcp 192.168.253.0 0.0.0.255 host 192.168.253.254 eq 22
access-list 101 permit tcp 192.168.253.0 0.0.0.255 host 192.168.253.254 eq www
access-list 101 permit tcp 192.168.253.0 0.0.0.255 host 192.168.253.254 eq 443
access-list 101 permit tcp 192.168.253.0 0.0.0.255 host 192.168.253.254 eq cmd
access-list 101 deny   tcp any host 192.168.253.254 eq telnet
access-list 101 deny   tcp any host 192.168.253.254 eq 22
access-list 101 deny   tcp any host 192.168.253.254 eq www
access-list 101 deny   tcp any host 192.168.253.254 eq 443
access-list 101 deny   tcp any host 192.168.253.254 eq cmd
access-list 101 deny   udp any host 192.168.253.254 eq snmp
access-list 101 permit ip any any
access-list 199 permit ip any host 10.1.1.1
dialer-list 1 protocol ip permit
no cdp run
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.253.1 auth-port 1812 acct-port 1813 key 7 XXXXXXXXXXXXXXXXXX
radius-server host 192.168.253.1 auth-port 1645 acct-port 1646 key 7 XXXXXXXXXXXXXXXXXX
radius-server vsa send accounting
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 10 protocol ieee
bridge 10 route ip
banner login C Border Router
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
access-class 100 in
privilege level 15
length 0
transport input telnet ssh
scheduler max-task-time 5000
scheduler interval 500
ntp server xxx.xxx.xxx.xxx source Dialer0 prefer
ntp server xxx.xxx.xxx.xxx source Dialer0 prefer
sntp server xxx.xxx.xxx.xxx
end

Hi Jody,
Apologies delay in replying. I have done the following:
Made two of the FE ports vlan1,BVI1 (for LAN traffic)
Left one port as VLAN10 as the pppoe client conected to the externalmodem
Made the last port VLAN10 as well and gave it an IP addess as for a DMZ client.
I have DHCP configured to serve the DMZ addresses.
This all works for LAN clients and also works for a client attachedto that physical DMZ port.
When I added a dot11radio sub interface into VLAN 10 the wireless client did not get an IP lease. Everything else continued to work.
I had never thought about this before, but if a dot11radio interface is on the same vlan (but not being part ofa bridge group) why are DHCP broadcasts not propogating to all the vlan members as I would have expected. I recognise that this isa limit in my understanding.
If I then made VLAN10 a member of a new Bridge Group, I lost WAN connectivity as per original posting.
I cannot add another VLAN due to the 2 vlan limit in this image.
Finally regarding your comment about giving it what it wants, what exactly did you have in mind. The dialer already has a dial string parameters configured.
Think I am about to give upon this.
Regards,

Cisco 878 router for ADSL connectivity

Hi All,
I got a Cisco 878-k9 G.SHDSL router. I am trying to configure to get connectivity to my Service Provider.
Earlier i have configured Cisco 877 router serval times. But Cisco 878 for the first time. There is a DSL
controller in 878 rtr. I think i m missing something somewhere.
Below is the config that i have done
controller DSL 0
mode atm
loopback digital
dsl-mode shdsl symmetric annex A
line-rate auto
line-term cpe
line-mode 2-wire line-one
ip cef
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp pool INSIDE-Pool
   import all
   network 192.168.10.0 255.255.255.0
   default-router 192.168.10.1
   dns-server 212.77.192.59 212.77.192.60
   lease 8
interface ATM0
description (Outside Public Interface)
no shutdown
no ip address
load-interval 30
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer0
ip address negotiated
no ip redirects
no ip proxy-arp
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname p4411XXXX
ppp chap password qatarXXXX
ppp pap sent-username p44114032 password 0 qatarXXXX
no sh
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
ip nat inside source list 101 interface Dialer0 overload
access-list 1 permit any
access-list 101 deny ip 192.168.0.0 0.0.255.255 10.10.0.0 0.0.255.255
access-list 101 permit ip 192.168.0.0 0.0.255.255 any
dialer-list 1 protocol ip permit

i have an adsl line
i try to configure the router 878
but no connection ,, kann u tel me how do u have resolve the probleme please
this is the running config
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname cisco2
boot-start-marker
boot-end-marker
no logging buffered
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
resource policy
clock timezone EST -5
clock summer-time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 2:00
ip subnet-zero
ip cef
ip name-server 212.217.0.1
ip name-server 212.217.0.12
ip name-server 212.217.1.1
ip ddns update method sdm_ddns1
DDNS both
vpdn enable
vpdn-group pppoe
crypto pki trustpoint TP-self-signed-201735762
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-201735762
revocation-check none
rsakeypair TP-self-signed-201735762
crypto pki certificate chain TP-self-signed-201735762
certificate self-signed 01
3082023D 308201A6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32303137 33353736 32301E17 0D303230 33303130 32353235
375A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3230 31373335
37363230 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
A62304BC 27194971 2A4FAEB3 9D57240E 26EDED2A 1674FF9A 7CBBB8F2 85245C3B
C4DDBBF8 F8A67D31 5FDCBD11 72A2735D 9E8FC84B 17B55C71 43C10E41 ACC50BEC
FCE8D9EE 6D2B0B55 9BD5B62C 3981506F 04B92C25 CA4C307E BC6A6A5F 4FBEF0EE
05FEFA57 C7D879FD 79EF442F 121D6393 57E96F31 5414D1D5 4FADFBC0 95C9EAB3
02030100 01A36730 65300F06 03551D13 0101FF04 05300301 01FF3012 0603551D
11040B30 09820763 6973636F 322E301F 0603551D 23041830 16801418 6C8FED13
FFD7B2FB F6FA47E7 682B0093 FAE2AC30 1D060355 1D0E0416 0414186C 8FED13FF
D7B2FBF6 FA47E768 2B0093FA E2AC300D 06092A86 4886F70D 01010405 00038181
007C867C AC28A7F0 4BDD261C 81A71F1D E0671C28 F4724F5D ED1FE702 BCE234D9
1F85FE90 4D0AD23E 9904CBF9 D44A8CD5 0F5515BB 8FEEE4BB FF9795E1 7770B60A
E37455CC D6606EAF E0EAEEA4 932F55E6 91C6F87F 1D022203 08AD7C78 4DCF5AEA
819D2367 2B5054CC 695A4EF5 BC9ADA26 F7803106 E94BD666 179EB3DF 4CDE4CB8 1C
quit
username xxxxx privilege 15 password 0 xxxxx
controller DSL 0
mode atm
line-term co
line-mode 4-wire standard
dsl-mode shdsl symmetric annex B
ignore-error-duration 15
line-rate 4608
interface BRI0
no ip address
encapsulation hdlc
shutdown
interface ATM0
no ip address
ip nat outside
ip virtual-reassembly
no atm ilmi-keepalive
interface ATM0.1 point-to-point
pvc 8/35
pppoe-client dial-pool-number 1
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
description lan
ip address 192.168.1.5 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip route-cache flow
ip tcp adjust-mss 1412
interface Dialer1
ip ddns update hostname xxxx.dyndns.org
ip ddns update sdm_ddns1
ip address negotiated
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname xxxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxxx password 0 xxxxx
interface Dialer0
no ip address
ip classless
ip http server
ip http access-class 24
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip access-list extended to-sip-servers
remark --- traffic to any sip server
permit udp 192.168.1.0 0.0.0.255 any eq 5060
access-list 1 permit 0.0.0.0 255.255.255.0
access-list 1 permit 192.168.1.0 0.0.0.255
dialer-list 1 protocol ip permit
snmp-server community public RO
no cdp run
control-plane
banner motd ^CINE welcome
banner ^C
line con 0
no modem enable
line aux 0
line vty 0 4
password cisco
scheduler max-task-time 5000
end

Increase performance of Border Router

Is there any way to increase the performance of a PFR Border Router Cisco 7206 VRX?. What would be the best or most viable. Thank you.

Hi Somaraju,
There are many ways to increase the WAS performance. You
can use the Config Tool or increase the no. of server
processes. Below threads might be of help.
Re: Increasing Heap Size not possible
Re: Problem with Java.lang.outofmemoryerror
max number of server processes
Please check in the log files as to why exactly the
server is restarting and try the above mentined solutions.
Regards
Srikishan

Cisco ASR 1006 Cube license

Dears,
i have cisco asr router 1006 and i need to check the license cube license.
i tried show license but it doesnt accept the command.
Please advise how to check the cube license and its ersial number.
BR,
Haytham

Have you tried...
show facility-alarm status
to identify what the critical alarm is and then fix.
You may be able to also use
clear facility-alarm
However, most likely it could be some issue such as failed power supply, etc that will not clear.

ACE - SIP TLS

Hello,
Do you know if it is possible in ACE 4710 appliance to configure a SIP TLS probes?
The SIP probe we have in the configuration guide it is only for clear text.
Anyways, for Lync 2013 we need to establish first a TLS session and then within it, send an SIP request...
IS it possible in any version? I tried also to configure a HTTPS probe but it fails as it sends a GET which the Lync SIP server doesnt understand..
Thanks for your help
Giulio

hi Giulio,
you probably need a custom script, contact your Cisco Account Manager or System Engineer they can help you with it
Cesar R
ANS Team

I am loosing configuration when I power off my Cisco 857 router

I bought new Cisco 857 router from the shop. Router must have been used before as I couln't go in with default username/password cisco/cisco.
Well I followed instruciton and reset password to username and password. Now I finally connected to the Cisco CP express over my IE browser.
I found out that somebody was using a router from the shop so this is why I coun't log to it in the first place. Anyway problem is that when I changed configuration and applied settings it remembers it until I power it off. When I power it on again it remembers all settings from that shop.
It reverts everything back: IP address, previous level 15 account and password - everything like after password reset.
I tried it again and it again lost settings. So I found following instruction:
http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed again all settings on the router. My settings are again lost after power off/on. I noticed that when I do first bit it does show
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enableCisco#show startUsing 3359 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Cisco!boot-start-markerboot-end-marker!logging buffered 51200 warningsenable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.!no aaa new-model!crypto pki trustpoint TP-self-signed-3185909327 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3185909327 revocation-check none rsakeypair TP-self-signed-3185909327!!crypto pki certificate chain TP-self-signed-3185909327 certificate self-signed 01 nvram:IOS-Self-Sig#5.cerdot11 syslogno ip dhcp use vrf connectedip dhcp excluded-address 10.10.10.1!ip dhcp pool ccp-pool   import all   network 10.10.10.0 255.255.255.248   default-router 10.10.10.1   lease 0 2!!ip cefno ip domain lookupip domain name molinary.com!!!username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.username username privilege 15 password 0 password!!archive log config hidekeys!!!!!interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto!interface ATM0.1 point-to-point description $ES_WAN$ ip nat outside ip virtual-reassembly pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$ ip address 10.10.10.1 255.255.255.248 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452!interface Dialer0 ip address dhcp encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname [email protected] ppp chap password 0 netgear01 ppp pap sent-username [email protected] password 0 netgear01!ip forward-protocol nd!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000ip nat inside source list 1 interface ATM0.1 overload!access-list 1 remark INSIDE_IF=Vlan1access-list 1 remark CCP_ACL Category=2access-list 1 permit 10.10.10.0 0.0.0.7dialer-list 1 protocol ip permitno cdp run!control-plane!banner exec ^C% Password expiration warning.-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this deviceand it provides the default username "cisco" for one-time use. If you havealready used the username "cisco" to login to the router and your IOS imagesupports the "one-time" user option, then this username has already expired.You will not be able to login to the router with this username after you exitthis session.It is strongly suggested that you create a new username with a privilege levelof 15 using the following command.username <myuser> privilege 15 secret 0 <mypassword>Replace <myuser> and <mypassword> with the username and password youwant to use.-----------------------------------------------------------------------^Cbanner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C!line con 0 login local no modem enableline aux 0line vty 0 4 privilege level 15 login local transport input telnet ssh!scheduler max-task-time 5000endCisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#show versionCisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARECisco uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)Configuration register is 0x2102Cisco#Cisco#Cisco#Cisco#endTranslating "end"% Unknown command or computer name, or unable to find computer addressCisco#reloadProceed with reload? [confirm]*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. Reload Reason: Reload Command.System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARETechnical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memoryBooting flash:/c850-advsecurityk9-mz.124-15.T12.binSelf decompressing the image : ############################################## [OK]              Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.           cisco Systems, Inc.           170 West Tasman Drive           San Jose, California 95134-1706Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814E7240This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)no ip dhcp use vrf connected               ^% Invalid input detected at '^' marker.SETUP: new interface NVI0 placed in "shutdown" statePress RETURN to get started!*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state toup*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_team*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoinga cold start*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state toup*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state toup*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state toup*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3, changed state to down*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2, changed state to down*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1, changed state to down*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upAuthorized access only!===========================================
Please help me as I am stuck and can't go any further....

Hi David White,
Alternatively, after password recovery you can modify the configuration to be what you want, and then issue:
   write memory
to save the configuration. You can then verify that your changes have been saved to the startup config by issuing:
   show startup-config"
The only good thing is that when I switch off a router it erase configuration except my new password which I created after password reset. Everything else is getting vanished (ADSL settings, DHCP, routing ) everything. Even new admin accounts I created.
Well have a question to your above comments. I am new in Cisco so please put as much detail as you can for me to understand. When you say modify configuration do you mean to go to Cisco CP Express graphical interface and then connect router to hyper terminal and execute above commands?
Why router doesn't remember this anyway. There must be some option to change in configuration to make thing permanent when I hit apply changes in Cisco CO Express otherwise it is pointless to heve it.
Phillip
write memory
is
copy running-config startup-config"
Can't this be done via Cisco CP Express or set up router to copy this every time I change this in graphical interface rather going to command line to achnoledge it?
I understand your concern about this router and somebodie's configuration details as you want things to be un-used when you buy them - true. ADSL details belongs to the shop which sold me the router so that is why I don't make a big problem about this. We take most of hardware from this shop and have discount and many good deals with them so I think they have been just testing it and forgot to erease their config. It might be that someone has returned router to the shop and they have repaired it and tested it.
I hope this is a normal behaviour of this router as I have option to replace it in case this is a fault.
Could you please write me step by step guide how can I make changed options stay permanently on router?
thank you
Dragan

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

Cisco 2951 router AC-PoE power consumption, meaning of the mention "Platform Only" in the datasheet.

Hello,
I have a question regarding the power consumption of a Cisco 2951 router with an AC-PoE power supply (without PoE boost).
In fact in the table (n°7) of the Cisco 2900 Series ISR (G2) datasheet, that sum up the power consumption data for Cisco 2900 series routers there is the line : "Maximum Power with PoE Power Supply (Platform Only) (Watts)", and I would like to know what is exactly the meaning about the mention "Platform Only".
Thank you for your help, best regards,

Hi @francois.trarieux,
This is the maximum power that is consumed exclusively by the router from the PoE PS (Power Supply). The power capacity that the PoE PS gives to other PoE devices (IP Phones, Cameras, APs, etc) is specified in the line below "Maximum End-Point PoE Power Available from PoE Power Supply (Watts)" of the datasheet.
HTH.
Regards,
Martin, IT Specialist

Configuration Issue with my Cisco 871 Router

Hi all,
I am a newbie to the Cisco IOS.
I got a Cisco 871 Router that I'd like to use for internet connection. My LAN network is 192.168.1.0/24 and the ISP has assigned us the IP 41.212.79.108/24 and gateway 41.212.79.1.
With my current configuration, I can hit the router - 192.168.1.1 - and it's WAN port - 41.212.79.108 - but not the gateway.
Below is my current config:
Hoggers#show config
Using 4414 out of 131072 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Hoggers
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 **********************.
no aaa new-model
crypto pki trustpoint TP-self-signed-568493463
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-568493463
revocation-check none
rsakeypair TP-self-signed-568493463
crypto pki certificate chain TP-self-signed-568493463
certificate self-signed 01 nvram:IOS-Self-Sig#7.cer
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 192.168.1.2
ip dhcp excluded-address 192.168.1.3
ip dhcp excluded-address 192.168.1.4
ip dhcp excluded-address 192.168.1.5
ip dhcp excluded-address 192.168.1.6
ip dhcp excluded-address 192.168.1.7
ip dhcp excluded-address 192.168.1.8
ip dhcp excluded-address 192.168.1.9
ip dhcp excluded-address 192.168.1.10
ip dhcp excluded-address 192.168.1.100
ip dhcp excluded-address 192.168.1.90
ip dhcp pool ccp-pool
   import all
   network 10.10.10.0 255.255.255.248
   default-router 10.10.10.1
   lease 0 2
ip dhcp pool LANPOOL
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 41.212.3.2 41.212.3.253
ip domain name yourdomain.com
ip name-server 41.212.3.2
ip name-server 41.212.3.253
archive
log config
hidekeys
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description Wan to Outside World
ip address 41.212.79.108 255.255.255.0
duplex auto
speed auto
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 192.168.1.1 255.255.255.0
ip tcp adjust-mss 1452
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 41.212.79.1
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source static tcp 192.168.1.31 80 interface FastEthernet4 80
access-list 23 permit 10.10.10.0 0.0.0.7
no cdp run
control-plane
scheduler max-task-time 5000
end
I'll appreciate any light you can shed on what am missing.

2 wireless routers can not communicate wirelessly with each other.
You need to connect cable between 2 routers and use the second wireless router as access point.
Follow this link to connect Linksys router to another router.
Some of your devices are getting same IP address. This might be the issue with DHCP server of the router. You can try DHCP reservation on the router so that each device will get unique IP address.

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

What are the ideal settings for my TC with Shaw's Cisco DPC3825 router/modem

My old 2nd Gen Time Capsule crapped out and now I am about to set up my new 2TB TC. My provider is Shaw Communications and they have upgraded me to their Broadband 100 Mbps service. This came with a new modem/router combo made by Cisco and is model DPC3825. Before I start plugging things in I'd like to know what are the ideal settings such that I gain the most of the BB100 service. Should I be setting the Cisco modem/router to Bridge mode or the TC? Should I have Shaw disable anything? Any insight is greatly appreciated.

Unless you specifically need to have the TC perform as the main router for your network, life will be a lot easier if you configure the TC to operate in Bridge Mode.
Whether the Cisco modem/router or gateway can possibly be configured to act as a simple bridge mode modem is one thing to consider.
Whether Shaw would support you in the event of any connection difficulties with the modem/router configured this way is another.
Since Shaw is your provider, it might make sense to talk with them about best practice as far as configuring the DPC3825.
Once you have that information in hand, you will then have the answer on how best to configure the TC.....which will very likely be in Bridge Mode.

Problem with Cisco 861W router and outgoing VPN

We have a Cisco 861W router that is blocking an outgoing PPTP on the internal access point only. The outgoing VPN works when the traffic is through a wired connection or the connection is on another access point. We fail to make a connection only when connection to the 861W's internal Access Point.
Here is the Access Point Configuration:
Current configuration : 2100 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname obap
enable secret 5 $1$.1RF$go1D7WITXUn3s8TUaw3tC.
no aaa new-model
dot11 syslog
dot11 ssid OLIVER
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 0 XXXXXXXXXXX
username XXXXXX privilege 15 secret 5 $1$Wc0K$OzcQDDQfjHP6La31eXMoG/
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid OLIVER
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecti
ng AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
banner login ^CC
% Password change notice.
Default username/password setup on AP is cisco/cisco with priv¾ilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
^C
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
cns dhcp
end
obap#
Here is the Router's Configuration:
Current configuration : 5908 bytes
! No configuration change since last restart
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname obrouter
boot-start-marker
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 $1$i9XE$DjxFVAEC9nC4/r6EQKCd6/
no aaa new-model
memory-size iomem 10
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-1856757619
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1856757619
revocation-check none
rsakeypair TP-self-signed-1856757619
crypto pki certificate chain TP-self-signed-1856757619
certificate self-signed 01
3082024D 308201B6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383536 37353736 3139301E 170D3036 30313032 31323030
34345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38353637
35373631 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B1A4 FB786547 3D582260 03DB768D 116BDE9A 309FBA04 B53F77B0 BFE32344
7C3439B3 97192B36 760A9411 1D5C7549 8D86F532 ABA44F53 0D08B7F4 A9A747D5
071330C3 65BF25A8 927F3596 29BB5A80 90C8D169 22268476 3B8DDE1E FDB7170D
B4820D03 5580A849 A92C7E76 9AC10867 505A2FEE 64360741 7F9DBDBF 3D79982C
F81D0203 010001A3 75307330 0F060355 1D130101 FF040530 030101FF 30200603
551D1104 19301782 156F6272 6F757465 722E6272 75736868 6F672E63 6F6D301F
0603551D 23041830 168014D8 5BC2FFB2 967A4C7B 11B44122 5C8D31F7 749B9230
1D060355 1D0E0416 0414D85B C2FFB296 7A4C7B11 B441225C 8D31F774 9B92300D
06092A86 4886F70D 01010405 00038181 005901F1 C239074B B8213567 CF7B65BF
DAFE4557 69B2A3B1 5F2593C7 A54B9598 23FD5E7A 563AA6E0 AFB25801 FA0061E8
F9545372 DB600B3A BE68AE65 1EDA593E 6A0C96B8 5A4136AF 393F9AAC 651E1C36
B8B7C6C0 47936C24 D2ECE9A5 9446EE32 FC7461FA AD8CF1CE A7FBF341 07E9C3C6
505AB88D 0E7FCAFC 5792298A E5E4D1FE CC
        quit
no ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.99
ip dhcp pool ccp-pool1
   import all
   network 192.168.0.0 255.255.255.0
   dns-server 216.49.160.10 216.49.160.66
   default-router 192.168.0.1
ip cef
no ip bootp server
ip domain name brushhog.com
ip name-server 216.49.160.10
ip name-server 216.49.160.66
license udi pid CISCO861W-GN-A-K9 sn FTX155281FY
username tech38 privilege 15 secret 5 $1$d/4Z$n/23EsXbzfHF5XfJ8Nv.y0
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
duplex auto
speed auto
pppoe-client dial-pool-number 1
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXXXXXXXXX
ppp chap password 7 XXXXXXXXXXXXXXXX
ppp pap sent-username XXXXXXXXXXXXXX password 7 XXXXXXXXXXX
no cdp enable
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static tcp 192.168.0.25 80 interface Dialer0 80
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Any help would be appreciated

Hello,
i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Can someone help?
Thank you.
Here is my config for internal AP and router.

SIP TLS/sRTP on Cisco border router (CUBE)

Similar Messages

Maybe you are looking for