SL500 Tape library Issue

Hi Every one here
I need some help with the SL500 Tape library
I need to connect to the Library through the CLI port so I need to know the connection pin configuration
I'll tell u what I do & any one who knows the connection tells me if it's wrong or what ?
1)I'm using RJ-45 straight cable to connect to the CLI port
2)from my lap top side I use usb-to-serial converter
3)between both of them there is a converter which have DB-9 female from a side & RJ-45 interface from the other side which is the one that comes along with most of the sparc servers
is this right ? or there is some special converters that comes along with the Tape library which may be had been lost in the customer site ? & if so can any one tell me the pin configuration of this converter & I will made up one ? if not may be the problem in the Straight RJ-45 cable which I use may be it's the wrong one knowing that I tried also cross-over & roll-over cables ?
I tried to login using the admin username from the cross-over connection between me labtop & the library
I use the Putty tool to ssh the IP address of the library when I type thw admin it prompts me the password & as sson as I type the password & press enter it logs me off
why Can't I login to the CLI using ssh throught the ethernet cable or must I login to the library from the CLI port ???
Regards

Hi,
There is a special DB9-RJ45 connector that comes with each STK/Sun libraries. You'll need it to establish a CLI connection. Server adapters does not function in libraries.
Regards

Similar Messages

  • SL500 tape library and IBM LT0 5 tape drive Firmware locations

    Hi All,
    I need the locations or the url to download the latest firmware for SL500 Tape Library and IBM LT0 5 Tape Drives.
    Regards,
    Joseph

    However, IBM LTO5 firmware is available for download by customer via support.oracle.com / patches and updates. Just search for 145784-08.
    Product Family
    Drive Supplier
    Drive Firmware
    Drive Patch
    LTO-5 (FC 8Gb)
    IBM
    D8D4
    145784-08

  • Robotics error and issue within SL24 Tape library with Solaris 10

    Dear All,
    Kindly may any one help me with this issue or at least give me a hint about where to begin thinking about the solution from
    I have a tape library SL24 which is attached to the server V240 my backup server on which the robotics is not seen by the veritas net backup and when I try some commands like
    #sgscan
    the robotics isn't discovered
    the Veritas docs says that this is issue is related to the Solaris OS
    so can any one give me what are the possible causes to that error ?
    knowing that there is no zoning in this datacenter

    Did this configuration of your V240 and the SL24 ever work?
    Here's the documentation for the SL24:
    http://docs.oracle.com/cd/E25510_01/index.html
    Here's the documentation for the V240:
    http://docs.oracle.com/cd/E19088-01/v240.srvr/index.html
    I have a tape library SL24 which is attached to the server V240 ,,, attached to what? I don't think the integrated SCSI port is compatible and therefore you'll need to buy and install an appropriate HBA for the computer.
    Start with the documentation.

  • Backup Oracle VMs using a direct attached tape library

    Hello all,
    I'm in the process of getting a specification for a new Oracle VM host server which will run OEL VMs and host Oracle databases (10g and others), currently we're looking at getting an HP DL580 and a MSL6000 tape library using SAS connectors.
    Regarding backups, I understand that Oracle VM Server doesn't have a built in mechanism for backups so would need to use a backup method from within the virtual machines.
    Is it possible, and advisable, to use a tape library directly attached to the host server and use an OEL VM running Symantec Netbackup which will then backup the other VMs, if so, are there any issues or gotchas I should be aware of?
    If it is possible to do this, do I connect the tape library to the VM by editing the VM config file and add the tape library devices as 'phy:/dev/xxx'
    Thanks in advance,
    Martin.
    Edited by: user5385211 on 09-Oct-2009 03:39

    NDMP is for backing up NAS platforms.
    Does your backup software support "LAN-Free" backup ? Typically enterprise backup software like Netbackup, TSM, Networker require a special license/agent that gets loaded on server where you are going to implement LAN-Free backups. Without that software/license servers will be fighting for tape resources and it will be a mess (if it works at all). Also you want to use dedicated HBA or port on dual HBA for tape traffic, do not mix tape and disk traffic on the same HBA/port. In big shops people configure dedicated "tape" VSANs but that would be an overkill for your current environment.
    @dynamoxxx

  • Tape Library Concern - Eject & Reinsertion after each backup

    Here is what I am currently using.
    System overview:
    -HP Proliant DL380p Gen 8
    -HP D2600 2TB 3G SATA LFF - 24TB Storageworks array
    -Quantum Scalar i40
    (2) HP LTO-5 tape heads
    (25) Licensed slots
     Tape library is configured as one partition
    Windows 2012 R2 - fully patched
    DPM 2012 R2 Data Center Edition with 7/2014 Update Rollup 3
     I have used DPM for about 6 years since 2007 version but I have always used stand alone LTO-3 & LTO-5 tape drives.  I
    have used tape libraries before that time but with a different product.
    Here is the scenario I am seeing.  Any tapes jobs that are scheduled at the same time will
    pull a tape into each tape drive and backups are performed.  All is working normal from that perspective.  The problem I see is that after each backup is completed the tape is removed from the drive, placed back in the slot, removed again from the
    slot and then re-inserted back into the drive to continue with the next backup job that was scheduled at the same time as the previous one.
    This seems highly inefficient and time consuming not to mention a lot of extra wear & tear
    on the library & tapes.  Is this behavior normal? If so, can it be changed?  or is it is bug?
    I would expect the tape to remain in the tape drive until all backups are completed assuming they
    had available capacity and were not off-site ready.  It appears if multiple servers are in the same protection group the tape is not removed between these backups.  The issue appears to be when the next separate protection group is backed up.
    I’d even be up to manually moving the tape and leaving it in the tape in drive but I don’t see
    that kind of library control with DPM.
    I saw another thread from August where someone mentioned seeing this behavior when doing verifies
    on their backups.
    Thoughts?  PSS call?
    Thanks!

    I'm seeing that if a protection group consisting of hundreds of small SQL databases is configured for short term disk and long term tape, and configured to use 2 drives, that after EACH DATABASE the tape is rewound and re-slotted, only to be re-inserted
    into the drive and fast forwarded to the end for the next database to be written.
    If you've got hundreds of databases (many small, like msdn, model, etc) this can push the time out to 3 minutes plus per database taped, even for a 5MB database.
    My current workaround is to configure the protection group to only allow the use of a single drive.
    Doing so seems to reduce the time per database from 5 minutes down to 30 seconds, presumably just REW and FF tape movement.
    Even though the time is reduced, I'm still disappointed the progress between databases doesn't continuously stream.  I mean 100 small 5MB databases should only take 7 seconds, if streaming at 70MB/s to tape.  Instead it's 30 seconds per 5MB database. 
    :(

  • Integration of RMAN with virtual tape library

    OS: Oracle Linux 5.5 UEK (Virtualbox)
    Oracle: 11gR2 11.2.0.1 Enterprise + ASM (Virtualbox)
    Hello,
    I would like to test something about RMAN and writing directly to tape. For this I installed mhvtl, a virtual tape library. The installation was pretty easy. http://sites.google.com/site/linuxvtl2/
    RMAN does not recognize any tape in the system.
    ORA-19554: error allocating device, device type: SBT_TAPE, device name:
    ORA-27211: Failed to load Media Management Library
    What I found out is that in order to make backups to a media manager, RMAN must communicate with a media management library, which is a 3rd party library that is not supplied by Oracle. So I guess unless there is a Oracle MML library available for mtx I' out of luck here.
    Any ideas? Thanks!
    rpm -ivh mhvtl-0.18-13.x86_64.rpm
    rpm -ivh mhvtl-0.18-13.src.rpm
    cd /usr/src/redhat/SOURCES/
    tar zxvf ../SOURCES/mhvtl-2011-01-11.tgz
    cd mhvtl-0.18/kernel
    make
    make install
    /etc/init.d/mhvtl start
    yum install mtx
    The tape library and using it for backup from system seems to work fine:
    # mtx status
    Storage Changer /dev/changer:4 Drives, 43 Slots ( 4 Import/Export )
    Data Transfer Element 0:Full (Storage Element 1 Loaded):VolumeTag = E03001L4
    etc.
    # mtx load 1
    Drive 0 Full (Storage Element 1 loaded)
    # tar cf /dev/ntape ./
    # tar tvf /dev/ntape
    Edited by: Dude on Jan 20, 2011 5:22 PM

    Thanks for the tip!
    I installed Oracle Secure Backup Express and spend all afternoon with this strange product, mainly to troubleshoot the installation and setup. I'm not really sure everything works - it's quite a piece of software, as usual.
    I ran into a couple of issues that were not mentioned in the installation documentation:
    - install sg3_utils
    - use obtool to register the server as mediaserver
    # sg_map -i -x
    /dev/sg9 3 0 1 0 1 /dev/nst0 IBM ULT3580-TD5 550V
    /dev/sg10 3 0 2 0 1 /dev/nst1 IBM ULT3580-TD5 550V
    /dev/sg11 3 0 3 0 1 /dev/nst2 IBM ULT3580-TD4 550V
    /dev/sg12 3 0 4 0 1 /dev/nst3 IBM ULT3580-TD4 550V
    /dev/sg13 3 0 9 0 1 /dev/nst4 IBM ULT3580-TD4 550V
    /dev/sg14 3 0 10 0 1 /dev/nst5 IBM ULT3580-TD4 550V
    /dev/sg15 3 0 11 0 1 /dev/nst6 IBM ULT3580-TD4 550V
    /dev/sg16 3 0 12 0 1 /dev/nst7 IBM ULT3580-TD4 550V
    /dev/sg17 3 0 0 0 8 STK L700 550V
    /dev/sg18 3 0 8 0 8 SPECTRA PYTHON 550V
    # obtool
    ob> chhost --addrole mediaserver ol55
    ob> mkdev -t library -o -a ol55:/dev/sg18 library1
    ob> mkdev -t tape -o -a ol55:/dev/sg9 -l library1 -d 1 tape1
    RMAN was not happy with it:
    ORA-19554: error allocating device, device type: SBT_TAPE, device name:
    ORA-27023: skgfqsbi: media manager protocol error
    ORA-19511: Error received from media manager layer, error text:
    sbt__rpc_connect: Internal error - could not connect to obproxyd (Oracle Secure Backup error: 'bad port name specified (OB SBT proxy manager)').
    # cat /usr/tmp/obproxyd.log
    2011/01/23.02:11:10 [5431] can't set root privileges; continuing anyway - program isn't stamped setuid-root (OB utilities)
    2011/01/23.02:11:10 [5431] can't listen for connections - Operation not permitted
    Document ID 396046.1 solution outlines to correct the hostname or mediaserver name. However, this was not the problem. I finally figured that /etc/obproxyd is a symlink to a .wrapper script which points to the actual proxy application. The fix was:
    #chmod +s /usr/local/oracle/backup/.etc.linux86_64obproxyd
    After this the error changed:
    RMAN-03009: failure of backup command on ORA_SBT_TAPE_1 channel at 01/23/2011 02:43:36
    ORA-19506: failed to create sequential file, name="3cm2q2an_1_1", parms=""
    ORA-27028: skgfqcre: sbtbackup returned error
    ORA-19511: Error received from media manager layer, error text:
    sbt__rpc_cat_query: Query for piece 3cm2q2an_1_1 failed.
    (Oracle Secure Backup error: 'no preauth config found for OS user (OB tools) oracle').
    The fix for this error:
    https://10.0.0.6, login as 'admin'
    Configure->Users->Select Admin->Edit->Preauthorized Access->Add user 'Oracle' (select host and rman)
    RMAN> backup database;
    Starting backup at 23-JAN-11
    using channel ORA_SBT_TAPE_1
    channel ORA_SBT_TAPE_1: starting full datafile backup set
    channel ORA_SBT_TAPE_1: specifying datafile(s) in backup set
    input datafile file number=00001 name=/scratch/oradata/test/system01.dbf
    input datafile file number=00002 name=/scratch/oradata/test/sysaux01.dbf
    input datafile file number=00003 name=/scratch/oradata/test/undotbs01.dbf
    input datafile file number=00005 name=/scratch/oradata/test/users02.dbf
    input datafile file number=00004 name=/scratch/oradata/test/users01.dbf
    channel ORA_SBT_TAPE_1: starting piece 1 at 23-JAN-11
    Now it just sits there forever and the log just keeps adding the following lines:
    # cat obproxyd.log
    2011/01/23.03:00:31 [5662] handle_qsp_msg: received get job state request
    2011/01/23.03:00:31 [5662] job id 'admin/5.1'
    Strange, backup to tape with 'mtx' and 'tar' works, so the problem might be OSB.
    Edited by: Dude on Jan 22, 2011 8:32 PM
    I finally got it running. I deleted the current library and drive configuration and used the webtool to configure the other library at /dev/sg17. it was also necessary to use the webtool to load a volume into the drive. Unfortunately I did not note down the steps in details. Maybe next time.
    channel ORA_SBT_TAPE_1: starting piece 1 at 23-JAN-11
    channel ORA_SBT_TAPE_1: finished piece 1 at 23-JAN-11
    piece handle=3im2qc42_1_1 tag=TAG20110123T053042 comment=API Version 2.0,MMS Version 10.2.0.3
    channel ORA_SBT_TAPE_1: backup set complete, elapsed time: 00:03:26
    Finished backup at 23-JAN-11
    Starting Control File and SPFILE Autobackup at 23-JAN-11
    piece handle=c-2036659790-20110123-00 comment=API Version 2.0,MMS Version 10.2.0.3
    Finished Control File and SPFILE Autobackup at 23-JAN-11

  • Quantum P2000 tape library showing NOBARCODE on tape drive

    Hi all,
    We are having a tape library of ATL quantum P2000 which is having 4 tape drives.
    In which we used to daily backup.
    When ever we are keeping any new cartridges into the library we will run an inventory , During this time if their is any kind of cartridge in the tape drive their wont be any issue with that particular tape drive .
    If not it is showing a problem of NO BAR CODE on the operator panel of the library.
    and at this time it is not detecting on the legato software also.
    Kindly help me in this .....
    Thanks in Advance....
    SWAROOP

    I will use new words to repeat my first reply:
    You have broken hardware.
    Broken hardware doesn't work when you expect it to work.
    For example:
    but why my tape drive is showing no bar code error when no tape is presentHow can a broken barcode reader give you an error when you don't have anything in the library that has a barcode on it?
    Go contact whoever you use for repair services and get the library repaired.

  • STK L 700 tape library robot holding the media.

    Hello All,
    I have an STK L700 tape library, which has 4 HP LTO3 FC tape drives and 2 IBM LTO4 FC tape drives, the robot is FC connected.
    I have an issue,The hand assembly picks the media from tape drives after backup and then goes to a slot and holds the media for a long time, then after we eject the media. then i can see a message, initialization failed.
    This issue is intermitent.
    I checked the FSC logs and I could find 3 FSC logs with reach alert.
    &&309D
    &&3087
    &&3087
    I have checked the physical library status, it is working normally, after we take out the media and re initialize it.
    I dont think this could be due to hardware failure, anyone could you kindly help me out to isolate the issue?

    Cross-posted to the Storage forum:
    [t-5381933]

  • SP500 tape library - how many server/SAN FC interfaces do I need?

    How many server or FC switch interfaces do I need to connect SL500 FC tape library? Let's say we have two FC tape drives installed. Does it mean I need to reserve 3 FC interfaces (one for robot and one for each drive)? Or there is some kind of internal hub/switch which permits to use one FC port to connect them all in a way which is implemented in SL48 library?

    Hello,
    if one VMWare host should run more then 2 VMs you need a Windows Server 2012 R2 Datacenter edition (unlimited versions from Windows VMs on the host) from Windows or 7 Windows Standard licenses (max. 14 VMs).
    Keep in mind that processors count into the license requirements.
    "...using VMware for high availability..."
    This means that you should have at least 2 VMWare hosts which have the RAM and processors to run in caseof hardware problem from the other host ALL VMs.
    So you are now need at least 2 Windows Server 2012 R2 Datacenter licenses or 14 Standard editions.
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://blogs.msmvps.com/MWeber
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
    Twitter:  

  • OSB with a (non-supported) virtual tape library

    For testing and learning purposes, I have installed OSB 10.3 and the virtual tape management system mhvtl (http://mhvtl-linux-virtual-tape-library-community-forums.966029.n3.nabble.com/MHVTL-Linux-Virtual-Tape-Library-Getting-Started-td1663811.html). It seems to work quite well apart from one serious shortcoming. If a virtual tape which is already labeled and used as part of a media family is unmounted from the drive, a subsequent re-mount leads to a relabel of the volume whereupon all pieces and any reference to the volume are lost. If the virtual tape is left in the drive, there is no issue - new backups are appended to the end of the volume as one would expect.
    Somewhat perversely, when I mount a used tape, OSB correctly identifies it. As soon as I start writing to it though, the volume is re-labeled.
    I can overcome the issue by using obtar -z to advance the tape to the end of the volume.
    % obtar -zf VDAT72
    Volume label:
    Volume UUID: d4c93502-15a0-102e-b7f5-00163e319d06
    Volume ID: RMAN-DENVER-000025
    Volume sequence: 1
    Volume set owner: root
    Volume set created: Tue Feb 08 13:02:21 2011
    Media family: RMAN-DENVER
    Volume set expires: never; content manages reuse
    Original UUID: d4c93502-15a0-102e-b7f5-00163e319d06
    Archive label:
    File number: 4
    File section: 1
    Owner: root
    Client host: node1
    Backup level: 0
    S/w compression: no
    Archive created: Tue Feb 08 13:09:26 2011
    Backup piece name: c-3970187662-20110208-03
    Backup db name: denver
    Backup db id: 3970187662
    Backup copy number: not applicable
    Backup content: autobackup
    $ obtar -zf VDAT72
    Error: no backup image at current position -- end of volume set.
    At this point, any new backup starts writing to the virtual tape at the current position, and existing files on the volume are preserved - no re-label is carried out.
    I'd like to debug OSB but when I try to set up debugging on the volume, I get:
    $ obtool labelvol obtaropt J  drive VDAT72
    Error: Label/reuse operation requires that you specify no names or BDFs.
    If anyone has some clues, I would be grateful.
    Edited by: Graeme Lawton on Feb 8, 2011 2:12 PM
    Edited by: Graeme Lawton on Feb 8, 2011 2:13 PM

    For testing and learning purposes, I have installed OSB 10.3 and the virtual tape management system mhvtl (http://mhvtl-linux-virtual-tape-library-community-forums.966029.n3.nabble.com/MHVTL-Linux-Virtual-Tape-Library-Getting-Started-td1663811.html). It seems to work quite well apart from one serious shortcoming. If a virtual tape which is already labeled and used as part of a media family is unmounted from the drive, a subsequent re-mount leads to a relabel of the volume whereupon all pieces and any reference to the volume are lost. If the virtual tape is left in the drive, there is no issue - new backups are appended to the end of the volume as one would expect.
    Somewhat perversely, when I mount a used tape, OSB correctly identifies it. As soon as I start writing to it though, the volume is re-labeled.
    I can overcome the issue by using obtar -z to advance the tape to the end of the volume.
    % obtar -zf VDAT72
    Volume label:
    Volume UUID: d4c93502-15a0-102e-b7f5-00163e319d06
    Volume ID: RMAN-DENVER-000025
    Volume sequence: 1
    Volume set owner: root
    Volume set created: Tue Feb 08 13:02:21 2011
    Media family: RMAN-DENVER
    Volume set expires: never; content manages reuse
    Original UUID: d4c93502-15a0-102e-b7f5-00163e319d06
    Archive label:
    File number: 4
    File section: 1
    Owner: root
    Client host: node1
    Backup level: 0
    S/w compression: no
    Archive created: Tue Feb 08 13:09:26 2011
    Backup piece name: c-3970187662-20110208-03
    Backup db name: denver
    Backup db id: 3970187662
    Backup copy number: not applicable
    Backup content: autobackup
    $ obtar -zf VDAT72
    Error: no backup image at current position -- end of volume set.
    At this point, any new backup starts writing to the virtual tape at the current position, and existing files on the volume are preserved - no re-label is carried out.
    I'd like to debug OSB but when I try to set up debugging on the volume, I get:
    $ obtool labelvol obtaropt J  drive VDAT72
    Error: Label/reuse operation requires that you specify no names or BDFs.
    If anyone has some clues, I would be grateful.
    Edited by: Graeme Lawton on Feb 8, 2011 2:12 PM
    Edited by: Graeme Lawton on Feb 8, 2011 2:13 PM

  • DPM 2012 Tape library changer sharing

    I setup tape library sharing on one of my three DPM 2012 servers. I then retired that server. I'm now trying to share the changer out on another server. I'm able to see the changer in the device settings of the new DPM server. I can see the tape library
    in the administrator console, but when I run a rescan it fails with the following errors, referencing my retired DPM 2012 servers.
    DPM failed to communicate with the protection agent on CCDPM2012SRV3 because access is denied. (ID 42 Details: Access is denied (0x80070005))
    DPM failed to communicate with ccdpmp01.ccounty.com because the computer is unreachable. (ID 41 Details: The RPC server is unavailable (0x800706BA))
    Is there a config. setting within DPM that may be looking at these server?

    Hi,
    You will need to
    remove library sharing, then re-enable library sharing so you can switch library control servers.
    There is a good chance that re-enabling library sharing may fail with an error "Failed
    to execute SharedLibraryConfigureDb.sql on DPMSERVER" because DPM 2012 has an issue where it does not clean up properly - this is being addressed in a future Update. 
    If that does occur, then open a support ticket and have the DPM Support engineer reference ID2785571 to help cleanup - you will not be charged since it's a know issue.
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
    posting is provided "AS IS" with no warranties, and confers no rights.

  • New SCDPM 2012 Deployment Scenario and tape Library Sharing.

    Folks
    I am having one SCDPM 2012 SP1 on Server 2008 R2 with one tape library. I am going to build another second DPM on Server 2012 and I want to share the same library which is on first DPM.
    Before I build second DPM server I want to make some doubts clear so it does't create issues later.
    Both DPM will be physical.
    I am reading technet link to share tape ibrary : http://technet.microsoft.com/en-us/library/hh758124.aspx
    And My queries are:
    1) The tape library must be in a storage area network (SAN) environment.
     >The tape Hewlett Packard LTO Ultrium-5 drive I have is attched to first DPM server through SCSI array.Dont know if it is SAN supported.
    2) We recommend that the system configuration of the library server computer and all library client computers be as similar as possible, and that you do not configure any protection groups on the library server.
       >As I have attached library to my first DPM server which is having 22 Protection groups with 562 datasources. Can it be promoted as a Library server? If not then what is solution for this.
    3)All DPM servers using a shared library must use a similar SQL Server setup for hosting DPM databases.You cannot have some DPM servers using local instance and others using a remote instance.
       >My first DPM is hosting its Database on its own (local) So should I setup SQL on second DPM localy?
    4)SQL accounts should be DOMAIN accounts? On the technet link it is showing SQL failover cluster, where does it require? As image showing it is required between library clients but I will have one library server and one library client, will I needed SQL CLuster?
    This was related to Tape, now other queries I have if second DPM and tape sharing deployed successfully.
    1) First DPM has reached LDM records occupancy 79% and I have identified non-colocated datasources/Protection groups which are occupying larger amount of LDM. I will move/recreate these protected groups on 2nd DPM with COLOCATION so they cant use much LDMs.
       a)Should I stop protection on 1st DPM and add these protection groups on 2nd DPM. Will it allow me to add since Inactive replica there would be on 1st DPM for 30days
       b) Or should I Migrate these PGs?
       c) What is best practice for this?

    Figured it out.  Since I'm on a preconfigured RDS server, the RDS Session Host role is already installed.  So technically Session-based desktop deployment is already set up.  It's the difference between the session host role and the Virtualization
    Host roles...slightly confusing when you walk into the middle of the deployment.
    It would also explain my second part of the question since the session host role is installed....

  • Xserver Fibre Channel with tape backup issues?

    Is this correct, that OS X 10.4.9 and 10.4.10 has a fibre channel issue with external tape drives (as well as SCSI drives)???
    And this is to be fixed in 10.4.11? Do we have a time frame when we will see 10.4.11 to fix this major snafu?
    I'm going to decide on a different server (in the meantime) and do net backups if this is the case. But what about others that run backup off the server, attached to an Xserve RAID?
    BTW, I contacted BRU support with query on their software...I give kudos to them. Their support is spot on!
    Message was edited by: Eddie Ski

    Retrospect is just hideously, egregiously out of date and I don't think EMC gives a d*mn, at all.
    Even pre-Intel, it will happily LOCK up your server while failing to properly time out when trying to talk to a tape library. It's well-known, Retro + Tape Library = h*ll on earth. And the fault lies squarely with Retro because something like Bru and other more expensive software does not have the same issue.
    So let's just make sure -not- to judge "SCSI" isues in OS X based on the ungodly-awful behaviour of Retrospect. Might as well do automobile performance tests using only amateur drivers ; )

  • How to Create Virtual Tape Library for RHEL 5.4

    Hi,
    We are planning to use a tape library (well, as our team proposed) so we are trying to create a Virtual Tape Library as a proof of concept on this project. Can you help us create virtual tape libraries using raw devices.
    We will be using Virtual Box as our virtualization environment which will run RHEL 5.4. Will this be possible?
    Thanks and hope you can give us some ideas.

    I tried the exact same setup and it is possible. What you will need is mhvtl and Oracle OSB to get a Oracle Media Management Library (MML).
    Please see Integration of RMAN with virtual tape library
    The link above should provide the setup info you will need. There were some initial problems, but according to follow up posts later versions of the products seem to have fixed the issues with tape handling.

  • Tape- configuration issue

    Executed as user: alq. Mount tape for BACKUP DATABASE of database 'ALQ
                ' on tape drive '\\.\tape0'. [SQLSTATE 42000] (Error 4027).  The step
                failed.
                        <------------- End of Job Step History --------------->
    Hi,
    I have received the above error while schedule the backup in SAP Drive 1
    While scheduling , we have selected the device name as R3DUMP0 ( Drive 1) in SAP level but the backup is happening in  Drive 2 (R3DUMP1) tape in Tape library. 
    Please suggest to resolve this issue.

    You have asked your query in the SAPGUI section of the SCN forums,
    You are unlikely to get a qualified response here:
    Please do a search before posting a new query.
    Regards.
    Jude

Maybe you are looking for

  • Delete files from itunes library?

    after you've loaded a bunch of songs onto your ipod, will it affect your ipod if you delete them from the itunes library?

  • Problems with PS CS4 and sketch tablet

    I having problems with my sketch tablet everytime I start PS CS4 I only can use my primary screen with the pen.. As long as CS4 is not running I can use the dual screen without problems. Anyone have any clues how to fix it? I have the latest drivers.

  • N97 firmware update 21.2

    The update seems to be great with the following exeption:   It has rendered the music player almost unusable! With the previous music player, you could press the "Back" button and it would take you to your list of music or podcasts.  Now the  "Back"

  • Warning on Unsaved Changes Functional Pattern --Help!

    Is there anyone out there who knows how to make this work??!! [http://www.oracle.com/technology/products/adf/patterns/11.1.1.1.0/UnsavedDataWarning.html] Help!

  • Jagged Text using Cameras and Motion 3

    Hello, Using Motion 3. We have an issue when we use the camera to travel through various text titles in 3D. The camera works fine, but the text itself is very aliasy - even though we are working in an HD environment. I believe my problem is that the