Site to Site tunnel: ESP request discarded
Hello. I've got a site to site tunnel configured in an ASA-5540 (8.3) and at first working fine. After several hours, the tunnel is disconnected and I this log appear without stopping:
%ASA-7-710006: ESP request discarded from "tunnel IP peer" to outside_int:"my tunnel IP"
I can't figure out why the tunnel stop working and the meaning of this message. The explanation in Cisco documents does't fix to me.
Thanks.
Hi,
At HQ ASA atleast the NAT0 configuration is wrong
You have configured this
nat (inside) 5 access-list inside_nat0_outbound
This isnt NAT0 however. It would be configured with ID 5 if you had a corresponding "global" commands using ID 5 also. It would be a Dynamic Policy NAT/PAT.
The NAT0 configurations should use the ID 0
If an existing NAT0 "nat" statement/configuration already exists then you would use the existing ACL to define the traffic that doesnt need NAT
So your configuration should probably be this
nat (inside) 0 access-list inside_nat0_outbound
I can't see a different in the actual L2L VPN configurations though there are some configurations that are not visible that might affect connectivity BUT the above mentioned NAT0 configurations is clearly a problem.
Hope this helps
Please remember to mark a reply as the correct answer if it answered your question.
Feel free to ask more if needed
- Jouni
Similar Messages
-
ASA ESP Packet discard messages
Dear All,
we have a L2L tunnel between ASA 8.2.5 to Cisco Router. Recently we see tunnel is going down and shows messages in ASA about ESP packet discard. Below is the message.
%ASA-7-710006: ESP request discarded from x.x.x.x to outside_int:x.x.x
At the same time from router the tunnel shows up but ASA not. We see CSCso50226 which matches exactly with our issue.
As a workaround we were resetting tunnel from router. It comes up and runs for a week.
Please someone look into this and help.
Regards,
RaviHi Ravi,
8.4 is great, dont let the NAT change scare you off two much and 8.2 was really buggy.
I guess this raises further questions, if your tunnel goes down once a week is it the same length of time ? and does this relate to the timings set on either end in teh configuration ?
When the tunnel goes down is it at a quiet time ? and have you tried using a test ping/rtr/sla to keep the tunnel up ?
The site below identifies the syslog messages and yours makes me think somethings not right. Do you have the sysoptions enabled or are you using ACL's to limit who can connect to the appliance as a vpn peer ? If you have ACL's have you included IP 50 ?
http://www.cisco.com/en/US/docs/security/asa/asa82/system/message/logmsgs.html
710006
Error Message %ASA-7-710006: protocol request discarded from source_address to
interface_name:dest_address
Explanation This message appears when the adaptive security appliance does not have an IP server that services the IP protocol request; for example, the adaptive security appliance receives IP packets that are not TCP or UDP, and the adaptive security appliance cannot service the request.
Recommended Action In networks that use broadcasting services such as DHCP, RIP or NetBIOS extensively, the frequency of this message can be high. If this message appears in excessive numbers, it may indicate an attack.
Best Regards
Ju
http://helpamunky.wordpress.com/ -
%ASA-7-710005: TCP request discarded error in Client to Site VPN in CISCO ASA 5510
Hi Friends,
I'm trying to built client to site VPN in CISCO ASA 5510 8.4(4) and getting below error while connecting cisco VPN client software. Also, I'm getting below log in ASA. Please help me to reslove.
Error in CISCO VPN Client Software:
Secure VPN Connection Terminated locally by the client.
Reason : 414 : Failed to establish a TCP connection.
Error in CISCO ASA 5510
%ASA-7-710005: TCP request discarded from <Public IP> /49276 to outside:<Outside Interface IP of my ASA> /10000
ASA Configuration:
XYZ# sh run
: Saved
ASA Version 8.4(4)
hostname XYZ
domain-name XYZ
enable password 3uLkVc9JwRA1/OXb level 3 encrypted
enable password R/x90UjisGVJVlh2 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
nameif outside_rim
security-level 0
ip address 1.1.1.1 255.255.255.252
interface Ethernet0/1
duplex full
nameif XYZ_DMZ
security-level 50
ip address 172.1.1.1 255.255.255.248
interface Ethernet0/2
speed 100
duplex full
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.252
interface Ethernet0/3
speed 100
duplex full
nameif inside
security-level 100
ip address 3.3.3.3 255.255.255.224
interface Management0/0
shutdown
no nameif
no security-level
no ip address
boot system disk0:/asa844-k8.bin
ftp mode passive
dns domain-lookup outside
dns server-group DefaultDNS
name-server xx.xx.xx.xx
name-server xx.xx.xx.xx
name-server xx.xx.xx.xx
name-server xx.xx.xx.xx
domain-name XYZ
object network obj-172.17.10.3
host 172.17.10.3
object network obj-10.1.134.0
subnet 10.1.134.0 255.255.255.0
object network obj-208.75.237.0
subnet 208.75.237.0 255.255.255.0
object network obj-10.7.0.0
subnet 10.7.0.0 255.255.0.0
object network obj-172.17.2.0
subnet 172.17.2.0 255.255.255.0
object network obj-172.17.3.0
subnet 172.17.3.0 255.255.255.0
object network obj-172.19.2.0
subnet 172.19.2.0 255.255.255.0
object network obj-172.19.3.0
subnet 172.19.3.0 255.255.255.0
object network obj-172.19.7.0
subnet 172.19.7.0 255.255.255.0
object network obj-10.1.0.0
subnet 10.1.0.0 255.255.0.0
object network obj-10.2.0.0
subnet 10.2.0.0 255.255.0.0
object network obj-10.3.0.0
subnet 10.3.0.0 255.255.0.0
object network obj-10.4.0.0
subnet 10.4.0.0 255.255.0.0
object network obj-10.6.0.0
subnet 10.6.0.0 255.255.0.0
object network obj-10.9.0.0
subnet 10.9.0.0 255.255.0.0
object network obj-10.11.0.0
subnet 10.11.0.0 255.255.0.0
object network obj-10.12.0.0
subnet 10.12.0.0 255.255.0.0
object network obj-172.19.1.0
subnet 172.19.1.0 255.255.255.0
object network obj-172.21.2.0
subnet 172.21.2.0 255.255.255.0
object network obj-172.16.2.0
subnet 172.16.2.0 255.255.255.0
object network obj-10.19.130.201
host 10.19.130.201
object network obj-172.30.2.0
subnet 172.30.2.0 255.255.255.0
object network obj-172.30.3.0
subnet 172.30.3.0 255.255.255.0
object network obj-172.30.7.0
subnet 172.30.7.0 255.255.255.0
object network obj-10.10.1.0
subnet 10.10.1.0 255.255.255.0
object network obj-10.19.130.0
subnet 10.19.130.0 255.255.255.0
object network obj-XXXXXXXX
host XXXXXXXX
object network obj-145.248.194.0
subnet 145.248.194.0 255.255.255.0
object network obj-10.1.134.100
host 10.1.134.100
object network obj-10.9.124.100
host 10.9.124.100
object network obj-10.1.134.101
host 10.1.134.101
object network obj-10.9.124.101
host 10.9.124.101
object network obj-10.1.134.102
host 10.1.134.102
object network obj-10.9.124.102
host 10.9.124.102
object network obj-115.111.99.133
host 115.111.99.133
object network obj-10.8.108.0
subnet 10.8.108.0 255.255.255.0
object network obj-115.111.99.129
host 115.111.99.129
object network obj-195.254.159.133
host 195.254.159.133
object network obj-195.254.158.136
host 195.254.158.136
object network obj-209.164.192.0
subnet 209.164.192.0 255.255.224.0
object network obj-209.164.208.19
host 209.164.208.19
object network obj-209.164.192.126
host 209.164.192.126
object network obj-10.8.100.128
subnet 10.8.100.128 255.255.255.128
object network obj-115.111.99.130
host 115.111.99.130
object network obj-10.10.0.0
subnet 10.10.0.0 255.255.0.0
object network obj-115.111.99.132
host 115.111.99.132
object network obj-10.10.1.45
host 10.10.1.45
object network obj-10.99.132.0
subnet 10.99.132.0 255.255.255.0
object-group network Serversubnet
network-object 10.10.1.0 255.255.255.0
network-object 10.10.5.0 255.255.255.192
object-group network XYZ_destinations
network-object 10.1.0.0 255.255.0.0
network-object 10.2.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 10.11.0.0 255.255.0.0
network-object 10.12.0.0 255.255.0.0
network-object 172.19.1.0 255.255.255.0
network-object 172.19.2.0 255.255.255.0
network-object 172.19.3.0 255.255.255.0
network-object 172.19.7.0 255.255.255.0
network-object 172.17.2.0 255.255.255.0
network-object 172.17.3.0 255.255.255.0
network-object 172.16.2.0 255.255.255.0
network-object 172.16.3.0 255.255.255.0
network-object host 10.50.2.206
object-group network XYZ_us_admin
network-object 10.3.1.245 255.255.255.255
network-object 10.5.33.7 255.255.255.255
network-object 10.211.5.7 255.255.255.255
network-object 10.3.33.7 255.255.255.255
network-object 10.211.3.7 255.255.255.255
object-group network XYZ_blr_networkdevices
network-object 10.200.10.0 255.255.255.0
access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host 172.16.2.21
access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host 172.16.2.22
access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host XXXXXXXX
access-list XYZ_PAT extended permit ip 10.19.130.0 255.255.255.0 any
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 195.254.159.133
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 195.254.158.136
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 any
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 209.164.192.0 255.255.224.0
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 209.164.208.19
access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 209.164.192.126
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.7.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.17.2.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.17.3.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.2.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.3.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.7.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.1.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.2.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.3.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.4.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.6.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.9.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.11.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.12.0.0 255.255.0.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.1.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.21.2.0 255.255.255.0
access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.16.2.0 255.255.255.0
access-list nonat extended permit ip host 10.19.130.201 172.30.2.0 255.255.255.0
access-list nonat extended permit ip host 10.19.130.201 172.30.3.0 255.255.255.0
access-list nonat extended permit ip host 10.19.130.201 172.30.7.0 255.255.255.0
access-list nonat extended permit ip object-group Serversubnet object-group XYZ_destinations
access-list nonat extended permit ip 10.10.1.0 255.255.255.0 10.2.0.0 255.255.0.0
access-list nonat extended permit ip 10.19.130.0 255.255.255.0 host XXXXXXXX
access-list nonat extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
access-list Guest_PAT extended permit ip 10.8.108.0 255.255.255.0 any
access-list Cacib extended permit ip 10.8.100.128 255.255.255.128 145.248.194.0 255.255.255.0
access-list Cacib_PAT extended permit ip 10.8.100.128 255.255.255.128 any
access-list New_Edge extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
access-list XYZ_global extended permit ip 10.7.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.7.0.0 255.255.0.0
access-list XYZ_global extended permit ip 172.17.2.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.17.3.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.19.2.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.19.3.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.19.7.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.2.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.3.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.4.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.6.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.9.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.11.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.12.0.0 255.255.0.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.19.1.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 172.21.2.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.17.2.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.17.3.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.2.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.3.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.7.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.1.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.2.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.3.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.4.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.6.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.9.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.11.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.12.0.0 255.255.0.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.1.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.21.2.0 255.255.255.0
access-list XYZ_global extended permit ip 172.16.2.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.16.2.0 255.255.255.0
access-list XYZ_global extended permit ip 172.30.2.0 255.255.255.0 host 10.19.130.201
access-list XYZ_global extended permit ip host 10.19.130.201 172.30.2.0 255.255.255.0
access-list XYZ_global extended permit ip 172.30.3.0 255.255.255.0 host 10.19.130.201
access-list XYZ_global extended permit ip host 10.19.130.201 172.30.3.0 255.255.255.0
access-list XYZ_global extended permit ip 172.30.7.0 255.255.255.0 host 10.19.130.201
access-list XYZ_global extended permit ip host 10.19.130.201 172.30.7.0 255.255.255.0
access-list XYZ_global extended permit ip object-group Serversubnet object-group XYZ_destinations
access-list XYZ_global extended permit ip object-group XYZ_destinations object-group Serversubnet
access-list ML_VPN extended permit ip host 115.111.99.129 209.164.192.0 255.255.224.0
access-list ML_VPN extended permit ip host 115.111.99.129 host 209.164.208.19
access-list ML_VPN extended permit ip host 115.111.99.129 host 209.164.192.126
access-list Da_VPN extended permit ip host 10.9.124.100 host 10.125.81.88
access-list Da_VPN extended permit ip host 10.9.124.101 host 10.125.81.88
access-list Da_VPN extended permit ip host 10.9.124.102 host 10.125.81.88
access-list Da_VPN extended permit ip host 10.9.124.100 10.125.81.0 255.255.255.0
access-list Da_VPN extended permit ip host 10.9.124.101 10.125.81.0 255.255.255.0
access-list Da_VPN extended permit ip host 10.9.124.102 10.125.81.0 255.255.255.0
access-list Sr_PAT extended permit ip 10.10.0.0 255.255.0.0 any
access-list Da_Pd_VPN extended permit ip host 10.9.124.100 10.125.80.64 255.255.255.192
access-list Da_Pd_VPN extended permit ip host 10.9.124.100 10.125.64.0 255.255.240.0
access-list Da_Pd_VPN extended permit ip host 10.9.124.100 host 10.125.85.46
access-list Da_Pd_VPN extended permit ip host 10.9.124.100 host 10.125.86.46
access-list Da_Pd_VPN extended permit ip host 10.9.124.101 10.125.80.64 255.255.255.192
access-list Da_Pd_VPN extended permit ip host 10.9.124.101 10.125.64.0 255.255.240.0
access-list Da_Pd_VPN extended permit ip host 10.9.124.101 host 10.125.85.46
access-list Da_Pd_VPN extended permit ip host 10.9.124.101 host 10.125.86.46
access-list Da_Pd_VPN extended permit ip host 10.9.124.102 10.125.80.64 255.255.255.192
access-list Da_Pd_VPN extended permit ip host 10.9.124.102 10.125.64.0 255.255.240.0
access-list Da_Pd_VPN extended permit ip host 10.9.124.102 host 10.125.85.46
access-list Da_Pd_VPN extended permit ip host 10.9.124.102 host 10.125.86.46
access-list XYZ_reliance extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
access-list coextended permit ip host 2.2.2.2 host XXXXXXXX
access-list coextended permit ip host XXXXXXXXhost 2.2.2.2
access-list ci extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
access-list ci extended permit ip 208.75.237.0 255.255.255.0 10.1.134.0 255.255.255.0
access-list acl-outside extended permit ip host 57.66.81.159 host 172.17.10.3
access-list acl-outside extended permit ip host 80.169.223.179 host 172.17.10.3
access-list acl-outside extended permit ip any host 172.17.10.3
access-list acl-outside extended permit tcp any host 10.10.1.45 eq https
access-list acl-outside extended permit tcp any any eq 10000
access-list acl-outside extended deny ip any any log
pager lines 10
logging enable
logging buffered debugging
mtu outside_rim 1500
mtu XYZ_DMZ 1500
mtu outside 1500
mtu inside 1500
ip local pool XYZ_c2s_vpn_pool 172.30.10.51-172.30.10.254
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
no asdm history enable
arp timeout 14400
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-208.75.237.0 obj-208.75.237.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.7.0.0 obj-10.7.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.17.2.0 obj-172.17.2.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.17.3.0 obj-172.17.3.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.2.0 obj-172.19.2.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.3.0 obj-172.19.3.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.7.0 obj-172.19.7.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.1.0.0 obj-10.1.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.2.0.0 obj-10.2.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.3.0.0 obj-10.3.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.4.0.0 obj-10.4.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.6.0.0 obj-10.6.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.9.0.0 obj-10.9.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.11.0.0 obj-10.11.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.12.0.0 obj-10.12.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.1.0 obj-172.19.1.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.21.2.0 obj-172.21.2.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.16.2.0 obj-172.16.2.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.2.0 obj-172.30.2.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.3.0 obj-172.30.3.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.7.0 obj-172.30.7.0 no-proxy-arp route-lookup
nat (inside,any) source static Serversubnet Serversubnet destination static XYZ_destinations XYZ_destinations no-proxy-arp route-lookup
nat (inside,any) source static obj-10.10.1.0 obj-10.10.1.0 destination static obj-10.2.0.0 obj-10.2.0.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-10.19.130.0 obj-10.19.130.0 destination static obj-XXXXXXXX obj-XXXXXXXX no-proxy-arp route-lookup
nat (inside,any) source static obj-10.19.130.0 obj-10.19.130.0 destination static obj-145.248.194.0 obj-145.248.194.0 no-proxy-arp route-lookup
nat (inside,outside) source static obj-10.1.134.100 obj-10.9.124.100
nat (inside,outside) source static obj-10.1.134.101 obj-10.9.124.101
nat (inside,outside) source static obj-10.1.134.102 obj-10.9.124.102
nat (inside,outside) source dynamic obj-10.8.108.0 interface
nat (inside,outside) source dynamic obj-10.19.130.0 obj-115.111.99.129
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-195.254.159.133 obj-195.254.159.133
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-195.254.158.136 obj-195.254.158.136
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.192.0 obj-209.164.192.0
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.208.19 obj-209.164.208.19
nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.192.126 obj-209.164.192.126
nat (inside,outside) source dynamic obj-10.8.100.128 obj-115.111.99.130
nat (inside,outside) source dynamic obj-10.10.0.0 obj-115.111.99.132
nat (inside,outside) source static obj-10.10.1.45 obj-115.111.99.133
nat (inside,outside) source dynamic obj-10.99.132.0 obj-115.111.99.129
object network obj-172.17.10.3
nat (XYZ_DMZ,outside) static 115.111.99.134
access-group acl-outside in interface outside
route outside 0.0.0.0 0.0.0.0 115.111.23.129 1
route outside 0.0.0.0 0.0.0.0 115.254.127.130 10
route inside 10.10.0.0 255.255.0.0 10.8.100.1 1
route inside 10.10.1.0 255.255.255.0 10.8.100.1 1
route inside 10.10.5.0 255.255.255.192 10.8.100.1 1
route inside 10.8.100.128 255.255.255.128 10.8.100.1 1
route inside 10.8.108.0 255.255.255.0 10.8.100.1 1
route inside 10.19.130.0 255.255.255.0 10.8.100.1 1
route inside 10.99.4.0 255.255.255.0 10.99.130.254 1
route inside 10.99.132.0 255.255.255.0 10.8.100.1 1
route inside 10.1.134.0 255.255.255.0 10.8.100.1 1
route outside 208.75.237.0 255.255.255.0 115.111.23.129 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set vpn2 esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set vpn6 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set vpn5 esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set vpn7 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set vpn4 esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set vpn1 esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set vpn_reliance esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set c2s_vpn esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 86400
crypto dynamic-map dyn1 1 set ikev1 transform-set c2s_vpn
crypto dynamic-map dyn1 1 set reverse-route
crypto map vpn 1 match address XYZ
crypto map vpn 1 set peer XYZ Peer IP
crypto map vpn 1 set ikev1 transform-set vpn1
crypto map vpn 1 set security-association lifetime seconds 3600
crypto map vpn 1 set security-association lifetime kilobytes 4608000
crypto map vpn 2 match address NE
crypto map vpn 2 set peer NE_Peer IP
crypto map vpn 2 set ikev1 transform-set vpn2
crypto map vpn 2 set security-association lifetime seconds 3600
crypto map vpn 2 set security-association lifetime kilobytes 4608000
crypto map vpn 4 match address ML_VPN
crypto map vpn 4 set pfs
crypto map vpn 4 set peer ML_Peer IP
crypto map vpn 4 set ikev1 transform-set vpn4
crypto map vpn 4 set security-association lifetime seconds 3600
crypto map vpn 4 set security-association lifetime kilobytes 4608000
crypto map vpn 5 match address XYZ_global
crypto map vpn 5 set peer XYZ_globa_Peer IP
crypto map vpn 5 set ikev1 transform-set vpn5
crypto map vpn 5 set security-association lifetime seconds 3600
crypto map vpn 5 set security-association lifetime kilobytes 4608000
crypto map vpn 6 match address Da_VPN
crypto map vpn 6 set peer Da_VPN_Peer IP
crypto map vpn 6 set ikev1 transform-set vpn6
crypto map vpn 6 set security-association lifetime seconds 3600
crypto map vpn 6 set security-association lifetime kilobytes 4608000
crypto map vpn 7 match address Da_Pd_VPN
crypto map vpn 7 set peer Da_Pd_VPN_Peer IP
crypto map vpn 7 set ikev1 transform-set vpn6
crypto map vpn 7 set security-association lifetime seconds 3600
crypto map vpn 7 set security-association lifetime kilobytes 4608000
crypto map vpn interface outside
crypto map vpn_reliance 1 match address XYZ_rim
crypto map vpn_reliance 1 set peer XYZ_rim_Peer IP
crypto map vpn_reliance 1 set ikev1 transform-set vpn_reliance
crypto map vpn_reliance 1 set security-association lifetime seconds 3600
crypto map vpn_reliance 1 set security-association lifetime kilobytes 4608000
crypto map vpn_reliance interface outside_rim
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto isakmp identity address
no crypto isakmp nat-traversal
crypto ikev1 enable outside_rim
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 28800
crypto ikev1 policy 2
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
crypto ikev1 policy 4
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 28000
crypto ikev1 policy 5
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.8.100.0 255.255.255.224 inside
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
no threat-detection basic-threat
no threat-detection statistics access-list
no threat-detection statistics tcp-intercept
group-policy XYZ_c2s_vpn internal
username testadmin password oFJjANE3QKoA206w encrypted
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXXtype ipsec-l2l
tunnel-group XXXXXXXXipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group XXXXXXXX ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group XYZ_c2s_vpn type remote-access
tunnel-group XYZ_c2s_vpn general-attributes
address-pool XYZ_c2s_vpn_pool
tunnel-group XYZ_c2s_vpn ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
inspect ip-options
service-policy global_policy global
privilege show level 3 mode exec command running-config
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command crypto
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:caa7476cd348ed89b95d37d4e3c9e1d8
: end
XYZ#Thanks Javier.
But i have revised the VPN confuration. Below are the latest configs. with this latest configs. I'm getting username & password screen while connecting cisco vpn client software. once we entered the login credential. it shows "security communication channel" then it goes to "not connected" state. Can you help me to fix this.
access-list ACL-RA-SPLIT standard permit host 10.10.1.3
access-list ACL-RA-SPLIT standard permit host 10.10.1.13
access-list ACL-RA-SPLIT standard permit host 10.91.130.201
access-list nonat line 1 extended permit ip host 10.10.1.3 172.30.10.0 255.255.255.0
access-list nonat line 2 extended permit ip host 10.10.1.13 172.30.10.0 255.255.255.0
access-list nonat line 3 extended permit ip host 10.91.130.201 172.30.10.0 255.255.255.0
ip local pool CO-C2S-VPOOL 172.30.10.51-172.30.10.254 mask 255.255.255.0
group-policy CO-C2S internal
group-policy CO-C2S attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list vlauel ACL-RA-SPLIT
dns-server value 10.10.1.3
tunnel-group TUN-RA-SPLIT type remote-access
tunnel-group TUN-RA-SPLIT general-attributes
default-group-policy CO-C2S
address-pool CO-C2S-VPOOL
tunnel-group TUN-RA-SPLIT ipsec-attributes
pre-shared-key sekretk3y
username ra-user1 password passw0rd1 priv 1
group-policy CO-C2S internal
group-policy CO-C2S attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list vlauel ACL-RA-SPLIT
dns-server value 10.10.1.3
tunnel-group TUN-RA-SPLIT type remote-access
tunnel-group TUN-RA-SPLIT general-attributes
default-group-policy CO-C2S
address-pool CO-C2S-VPOOL
tunnel-group TUN-RA-SPLIT ipsec-attributes
pre-shared-key *********
username ******* password ******** priv 1
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10 set transform-set 3DES
crypto map Outside_Map 500 ipsec-isakmp dynamic dynmap
crypto isakmp identify address
crypto isakmp enable outside
crypto isakmp policy 100
authentication pre-share
encr 3des
hash sha
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10 set transform-set 3DES
crypto map Outside_Map 500 ipsec-isakmp dynamic dynmap
crypto map vpn interface outside
crypto isakmp identify address
crypto isakmp enable outside
crypto isakmp policy 100
authentication pre-share
encr 3des
hash sha
group 1
lifetime 3600 -
CISCO ASA 5505 Split Tunnel DNS with Site to Site VPN
I have a working configuration for Site to Site VPN between our head office and a private AWS VPC instance.
The tunnel is active and I can ping the IP address of the remote network and connect to the remote machines using the IP address, but we need to use the FQDN and not the IP. We have a DNS server set up in AWS for any DNS queries for the remote domain name.
My question is whether or not the ASA 5505 supports a DNS split tunnel for Site to Site VPN and how it can be configured.
I can not find where I can interogate the DNS query to be redirected to the VPN tunnel when our domain name is used in a DNS query. Thus, any pings I try with the FQDN of our servers in AWS are failing as they are going to the default DNS, which is the internet.
Can any one point me in the right direction on how to configure this DNS rewrite so that we can access our AWS private cloud using FQDN from our AWS domain rather than an IP address?Jose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ? -
Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall
Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 195.149.180.254
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
current_peer:195.149.180.254
#pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
#pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: E715B315
inbound esp sas:
spi: 0xFAC769EB (4207372779)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38738/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xE715B315 (3876958997)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38673/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
MichaelHi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni -
Configure a VPN client and Site to Site VPN tunnel
Hi, I'm setting up a test network between 2 sites. SiteA has a 515E PIX and SiteB has a 501 PIX. Both sites have been setup with a site to site VPN tunnel, see SiteA config below. I also require that remote clients using Cisco VPN client 3.6 be able to connect into SiteA, be authenticated, get DHCP info and connect to hosts inside the network. However, when I add these config lines, see below, to SiteA PIX it stops the vpn tunnel to SiteB. However, the client can conect and do as needed so that part of my config is correct but I cannot see why the site to site vpn tunnel is then no longer.
SiteA config with working VPN tunnel to SiteB:
SITE A
PIX Version 6.3(1)
interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 auto shutdown
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 webdmz security20
enable password xxx
passwd xxx
hostname SiteA-pix
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol rsh 514
fixup protocol rtsp 554
no fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
names
name 200.x.x.0 SiteA_INT
name 201.x.x.201 SiteA_EXT
name 200.x.x.254 PIX_INT
name 10.10.10.0 SiteB_INT
name 11.x.x.11 SiteB_EXT
access-list inside_outbound_nat0_acl permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
access-list outside_cryptomap_20 permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
access-list acl_inside permit icmp any any
access-list acl_inside permit ip any any
access-list acl_outside permit ip any any
access-list acl_outside permit icmp any any
pager lines 24
mtu outside 1500
mtu inside 1500
mtu webdmz 1500
ip address outside SiteA_EXT 255.x.x.128
ip address inside PIX_INT 255.255.0.0
no ip address webdmz
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
route outside 0.0.0.x.x.0.0 201.201.201.202 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto map outside_map 20 ipsec-isakmp
crypto map outside_map 20 match address outside_cryptomap_20
crypto map outside_map 20 set peer SiteB_EXT
crypto map outside_map 20 set transform-set ESP-DES-MD5
crypto map outside_map interface outside
isakmp enable outside
isakmp key secret address SiteB_EXT netmask 255.255.255.255 no-xauth no-config-mode
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
SiteA-pix(config)#
Lines I add for Cisco VPN clients is attached
I entered each line one by one and did a reload and sh crypto map all was OK until I entered the crypto map VPNPEER lines.
Anyone any ideas what this can be?
ThanksHeres my config:
PIX Version 6.3(1)
interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 auto shutdown
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 webdmz security20
enable password xxx
passwd xxx
hostname SiteA-pix
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol rsh 514
fixup protocol rtsp 554
no fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
names
name 200.x.x.0 SiteA_INT
name 201.x.x.201 SiteA_EXT
name 200.x.x.254 PIX_INT
name 10.10.10.0 SiteB_INT
name 11.11.11.11 SiteB_EXT
access-list inside_outbound_nat0_acl permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
access-list outside_cryptomap_20 permit ip SiteA_INT 255.255.0.0 SiteB_INT 255.255.255.0
access-list acl_inside permit icmp any any
access-list acl_inside permit ip any any
access-list acl_outside permit ip any any
access-list acl_outside permit icmp any any
access-list 80 permit ip SiteA_INT 255.255.0.0 200.220.0.0 255.255.0.0
pager lines 24
mtu outside 1500
mtu inside 1500
mtu webdmz 1500
ip address outside SiteA_EXT 255.255.255.128
ip address inside PIX_INT 255.255.0.0
no ip address webdmz
ip audit info action alarm
ip audit attack action alarm
ip local pool pix_inside 200.x.x.100-200.220.200.150
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
route outside 0.0.0.0 0.0.0.x.x.201.202 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server RADIUS (inside) host 200.200.200.20 letmein timeout 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set AAADES esp-3des esp-md5-hmac
crypto dynamic-map DYNOMAP 10 match address 80
crypto dynamic-map DYNOMAP 10 set transform-set AAADES
crypto map outside_map 20 ipsec-isakmp
crypto map outside_map 20 match address outside_cryptomap_20
crypto map outside_map 20 set peer SiteB_EXT
crypto map outside_map 20 set transform-set ESP-DES-MD5
crypto map outside_map 30 ipsec-isakmp dynamic DYNOMAP
crypto map outside_map client authentication RADIUS
crypto map outside_map interface outside
isakmp enable outside
isakmp key secret address SiteB_EXT netmask 255.255.255.255 no-xauth no-config-mode
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
isakmp policy 30 authentication pre-share
isakmp policy 30 encryption 3des
isakmp policy 30 hash sha
isakmp policy 30 group 2
isakmp policy 30 lifetime 86400
vpngroup Remote address-pool pix_inside
vpngroup Remote dns-server 200.200.200.20
vpngroup Remote wins-server 200.200.200.20
vpngroup Remote default-domain mycorp.co.uk
vpngroup Remote idle-time 1800
vpngroup Remote password password
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
I will attach debug output later today.
Thanks -
Remote Access VPN with existing site-to-site tunnel
Hi there!
I have successfully configured my Cisco router to create a VPN tunnel to Azure. This is working fine. Now I am trying to add a remote access VPN for clients. I want to use IPsec and not PPTP.
I'm not a networking guy, but from what I've read, you basically need to add a dynamic crypto map for the remote access VPN to the crypto map on the external interface (AzureCryptoMap in this case). I've read that the dynamic crypto map should be applied after the non-dynamic maps.
The problem is that the VPN clients do not successfully negotiate phase 1. It's almost like the router does not try the dynamic map. I have tried specifying it to come ahead of the static crypto map policy, but this doesn't change anything. Here is some output from the debugging ipsec and isakmp:
murasaki#
*Oct 6 08:06:43: ISAKMP (0): received packet from 1.158.149.255 dport 500 sport 500 Global (N) NEW SA
*Oct 6 08:06:43: ISAKMP: Created a peer struct for 1.158.149.255, peer port 500
*Oct 6 08:06:43: ISAKMP: New peer created peer = 0x87B97490 peer_handle = 0x80000082
*Oct 6 08:06:43: ISAKMP: Locking peer struct 0x87B97490, refcount 1 for crypto_isakmp_process_block
*Oct 6 08:06:43: ISAKMP: local port 500, remote port 500
*Oct 6 08:06:43: ISAKMP:(0):insert sa successfully sa = 886954D0
*Oct 6 08:06:43: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Oct 6 08:06:43: ISAKMP:(0):Old State = IKE_READY New State = IKE_R_MM1
*Oct 6 08:06:43: ISAKMP:(0): processing SA payload. message ID = 0
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 69 mismatch
*Oct 6 08:06:43: ISAKMP (0): vendor ID is NAT-T RFC 3947
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 198 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 29 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 245 mismatch
*Oct 6 08:06:43: ISAKMP (0): vendor ID is NAT-T v7
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 114 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 227 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 250 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 157 mismatch
*Oct 6 08:06:43: ISAKMP:(0): vendor ID is NAT-T v3
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 164 mismatch
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
*Oct 6 08:06:43: ISAKMP:(0): vendor ID is NAT-T v2
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID seems Unity/DPD but major 242 mismatch
*Oct 6 08:06:43: ISAKMP:(0): vendor ID is XAUTH
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID is Unity
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): processing IKE frag vendor id payload
*Oct 6 08:06:43: ISAKMP:(0):Support for IKE Fragmentation not enabled
*Oct 6 08:06:43: ISAKMP:(0): processing vendor id payload
*Oct 6 08:06:43: ISAKMP:(0): vendor ID is DPD
*Oct 6 08:06:43: ISAKMP:(0):No pre-shared key with 1.158.149.255!
*Oct 6 08:06:43: ISAKMP : Scanning profiles for xauth ... Client-VPN
*Oct 6 08:06:43: ISAKMP:(0): Authentication by xauth preshared
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 1 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 2 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 3 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 4 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 5 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 6 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 7 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 8 against priority 1 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 1 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 2 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 3 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 4 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 5 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 6 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 7 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 8 against priority 2 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 2 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Proposed key length does not match policy
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 3 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 256
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 4 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption AES-CBC
*Oct 6 08:06:43: ISAKMP: keylength of 128
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 5 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 6 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption 3DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 7 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash SHA
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 6 08:06:43: ISAKMP:(0):Checking ISAKMP transform 8 against priority 10 policy
*Oct 6 08:06:43: ISAKMP: life type in seconds
*Oct 6 08:06:43: ISAKMP: life duration (basic) of 3600
*Oct 6 08:06:43: ISAKMP: encryption DES-CBC
*Oct 6 08:06:43: ISAKMP: auth XAUTHInitPreShared
*Oct 6 08:06:43: ISAKMP: hash MD5
*Oct 6 08:06:43: ISAKMP: default group 2
*Oct 6 08:06:43: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 6 08:06:43: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 6 08:06:43: ISAKMP:(0):no offers accepted!
*Oct 6 08:06:43: ISAKMP:(0): phase 1 SA policy not acceptable! (local x.x.x.x remote 1.158.149.255)
*Oct 6 08:06:43: ISAKMP (0): incrementing error counter on sa, attempt 1 of 5: construct_fail_ag_init
*Oct 6 08:06:43: ISAKMP:(0): Failed to construct AG informational message.
*Oct 6 08:06:43: ISAKMP:(0): sending packet to 1.158.149.255 my_port 500 peer_port 500 (R) MM_NO_STATE
*Oct 6 08:06:43: ISAKMP:(0):Sending an IKE IPv4 Packet.
*Oct 6 08:06:43: ISAKMP:(0):peer does not do paranoid keepalives.
*Oct 6 08:06:43: ISAKMP:(0):deleting SA reason "Phase1 SA policy proposal not accepted" state (R) MM_NO_STATE (peer 1.158.149.255)
*Oct 6 08:06:43: ISAKMP (0): FSM action returned error: 2
*Oct 6 08:06:43: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
*Oct 6 08:06:43: ISAKMP:(0):Old State = IKE_R_MM1 New State = IKE_R_MM1
*Oct 6 08:06:43: ISAKMP:(0):deleting SA reason "Phase1 SA policy proposal not accepted" state (R) MM_NO_STATE (peer 1.158.149.255)
*Oct 6 08:06:43: ISAKMP: Unlocking peer struct 0x87B97490 for isadb_mark_sa_deleted(), count 0
*Oct 6 08:06:43: ISAKMP: Deleting peer node by peer_reap for 1.158.149.255: 87B97490
*Oct 6 08:06:43: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
*Oct 6 08:06:43: ISAKMP:(0):Old State = IKE_R_MM1 New State = IKE_DEST_SA
*Oct 6 08:06:43: IPSEC(key_engine): got a queue event with 1 KMI message(s)
*Oct 6 08:06:47: ISAKMP (0): received packet from 1.158.149.255 dport 500 sport 500 Global (R) MM_NO_STATEmurasaki#
*Oct 6 08:06:43: ISAKMP (0): received packet from 1.158.149.255 dport 500 sport 500 Global (N) NEW SA
*Oct 6 08:06:43: ISAKMP: Created a peer struct for 1.158.149.255, peer port 500
*Oct 6 08:06:43: ISAKMP: New peer created peer = 0x87B97490 peer_handle = 0x80000082
*Oct 6 08:06:43: ISAKMP: Locking peer struct 0x87B97490, refcount 1 for crypto_isakmp_process_block
*Oct 6 08:06:43: ISAKMP: local port 500, remote port 500
*Oct 6 08:06:43: ISAKMP:(0):insert sa successfully sa = 886954D0
*Oct 6 08:06:43: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
*Oct 6 08:06:43: ISAKMP:(0):Old State = IKE_READY New State = IKE_R_MM1
If I specify my key like a site-to-site VPN key like this:
crypto isakmp key xxx address 0.0.0.0
Then it does complete phase 1 (and then fails to find the client configuration). This suggests to me that the dynamic map is not being tried.
Configuration:
! Last configuration change at 07:55:02 AEDT Mon Oct 6 2014 by timothy
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
no service dhcp
hostname murasaki
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
aaa authentication login client_vpn_authentication local
aaa authorization network default local
aaa authorization network client_vpn_authorization local
aaa session-id common
wan mode dsl
clock timezone AEST 10 0
clock summer-time AEDT recurring 1 Sun Oct 2:00 1 Sun Apr 3:00
ip inspect name normal_traffic tcp
ip inspect name normal_traffic udp
ip domain name router.xxx
ip name-server xxx
ip name-server xxx
ip cef
ipv6 unicast-routing
ipv6 cef
crypto pki trustpoint TP-self-signed-591984024
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-591984024
revocation-check none
rsakeypair TP-self-signed-591984024
crypto pki trustpoint TP-self-signed-4045734018
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4045734018
revocation-check none
rsakeypair TP-self-signed-4045734018
crypto pki certificate chain TP-self-signed-591984024
crypto pki certificate chain TP-self-signed-4045734018
object-group network CLOUD_SUBNETS
description Azure subnet
172.16.0.0 255.252.0.0
object-group network INTERNAL_LAN
description All Internal subnets which should be allowed out to the Internet
192.168.1.0 255.255.255.0
192.168.20.0 255.255.255.0
username timothy privilege 15 secret 5 xxx
controller VDSL 0
ip ssh version 2
no crypto isakmp default policy
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
lifetime 3600
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 3600
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
lifetime 28800
crypto isakmp key xxx address xxxx no-xauth
crypto isakmp client configuration group VPN_CLIENTS
key xxx
dns 192.168.1.24 192.168.1.20
domain xxx
pool Client-VPN-Pool
acl CLIENT_VPN
crypto isakmp profile Client-VPN
description Remote Client IPSec VPN
match identity group VPN_CLIENTS
client authentication list client_vpn_authentication
isakmp authorization list client_vpn_authorization
client configuration address respond
crypto ipsec transform-set AzureIPSec esp-aes 256 esp-sha-hmac
mode tunnel
crypto ipsec transform-set TRANS_3DES_SHA esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map ClientVPNCryptoMap 1
set transform-set TRANS_3DES_SHA
set isakmp-profile Client-VPN
reverse-route
qos pre-classify
crypto map AzureCryptoMap 12 ipsec-isakmp
set peer xxxx
set security-association lifetime kilobytes 102400000
set transform-set AzureIPSec
match address AzureEastUS
crypto map AzureCryptoMap 65535 ipsec-isakmp dynamic ClientVPNCryptoMap
bridge irb
interface ATM0
mtu 1492
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Ethernet0
no ip address
shutdown
interface FastEthernet0
switchport mode trunk
no ip address
interface FastEthernet1
no ip address
spanning-tree portfast
interface FastEthernet2
switchport mode trunk
no ip address
spanning-tree portfast
interface FastEthernet3
no ip address
interface GigabitEthernet0
switchport mode trunk
no ip address
interface GigabitEthernet1
no ip address
shutdown
duplex auto
speed auto
interface Vlan1
description Main LAN
ip address 192.168.1.97 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Dialer1
mtu 1492
ip address negotiated
ip access-group PORTS_ALLOWED_IN in
ip flow ingress
ip inspect normal_traffic out
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1350
dialer pool 1
dialer-group 1
ipv6 address autoconfig
ipv6 enable
ppp chap hostname xxx
ppp chap password 7 xxx
ppp ipcp route default
no cdp enable
crypto map AzureCryptoMap
ip local pool Client-VPN-Pool 192.168.20.10 192.168.20.15
no ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat translation timeout 360
ip nat inside source list SUBNETS_AND_PROTOCOLS_ALLOWED_OUT interface Dialer1 overload
ip nat inside source static tcp 192.168.1.43 55663 interface Dialer1 55663
ip nat inside source static tcp 192.168.1.43 22 interface Dialer1 22
ip nat inside source static udp 192.168.1.43 55663 interface Dialer1 55663
ip access-list extended AzureEastUS
permit ip 192.168.20.0 0.0.0.255 172.16.0.0 0.15.255.255
permit ip 192.168.1.0 0.0.0.255 172.16.0.0 0.15.255.255
ip access-list extended CLIENT_VPN
permit ip 172.16.0.0 0.0.0.255 192.168.20.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 192.168.20.0 0.0.0.255
ip access-list extended PORTS_ALLOWED_IN
remark List of ports which are allowed IN
permit gre any any
permit esp any any
permit udp any any eq non500-isakmp
permit udp any any eq isakmp
permit tcp any any eq 55663
permit udp any any eq 55663
permit tcp any any eq 22
permit tcp any any eq 5723
permit tcp any any eq 1723
permit tcp any any eq 443
permit icmp any any echo-reply
permit icmp any any traceroute
permit icmp any any port-unreachable
permit icmp any any time-exceeded
deny ip any any
ip access-list extended SUBNETS_AND_PROTOCOLS_ALLOWED_OUT
deny tcp object-group INTERNAL_LAN any eq smtp
deny ip object-group INTERNAL_LAN object-group CLOUD_SUBNETS
permit tcp object-group INTERNAL_LAN any
permit udp object-group INTERNAL_LAN any
permit icmp object-group INTERNAL_LAN any
deny ip any any
mac-address-table aging-time 16
no cdp run
ipv6 route ::/0 Dialer1
route-map NoNAT permit 10
match ip address AzureEastUS CLIENT_VPN
route-map NoNAT permit 15
banner motd Welcome to Murasaki
line con 0
privilege level 15
no modem enable
line aux 0
line vty 0
privilege level 15
no activation-character
transport preferred none
transport input ssh
line vty 1 4
privilege level 15
transport input ssh
scheduler max-task-time 5000
scheduler allocate 60000 1000
ntp update-calendar
ntp server au.pool.ntp.org
end
Any ideas on what I'm doing wrong?Hi Marius,
I finally managed to try with the official Cisco VPN client on Windows. It still fails at phase 1, but now talks about 'aggressive mode', which didn't seem to be mentioned in the previous logs. Any ideas?
*Oct 9 20:43:16: ISAKMP (0): received packet from 192.168.1.201 dport 500 sport 49727 Global (N) NEW SA
*Oct 9 20:43:16: ISAKMP: Created a peer struct for 192.168.1.201, peer port 49727
*Oct 9 20:43:16: ISAKMP: New peer created peer = 0x878329F0 peer_handle = 0x80000087
*Oct 9 20:43:16: ISAKMP: Locking peer struct 0x878329F0, refcount 1 for crypto_isakmp_process_block
*Oct 9 20:43:16: ISAKMP: local port 500, remote port 49727
*Oct 9 20:43:16: ISAKMP:(0):insert sa successfully sa = 886697E0
*Oct 9 20:43:16: ISAKMP:(0): processing SA payload. message ID = 0
*Oct 9 20:43:16: ISAKMP:(0): processing ID payload. message ID = 0
*Oct 9 20:43:16: ISAKMP (0): ID payload
next-payload : 13
type : 11
group id : timothy
protocol : 17
port : 500
length : 15
*Oct 9 20:43:16: ISAKMP:(0):: peer matches *none* of the profiles
*Oct 9 20:43:16: ISAKMP:(0): processing vendor id payload
*Oct 9 20:43:16: ISAKMP:(0): vendor ID seems Unity/DPD but major 215 mismatch
*Oct 9 20:43:16: ISAKMP:(0): vendor ID is XAUTH
*Oct 9 20:43:16: ISAKMP:(0): processing vendor id payload
*Oct 9 20:43:16: ISAKMP:(0): vendor ID is DPD
*Oct 9 20:43:16: ISAKMP:(0): processing vendor id payload
*Oct 9 20:43:16: ISAKMP:(0): processing IKE frag vendor id payload
*Oct 9 20:43:16: ISAKMP:(0):Support for IKE Fragmentation not enabled
*Oct 9 20:43:16: ISAKMP:(0): processing vendor id payload
*Oct 9 20:43:16: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
*Oct 9 20:43:16: ISAKMP:(0): vendor ID is NAT-T v2
*Oct 9 20:43:16: ISAKMP:(0): processing vendor id payload
*Oct 9 20:43:16: ISAKMP:(0): vendor ID is Unity
*Oct 9 20:43:16: ISAKMP : Scanning profiles for xauth ... Client-VPN
*Oct 9 20:43:16: ISAKMP:(0): Authentication by xauth preshared
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 1 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 2 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 3 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 4 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 5 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 6 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 7 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 8 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 9 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 10 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 11 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Preshared authentication offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 12 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 13 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 14 against priority 1 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 1 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 2 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 3 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 4 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 5 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 6 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 7 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 8 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 9 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 10 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 11 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 12 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Preshared authentication offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 13 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 14 against priority 2 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Xauth authentication by pre-shared key offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 2 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 3 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Preshared authentication offered but does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 4 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 256
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 5 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Proposed key length does not match policy
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 6 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 7 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Proposed key length does not match policy
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 8 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption AES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP: keylength of 128
*Oct 9 20:43:16: ISAKMP:(0):Hash algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 9 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 10 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 11 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash SHA
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 12 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption 3DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 13 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth XAUTHInitPreShared
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 3
*Oct 9 20:43:16: ISAKMP:(0):Checking ISAKMP transform 14 against priority 10 policy
*Oct 9 20:43:16: ISAKMP: encryption DES-CBC
*Oct 9 20:43:16: ISAKMP: hash MD5
*Oct 9 20:43:16: ISAKMP: default group 2
*Oct 9 20:43:16: ISAKMP: auth pre-share
*Oct 9 20:43:16: ISAKMP: life type in seconds
*Oct 9 20:43:16: ISAKMP: life duration (VPI) of 0x0 0x20 0xC4 0x9B
*Oct 9 20:43:16: ISAKMP:(0):Encryption algorithm offered does not match policy!
*Oct 9 20:43:16: ISAKMP:(0):atts are not acceptable. Next payload is 0
*Oct 9 20:43:16: ISAKMP:(0):no offers accepted!
*Oct 9 20:43:16: ISAKMP:(0): phase 1 SA policy not acceptable! (local xxxx remote 192.168.1.201)
*Oct 9 20:43:16: ISAKMP (0): incrementing error counter on sa, attempt 1 of 5: construct_fail_ag_init
*Oct 9 20:43:16: ISAKMP:(0): Failed to construct AG informational message.
*Oct 9 20:43:16: ISAKMP:(0): sending packet to 192.168.1.201 my_port 500 peer_port 49727 (R) AG_NO_STATE
*Oct 9 20:43:16: ISAKMP:(0):Sending an IKE IPv4 Packet.
*Oct 9 20:43:16: ISAKMP:(0):peer does not do paranoid keepalives.
*Oct 9 20:43:16: ISAKMP:(0):deleting SA reason "Phase1 SA policy proposal not accepted" state (R) AG_NO_STATE (peer 192.168.1.201)
*Oct 9 20:43:16: ISAKMP:(0): processing KE payload. message ID = 0
*Oct 9 20:43:16: ISAKMP:(0): group size changed! Should be 0, is 128
*Oct 9 20:43:16: ISAKMP (0): incrementing error counter on sa, attempt 2 of 5: reset_retransmission
*Oct 9 20:43:16: ISAKMP (0): Unknown Input IKE_MESG_FROM_PEER, IKE_AM_EXCH: state = IKE_READY
*Oct 9 20:43:16: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_AM_EXCH
*Oct 9 20:43:16: ISAKMP:(0):Old State = IKE_READY New State = IKE_READY
*Oct 9 20:43:16: %CRYPTO-6-IKMP_MODE_FAILURE: Processing of Aggressive mode failed with peer at 192.168.1.201
*Oct 9 20:43:16: ISAKMP:(0):deleting SA reason "Phase1 SA policy proposal not accepted" state (R) AG_NO_STATE (peer 192.168.1.201)
*Oct 9 20:43:16: ISAKMP: Unlocking peer struct 0x878329F0 for isadb_mark_sa_deleted(), count 0
*Oct 9 20:43:16: ISAKMP: Deleting peer node by peer_reap for 192.168.1.201: 878329F0
*Oct 9 20:43:16: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
*Oct 9 20:43:16: ISAKMP:(0):Old State = IKE_READY New State = IKE_DEST_SA
*Oct 9 20:43:16: IPSEC(key_engine): got a queue event with 1 KMI message(s)
*Oct 9 20:43:21: ISAKMP (0): received packet from 192.168.1.201 dport 500 sport 49727 Global (R) MM_NO_STATE
*Oct 9 20:43:26: ISAKMP (0): received packet from 192.168.1.201 dport 500 sport 49727 Global (R) MM_NO_STATE -
Targeted HTTP Requests through SonicWALL Site-to-Site VPN
I have a B2B tunnel to one of our customers. All HTTP/HTTPS traffic from our main office for those addresses goes across the B2B.Now, I have a remote office connected to the main office via site-to-site VPN. How can I target HTTP/HTTPS requests for only the customer websites to use the site-to-site VPN to our office, then the B2B, while allowing other Web traffic to go straight out through the remote office? I have already added the subnets used by the B2B to the access lists at both ends of the site-to-site, but computers at the remote office cannot load Web pages, because the requests are not coming from our B2B IP address. nslookup and ping work from the remote office; DNS is resolving the name to the correct IP address. However, the HTTP/HTTPS requests are going straight out through the remote office firewall without hitting the...
This topic first appeared in the Spiceworks CommunityHi
I looked through the similar questions and I cannot find the answer. My VPN is working correctly and I can ping every LAN interface address objects specified in my routes but I'm unable to ping or access end devices beyond that. IPS and the GAV is not enable since I don't have the licenses, so theirs no concern there. Something is telling me that it could be a basic route needs to be in place on VPN > LAN but that was created in the initial VPN configuration.
For example I can ping Remote LAN interfaces 172.16.0.254, 172.18.0.254 but I cant ping the devices in those subnets.
This topic first appeared in the Spiceworks Community -
Site to Site Tunnel - Traffic just flowing in one direction.
Greetings to everyone,
I have configured an IPSec (Site-to-Site) tunnel between an ASA5510 and a Linux Sytem connection a Network A with a Network B in the following way:
* Diagram:
#---------------IPSec-----------------#
private network (A) ---- Linux Router (GW1) -------- WAN -------- (GW2) ASA5510 ---- public network (B)
* Results:
I have checked the IPSec Tunnel on the linux Router and both Phase 1 and Phase 2 are UP. ASDM shows also an IPSec connection with the correct parameters (GW, Local Network, Left Network etc.).
If I have correctly understand it "show crypto iskmp sa", "show crypto ikev1 sa" and "show crypto ipsec sa" show also that the connection is correct and UP.
*Now comes the interesting thing:
If I ping from Network A to Network B, the icmp echo request go thorugh the tunnel and I can see the Rx bytes on the cisco ASA going UP.
If I ping from Network B to Network A, I do not see any Tx Bytes on the Tunnel. The Linux router does not also see any packets going through the tunnel.
When I ping from Network B to Network A, the Firewall Logs ICMP Denies. That means that the traffic from B to A, I do not know why, is not matching the corresponding Tunnel ACL, the icmp packets are being routed to the default gateway instead through the tunnel and they are then matching a less specific droping rule on the main firewall.
*Configurations:
I have specially configured a Crypto Map that matches the Networks in Both directions.
There exists an ACL that permits the traffic in both directions.
There exist a NAT rules that permits traffic between both networks without being NATed, in order for both networks to transmit through the tunnels freely.
* Ideas ?
crypto map?
NAT?
ACL?
interface level security?
Thanks in advance.Hi Guys,
Thank you all for your help. The packet was being dropped on the "implicit rule", that means that the packet was not finding an ACL to match.
I checked the ACLs that the VPN Wizard generates by itself when used to configure an IPSec connection, and the ACLs where correct and "before" the implicit rule . (They are called by default outside_cryptomap_"number")
It seems that since I am not using "sysopt connection permit-vpn" I have to add the same ACLs to the "Local Network" interface (VPN_LAN).
Since there was inbound ACLs related to the VPN_LAN interface, the firewall jumped directly to the "implicit rule".
So the result is that I have two times the same rules first inbound on the VPN_LAN and second on the default outside_cryptomap ACLs.
Greetings,
Daniel -
Routing Issue for Remote Access Clients over Site to Site VPN tunnels
I have a customer that told me that Cisco has an issue when a customer has a topology of let's say 3 sites that have site to site tunnels built and a Remote Access client connects to site A and needs resources at Site B but the PIX won't route to that site. Has this been fixed in the ASA?
Patrick, that was indeed true for a long time.
But now it is fixed in PIX and ASA version 7.x.
Please refer to this document for details:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml -
Multiple site to site IPSec tunnels to one ASA5510
Question on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall. Any help would be appreciated.
Hi,
Regarding setting up the new L2L VPN connection..
Should be no problem (to my understanding) to configure the new L2L VPN connection through the other ISP interface (0/3). You will need to atleast route the remote VPN peers IP address towards that link. The L2L VPN forming should add a route for the remote networks through that L2L VPN. If not reverse route injection should handle it in the cryptomap configurations.
I guess rest of the setup depends on what will be using the 0/0 ISP and what will be using the 0/3 ISP.
If you are going to put the default route towards the 0/3 ISP you will have to think of something for the 0/0 ISP if some of your local LAN devices are going to use it for Internet also. (Possible routing problems) On the other hand if you have remote VPN Client users using the 0/0 ISP there should be no routing problem for them as they would be initiating connection through that 0/0 ISP link through ASA so ASA should know where to forward the return traffic.
Most of my 2 ISP setups have been implemented with a router in front of the actual ASA/PIX/FWSM firewalls where the router has performed Policy Routing based on the source IP address from the firewalls and then settings the correct gateway towards the correct ISP.
- Jouni -
VoIP QoS for Site-to-Site Tunnel
Hi all,
I need some help with setting up QoS for VoIP between two Cisco ASA 5505 with Site-to-Site VPN.
There is no need for bandwith reservation, only DSCP 46 (EF) should be highest and DSCP 26 second highest queue and the rules should only apply to a site-to-site VPN.
Usually i try to configure the ASAs via ASDM and found out in the Cisco Documentations how to setup QoS for the DSCP bits with a Service Policy and how to set up QoS for a Site-to-Site VPN (Service Policy Rule -> Traffic Match). But how do i configure the QoS for a DSCP bit to only apply to a Site-to-Site Tunnel? And how do i configure different priorities for the two DSCP bits, is this defined by the order of Service Policies?
The QoS has to be enabled on both ASAs for the inside interface?
Thanks in advance
TobiasHi Collin,
ok so from the document i think this has to be added on both ASAs to prioritize DSCP 46. Could you have a quick look if this is all i need?
class-map voice_traffic
match dscp ef
class-map data
match tunnel-group <Tunnel Name>
match flow ip destination-address
policy-map voice_policy
class voice_traffic
priority
class Data
police output 200000 37500
service-policy voice_policy interface outside
But there is still the question how two configure another DSCP bit for priority 2, I could not find out how this is done, neither CLI nor ASDM. Any ideas?
BR
Tobias -
Cisco ASA 5520 Site-to-site VPN TUNNELS disconnection problem
Hi,
i recently purchased a Cisco ASA 5520 and running firmware v. 8.4(2) and ASDM v. 6.4(5)106.
I have installed 50 Site-to-Site VPN tunnels, and they work fine.
but randomly the VPN Tunnels keep disconnecting and few seconds after it connects it self automaticly....
it happens when there is no TRAFIC on, i suspect.
in ASDM in Group Policies under DfltGrpPolicy (system default) i have "idle timeout" to "UNLMITED" but still they keep disconnecting and connecting again... i have also verified that all VPN TUNNELS are using this Group Policie. and all VPN tunnels have "Idle Timeout: 0"
this is very annoying as in my case i have customers having a RDP (remote dekstop client) open 24/7 and suddenly it gets disconnected due to no traffic ?
in ASDM under Monitoring -> VPN .. i can see all VPN tunnels recently disconnected in "Login Time Duration"... some 30minutes, 52minutes, 40minutes and some 12 minutes ago.. and so on... they dont DISCONNECT at SAME time.. all randomly..
i dont WANT the VPN TUNNELS to disconnect, i want them to RUN until we manually disconnect them.
Any idea?
Thanks,
DanielWhat is the lifetime value configured for in your crypto policies?
For example:
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400 -
ASA 5505 site-to-site VPN tunnel and client VPN sessions
Hello all
I have several years of general networking experience, but I have not yet had to set up an ASA from the ground up, so please bear with me.
I have a client who needs to establish a VPN tunnel from his satellite office (Site A) to his corporate office (Site Z). His satellite office will have a single PC sitting behind the ASA. In addition, he needs to be able to VPN from his home (Site H) to Site A to access his PC.
The first question I have is about the ASA 5505 and the various licensing options. I want to ensure that an ASA5505-BUN-K9 will be able to establish the site-to-site tunnel as well as allow him to use either the IPsec or SSL VPN client to connect from Site H to Site A. Would someone please confirm or deny that for me?
Secondly, I would like to verify that no special routing or configuration would need to take place in order to allow traffic not destined for Site Z (i.e., general web browsing or other traffic to any resource that is not part of the Site Z network) to go out his outside interface without specifically traversing the VPN tunnel (split tunneling?)
Finally, if the client were to establish a VPN session from Site H to Site A, would that allow for him to connect directly into resources at Site Z without any special firewall security rules? Since the VPN session would come in on the outside interface, and the tunnel back to Site Z goes out on the same interface, would this constitute a split horizon scenario that would call for a more complex config, or will the ASA handle that automatically without issue?
I don't yet have the equipment in-hand, so I can't provide any sample configs for you to look over, but I will certainly do so once I've got it.
Thanks in advance for any assistance provided!First question:
Yes, 5505 will be able to establish site-to-site tunnel, and he can use IPSec vpn client, and SSL VPN (it comes with 2 default SSL VPN license).
Second question:
Yes, you are right. No special routing is required. All you need to configure is site-to-site VPN between Site A and Site Z LAN, and the internet traffic will be routed via Site A internet. Assuming you have all the NAT statement configured for that.
Last question:
This needs to be configured, it wouldn't automatically allow access to Site Z when he VPNs in to Site A.
Here is what needs to be configured:
1) Split tunnel ACL for VPN Client should include both Site Z and Site A LAN subnets.
2) On site A configures: same-security-traffic permit intra-interface
3) Crypto ACL for the site-to-site tunnel between Site Z and Site A needs to include the VPN Client pool subnet as follows:
On Site Z:
access-list permit ip
On Site A:
access-list permit ip
4) NAT exemption on site Z needs to include vpn client pool subnet as well.
Hope that helps.
Message was edited by: Jennifer Halim -
ISAKMP Phase 1 dying for Site to Site tunnel between ASA and Fortigate
I am facing strange issue on my asa and client Fortigate fw.
We have site to site tunnel with 3des and sha and DH-5 on asa
3des sha1 and dh-5 on Fortigate.
Tunnel came up when configured after some time it went down and it is throwing below errors. Please
some one help me here.
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, IKE SA Proposal # 1, Transform # 1 acceptable Matches global IKE entry # 8
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, constructing ISAKMP SA payload
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, constructing Fragmentation VID + extended capabilities payload
Jul 24 17:25:13 [IKEv1]: IP = X.X.X.X, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + NONE (0) total length : 104
Jul 24 17:25:13 [IKEv1]: IP = X.X.X.X, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + KE (4) + NONCE (10) + NONE (0) total length : 244
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, processing ke payload
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, processing ISA_KE payload
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, processing nonce payload
Jul 24 17:25:13 [IKEv1]: IP = X.X.X.X, Unable to compute DH pair while processing SA!<<<<---------Please suggest if DH group 5 does not work with PSK.
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, IKE MM Responder FSM error history (struct &0xcf9255d8) <state>, <event>: MM_DONE, EV_ERROR-->MM_BLD_MSG4, EV_GEN_DH_KEY-->MM_WAIT_MSG3, EV_PROCESS_MSG-->MM_WAIT_MSG3, EV_RCV_MSG-->MM_WAIT_MSG3, NullEvent-->MM_SND_MSG2, EV_SND_MSG-->MM_SND_MSG2, EV_START_TMR-->MM_BLD_MSG2, EV_BLD_MSG2
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, IKE SA MM:5f1fdffc terminating: flags 0x01000002, refcnt 0, tuncnt 0
Jul 24 17:25:13 [IKEv1 DEBUG]: IP = X.X.X.X, sending delete/delete with reason message
Mum-PRI-ASA#Hey All,
I experienced same issue with my another tunnel. Lately I came to know it was higher level of DH computation which my ASA was not able to perform and ASA reboot worked here. See the logs for tunnel which came up after reboot.
Eror Before Reload
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing ISAKMP SA payload
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing Fragmentation VID + extended capabilities payload
Aug 06 21:17:33 [IKEv1]: IP = xx.xx.xx.xx, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + NONE (0) total length : 416
Aug 06 21:17:33 [IKEv1]: IP = xx.xx.xx.xx, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + NONE (0) total length : 108
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, processing SA payload
Aug 06 21:17:33 [IKEv1]: Phase 1 failure: Mismatched attribute types for class Group Description: Rcv'd: Group 5 Cfg'd: Group 2
Aug 06 21:17:33 [IKEv1]: Phase 1 failure: Mismatched attribute types for class Group Description: Rcv'd: Group 5 Cfg'd: Group 2
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Oakley proposal is acceptable
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, processing VID payload
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Received Fragmentation VID
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, IKE Peer included IKE fragmentation capability flags: Main Mode: True Aggressive Mode: True
Aug 06 21:17:33 [IKEv1]: IP = xx.xx.xx.xx, Unable to compute DH pair while processing SA!
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, IKE MM Initiator FSM error history (struct &0xd0778588) , : MM_DONE, EV_ERROR-->MM_BLD_MSG3, EV_GEN_DH_KEY-->MM_WAIT_MSG2, EV_PROCESS_MSG-->MM_WAIT_MSG2, EV_RCV_MSG-->MM_WAIT_MSG2, NullEvent-->MM_SND_MSG1, EV_SND_MSG-->MM_SND_MSG1, EV_START_TMR-->MM_BLD_MSG1, EV_BLD_MSG1
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, IKE SA MM:64cf4b96 terminating: flags 0x01000022, refcnt 0, tuncnt 0
Aug 06 21:17:33 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, sending delete/delete with reason message
Isakmp phase completion After reload
Aug 25 10:40:35 [IKEv1]: IP = xx.xx.xx.xx, IKE_DECODE RECEIVED Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + NONE (0) total length : 108
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, processing SA payload
Aug 25 10:40:35 [IKEv1]: Phase 1 failure: Mismatched attribute types for class Group Description: Rcv'd: Group 5 Cfg'd: Group 2
Aug 25 10:40:35 [IKEv1]: Phase 1 failure: Mismatched attribute types for class Group Description: Rcv'd: Group 5 Cfg'd: Group 2
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Oakley proposal is acceptable
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, processing VID payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Received Fragmentation VID
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, IKE Peer included IKE fragmentation capability flags: Main Mode: True Aggressive Mode: True
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing ke payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing nonce payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing Cisco Unity VID payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing xauth V6 VID payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Send IOS VID
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Constructing ASA spoofing IOS Vendor ID payload (version: 1.0.0, capabilities: 20000001)
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, constructing VID payload
Aug 25 10:40:35 [IKEv1 DEBUG]: IP = xx.xx.xx.xx, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Aug 25 10:40:35 [IKEv1]: IP = xx.xx.xx.xx, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + KE (4) + NONCE (10) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 320
SENDING PACKET to xx.xx.xx.xx
Maybe you are looking for
-
Normally, when I click on Bookmarks at the top of my screen, the list of websites that comes up includes a little icon to the left of each bookmark. Now I only get a list. No icons. What has happened to the little four-colored flag for Hotmail, the '
-
My lower right screen touch of iphone 4 is not functioning proper . I have to press hard to make it go. and my letter "o" it not functions while typin a message. please help
-
Retrieve as many duplicate records as a value stored in one of the columns
Hi, I have a peculiar requirement where I want multiple copies of rows the count of which is determined by one of the column values: create table test (id number, value number, data varchar2(100)); insert into test values (1,5,'one'); insert into tes
-
Add new Alerts to system monitoring
Hi, My Name is Tomas Piqueres and I'm working with Solution Manager. I'm monitoring one of my systems and I'm setting up some alerts. The problem is when I'm trying to add some alerts that are outside the last node (the corresponding with the server
-
Cannot pause the iCloud photo upload for one day at iOS 8.3
In the faq "https://support.apple.com/en-us/HT204264", it mentions that there is a button to pause the photos upload at "Settings > iCloud > Photos" but it's not there. Can anyone find it?