SLI issue with N660Ti-2GD5/OC (new bios request)
Hi,
It started all with issue regarding SLI performance under F1 2012 game.
When SLI is enable I can't get more then 30FPS average. I try changing SLI rendering mode with no luck... nothing change.
I noticed that when SLI is enable I only get 25% GPU usage per card and my 3D GPU clock is not reaching MSI declare speed.
When SLI disable everything is working normally. I get 58FPS average, 95-100% GPU usage and my 3D GPU clock is working at MSI declare speed (I think it is 1020MHz).
So I suppose that this is negative SLI scaling...
I was doing some testing and SLI (I have enable show SLI visual indicator) doesn't work properly in any game that I have install on my pc (F1 2010, BF3, BC2 and NFS Shift).
I have same issue in all games: low gpu usage, 3d clocks doesn't reach declare speed (with three, two or only one monitor connected).
So next I installed Heaven Benchmark 4.0 and started testing and for some unexplainable reason SLI is working normally.
After that I started games again but no GO ... again in games SLI is not working correctly.
I was thinking that maybe my SLI profile are not working right... so I decided to change driver, I try 320.14 and 314.22 nothing change - SLI not working correctly.
Then I download nvida inspector and try to define SLI profile for those games - nothing change - SLI still not working correctly.
I even try to disable first card through device manager so I can test the second card and vice verse, separately both cards are working normally.
So only in Haven benchmark 4.0 SLI is working correctly I have GPU usage of 95% and declare speed for 3D clocks.
I have Win8x64 (fresh install), nothing overclocked, I enable Prefer maximum performance in nVidia drivers and disable V-sync. CPU Fx-8350, Asus sabertooth fx990 rev.2 (latest bios), 1200W chieftec power supply and everything is properly connected.
Is there a new bios release for my cards? Maybe this could solve my issue? And who can supply me with new bios?
Sorry for long post but I am really desperate... any thoughts or maybe solution.
Regards
Well my monitor doesn't support more then 1680x1050, but still if this is the case I think that ATI is the way to go... my humble opinion.
So now I can sell my second card because SLI doesn't work... I am totally depressed.
Ok but can someone please,please supply me with new firmware for the cards? I just one to try it just to know that I tried everything before I go and sell those cards and go for ATI solution.
Regards
Similar Messages
-
Issues with Oracle in a new location.
Hello -
I recently had to change the computer name of a Windows 2003 SP2 test server. Among other software installed was Oracle 10g r2. There were issues with Oracle in its new location where it was trying to reference the old computer name.
I assumed that all I would have to do to correct the issue was to search all of Oracle’s .ORA files and replace the old server name with the new one. (Plus, of course, changing the Windows Host file entry).
But I’m finding that Oracle on Windows apparently has many other references to the original computer name. For example, there are subdirectories in the Oracle Home directory tree structure where the directories themselves contain the old computer name. (I’ve attached a screenshot of a file search off the Oracle directory tree for “BRI2KSRV” which is the test server’s old name. “Bri2ksrv.jax.fnfis.com” was the server’s old fully qualified name. ORCL is/was the default instance name).
For example, these directories were found:
..\oracle\product\10.2.0\db_1\bri2ksrv.jax.fnfis.com_orcl
..\oracle\product\10.2.0\db_1\log\bri2ksrv
..\oracle\product\10.2.0\db_1\oc4j\j2ee\OC4J_DBConsole_bri2ksrv.jax.fnfis.com_orcl
What are the recommended steps when changing the Windows computer name (and thus the fully qualified network references) on a Windows 2003 Server which has a functioning Oracle 10g R2 instance?
Thanks!These directory you mentioned are EM control directory. You need to reconfigure your EM with new server name.
If you are using server name instead of IP address in listener.ora and tnsnames.ora you need to change these as well. -
MSI 975X Power Up Edition V2.1 Issue Beside Overclocking After Flash New Bios
Hi all,
I hope I can get a lot of help here. I'm having a few issues with this board. I cannot find any thread that discuss other issue beside overclocking after you flash a new bios. Here are my problem:
1. I installed fresh WindowsXP with SP2. Windows cannot detect new usb device eventhough WindowsXP recognized the usb controller. If I plugin any usb device, windows does not detect a new device. I try to stick a USB flash and I can see the light for a few seconds but Windows cannot detect it. Before I upgrade the bios to version 715 (beta), I used usb flash to upgraded it. Now, the bios is not even boot from usb flash.
2. Other things that concern me, the southbridge chipset is really really hot. If you touch it long enough, it will burn you.
3. I cannot figure it out the front audio from manual book (JAUD1). Is any of you know where the mic needs to go?
ThanksI removed the Big Typhoon from the MB and I replace with stock fan. I want to make sure the back plate from Big Typhoon doesn't cause any problem. When I bootup the windows, I saw WindowsXP recognized the USB device but it disappeared again. I took the MB out from the case and test it without a case. It stills does not recognize the usb. Somebody mention bad PSU(Power Supply Unit) may cause a lot wierd problem. I changed PSU from RaidMax Vocalno 630W to Ultra X-Finity 500W. I don't have a lot of stuff that require power. Do you think the PSU cause this issue?
This is list of my comp:
MSI 975x Platinum PowerUp Edition V2.1
Conroe E6600 Retail
Seagate 300G SATAII
Maxtor 120G IDE 100
Asus 16X DVD-ROM
NEC 3550A DVD-RW
Ultra X-Finity 500W
120 mm Fan
80 mm Fan
Big Typhoon
FYI: USB Controller and USB 2 Controller are enabled in BIOS. -
Issue with reinstalling a brand new mac pro
I was recomended to reinstall the leopard since I had some issues with my new 27"
cinema display.( there is an update for the cinema display and my mac did not allow me to updat it so apple care person told me to reinstall the leopard.
After 15 minutes in gto the reinstalling the mac pro has stopped responding and i have a white background with apple logo in the center of the screen fro the last 2 hours.
Any recomindations until the apple care is back on the line.Make sure you have the display usb cable connected as some of the functionalities
are addressed through the usb cable. -
Issue with : Stateful BSP Applications: New State Management Option
Reference:weblog by Thomas Jung - /people/thomas.jung3/blog/2004/11/09/updated-stateful-bsp-applications-new-state-management-option
I see a comment by one user to send the complete code... I am not sure what else can be sent - try it out rather than getting spoon-fed. - getting offline - sorry...
I had two issues with this ITSM way of session handling.
First - if you are using an SP42 environment, check CL_BSP_RUNTIME=>ON_SESSION_CMD() to see if CANCEL is defined as an option. If not make sure that you use &sap-sessioncmd=CLOSE" instead of the &sap-sessioncmd=CANCEL" . If CANCEL is not defined , it will give you shortdumps...
Second - when I closed the window, the session was not terminated. I used onbeforeUnLoad="exitBSPApplication(); instead of onUnLoad="exitBSPApplication(); and it worked fine. Not sure if it has any other issues.
But now I am facing a new issue... all but one application is not ending... I have no clue on why this is happening.. I am still checking..
Thanks Thomas, you are the best, as always...Thanks for checking the code in your system.
After some investigation, I found the behavior as explained below.
If the actual url has any fields passed as parameters, e.g.. /default.htm?var1=a&var2=2 ...
- if I use CANCEL as the option, a shortdump is created and the session is not closed. if I use CLOSE, Session is terminated and no shortdump happens.
If the actual url does not have any parameters, e.g.. /default.htm ...
- CANCEL does the work, but CLOSE does not exit the session.
In my applications I used request->get_form_fields to see if there are any parameters, and if there are, then I use CLOSE as the option and else, I use CANCEL. So now, the session
management works beautifully...
There is a good chance that I am doing something wrong here too. -
New Bios Request For N560GTX-Ti TF II (Artifact and PC Hang when using firefox)
I encountered the problem 3 times for the past three days as I was forced to do a hard reset.
I am surfing flash videos on firefox and suddenly the screen go green, purple and red flickering 'dots and strips', the mouse cursor stay alive for a second, then it stops, i cant do anything except a hard reset.
Display driver : ForceWare 296.10
BIOS : 70.24.0A.00.00 (P1040-0050)
s/n: 602-V238-16SB1101057250
Device ID 1200
Sub vender ID 1462
Sub System ID 2382
880 MHz Core
1024MB GDDR5 4200MHz Memory
Win7 x64
my bios: http://www.mediafire.com/?bi5hu0as2ymr9th
Intel i7-2600
Asus P8P67 LE
2gb Kingston memory X 2
Cooler Master Extreme Power Plus 500W
can Svet get me the new bios?
thanks!Quote from: magicarshavin on 28-March-12, 06:15:26
After updating to the latest bios 201, the mouse movement feels sluggish, can i revert back using my backup bios GF114.bin (GpuZ) ?
Is it using the same command nvflash.exe -4 -5 -6 GF114.bin in USB boot dos will do?
Thanks.
Yes, that's right.
But the mouse movement feels sluggish is probably caused by something else rathar that vbios.
I suggest you to preinstall VGA drivers.
Remove current one 1st in Safe Mode with >>Driver Sweeper<< before install the new VGA drivers -
Hi,
I have the same problem (pink/purple/green flickering ) except that I am using Google Chrome viewing some videos from youtube. And the driver that I am using is version 295.73. I already tried 296.10 but I encountered TDR that's why I go back to 295.73.
GPU-Z screenshot of my VGA --->
My BIOS ---> http://www.mediafire.com/?qlcc2q4j1yqhepn
S/N: 602-V238-270B1109140158
OS : Windows 7 Ultimate x64
MBoard : ASUS P8Z68-V
RAM : 8GB G.Skill
PSU : Corsair HX 850
I already asked for help at nvidia forum and they said I ask for a new bios here. Thanks!Topic splited. next time don't hijack other people topics, open your own instead.
Dunno about this one, contact msi tech here: http://support.msi.com/ -
Windows 8 blank screen issue with N660Ti PE 2GD5/OC
Dear MSI support.
My current setup:
Motherboard: Asus P8Z77-I DELUXE
CPU: i5 3570K
RAM: 8GB G.Skill Sniper 1866 MHz - CL9
GPU: MSI GeForce GTX 660 Ti Power Edition (OC) (stock BIOS)
After running Windows 8 Professional (64-bit) on my computer with my iGPU (Intel HD 4000) I installed my new GPU (MSI Geforce 660 Ti PE). After my first boot with my new GPU, the BIOS info is displayed on the screen, then the Windows 8 logo and finally the screen goes blank. If I set my bios settings to use iGPU Windows boots normally again.
I've even tried a fresh install of Windows 8 with the same results. When the installation process completes the "Getting devices ready" text is displayed for a couple of minutes before the screen goes black again. I can log on to Windows 8 in Safe-Mode with the 660 but not in normal mode.
I've also tried to install Windows 7 (32-bit) which works fine with the 660. So it's sound's like a Windows 8 compatibility issue to me.
Any suggestions or tips are highly appreciated.
Thank you very much.
Bogganero.what PSU you use?
Display? how's connected to the VGA?
check also:
http://social.technet.microsoft.com/Forums/en-US/w8itproinstall/thread/f3846fb7-0db9-446d-bc8c-33d34ff47122/
http://www.eightforums.com/installation-setup/4505-screen-went-black-after-getting-devices-ready.html
http://www.neowin.net/forum/topic/1115183-installation-stuck-at-getting-devices-ready/ -
Finally got my sli rig here, but nothing seems to work as it should do :(
Here are my specs;
MSI K8N Diamond sli
2x MSI 6800GT
Corsair 1gig cl2
a64 3500+
psu - enermax 600W
Everything runs at stock speeds. The problem is, i got issues like THIS, thats why i cant take shots. All non-sli games run perfect. Cards have latest bios.
I have no idea what to do now. Is it the cards? The mobo?
Any suggestions? :(Your link provided the answers to your questions. There seems to be some fine-tuning left to do from nVidia. I had read a similar article a few weeks ago, and thus - I purchased the 6600GT PCI-E cards for my SLI system due to those discrepancies. I believe it is an inherent design problem with the higher-end 6800 cards, as described in the article.
In the meantime, see if enabling "Spread Spectrum" in your BIOS will help.
Other than that, I would suggest RMA'ing those 6800's in favor of a couple 6600GT's. -
Issue with af:commandMenuItem exiting new window...
Hi everybody!
Testers are reporting an issue that I have not yet successfully reproduced.
This app was produced in JDeveloper 10.1.3.3.0 using ADF BC/JSF.
The issue is very simply described. I am jsp-including an af:menuButtons component which has af:commandMenuItem's inside of it. One of these is a help button which has only the onclick event defined as follows:
window.open('../Help.html##{requestScope.currentPageFileName}', 'helpWin', 'width=1000,height=350,resizable=1,scrollbars=1').document.title = 'Application Help'
The tester complaint was that when they clicked on the commandMenuItem help link, then immediatley exited this help window, before it had finished rendering (presumably using the red X in the upper right corner, or alt-F4), the adf application would hang. No navigation could occur after that pre-mature exit.
Has anybody seen anything like this?
Thanks in advance for your time.Michael,
can you try a goLink to open the new window instead of the onClick event ? This way you avoid that your code conflicts with the internal framework JavaScript. In the past I recognized that JavaScript added to the on... events may conflict with the framework codes. The work around I found in this situations are
- use a goLink
- register the on... event dynamically during page load using document.getElementById()
I would try the goLink first because it does exactly what you want without having to hack in JavaScript
Frank -
Having issues with gotoURL and open new window
I am having trouble opening a new browser window with the gotoURL
script. This is the current FormCalc that I am using.
$host.gotoURL("http://www.google.com",1)
I am wondering if this is working as expected? My PDF does not open
into a new window in any browser or Adobe Reader. Is anybody aware of
this problem? I have hyperlinks on my form that I am trying to get to
open in a new window using FormCalc scripts.
Appreciate any help. I am trying find out if this is bug, or is working
as expected, or if there is another script to accomplish this?
Thanks,
RebeccaThere are lots of customer applications that are based on Windows RAC. And as mentioned above, it is very well supported by Oracle.
However, because of the security vulnerabilities of Windows, I've observed that most of the financial institutions and listed companies opt for unix based servers for all high profile applications and run only low to medium risk application on Windows.
Regarding maintanence issues, I guess it's going to be pretty much the same; there shall always be lots of bugs, lots of patches and updates just like an yother software; doesn't really matter if you are on Unix or Windows systems. As long as you purchase support, it's all good.
It's pretty much same concern regarding Grid Control on windows.
Cheers. -
MMy new iPhone 5 just blacked out and won't come on. Does anyone know if I will have an issue getting a new phone from Verizon.? I can't even call because I don't have a phone!
Ebony,
Let's see if we can't get this phone working for you! What exactly is happening with the device? Is the screen just out and you can hear that it will still ring, or is the phone completely dead? Please elaborate more on what you are experiencing.
SandyS_VZW
Follow us on Twitter @VZWSupport -
Issues with 'stuck' keys on new iMac (2011) with Aluminium KB
Hi All,
I've got a weird issue which I've seen on a few other forums... with no real fix. I've got a new 27" iMac (2011) and I have been using it happily for a few weeks. In the last two days, my keyboard has been going a little crazy.
Firstly I thought it funny that the 'option' key wouldn't work during bootup and later I discovered that once booted in OSX, i'd have 'sticky' keys or keys not registering when pressed.
When I reset the keyboard, everything works fine again.
Its becoming a problem as I cannot register an of the bootup options anymore and have reverted to using an old Remote to access my boot volume screen (holding the Menu button).
Has anyone seen this before and if so, what is the fix other than taking the keyboard back to the Mac store?
Thanks again,
ConHi Cabakroll,
Yeah, I've been doing regular updates (when available). I have actually figured out the issue... its a very weird fix mind you. I went back to see what changed the other day, when I first notice the issue. I recalled that I swapped out the batteries (the ones that came with it were running low for some reason), with rechargables.
Since then, the keyboard has been going crazy. I swapped the rechargables with normal batteries and bingo, problem fixed. :S
Thanks for getting back to me though.
Hopefully this helps others too. -
Potential Driver Issues with OS Install on New Hard Drive?
I want to upgrade my laptop's hardrive, but my laptop did not come with recovery discs. I did purchase a full copy of Windows 7 Professional, but I have been saving it...for when all else fails, I suppose. Whether I am able to reinstall Win 7 Home or whether I have to install Win 7 Pro, how can I be sure to reinstall all the necessary HP drivers (e.g. trackpad, cool sense, beats audio, etc.) for my machine? Is it best to download the drivers prior to installing the new hard drive and have them ready on a flash drive; or is there an easier method? Thanks.
This question was solved.
View Solution.Yes that is a very good question.
It's very much advised you do a HDD error check, hard drive test from BIOS and SFC scan lastly.
You can then undergo a disk cleanup and disk defragmentation of the HDD & then proceed with backing up or cloning tools.
I do back up regularly into my 2TB external drive using Macrium reflect, AOMEI back upper and also have all my latest drivers downloaded and copied to another USB along with another bootable USB with Windows OS ISO.
Note: I've already created my recovery media after I setup the laptop first time for additional safety.
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP** -
Focusrite Scarlett 2i2 clapping and crackling issues with Logic Pro x new iMac 27"
Hi, I have just purchased a brand new iMac and downloaded Logic Pro x, I also purchased the Focusrite Scarlett 2i2 interface. I have downloaded the drivers from the focusrite website and everything is set up, when I plug in guitar or mic I get really bad clapping and crackling to the point where the sound cuts out altogether. I have changed buffer size and sample rates and everything else I can think of but nothing seems to fix the problem. I also deleted the 2i2 drivers and logic and reinstalled them both but still have the same issue, when I record using the iMac built in mic everything is fine so it's deffinately something to do with the interface. I am waiting to hear back from Focusrite tech help. Does anyone else have this problem? Any help would be appreciated.
I'm having a similar issue which might indicate that the problem is not your interface.
Yesterday I migrated all my stuff from my 2009 iMac to a brand new iMac 27", and when I did a quick test to play back some old projects in Logic there was loads of annoying clicks and pops. My interface is a Roland Octa-Capture.
I also noticed some weird CPU spikes from time to time, which I never had on my older, much less powerful iMac...
Maybe you are looking for
-
Install problem in step "Prepare to Configure AS Java"
This step performs extracts to /usr/sap/trans. During the night directory reached 100%. I added more space and replied OK to retry. I receive the following error message: Error occurred while trying to copy software archives to /usr/sap/trans/EPS/in/
-
New iPod Touch & TV connection
Hi all, I just got a new iPod Touch. It was my understanding that its precedesor had an Video Out port so you can connect it to a TV and watch videos. If this incorrect on my part I apologize. I tried to connect the new iPod Touch to the TV using a s
-
"Dynamic Declaration/Variable"
Hi, first sorry for my bad english :) I have a Problem with Forms Builder 6 I want to know if it possible to set dynamic declarations inside a loop loop_i := 1; WHILE loop_i < 10 LOOP go_item('GERAET' || to_char(loop_i) || '.Beginn'); --Geraet1.Begin
-
i dont know where to find what current os i am running..
-
Is anyone else having issues due to the updated Windows 8.1? I have a panasonic digital video mini casset camera that worked fine using a USB cable to upload video. Now the program will not see the camera as a source. Using a firewire is not an op