SLD Client Settings for ECC 6.0 IDES system

Hello Friends
I want to configure the SLD Client settings in teh ECC 6.0.
Can you suggest me the correct guide or steps to follow in order to proceed??
Thanks in advance.
Regards
Pooja

Hi Pooja,
Please refer to the document available @ below mentioned link.
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/50924080-0627-2a10-2b89-8cb87b972fb1
Page number 45 onwards will be useful for you. Please read & then perform
Also for more details refer System Landscape Directory (SLD)
NOTE : This is only applicable , if you are configuring SLD for NW 7.0 underlying engine.
I hope the provided information will help. Please revert for further clarification/details.
Best Regards,
~~ Pradeep Bishnoi ~~

Similar Messages

  • System Config for ECC 6.0 IDES

    Hi all..
    what's the  system requirement for ecc 6.0 ides ...
    okay  bye

    Hi,
    Hardware Requirement for Central System
    I. Minimum disk space
    1. Database Software
    1 GB (x64)
    2 GB (IA64)
    2. SAP system files (not including paging file)
    5 GB (x64)
    8 GB (IA64)
    3. SAP database files (not including paging file)
    76 GB
    4. 4.3 GB of temporary disk space for every required installation DVD that you have to copy to a local hard disk
    II. Minimum RAM 4GB
    III. Paging file size 1 times RAM plus 8 GB
    Hardware Requirements for a Distributed System
    I. Minimum disk space
    1. Database software
    1 GB (x64)
    2 GB (IA64)
    2. Database instance (not including paging file)
    76 GB
    3. Central instance (not including paging file)
    5 GB (x64)
    8 GB (IA64)
    4. In addition you require 4 GB (x64), or 8 GB (IA64) per additional platform.
    5. Dialog instance (optional) (not including paging file)
    2.5 GB (x64)
    5 GB (IA64)
    5. Temporary disk space for every required installation DVD that you have to copy to a local hard disk:
    4.3GB
    II. Minimum RAM 2 GB
    III. Paging file size n Database instance
    1.5 times RAM
    Central instance:
    1 times RAM plus 8 GB
    Dialog instance (optional)
    1 times RAM plus 8 GB
    These all data you can find in the Installation Guide for ECC6.0
    Thanks,
    Nitesh Jain

  • Client Settings for SM 4.0

    Hi Experts,
    Can any one explain the client settings in Single SM land scape.
    My solman is prompting for Transport Request while I do some SPRO settings.
    What is standard client setting for single solman client.
    Thanks
    Samba

    Hi Kata,
    if you only have one SM client, you can change the client settings in SCC4 so as the system will not ask you for transport requests.
    nevertheless, depending the number of people involed in working on the seetings of SOLAMN, i would recommend to set up the transport requests, just for the sake of keeping  a better control of what is being modified, although these transport requests won´t be transported to any other system and/or client.
    In my case, I have only one SOLMAN system, with only one working client. The majority of the SOLMAN customizing has been performed without having to store the information in transport requests although I have in SE06 the system set as modifiable, and in SCC4.
    automatic recording of changes for client dependent objects
    and "Changes to Repository and cross-client Customizing " option set in Cross-Client Object Changes.
    This setting is not prompting for change requests when setting up SMSY (for example), but obligues me to register in transport changes any OSS Note which I have had to apply with SNOTE in order to avoid bugs. And this is very useful, becasue I know exactly how many OSS Notes and which ones I had to apply and when (although I won´t transport it anywhere).
    Hope this helps
    Antonio

  • SAPUSER is locked in ECC 6.0 IDES SYSTEM

    Hi Everyone,
    I installed ECC 6.0 IDES SYSTEM, but the username SAPUSER is locked, I tried with various passwords but was not successfull. Is there any other way I can logon into it with this username or any other super username. Please help.
    thanks,
    Prashant.

    Hi techno guys,
    I have deleted the usr02 from sql table, and managed to logged in by Sap* and Password pass,
    But when I try to do something I am getting a sql error message that I do not have access or something like that,
    From SU01 also I couldnt create a username or unlock because same error page is coming..
    plz tell me do i need to do something after deleting that usr02 row from the table?
    plz advice me .. thanks

  • Creating Client 800 For ECC 6.0

    Hi,
    I have installed ECC 6.0 IDES in my PC,i able use 001 client with DDIC user name but iam unable to open 800 client.
    Can you please tell me how to create client 800 in ECC.
    Thanks in Advance,
    Regards,
    Balu.

    Hi
    As you said client 800 is already created in defult
    Tcode SCC4 check whether you have 800 client entry there,if you have then try to login with to 800 with sap/pass if it doesn't work then you need to delete sap and so that it will be recreated and you can login with sap*/pass
    Login to the SQL prompt and execute the following command.
    sqlplus"/as sysdba"
    sql>delete from sapsr3.usr02 where mandt='800' and BNAME="SAP*";
    where,
    SAPSR3 is the schema.
    mandt is the client
    Bname is the user name
    You also need to check parameter login/no_automatic_user_sapstar is set to 0 so you can logon as SAP* password pass,you can find this parameter at /usr/sap/SID/SYS/profiles in Default profile or Instance profile
    als chek the below links
    http://www.sap-img.com/basis/changing-the-default-password-for-sap-user.htm
    http://www.sap-basis-abap.com/bc/forgot-password-for-user-id-sap-in-client-000.htm
    http://help.sap.com/saphelp_45b/helpdata/en/52/671792439b11d1896f0000e8322d00/content.htm
    Regards
    Uday

  • Field for ECC 6.0 IDES

    Hi All,
    I would like to download ECC 6.0 IDES (ERP) for Oracle and SQL Server for Window. Which file does I need to download from Market Place?
    Thank.

    Hi Dusit,
    Follow this path.
    http://service.sap.com/swdc --->SAP Software Distribution Center ---> Downloads -->Installations and Upgrades -->My Company's Application Components >SAP ERP> SAP ERP 2005 -->IDES-Version --> Windows --- SQL server.
    Under this download the revelent media list as described in the installation guide.
    You would need the following
    Installation Master CD
    Java component CDs
    Export CDs
    Kernel CD
    Language CD
    Please go through the installation guide before downloading the software to check the correct media list.
    You need OSS ID for download.
    Reward if helpfull.
    Regards,
    Imran
    Edited by: Imran Khan on Feb 20, 2008 8:57 AM

  • Client Settings for Device collections Vs Client Settings for User collections

    I noticed there are "Client Settings" set for each User and Group in SCCM. I want all my "Client Settings" configured by Device Collections not User Collections, what can I do? Can someone explain the difference between those?
    Thanks
    James A+, Network+, MCP

    One is for user settings on a client and the other is for device settings on a client. As you can imagine user settings can only be deployed to user collections and device settings can only be deployed to device collections.
    For more information about the user and device settings see:
    https://technet.microsoft.com/en-us/library/gg682067.aspx?f=255&MSPPError=-2147217396
    My Blog: http://www.petervanderwoude.nl/
    Follow me on twitter: pvanderwoude

  • 2 clients of one ECC as a source system for BW

    Hi Gurus,
    we are asked by a customer to set up a new BW system, which will have 2 source systems, clients 300 and 400 of the same ECC. One client is ment for support team work  and the other for project team. I understand that the dataflow is partly different (e.g transfer rules and datasources are source system dependent), but most of the dataflow (extractors, customer exits in ECC, infosources, update rules, cubes, etc) are the same.  I am referring to 3.X dataflow as that is what we have mostly in the system, but we are on BI 7.0 already.
    Do you see any advantages/disadvantages of this approach?
    There are certainly some rules which have to be kept by such an approach (e.g. changing transfer rules for both source systems). What do you suggest, which rules should be kept? Would you do it differently? How?
    Thank you for your valuable inpt,
    Michal

    Ahoj Michal,
    your approach sounds feasible. You are already running BW in similar setup?
    Yes you need to check and modify all your specific settings according data split from 2 clients: e.g. routines in InfoSources, Update Rules etc...
    If I would do this differently? It depends on what purpose the data has in such a BW.
    - Do they really need to analyze data from both clients?
    - How the data model is setup? Do you have different data InfoProviders per client?
    I would consider this for approach....
    Vela stastia
    m./

  • NWBC for ECC 6 EHP6 IDES

    Hi Experts,
    I have installed IDES ECC 6 EHP6, to learn MDG, do i have to install NWBC separately or to activate from ERP? Please guide me
    Thanks & Regards
    Arunprasad N

    Did you activate the NWBC service? Check in transaction SICF.
    Also, please make sure to review the NWBC installation & configuration guides. They are available on help.sap.com. Here is one: SAP NetWeaver Business Client - SAP Library

  • What client settings for BIOS or MEBx do I need preconfigure for Out Of Band Management in SCCM 2012?

    Hi,
    On the Client:
    What BIOS or MEBx setting do I need preconfigure for Out Of Band Management in SCCM 2012?  
    Or can I remotly configure BIOS or MEBx settings from SCCM 2012 or Intel SCS?
    /SaiTech

    Thanks,
    Now I see, with Intel SCS add-on for SCCM 2012 it will be the most simple solution. Even better than to have Intel scs standalone, that was an complex setup on dhcp and so on...
    Just one thing more, When you configure AD for AMT you have to set a OU. but if you have computers in two ou, I cant see how I can configure that?
    /SaiTech

  • BIOS settings for 1 SATA + 3 IDE devices

    Hi,
    I'm a newbie to PC assembly so please pardon my ignorance.
    I am trying to install 1 SATA harddisk + 2 IDE harddisk and a DVD Writer on my MSI 865PE NEO2-PLS.  I have tried playing around with the BIOS but this does not seems to work. Can anyone advise on the possibility and the BIOS settings?
    Thanks.
    P4 3.0C  HT enabled
    PC 3200 TwinMos DDR400
    MSI 865PE NEO2-PLS
    MSI Radeon 9200SE 128MB
    Maxtor 120GB @ SATA-1 no RAID
    Seagate 40GB 7200rpm IDE
    IBM 10GB 7200rpm IDE
    LG 4160B 16x DvD Rewriter IDE

    Until you get Windows installed, only hook up the drive you plan on running windows on.
    Since you have 3 PATA devices you have to use Native mode.  The Native settings given by NovJoe are for booting from a PATA drive. If you decided to use the SATA drive, change SATA only to PATA only and make sure both PATA Keep Enabled and SATA Keep Enabled are set to Yes

  • Mail client settings for Sony Z2 tablet

    Tried to use standard mail client. However incoming mails are ok and are being downloaded. As for outgoing mails...here there is no synchronization with other devices, if You send mail there, it will appear in outgoing folder, if some message is sent from other device, it doesn't appear in this standard client application. The problem is only with the outgoing folder.How to fix?
    Thanks

    Hi pilotbroth,
    Welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
    Are you running a POP3 account? as POP3 only really shows a copy of what is in the inbox, outgoing would only show if say you used Exchange or IMAP4 based accounts.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Schema owner for ECC 5.0 IDES

    Hi,
    When I am trying to start ECC 5.0, the work processes are dying below is the error.
    OS: Windows, DB: Oracle.
    Now I'm connected to ORACLE
    C  *** ERROR => ORA-1403 when accessing table SAPUSER
    [dbsloci.c    10114]
    C  Disconnecting from connection 0 ...
    C  Closing user session (con_hdl=0,svchp=0493EFF4,usrhp=07FC1E64)
    C  Now I'm disconnected from ORACLE
    C  Try to connect with default password
    C  Connecting as SAPR3/<pwd>@CC5 on connection 0 ...
    C  Starting user session (con_hdl=0,svchp=0493EFF4,srvhp=07FB9234,usrhp=07FC1E64)
    C  *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1017
    [dboci.c      3721]
    C  *** ERROR => CONNECT failed with sql error '1017'
    [dbsloci.c    9750]
    B  ***LOG BY2=> sql error 1017   performing CON [dbsh#1 @ 1200] [dbsh    1200 ]
    B  ***LOG BY0=> ORA-01017: invalid username/password; logon denied [dbsh#1 @ 1200] [dbsh    1200 ]
    B  ***LOG BY2=> sql error 1017   performing CON [dblink#1 @ 419] [dblink  0419 ]
    B  ***LOG BY0=> ORA-01017: invalid username/password; logon denied [dblink#1 @ 419] [dblink  0419 ]
    M  ***LOG R19=> tskh_init, db_connect ( DB-Connect 000256) [thxxhead.c   1270]
    M  in_ThErrHandle: 1
    M  *** ERROR => tskh_init: db_connect (step 1, th_errno 13, action 3, level 1) [thxxhead.c   9377]
    Based on these errors I have looked at Notes: 400241, 50088.
    The problem is, even though schema owner is listed as SAPSID, why is SAPR3 being used to connect to Oracle.
    I have tried creating the users using note 50088, but to no avail.
    I have tried creating the users with schema owner as SAPSID. Above is the error message that I get.
    When trying to create the users with owner as SAPR3, I get the below error,
    ERROR at line 1:
    ORA-00959: tablespace 'PSAPUSER1D' does not exist
    ORA-06512: at line 114
    Regards,
    Vishi

    Hi,
    I have tried suggestions from you all of you, Thank you.
    However the problem still persists. I am quite unable to figure out, why it is showing SAPR3 in wp trace.
    Below are the error details from dev_w0 log, trans.log
    dev_w0:
    Logon as OPS$-user to get SAPR3's password
    C  Connecting as /@CC5 on connection 0 ...
    C  Attaching to DB Server CC5 (con_hdl=0,svchp=0493EFF4,svrhp=07FB9234)
    C  Starting user session (con_hdl=0,svchp=0493EFF4,srvhp=07FB9234,usrhp=07FC1E64)
    C  Now I'm connected to ORACLE
    C  *** ERROR => ORA-1403 when accessing table SAPUSER
    [dbsloci.c    10114]
    C  Disconnecting from connection 0 ...
    C  Closing user session (con_hdl=0,svchp=0493EFF4,usrhp=07FC1E64)
    C  Now I'm disconnected from ORACLE
    C  Try to connect with default password
    C  Connecting as SAPR3/<pwd>@CC5 on connection 0 ...
    C  Starting user session (con_hdl=0,svchp=0493EFF4,srvhp=07FB9234,usrhp=07FC1E64)
    C  *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1017
    [dboci.c      3721]
    C  *** ERROR => CONNECT failed with sql error '1017'
    [dbsloci.c    9750]
    B  ***LOG BY2=> sql error 1017   performing CON [dbsh#1 @ 1200] [dbsh    1200 ]
    B  ***LOG BY0=> ORA-01017: invalid username/password; logon denied [dbsh#1 @ 1200] [dbsh    1200 ]
    B  ***LOG BY2=> sql error 1017   performing CON [dblink#1 @ 419] [dblink  0419 ]
    B  ***LOG BY0=> ORA-01017: invalid username/password; logon denied [dblink#1 @ 419] [dblink  0419 ]
    M  ***LOG R19=> tskh_init, db_connect ( DB-Connect 000256) [thxxhead.c   1270]
    M  in_ThErrHandle: 1
    Trans.log"
    4 ETW000  [dev trc     ,00000]  Thu Nov 24 23:48:32 2011                           80178  0.132260
    4 ETW000  [dev trc     ,00000]  Assigning server context 02C0982C to service context 02C08C24
    4 ETW000                                                                              57  0.132317
    4 ETW000  [dev trc     ,00000]  Allocating user session handle                        47  0.132364
    4 ETW000  [dev trc     ,00000]  Starting user session (con_hdl=0,svchp=02C08C24,srvhp=02C0982C,usrhp=02C123F4)
    4 ETW000                                                                             165  0.132529
    4 ETW000  [dboci.c     ,00000]  *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1017
    4 ETW000                                                                            6620  0.139149
    4 ETW000  [dbsloci.    ,00000]  *** ERROR => CONNECT failed with sql error '1017'
    4 ETW000                                                                              31  0.139180
    4 ETW000  [dev trc     ,00000]  Try to connect with default password                  73  0.139253
    4 ETW000  [dev trc     ,00000]  Connecting as SAPCC5/<pwd>@CC5 on connection 0 ...
    4 ETW000                                                                              27  0.139280
    4 ETW000  [dev trc     ,00000]  Assigning username to user session 02C123F4           19  0.139299
    4 ETW000  [dev trc     ,00000]  Assigning password to user session 02C123F4           28  0.139327
    4 ETW000  [dev trc     ,00000]  Starting user session (con_hdl=0,svchp=02C08C24,srvhp=02C0982C,usrhp=02C123F4)
    4 ETW000                                                                              31  0.139358
    4 ETW000  [dboci.c     ,00000]  *** ERROR => OCI-call 'OCISessionBegin' failed: rc = 1017
    4 ETW000                                                                            7326  0.146684
    4 ETW000  [dbsloci.    ,00000]  *** ERROR => CONNECT failed with sql error '1017'
    4 ETW000                                                                              31  0.146715
    4 ETW000  [dblink      ,00419]  ***LOG BY2=>sql error 1017   performing CON [dblink#1 @ 419]
    4 ETW000                                                                             141  0.146856
    4 ETW000  [dblink      ,00419]  ***LOG BY0=>ORA-01017: invalid username/password; logon denied [dblink#1 @ 419]
    4 ETW000                                                                              27  0.146883
    2EETW169 no connect possible: "DBMS = ORACLE                           --- dbs_ora_tnsname = 'CC5'"
    Should I go back looking at Note: 400241.
    Regards,
    Vishnu

  • To Monitor inbound and outbound messages for ECC 6.0 business system

    Hi Guys,
    I am working on ABAP proxy. I want to monitor the flow of Inbound and Outbound messages for my Business system (ECC 6.0).
    XI server is on a different system.
    I understand that SXMB_MONI is used for tracking XML messages. What kind of tracking can we do by this transaction in our Business system and the XI system?
    And how do I know whether the outbound XML message sent is lying in the Sending Business system or in the XI system?
    When I am testing my interface, there is a fault message generated. How do I know whether the fault message is being sent to XI?
    Thanks,
    James.

    James,
    Go to SXMB_MONI in your sending system.
    Here you will find a message ID fro your Message.
    Go to XI, --> SXMB_MONI -->Monitor For Processed XML messages --> Advanced Selection Crieteria and use the Message ID here to see if the Message has hit XI or not.
    Likeiwse it can be traced in the target system as well.
    The basic point,  The messages will have same Message Id on your R3 and on XI.
    Regards
    Bhavesh

  • How do "Auto-detect proxy settings for this network" and "Use system proxy settings" work behind the scenes?

    How can I see what the proxy firefox actually uses when I check either of these two options?
    Does it take it from Internet Explorer?
    Are they stored somewhere in the registry?

    Hi conectionist,
    This is taken if there is a proxy set up in your network settings on your OS. If you would like to test there may be an add on:
    *[https://addons.mozilla.org/en-US/firefox/addon/smart-ip-connection-info/?src=search]
    Please feel free to search to find a better one if necessary.

Maybe you are looking for

  • How to filter a get-adcomputer command using a text/csv file and output to a CSV

    OK, so I'm in the process of trying to get a Windows 7 refresh completed for a large client... I had the bright idea to use AD to find what computers are listed as XP, and determine our progress using that.  Well, I run get-adcomputer, and it returns

  • Disabling the MBP's ability to receive signals from remote control?

    I own an AppleTV, my roomate uses a Macbook and I have the Macbook Pro, and they all use the same remote control and signal. Anytime we use the remote for the AppleTV it sends our notebooks into Front Row. Is there anyway to disable the mac's ability

  • System preferences won't open

    I'm getting an error message every time I try to open system preferences, from the dock or through the folders. Software updates were downloaded last night and that's when the problem began. I have no idea how to fix this and am trying to save myself

  • How to view develop adjustment photos on LR3.2

    I noticed after adding adjustment on library view, it stamps a small icon on the right lower corner which is very helpul.  I have many photos and when I want to separately view the only adjusted photos, how do I do this? I am sure it is simple but be

  • Power switch doesn't work

    I am able to shut down my computer   FM2-A85XA-G65 MSI Motherboard but cannot restart using the computer power switch.  Have to open the case and press the switch on the MB (has a green lite on it) and then the computer starts and runs fine.  I must