SLM 2048 GOING dead slow very often

Hi,
We have bought 1 of SLM2048 for our office to upgrade two old switches to one 1GB network. I wonder what is the reason that eveery now and then the trafic slows down to about 10 to 20 kB/s and I need to reboot the switch to get it working again. it is going on in different intervals some times twice a week somtimes twice a day (as today) .
Does enybody have idea what causes it. Is it overheating or is it some firmware issue? It is realy anoing. And Im now getting blamed for spending £600 for the switch which does not do any good.
help please
Petr

Hello,
Have you considered contacting our support?  The home page has a link to our support group, see the right hand side of the page:
https://www.myciscocommunity.com/community/smallbizsupport
A few things you will be asked about:
1) have you upgraded to latest firmware and performed a reboot?
2) is this related to processor or traffic loads?
3) if processor, we will need to see the configs in order to see if anything is 'funky'.   Also some logging will help, syslog events.
4) if traffic loads, which ports are causing this?
5) In the middle of the 'slow down' which ports have their lights constantly on?
6) can you disconnect ports one at a time to find the culprit?
Just a few thoughts to help speed this up  ...
HTH,
Andrew Lissitz

Similar Messages

  • Whenever i open a youtube video, firefox goes really slow and often stop working. Any suggestions?

    I have installed the plugin extension, but still whenever a youtube video is on firefox is like drop dead.
    Stop working and lag awfully.

    There are some compatibility issues between the latest Flash player and some Firefox add-ons or settings. Could you see whether anything in this article helps: [[Flash 11.3 doesn't load video in Firefox]].
    You might also consider disabling the new protected mode in Flash 11.3. See this support article from Adobe under the heading "Last Resort": [http://forums.adobe.com/message/4468493 Adobe Forums: How do I troubleshoot Flash Player's protected mode for Firefox?]

  • My computer goes dead slow when runnig itunes

    I have a dual core 3 ghz procesor and 4 gb of ram with 64 bit windows 7 runing plz help me my 60 percent procser is used by itunes how can i make it faster by comsuming les procesor

    Have you tried this article: http://support.apple.com/kb/TS4123

  • HT201412 After ios7, My iphone4 has gone dead twice in a time frame of around two months...even though its not happening very often but a two month Old phone going dead just after a New update is not acceptable.probably ios7 still has sum bugs dat need to

    After ios7, My iphone4 has gone dead twice in a time frame of around two months...even though its not happening very often but a two month Old phone going dead just after a New update is not acceptable.probably ios7 still has sum bugs dat need to be fixed...Can this bug expected to be fixed in the next update...

    Hi 1283ar.
    Unfortunately, iOS 7 is too hard to push for the iPhone 4 and therefore has a lot of effects turned off to try to get it to run as smoothly as possible.
    However, it becomes better and better with each update coming but it's hard to do anything about the hardware on an already released phones.
    If you still have trouble or think they are too hard. My tip is, if so, to restore your iPhone 4 and make a clean setup with no iCloud backup. But all your photos in a photostream so you can access it later.

  • My iphone 3g stays on the apple logo for about 4 minutes then flashes white and goes back to the apple screen, it repeats untill battery is flat,  every now and then im lucky enough to get it to turn on but not very often and then it freezes and repeats??

    hello my name is kirstie, i updated to firmware 4.2.1 .....my iphone 3g stays on the apple logo for about 4 minutes then flashes white and goes back to the apple screen, it repeats untill battery is flat,  every now and then im lucky enough to get it to turn on but not very often and then it freezes and repeats the same problem?? (if i turn the phone off my pressing the two buttons it wont keep rebooting, its only when i leave it after turning it on)
    I have reset the phone, full firmware restore, even downgraded back from firmware 4.2.1 to .3.1.3 official by using dfu mode and still doesnt fix.
    (i correctly got out of dfu mode after the downgrade)
    i can enter dfu mode and recovery, and update through itunes with no problem, but it doesnt fix the problem,
    i have searched and found no answer to this problem, every option availible to try that i know of i have tried and failed. i dont care about preserving my content i just want a fix. i have a good understanding how to operate software on a computer and shouldnt be too confused by any advice given, so plz even if the answer is very complex i wish to try anything, please help me to get my iphone working.

    Anyone have any suggestions? or is everyone else just as clueless as me !

  • My MacBook Pro gets very slow while doing  work like watching movies and using net .. video gets lag very often

    My MacBook Pro gets very slow while doing  work like watching movies and using net .. video gets lag very often and while surffing on net it gets very slow ...

    First, back up all data immediately, as your boot drive might be failing.
    There are a few other possible causes of generalized slow performance that you can rule out easily.
    Reset the System Management Controller.
    If you have many image or video files on the Desktop with preview icons, move them to another folder.
    If applicable, uncheck all boxes in the iCloud preference pane.
    Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
    Check your keychains in Keychain Access for excessively duplicated items.
    Boot into Recovery mode, launch Disk Utility, and run Repair Disk.
    Otherwise, take the steps below when you notice the problem.
    Step 1
    Launch the Activity Monitor application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Activity Monitor in the icon grid.
    Select the CPU tab of the Activity Monitor window.
    Select All Processes from the menu in the toolbar, if not already selected.
    Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
    Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
    Next, select the Disk Activity tab. Post the approximate values shown for Reads in/sec and Writes out/sec (not Reads in and Writes out.)
    Step 2
    If you have more than one user account, you must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
    When posting a log extract, be selective. Don't post more than is requested.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

  • After ios7 update my iphone is like android os dead slow processing , too fast battery drain,calling process is too low where is apple brand going my friends 11 members using iphone all are got this problem one thing fans like me y they spoil his name ??

    after ios7 update my iphone 4 is like android os dead slow processing , too fast battery drain,calling process is too low where is apple brand going my friends 11 members using iphone all are got this problem one thing apple have unique and unique fans like me why they spoil their name like this update iam too disappointed iam not say for oppose apple iam say for feedback to grow apple in world because i love apple more please solve it
                       by real customers
    iPhone 4, iOS 7, iam apple suporter

    please help me after ios7 update my phone is tooo slowww i want my old iphone                         

  • Battery is going dead very fast

    i have HP Pavilion g6 model notebook, a bit more than 2 years old. untill last month my battery health status was about 72% good (means only 28% dead). but in last few days the battery is going dead at a very fast rate about 1% every 2 days. the status is now 48% in just a month fallen from 72%. i don't understand the reason behind this. neither my laptop is getting overheated nor there is any other hardware problem. i work on my notebook for about 6 hours daily as usual. i don't even run heavy softwars on battery power, i switch it to AC power while working with heavy softwares or games. 
    plz help me out with this...

    Hi,
    Please use the following test:
        http://h10025.www1.hp.com/ewfrf/wc/document?cc=au&lc=en&docname=c00821536
    You may need to replace battery after 500 to 700 charging cycles.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Sdlc interface down very often

    Hello,
    In my customer site, SDLC device connect to 2600. IOS version is 12.0.7T. Then access AS400 through DLSW function. We showed log and found the connected interface down very often. show log as below.
    We checked AS400 log and didn't find the SDLC device inactive ever. And we check SDLC device, the device work well, user didn't find any problem??
    We don't know why always log of message showed the interface down.
    Anyone can help me??
    .Jun 23 08:29:56 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down
    .Jun 23 08:29:57 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
    .Jun 23 08:30:01 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up
    .Jun 23 08:30:02 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
    .Jun 23 08:33:06 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down
    .Jun 23 08:33:07 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
    .Jun 23 08:33:11 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up
    .Jun 23 08:33:12 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
    .Jun 23 08:36:16 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down
    .Jun 23 08:36:17 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
    .Jun 23 08:36:21 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up
    .Jun 23 08:36:22 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
    .Jun 23 08:39:25 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down
    .Jun 23 08:39:26 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
    .Jun 23 08:39:30 Taiwan: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up
    .Jun 23 08:39:31 Taiwan: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
    JSB025a#sh inter se 1/0
    Serial1/0 is up, line protocol is up
    Hardware is CD2430 in sync mode
    Description: connect to SNA pu2.1
    MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation SDLC, loopback not set
    Half-duplex enabled.
    cts-delay 0 milliseconds
    dcd-txstart-delay 100 milliseconds
    dcd-drop-delay 100 milliseconds
    transmit-delay 0 milliseconds
    Errors - 0 half duplex violation
    Router link station role: PRIMARY (DCE)
    Router link station metrics:
    slow-poll 10 seconds
    T1 (reply time out) 3000 milliseconds
    N1 (max frame size) 12016 bits
    N2 (retry count) 20
    poll-pause-timer 10 milliseconds
    poll-limit-value 1
    k (windowsize) 7
    modulo 8
    sdlc vmac: 4000.2625.01--
    sdlc addr 01 state is CONNECT (xid-poll)
    cls_state is CLS_IN_SESSION
    VS 5, VR 0, Remote VR 5, Current retransmit count 0
    Hold queue: 0/200 IFRAMEs 116636/58170
    TESTs 0/0 XIDs 40235/14460, DMs 6784/6736 FRMRs 0/0
    RNRs 7/0 SNRMs 9757/0 DISC/RDs 9733/0 REJs 0/0
    Poll: clear, Poll count: 0, ready for poll, chain: 01/01
    Last input 00:00:00, output 00:00:00, output hang never
    Last clearing of "show interface" counters 9w3d
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 0 bits/sec, 50 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    156063821 packets input, 318338246 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    11 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 11 abort
    155708948 packets output, 337016303 bytes, 0 underruns
    0 output errors, 0 collisions, 43092 interface resets
    0 output buffer failures, 0 output buffers swapped out
    106807 carrier transitions
    DCD=up DSR=up DTR=up RTS=down CTS=down

    Hi,
    I believe that your line keeps bouncing due to Data
    Carrier Detect(DCD) going down. I didn't see a copy
    of the interface config but do you have the following
    command under your interface?
    half-duplex controlled-carrier
    This in conjunction with the dcd-txstart-delay and
    dcd-drop-delay settings will cause the DCE to drop
    DCD frequently.
    These are for very specialized environments which
    probably are not what you have.
    What is your environment, with respect to the
    connection to the AS/400? Is it just a Cisco DCE
    cable connected to an AS/400 cable? Or are there
    other cables/switches/modems involved?
    If you just have the Cisco DCE cable connected to
    the AS/400's cable then you do not need that command.
    Otherwise, it is possible you have a cable or
    physical interface problem.
    Please include your interface's config if this
    information wasn't enough to resolve the problem.
    Thanks and regards,
    Ed Mazurek

  • Safari keeps shutting down on my iPad very often. Does anybody have information about this problem? Thanks

    Safari as well as other apps like USA Today and BBC, shut down very often in my iPad. I have experienced this problem before, but now it happens all the time. I can hardly have a full web surfing session without this annoying interruption.
    When I restart the app I usually get to the page I was reading so I don't understand what's going on.
    Does anybody have information about this issue? Any suggestions or solutions?
    Thanks

    Rick --
    Safari has never needed Rosetta to run.
    It fact, it makes it run agonizingly slow --
    or could cause it to crash. That's probably your problem.
    I you really need Rosetta to work with this app, your Math program is using really old technology,
    and was built to run on OS9, or even OS8.
    Example: Many of us used to use PageMaker for designing brochures.
    When Macs went to 10.2.8 or so, PageMaker couldn't run, so Apple included
    a faux environment on newer Macs, where old apps & games would run.
    That was about 5 or more years ago. The need for Rosetta is very very rare,
    as most all apps used today would be newer than 5 years old.
    Like Mulder said, a crash report might help identify the exact culprit.
    EDIT: Have you tried turning Rosetta off???? Just to test it??
    Message was edited by: ~Bee
    Message was edited by: ~Bee

  • Satellite L310-D4010: OS has become dead slow while using the CD/DVD drive

    Dear all,
    I has bought Toshiba Satellite L310-D4010 at chennai, India.
    It has 2GB RAM and 1.83 GHz Intel Core2 Duo Processor.
    But my system has become *dead slow* while i am using the optical drive i.e., when i am writing a disk and copying the content form the disk.
    I was not able to open any application while i am using the DVD drive.
    Please guide me to resolve this problem.
    Thanking you.

    For me it is also logic that notebook performance goes down when I copy a lot of data. To be honest when I use some burning application to save data on CD or DVD I leave it running till the end and avoid usage of other applications while burning procedure is active. All I do at the same time is surfing in Internet.
    I cannot imagine you are not able to start some applications. Maybe notebook needs some more time to start application but it must work.
    At the end I must say that 2 GB RAM for Vista notebook is for me really the minimum and if possible I recommend you to upgrade RAM if possible. This notebook model is not known to me and max RAM for this model is not known to me but I presume the 4 GB should not be the problem.

  • I am running Mac OS X Lion on a brand new Mini.  Every now and then, my keyboard goes "dead."  The mouse still works but can't type.  If I restart, everything is fine again.  Is there anything that will fix this problem?

    I am running Mac OS X Lion on a brand new Mini.  Every now and then, my keyboard goes "dead."  The mouse still works but I can't type.  If I restart, everything is fine again.  Is there anything that will fix this problem?
    Also, I am trying to connect my Mini from the mini-Displayport to the Displayport of my Dell U2410 monitor.  The image is very grainy,even though it is set to the correct resolution: 1920 X 1200 at 60Hz.  If I use HDMI to VGA input, the image is much clearer.  Is there a way to get the Displayport to work?

    I'm having exactly the same keyboard issue.  Certainly nothing has ever enhanced my concentration while coding like suddenly becoming unable to type.
    I'm seeing a great many devicemgr and rake errors in my system log.  I don't know if they're related.  How 'bout you?
    If you're unfamiliar with the system log…
    Open /Applications/Utilities/Console.
    If necessary, choose View > Show Log List.
    system.log is at the top of the FILES section.
    Try searching it for hot words like DEBUG, FATAL, and aborted.
    I've found some discussions that would tend to indicate my errors are postGres related – I'm running OS X server.
    -Bryan

  • Garageband 10 going SOOO slow...help please.

    Hello everyone,
    I just downloaded the newest version of Garageband (v.10) and now I've noticed that it is going extremely slow. This is a brand new iMac I'm running it on. My specs are as folllows:
    27 inch model
    3.2 GHz quad-core Intel Core i5
    8GB of 1600MHz DDR3 SDRAM
    1TB HD
    I really feel like my computer should be running this without a problem. Why is it lagging so hard?
    I don't have any other programs running (besides an instance of Safari).
    The reason I'm worried is because I have a project coming up in which I will need to crank out a LOT of music in a very short period of time. I need this thing to be operating at top capacity.
    Is there something I'm missing?
    Is it possible to revert back to the older version of Garageband that I know worked just fine?
    PLEASE HELP, I'm in trouble if I can't fix this.     

    I don't have any other programs running (besides an instance of Safari)
    Safari can be a memory hog - if in doubt, quit Safari, before working with GarageBand.
    Is it possible to revert back to the older version of Garageband that I know worked just fine?
    If you did not delete your older GarageBand version, when you upgraded, it will be still installed. The GarageBand installer will have moved it to a subfolder of Applications -look for a folder GarageBand 6.0.5 in Applications. You can use both GarageBand version in parallel, no problem.
    and now I've noticed that it is going extremely slow
    Try to narrow down the problem. Is this the same on all projects?
    Then check, if you have incompatible audio units installed. GarageBand 10.0 is not compatible with older Audio Units.  And if you are using audio interfaces, check, if there are updates for the drivers.
    See:  GarageBand for Mac (v10.0): Unexpected behavior with Audio Units plug-ins

  • MBP to MacPro Network Connection Deadly Slow

    I recently purchased an Intel MBP, and am connected to my home network wirelesly via a Belkin N1 router. Connecting to the Internet works just fine: speed is good, connection is strong, etc.
    But connecting to shared drives over my home network - specifically, those on my MacPro - has become deadly slow. It can take hours to transfer files of a few MBytes. The MacPro is connected to the network via Ethernet. It has four full drive bays. The Internet performance (e.g., web browsing) on the MacPro is fine.
    I previously has a PowerBook G4, and it did not have this problem - network speeds worked fine. It's only after I moved to the MBP that this started.
    This problem occurs even if a connect the MBP to the network with an Ethernet cable.
    Any suggestions are appreciated.
    MacBook Pro/PowerMac   Mac OS X (10.4.9)  

    William:
    I've got DHCP turned on in the Belkin, so it's handing out IP addresses. The router does connect to a switch, and I haven't tried a different port on the switch, or resetting it, but I will.
    One other thing to note - I have a Mac Mini as well; the Mini runs wirelessly. The connection from the MBP to the Mini has slowed down as well.
    I was going to pick up an Airport Express router this afternoon and try it. If nothing else, I'll have a nice collection of Apple hardware...
    Thanks for the feedback.
    MacBook Pro/PowerMac   Mac OS X (10.4.2)  

  • Firefox 3.6.10 in Ubuntu 10.04 recently became slow and often doesn't find websites.

    Firefox 3.6.10 in Ubuntu 10.04 recently became very slow and often doesn't find websites, especially those in My Yahoo, whereas Chromium works fine. When searching for a website, a dialog finally pops up saying "Server not found" "Firefox can't find server at finance.yahoo.com" When searching for, say, M&T Bank, Firefox says "looking up dnssearch.rr.com" My Internet Service Provider" is Time Warner's Road Runner. I followed the directions for Firefox not finding some websites by changing my connection setting to "no proxy", by disabling IPv6 and DNS prefetching to no avail. I uninstalled Firefox and then re-installed it - no change. I went to Tools > clear recent history, but the latter was shaded and unclickable.

    You can try "Reset all user preferences to Firefox defaults" on the [[Safe mode]] start window.
    Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).<br />
    See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]
    Create a new profile as a test to check if your current profile is causing the problems.<br />
    See [[Basic Troubleshooting#Make_a_new_profile|Basic Troubleshooting&#58; Make a new profile]]
    If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
    See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

Maybe you are looking for