Site survey for location based services

Hi Experts ,
Wht are the paramenters I need to concentrate while doing the site survey that incldes the requirement of location services?
Thanks,
Regards,
Vijay.

Location-based services:
WLAN location-based services requires that access points are placed in such a
fashion that the Active RFID tags and 802.11 clients ar
e surrounded by access points for ultimate optimization.
(This is a different access point placement strategy than data and voice WLAN only networks). If you are
surveying for location based services, acce
ss point placement is done differently. For more information on
deploying location based services, refer to the Cisco 2700 Series Wireless Location Appliance Deployment
Guide available at Cisco.com.
http://www.cisco.com/en/US/docs/wireless/technology/vowlan/troubleshooting/8_Site_Survey_RF_Design_Valid.html

Similar Messages

  • Does location based services (LBS) work for international locations (outside the USA)?

    Does location based services (LBS) work for international locations (outside the USA)? For example does it work in Canada, European countries etc. Any help is appreciated.

    Yes, but possibly limited to coverage of Skyhook database..
    Applications that use location services also use the data from Skyhook...
    Skyhook is a service that records the MAC addresses of Cell Base stations/towers and wireless access points.
    Google Maps vehicles records the wireless AP data at the same time they get street view images.
    There was some controversy over this - but they effectively record the location and the MAC address of any AP they find as they drive round. This gets sent to a massive database at Skyhook and is used to either locate without GPS or enhance/aid the GPS information. It's also why the location is always the road outside!
    If your location/MAC relationship has not been mapped by Skyhook, Google or others - then the good news is that you can add it - although it can take a month or two at least - to work. The reason is that it depends which database is being used by Skyhook's clients..
    Add your Wireless Access Point (or Wireless Router) here: http://www.skyhookwireless.com/howitworks/submit_ap.php
    The main website for Skyhook is here: http://www.skyhookwireless.com
    Hope that helps...!

  • Location based services with ELM AP?

    Hello Experts,
    Maybe you have some experience with this stuff? Is it possible to use location based services with Enhanced Local Mode APs?

    As long as the AP is serving clients it can, once you remove that and set it like in Monitor Mode and use it for a sniffer or spectrum it can't. So as long as your site survey has triangulation and meets the requirement for location base, you should be fine.
    Sent from Cisco Technical Support iPhone App

  • Wireless Site-Survey for High Density Environment

    Hi,
    I have done many Wireless SIte-Surveys in my career. But this will the first time, I am going to do a Site-Survey for High Density environment (School with Byod 1:1 design).
    Currently, the school has a Wireless network in place. The current wireless design includes 3502 APs, 5508 WLC and Cisco Prime. The customer has issues with sufficient bandwidth in classrooms which limiting the students and teachers to access the learning content.
    It is understood that there was no initial Site-Survey conducted, the AP positioning was made based on their knowledge.
    Now, I am not sure as how to conduct the Survey here?
    Do I need to conduct an Active Survey by connecting to the existing Wireless Network in the School? Or just passive Survey will be enough to determine the exact issues with the current design and provide the recommendations?
    I have gone through the Cisco High Density design and white papers to start with.
    Thanks,
    CJ

    Before you do the site survey, I'd do the initial breakdown of the LAN.
    1.  What kind of switch ports are we talking about?
    2.  Are the APs connected AND negotiated to 1 Gbps ports?
    3.  What is/are the switch uplinks?  100 Mbps, 1- or 10- Gbps, Etherchannel?
    4.  Line errors on the links between the AP and the switch, uplinks and the link between the WLC and the switches?
    5.  WLC link?  How many are used?  Are they LAG or not?
    6.  Configuration of the WLC must be checked.
    Once you've checked these do I start talking about wireless:
    1.  What problems are the staff/students experiencing?
    2.  How many APs to a classroom?  How big is the class?
    3.  Determine what kind of traffic are each class trying to push?
    4.  Where are the APs located in relations to the staff/student?
    5.  Verify co-channel interferrence.  I know they have 3502 but I've seen people disable CleanAir.
    6.  Verify what kind of NIC cards are used and whether drivers have been updated or not.
    I'm in the middle of improving our wireless coverage in >98 schools.  This means I am now deploying 1 AP per classroom.  In areas where the students/staff converge, I put additional APs (both indoors and outdoors).

  • "Adding Location Based Services to Your Application" help me

    Hi all
    In the OBE tutorial " Adding Location Based Services to Your Application" has:
    "Enter Wireless for Library Name. Set the classpath to include the wireless.jar from your installation. For example, C:\midtier_pw\wireless\lib\wireless.jar. Click OK.
    The new library should now appear in your Selected Libraries list. Click OK to close the Properties window. "
    But i don't know where the Wireless.jar file is. Please tell me
    thanks
    [email protected]

    help me to perform adding WEB Services as described bellow:
    Hello,
    It depends a Little bit on the used Visual Studio Version. Basically do a right-mouse click on "References" and select
    The next steps are a Little bit hidden & confusing: In the next Dialog click on "Advanced..", then add "Web reference" and here you can enter the URL for SSRS SOAP, click on the green arrow and the WSDL data will be retrieved &
    shown in the Dialog:
    Olaf Helper
    [ Blog] [ Xing] [ MVP]

  • How to configure proxy services in OSB for Rest based services?

    how to configure proxy services in OSB for Rest based services implemented using Jersey (Rest).
    The Client need to contact OSB proxy servies by posting application/xml using jersey client and OSB proxy service will call the OSB business service.
    i would like to know how to get this request in OSB proxy service and send it to the business service and get the response back.

    I would suggest you refer to the below links:
    https://blogs.oracle.com/jeffdavies/entry/restful_services_with_oracle_s_1
    https://blogs.oracle.com/jamesbayer/entry/using_rest_with_oracle_service
    Hope this helps.
    Thanks,
    Patrick

  • Best practice power setting when doing a Site Survey for VOIP

    Hi Team,
    Can someone please confirm or correct me.  When doing a Wireless Active Site Survey for Cisco VOIP, I should be setting the Test AP to local power of 14, which is 25mW?  Is this correct, or should it be another value?  I asked the customer for the power of their weakest client and they do not know, but they claim there's a high probably that they will go with Cisco VOIP clients.
    Thanks...

    When you check the signal coverage, make sure the AP's radio transmit power does not use a transmit power greater than what the client devices can support. For example, by default, the Cisco Unified Wireless IP Phone 7925G uses the highest available transmit power by default (17 dBm / 50 mW for 2.4 GHz and 16 dBm / 40 mW for 5 GHz). It is possible to have a survey report that shows good coverage in all areas; however, if you have APs that operate at the highest transmit power, you might still experience uplink issues where the client devices do not support the same transmit power. For areas where there is deficient coverage, and you increase the AP transmit power to levels that the client devices cannot support, this only increases coverage on the downlink.
    Link for the same :-
    http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey-guidelines-wlan-00.html

  • Can I create JDE BSSV (Business Services) for REST based services?

    Can I create JDE BSSV (Business Services) for REST based services? If yes, then how? In what way it will be different from SOAP based?

    Hi
    Within Oracle SOA Suite, Oracle Service Bus would handle the REST side of things, which in turn would call the JCA adapter to talk to your JDE backend, or vice versa.
    Checkout the JDE adapter docs - http://www.oracle.com/technetwork/middleware/soasuite/documentation/jdewardsweb-1954164.pdf
    and the OSB Docs - HTTP and Poller Transports - 11g Release 1 (11.1.1.7)
    OSB 11.1.1.7 introduced additional REST support, so I'd recommend using that version onwards.
    Cheers
    iain

  • Site survey for 3502i access point

    Hi,
    I want to do initial site survey to fix the location of 3502i but there is no existing lan-set up where i can connect and do the site survey.
    I do not have autonomous ap as well.
    do i need to wait to get ethernet lan up and connect my ap and get registered ap with WLC and then fix the location or is there any other way to do site survey?
    Please suggest me .

    There is now available beta code for autonomous 1260 series APs.  You could reach out to your Cisco contact and try to get that.  The 1260 and 3500 series APs are identical with the exception of the spectrum capabilities in the 3500.  So you can survey for a 3500 deployment with an autonomous 1260.
    Regards,
    Scott

  • Specifying tcpd for inetd based service in creating manifest

    If I use an old inetd based service that specified /usr/sbin/tcpd, do I have to include that when I use inetconv to create the service manifest.
    For example.
    I currently use proftpd for ftp with tcp_wrappers. My old inetd line was
    ftp stream tcp nowait root /usr/sbin/tcpd /usr/local/sbin/in.proftpd.
    If I want to create a manifest for this, do I include /usr/sbin/tcpd in the line as it was before?
    Thank you

    Hi Bharathwaj.
    Did you solve this issue? The string index out of range problem can be solved by setting Use_CustomerExit_ParameterProvider to true for the AppIntegrator service, the procedure is described in the latest version of the Self-Service Administrator documentation.
    What about the other issue? Were you able to make the application views visible for the Web Dynpro component so that iViews can be created for them? I have setup FPM Applications and FPM Views but I fail to see how to establish the link between the iView, Web Dynpro component and the FPM Application.
    I even attempted to make the Web Dynpro application use Multiple iViews as documented in the SAP Help Portal, that didn't do it.
    Thanks for any tips,
    Samuli

  • Location Based Services . How to?

    Can anyone recommend a good third party software that would provide LBS for an app I need to write? I need to find some way of getting the position of a user on a mobile device either on the host or client side. So far from looking I havent seen an API or any software that a developer can integrate with to get this functionality.
    Thanks!!

    Hi,
    The location based api proposed jsr is JSR-179. You can find the details at http://jcp.org/en/jsr/detail?id=179
    Hope this will help you.
    There is no reference implementation available as yet.
    thanks,
    Digvijay

  • Site survey for voip cutover

    need a template to conduct a site survey to determine phone lines, extentions, phone features, etc

    The following book has some useful questionnaires.
    http://www.ciscopress.com/bookstore/product.asp?isbn=1587051575
    Hope this helps. If so, please rate the post.
    Brandon

  • Location Based Services

    Hi all!
    Does anyone know if there is any mobile device which currently supposts "JSR-179" which is the API for physically locating a mobile phone or device???
    Thanks...

    Hi
    I couldn't add the location API to my J2ME Wireless Toolkit 2.2 but installing the new version of that J2ME Wireless Toolkit (2.3) I was able to get the Location Base API 1.0 which is included in that kit and work fine in an emulator. The version 2.3 is a beta release and can be downloaded from sun site. I don't know if there is a final release, if so, let me know.
    I hope this help.
    Amilkar

  • Location based services algorithm

    hi all,
    does anyone know the algorithm(s) used to locate an address or something else, in websites like mappy.com. I need this algorithm to do a syntactic research (java implementation).
    thanks a lot,

    Attention would-be duplicate answers: This is probably a continuation of this topic:
    http://forum.java.sun.com/thread.jspa?threadID=616293

  • Cisco 3502i in autonomous mode - for site survey

    Hi,
    Last year I was able to load autonomous mode IOS to a cisco 3502i to do the site survey using instructions at following thread.
    https://supportforums.cisco.com/thread/2084624
    This year I have to do site survey for a different site and need to do the same process. However on the CCO I don't see the autonomous image. Under downloads -> products -> wireless -> access points -> Cisco 3502i I see IOS link and when clicked there is gives
    ap3g1-k9w8-tar.124-23c.JA4.tar. I even loaded that IOS but it seems to be light weight mode IOS.
    After reading a few different threads somebody clarified that K7 = IOS and K8 = Lightweight. However I can't seem to find the lightweight mode anywhere.
    https://supportforums.cisco.com/thread/2140629
    Can somebody guide me? I need to run this code only for the site survey and totally understand the fact that Cisco would not support such configuration.
    Thanks in advance,

    Sorry to inform you but there is no autonomous code for the 3500. You could however use the 1140 code. But this not supported by Cisco but it does work ..
    Sent from Cisco Technical Support iPhone App

Maybe you are looking for