Slow broadband after a line fault

Hi,
I recently returned from a week's holiday and found my broadband was dropping out almost every few minutes and was incredibly slow. I also had no dialling tone on my home phone line.
An Openreach engineer called this morning and found that a very old extension wire running through the house was causing the problem. He disconnected the troublesome wire, and now I have a good phone line and a stable broadband connection (connected for over 3 hrs without a problem).
However, the broadband is still very, very slow - the downstream is only 239kbps.
I have very little knowledge about broadband technology, but after a few hours researching I seem to have reached the conclusion that the reason for this is the connection kept dropping out whilst I was away on holiday. This has caused my IP profile to be set at 135kbps (determined by using the BT speed checker). A lot of the forums say that the IP profile will return to normal once the line has been stable for 3-10 days.
So, I guess I'm just looking for some reassurance that after a few days the line will return to normal.
If anyone can set my mind at rest, I'd be most grateful.
Phil
Solved!
Go to Solution.

Here are stats from hub:
DSL Connection
Link Information
Uptime:
0 days, 3:57:27
Modulation:
G.992.3 annex A
Bandwidth (Up/Down) [kbps/kbps]:
444 / 239
Data Transferred (Sent/Received) [MB/MB]:
11.31 / 29.76
Output Power (Up/Down) [dBm]:
12.5 / 0.0
Line Attenuation (Up/Down) [dB]:
26.5 / 47.5
SN Margin (Up/Down) [dB]:
27.5 / 31.5
Vendor ID (Local/Remote):
TMMB / IFTN
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
0 / 0
FEC Errors (Up/Down):
0 / 86
CRC Errors (Up/Down):
0 / 0
HEC Errors (Up/Down):
0 / 0
Line Profile:
Fast
And from BT Speed tester:
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
58 Kbps
0 Kbps
250 Kbps
Max Achievable Speed
 Download speedachieved during the test was - 58 Kbps
 For your connection, the acceptable range of speedsis 100-250 Kbps.
 Additional Information:
 Your DSL Connection Rate :239 Kbps(DOWN-STREAM), 444 Kbps(UP-STREAM)
 IP Profile for your line is - 135 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 24.53:21.32:54.15 (SBE:NBEBE)
These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
2. Upstream Test: -provides background information.
Upload Speed
258 Kbps
0 Kbps
444 Kbps
Max Achievable Speed
>Upload speed achieved during the test was - 258 Kbps
 Additional Information:
 Upstream Rate IP profile on your line is - 444 Kbps
Thanks.

Similar Messages

  • Slow Broadband after phone line fault rectified

    Joined BT Broadband Option 1 on 15/02/11, all was well with linespeed up to 6mbs while stabilising, On the 16/02/11 I reported a Phone fault (Broadband reverted to 135kbps) Phone fault was rectified on 18/02/11 and was told it would be 3 days before my broadband started to improve, it is now 24/02/11 and my Ip profile is still at the fail safe 135kbps, Anyone Help please.
    Line state: Connected
    Connection time: 0 days, 19:19:09
    Downstream: 286.3 Kbps
    Upstream: 440 Kbps
    ADSL Settings
    VPI/VCI: 0/38
    Type: PPPoA
    Modulation: G.992.5 Annex A
    Latency type: Interleaved
    Noise margin (Down/Up): 26.3 dB / 23.2 dB
    Line attenuation (Down/Up): 30.3 dB / 16.8 dB
    Output power (Down/Up): 17.9 dBm / 12.9 dBm
    FEC Events (Down/Up): 1528 / 2
    CRC Events (Down/Up): 0 / 32
    Loss of Framing (Local/Remote): 0 / 0
    Loss of Signal (Local/Remote): 0 / 0
    Loss of Power (Local/Remote): 0 / 0
    HEC Events (Down/Up): 0 / 7
    Error Seconds (Local/Remote): 0 / 0
     Download speedachieved during the test was - 52 Kbps
     For your connection, the acceptable range of speedsis 100-250 Kbps.
     Additional Information:
     Your DSL Connection Rate :286 Kbps(DOWN-STREAM), 440 Kbps(UP-STREAM)
     IP Profile for your line is - 135 Kbps
    Thankyou chas2209
    Solved!
    Go to Solution.

    Hello,
    Your noise margin does seem high but the speed does take about 3-10 days to build up after faults. I had the same issue if you call tech help desk 0800 111 4567 they will be able to sent you profile higher.

  • Very slow broadband speed following line fault

    Having recently had a noisy line fault repaired I have been left with broadband that is running at a very slow speed. Having read several other posts on this forum it seems that my IP profile needs resetting in the local exchange. I am reluctant to try to explain my problem to someone in India (because I can envisage a rather lengthy call which could possibly be to no avail) so can anybody tell me if there is an alternative way to reset my IP profile.
    BT's speed test results were as follows:
    Download speed: 680Kbs
    DSL connection rate: 2464Kbs (downstream)  448Kbs (upstream)
    IP Profile: 750Kbs
    Any help would be useful,
    Jim
    Solved!
    Go to Solution.

    Soulvache wrote:
    reme8488 wrote:
    You have 2 choices -
    1:  wait the 3 - 5 days and see if your profile resets (providing you have a stable connection for the period and leave your modem on 24/7)
    or
    2:  contact the moderators here to see if they can be of help.
    I think you'll be stuck with the former though.
    Tom,
    As I have posted above, we have not even seen Jim's line stats. This would make it impossible to try and establish what is actually occurring with the line and connection.
    I thought about that straight after posting (actually meant to put that bit in my op ) and then spotted your post when I was going to edit my own.  Was too quick on the keyboard there after watching a rather entertaining Fullham vs Chelsea match on my lappy.
    Kind regards... Tom
    BT Infinity2:

  • Slow Broadband after line fault fixed

    Hi,
    After a fault was fixed on the line two weeks ago Broadband speed has been incredibly slow - 32kBs at the most (previously it was around 400kBs)
    After replacing the microfilter, resetting the router, plugging directly into the test socket I just left it alone but have seen no improvement.
    Tried the quiet line test and all seems fine.
    Looks like the router disconnected at least once, otherwise the connection time should be longer
    Stats today...
    Line state:
    Connected
    Connection time:
    3 days, 22:43:33
    Downstream:
    287.1 Kbps
    Upstream:
    1.088 Mbps
    ADSL Settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.5 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    10.9 dB / 4.9 dB
    Line attenuation (Down/Up):
    44.2 dB / 28.1 dB
    Output power (Down/Up):
    17.6 dBm / 12.7 dBm
    FEC Events (Down/Up):
    134945 / 6918
    CRC Events (Down/Up):
    0 / 341
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    HEC Events (Down/Up):
    0 / 246
    Error Seconds (Local/Remote):
    0 / 211
    Any suggestions would be appreciated
    Also I saved the stats from the 29th Sept, the day after the line was fixed if they are any use, much the same except Noise Margin was 14.9 dB / 10.6 dB
    Solved!
    Go to Solution.

    Hi,
    Yesterday mods replied that there was indeed still a fault (didn't specify what) and they were looking into it.
    This morning broadband was back and faster than ever
    Thanks to all involved
    My current stats, in case anyone's interested... 
    Line state:
    Connected
    Connection time:
    0 days, 13:14:59
    Downstream:
    5.615 Mbps
    Upstream:
    1.04 Mbps
    ADSL Settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.5 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    9.6 dB / 5.7 dB
    Line attenuation (Down/Up):
    44.2 dB / 28.1 dB
    Output power (Down/Up):
    19.8 dBm / 12.7 dBm
    FEC Events (Down/Up):
    379372 / 686
    CRC Events (Down/Up):
    471 / 60
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    HEC Events (Down/Up):
    6422 / 41
    Error Seconds (Local/Remote):
    277 / 169

  • Slow Broadband after line fault

    Hi,
    I really hope i can some advice on here! I've been connected for over 18 months - never had a problem, brilliant BB speed (for my area) and was a happy customer. A fortnight ago my BB connection cut out suddenly but the phone was working ok. So I called 151 and did all the checks to make sure it wasn't my equipment and the line test eventually showed there was a line fault. I was told it would be fixed in due course which was fine.
    4 days later the steady blue BB light came back on on my hub (after flashing purple/orange for at least an hour) and since then my speed has been so bad it feels like I'm back on dial up! Downloading is impossible, the connection drops at least 3 times a day and the BB light on my hub goes back to the orange/purple light for long spells.
    Everytime I phone the fault line I get told that my line tests OK to wait untill my line 'settles in' again after having the fault. I've left it for over a week now and there has been no improvement at all - My router has been plugged into the test socket directly for the last 48 hours too but that made no change.. I'm sick fed up of being told to 'wait a while' by the indian fault team! I'm hoping for some advice on the state of the line from you guys - is it worth calling back the fault team (again!) and pushing for an engineer call out?
    I've done the noise test on 1707070 on a corded phone and there was a few crackles when i tried it the first time - second time seemed ok though.
    I've got a Home Hub 3.
    The first BT speed test I did came back saying they could not carry out my speed test as the line was slow and it diverted me to another website where I got these results:
    Download Speed (Mbps): 0.07
    Upload Speed (Mbps): 0.35
    Ping Latency(ms): 82.38 
    ADSL Line Status
    Connection information
    Line state:
    Connected
    Connection time:
    0 day, 01:21:52
    Downstream:
    8,128 Kbps
    Upstream:
    448 Kbps
      ADSL settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.1 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    12.9 dB / 25.0 dB
    Line attenuation (Down/Up):
    5.0 dB / 3.5 dB
    Output power (Down/Up):
    11.8 dBm / 12.0 dBm
    FEC Events (Down/Up):
    0 / 0
    CRC Events (Down/Up):
    0 / 0
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    Loss of Link (Remote):
    0
    HEC Errors (Down/Up):
    0 / 0
    Error Seconds (Local/Remote):
    0 / 0
    My Exchange is only about 400m away.
     Any information would be much appriciated (and sorry for the long post!)

    Results are:
    Download Speed (Mbps): 0.09
    Upload Speed (Mbps): 0.35
    Ping Latency (ms):  62.50
    Diagnostic test:
    1. Best Effort Test:  -provides background information.
    Download  Speed
    0.09 Mbps
    0 Mbps
    0.25 Mbps
    Max Achievable Speed
     Download speedachieved during the test was - 0.09 Mbps
     For your connection, the acceptable range of speeds is 0.05 Mbps-0.25 Mbps.
     Additional Information:
     Your DSL Connection Rate :8.13 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 0.14 Mbps

  • Slow Broadband after 21CN Upgrade?

    Before my scheduled 21 upgrade my download connection has been rock solid at 8000K for several years.  My whole recent experience with BT has been very disappointing and I hope you can throw some light on a solution.
    So Far:     
    My Equipment:  BT2000 Faceplate, RJ11 to BT Homehub 1010, 1 Extension fitted (No Bell wire Connected). 
    Problem 1. Now resolved.  On the day of my appointment the engineer connected my dial tone and broadband to someone else’s line in the next village.  The fault call centre insisted the fault could only be in my property as the line tested OK and I would have to accept the possible charges.  Despite my requests for them to despatch an engineer to the exchange as it is more than a coincidence that my dial tone disappeared at the same time as my scheduled changeover they insisted I have an appointment.  The fault was cleared in the exchange by the visiting engineer.
    Problem 2.  Now resolved. The engineer did not remove the call divert on my line and I missed my incoming calls for several days as my calls were diverted to a random number.  I tried #21# and this did not work, so I contacted BT again.  They informed me they could not remove the divert because they had not put it on. After investigation #61# managed to remove my divert.  When I asked why it was not removed when my line was fixed I was told that I must have put the divert on myself as it was done by someone with access to my line. The whole point that my line had been connected elsewhere was totally alien to the call centre worker.
    Problem 3.  On going
    After 14 days of Mediocare performance I was connected much slower speed than my old connection and as my profile was 4000k this is only half of my previous performance. (See Below)
    1. Best Effort Test: -provides background information.
    Download Speed
    5959 Kbps
    0 Kbps
    4000 Kbps
    Max Achievable Speed
     Download speed achieved during the test was - 5959 Kbps
     For your connection, the acceptable range of speeds is 1200-4000 Kbps.
     Additional Information:
     Your DSL Connection Rate :4603 Kbps(DOWN-STREAM), 1251 Kbps(UP-STREAM)
     IP Profile for your line is - 4000 Kbps
    The throughput of Best Efforts (BE) classes achieved during the test is - 16.4:29.53:54.07 (SBE:NBEBE)
    These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
    The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
    2. Upstream Test: -provides background information.
    Upload Speed
    873 Kbps
    0 Kbps
    1251 Kbps
    Max Achievable Speed
    >Upload speed achieved during the test was - 873 Kbps
     Additional Information:
     Upstream Rate IP profile on your line is - 1251 Kbps
    So I call BT again and after I have established that the only changing parameter is the new 21CN upgrade I am promised that a request will be passed to the engineers to increase the profile........  The result is that they just reset my profile, so once again my speed fluctuates for several days from a virtual stop to slow.
    It is now six days since reporting my slow speed problems after receiving several calls from BT to ask me if my speed has improved, I am finally a broken man today. 
    They insist that I have a broadband boost engineer, before I accept this, I ask several questions and failed to get any acceptable answers..
    What is wrong with my broadband?  You have a fault in the property (change the record!!)
    Why cannot you tell me the speed I am connected at.   You cannot WOOSH test me?  We cannot tell, we have to call you
    Can I speak to the engineers?  You cannot Sir
    Can I speak to your Boss?  No, why would you want to do that!
    What have you done in the exchange to fix my fault?  We have changed some things
    Do you thing it is acceptable to still have slow speeds after twenty days?  That's why you need a boost engineer
    What are you going to do differently from all the other people I have spoken to to resolve my issue.  Nothing
    So with no other option I accept that an appointment will have to be made again.  I am offered an appointment in the week, when I explain that I have business appointments and that I need a weekend appointment I am told none is available or would be available.  So I agree to a Monday appointment.  After the call I get a text to say I have an appointment has been made for Thursday!  So I have to call them back and ask for the appointment I have been promised and I am told it's a simple and easy mistake to press the wrong button, it happens quite often!!
    I since read here that it may help to upgrade my homehub, so why have they not sent me a replacement days ago?
    Current Performance:
    1. Best Effort Test: -provides background information.
    Download Speed
    2024 Kbps
    0 Kbps
    2000 Kbps
    Max Achievable Speed
     Download speed achieved during the test was - 2024 Kbps
     For your connection, the acceptable range of speeds is 800-2000 Kbps.
     Additional Information:
     Your DSL Connection Rate :2271 Kbps(DOWN-STREAM), 771 Kbps(UP-STREAM)
     IP Profile for your line is - 2000 Kbps
    The throughput of Best Efforts (BE) classes achieved during the test is - 13.35:23.63:63.06 (SBE:NBEBE)
    These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
    The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
    2. Upstream Test: -provides background information.
    Upload Speed
    592 Kbps
    0 Kbps
    771 Kbps
    Max Achievable Speed
    >Upload speed achieved during the test was - 592 Kbps
     Additional Information:
     Upstream Rate IP profile on your line is - 771 Kbps
    I know there are more important things going on in this world.  But my work, my ebay, my shopping, my banking, my social sites etc. all require bandwidth and to have it taken away disguised as an upgrade obviously upsets me.  I am shocked at the complete lack of communications, and the inability to listen and understand your customers.  What is the point of a call centre that can do NOTHING outside their script to help!
    Solved!
    Go to Solution.

    Not sure why my profile is still changing and why I was disconnected today, probably the call centre doing another line test. 
    Uptime:
    0 days, 10:24:37
    Modulation:
    G.992.5 annex A
    Bandwidth (Up/Down) [kbps/kbps]:
    803 / 2,523
    Data Transferred (Sent/Received) [MB/MB]:
    322.86 / 348.70
    Output Power (Up/Down) [dBm]:
    12.0 / 0.0
    Line Attenuation (Up/Down) [dB]:
    19.0 / 31.0
    SN Margin (Up/Down) [dB]:
    13.5 / 30.0
    Vendor ID (Local/Remote):
    TMMB / IFTN
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    1 / 0
    Loss of Power (Local/Remote):
    0 / 0
    Loss of Link (Remote):
    0
    Error Seconds (Local/Remote):
    1 / 0
    FEC Errors (Up/Down):
    0 / 0
    CRC Errors (Up/Down):
    0 / 0
    HEC Errors (Up/Down):
    0 / 0
    Line Profile:
    Fast

  • Slow broadband after repairs

    Like everyone else I have found the BT advisors a waste of time. After taliking for an hour each time to six or seven advisors in the last 3 weeks I was told there was a line fault and that it was now fixed. I have waited 5 days but the speed was about !Mbps at best. I talked to another advisor who said everything was fine and he would get the IP profile reset. I waited another 5 days and still the speed is lower than I should get. Before the fault I was getting about 3.6 Mbps for an IP profile of 4.0 Mbps. Now I get about 2.4 Mbps with the IP profile stuck for two days at 2.71 Mbps. Any help would be appreciated.
    The ASDL details are:
    ADSL line status
    Connection Information
    Line state
    Connected <script type="text/javascript"></script>
    Connection time
    2 days, 04:25:59
    Downstream
    3,071 Kbps
    Upstream
    1,107 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Fast
    Noise margin (Down/Up)
    12.4 dB / 5.6 dB
    Line attenuation (Down/Up)
    53.4 dB / 29.5 dB
    Output power (Down/Up)
    7.0 dBm / 1.6 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    0 / 0
    CRC Errors (Down/Up)
    7951 / 9
    HEC Errors (Down/Up)
    9159 / 0
    Error Seconds (Local/Remote)
    4918 / 4

    hi your ip profile is on the new 88.2% system that goes up and down immediately with any change of connection speed there fore it no longer needs resetting as the old system did
    the line fault has increased your noise margin which has lowered your connection speed once you have maintained a 3 day connection you can contact the forum mods and get them to reset the noise margin for you this is a link to them
    http://bt.custhelp.com/app/contact_email/c/4951
    they normally reply by email or phone directly to you within 3 working days
    They are a UK based BT specialist team who have a good record at getting problems solved
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • Slow broadband after line repair

    FAQ
    <script type="text/javascript"></script> Test1 comprises of Best Effort Test: -provides background information.
    Download  Speed
    71 Kbps
    0 Kbps
    250 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 71 Kbps
     For your connection, the acceptable range of speeds is 50-250 Kbps.
     Additional Information:
     Your DSL Connection Rate :4576 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 135 Kbps
    If you wish to discuss these results please contact your ISP.
    If you are experiencing problems with specific applications, servers or websites please contact your ISP for assistance.
    Your test has completed please close this window to exit the performance tester.
    Please visit FAQ section if you are unable To understand the test results.
    Ok so My line had problems and was fixed, over 24 hours ago but my profile is still limited at 135mb.  The BT guys in India are worse thean useless and there seems to be no way of talking to someone who actually understand IP config limits and can re baseline this profile.  The wait another 24 hours each time you talk to anyone at BT wears very thin.
    Any suggestuions?

    has your router managed to hold your connection without disconnections since the engineer visit?
    If so and you profile has not increased by tomorrow then I would email the mods for assistance giving your account and phone number and a link back to this thread [email protected]
    I think your profile may wll be stuck and need a 'kick' into action
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Very slow connection after phone line repair

    I had my phone line repaired yesterday with new cabling and new BT box for phone and computer.My phone is fine, but the hub for my broadband does not appear to be ok.  the phone symbol on the hub did not light up at all  this morning, and after restarting the hub and going back to default settings it is now glowing orange only.  It was ok yesterday after being fixed. Very slow connection now. Should i keep  everything on  to see if it will right itself, or re-start yet again?
    I have been looking on BT's options for fixing but can't seem to find anything. the connections in my area are fine so it can't be an outside fault

    Which home hub do you have? Did you recently re-contract or change your package, as that will affect your hub phone.
    As for the speed issue, it should get better if you leave it alone.
    See Why has my speed dropped
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Slow Broadband 250K throughput, line continually d...

    I joined BT in October 2010, I left Sky because my broadband speed was really good then one month they dropped the speed, no notice or apologies. I joined BT as I thought they would be able to provide a fast, quality and reliable service; this has not been my experience so far.
    Summary
    Problems since joining in October 2010, 6 months on still not fixed.
    Line throughput is configured to 250kbps, Profile is configured to 3776kbps.
    Current download speed is 0.12mbps, this is my average download speed.
    Line drops every 4-5 days, profile is reconfigured then drops again.
    4 failed BT Broadband engineer visits (engineers did not turn up).
    Card changed on the switch twice.
    If there is anyone from BT who cares about their customers please contact me to try and resolve.
    Line state
    Connected
    Connection time 0 days, 6:35:39
    Downstream 3,776 Kbps
    Upstream 448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type PPPoA
    Modulation ITU-T G.992.1
    Latency type Interleaved
    Noise margin (Down/Up) 14.9 dB / 22.0 dB
    Line attenuation (Down/Up) 43.0 dB / 28.5 dB
    Output power (Down/Up) 18.9 dBm / 12.0 dBm
    Loss of Framing (Local) 156
    Loss of Signal (Local) 2266
    Loss of Power (Local) 0
    FEC Errors (Down/Up) 16124 / 0
    CRC Errors (Down/Up) 8 / 2147480000
    HEC Errors (Down/Up) nil / 1
    Error Seconds (Local) 5460

    A complex broadband engineer attended my premises on Friday, he spent 2.5 hrs testing and could find nothing wrong with the internal wiring he dsaid I should be able to receive 4.7mb download with no problems. 4 hours after he left and my router threw a wobbly, continually rebooting with the amber and red light on occasions. Surprise, surprise the speed returned to the usual poor speed of 0.12mbps download.
    I have run BT Speedtester tonighht and it gets worse 67KBPS download, line profile now configured as 160kbps, see results below.

  • Slow broadband after exchange upgrade

    My exchange (Accrington) was recently upgraded. Prior to the upgrade I was getting approx 5.5Mb.
    I was told that I would need to wait 10 days after the upgrade for re-training of my line.
    After 10 days, my connection had dropped to 1.6Mb, so I called BT and was told that it was because I had a home hub version 1.0 and that it was incompatible with the upgraded exchage.
    New version 2.0 Hub was sent to me and this has now been connected for 5 days. I also took the opportunity to move things arround so the new hub is connected directly to the master socket, there is no extension wiring and no telephone connected. (Master socket has BT broadband accelerator filter fitted)
    I have used BT speedtest and got the stats from my hub. My IP Profile is no where near what it used to be, I would have expected this to rise after 5 days ?
    Any suggestions as to what I should do now ?
    By the way I am 456M from the exchange !
    Line state
    Connected
    Connection time
    0 days, 19:09:33
    Downstream
    2,268 Kbps
    Upstream
    1,184 Kbps
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.5
    Latency type
    Interleaved
    Noise margin (Down/Up)
    28.9 dB / 4.4 dB
    Line attenuation (Down/Up)
    16.0 dB / 7.1 dB
    Output power (Down/Up)
    0.0 dBm / 13.0 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    0 / 4294967137
    CRC Errors (Down/Up)
    0 / 2147480000
    HEC Errors (Down/Up)
    nil / 0
    Error Seconds (Local)
    0
    1. Best Effort Test: -provides background information.
    Download Speed
    1555 Kbps
    0 Kbps
    2000 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 1555 Kbps
     For your connection, the acceptable range of speedsis 800-2000 Kbps.
     Additional Information:
     Your DSL Connection Rate :2268 Kbps(DOWN-STREAM), 1183 Kbps(UP-STREAM)
     IP Profile for your line is - 1750 Kbps
    The throughput of Best Efforts (BE) classes achieved during the test is - 9.13:22.36:68.51 (SBE:NBEBE)
    These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
    The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
    2. Upstream Test: -provides background information.
    Upload Speed
    976 Kbps
    0 Kbps
    1183 Kbps
    Max Achievable Speed
    >Upload speed achieved during the test was - 976 Kbps
     Additional Information:
     Upstream Rate IP profile on your line is - 1183 Kbps
    We were unable to identify any performance problem with your service at this time.

    Thanks for the reply.
    I have removed the filter, and I will leave it for a few days to see if I get any improvement.
    The noise margin(down) actually increased slightly after removing it, is this to be expected ?
    Line state
    Connected
    Connection time
    0 days, 0:01:28
    Downstream
    2,268 Kbps
    Upstream
    1,236 Kbps
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.5
    Latency type
    Interleaved
    Noise margin (Down/Up)
    29.1 dB / 6.0 dB
    Line attenuation (Down/Up)
    16.0 dB / 7.0 dB
    Output power (Down/Up)
    0.0 dBm / 12.1 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    0 / 0
    CRC Errors (Down/Up)
    0 / 2147480000
    HEC Errors (Down/Up)
    nil / 12
    Error Seconds (Local)
    0

  • Slow down after my line was upgraded to ADSL2+

    Hi there
    a couple months ago BT upgraded our line from ADSL 1 to ADSL2+ now it all sounds good but I have experienced some major slow downs since they have done it and constant calls to CS have just resulted in my line getting tested and then having a different person phone back to give the results but just end up getting another line test done and it is starting to get very annoying.
    Before the upgrade I was downloading at around 8.1Mb/s, uploading at 1.1Mb/s and had a ping of around 15. Now it is this.
    Is there anything else i could do that could improve my speed?
    Thanks for reading my wall of text.
    P.S my line stats are:
    Connection information
    Line state
    Connected
    Connection time
    10 days, 6:53:35
    Downstream
    2,268 Kbps
    Upstream
    888 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.5
    Latency type
    Interleaved
    Noise margin (Down/Up)
    13.1 dB / 12.6 dB
    Line attenuation (Down/Up)
    21.5 dB / 9.5 dB
    Output power (Down/Up)
    0.0 dBm / 12.5 dBm
    Solved!
    Go to Solution.

    Hi there
    I am using BT home hub 2.0
    and the rest of my line stats
    Line state
    Connected
    Connection time
    10 days, 7:16:00
    Downstream
    2,268 Kbps
    Upstream
    888 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.5
    Latency type
    Interleaved
    Noise margin (Down/Up)
    13.1 dB / 12.5 dB
    Line attenuation (Down/Up)
    21.5 dB / 9.5 dB
    Output power (Down/Up)
    0.0 dBm / 12.5 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    898476782 / 0
    CRC Errors (Down/Up)
    202 / 2147480000
    HEC Errors (Down/Up)
    nil / 0
    Error Seconds (Local)
    143

  • Slow broadband after upgrading from Homehub 2 to 4

    Upgraded from our old, dependable Homehub 2 a couple of moths ago. Was offered Homehub 4. Since then, with nothing else changing, we found the speed to be a lot slower, both on wired (Ethernet) connections and with wireless. We have quite a few devices connected (3 PC's, 1 AppleTV box on Ethernet and a couple of IPad 2's, Wii and couple of phones on WiFi) but didn't have a problem before. I am seriously thinking about putting my Homehub 2 back. Can anyone throw any light or give any suggestions as to why we have these speed and connection issues? TIA<script charset="UTF-8" type="application/javascript" src="chrome://hdv/content/hdv.js"></script>

    welcome to the BT community forum where customers help customers and only BT employees are the forum mods
    in order for the forum members to help please can you run  btspeedtester  (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
    are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    Someone may then be able to offer help/assistance/suggestions to your problem
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Slow speeds after transient line noise

    Morning.
    I've had a problem with line noise this morning that seems to have re-set the IP profile for my line (speed test attached).
    Could an admin please look into this?
    Many thanks in advance.
    -John-
    Download speed achieved during the test was - 4895 Kbps
     For your connection, the acceptable range of speeds is 1000-7150 Kbps.
     Additional Information:
     Your DSL Connection Rate :13219 Kbps(DOWN-STREAM), 1151 Kbps(UP-STREAM)
     IP Profile for your line is - 5000 Kbps
    The throughput of Best Efforts (BE) classes achieved during the test is - 13.36:20.65:65.99 (SBE:NBEBE)
    These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
    The results of this test will vary depending on the way your ISP has decided to use these traffic classes.

    Hi Waub,
    Thanks for the email, I'll get back to you shortly about this, need to check a few things first.
    Ta,
    Stephanie
    Stephanie
    BTCare Community Manager
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Slow Broadband after 10 days

    I have had ADSL now for 10 days and it is resolutely stuck ay 2gb despite the stats showing a good connection to the exchange
      When I run speed test I get :
     Download speedachieved during the test was - 1.71 Mbps
     For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps.
     Additional Information:
     Your DSL Connection Rate :8.13 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 2 Mbps
    I seem to be stuck at 2Mb/s
    I have spoken to the help line and tried just using the master socket (with faceplate removed and a microfilter plugged in but no phones or other wiring attached).   Any suggestions what to do next?
    ADSL Line Status
    Connection Information
    Line state:
    Connected
    Connection time:
    5 days, 22:32:55
    Downstream:
    7.938 Mbps
    Upstream:
    448 Kbps
    ADSL Settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.1 Annex A
    Latency type:
    Fast
    Noise margin (Down/Up):
    14.5 dB / 22.0 dB
    Line attenuation (Down/Up):
    21.4 dB / 13.0 dB
    Output power (Down/Up):
    19.9 dBm / 11.9 dBm
    FEC Events (Down/Up):
    0 / 0
    CRC Events (Down/Up):
    2 / 8
    Loss of Framing (Local/Remote):
    0 / 0
    Loss of Signal (Local/Remote):
    0 / 0
    Loss of Power (Local/Remote):
    0 / 0
    HEC Events (Down/Up):
    0 / 0
    Error Seconds (Local/Remote):
    2 / 8
    Solved!
    Go to Solution.

    Hi it looks as though you have a stuck IP profile if you contact the forum mods they can get this reset  for you  this is a link to them
    http://bt.custhelp.com/app/contact_email/c/4951
    they normally reply by email or phone directly to you within 3 working days
    They are a UK based BT specialist team who have a good record at getting problems solved
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Maybe you are looking for

  • Email Problem

    Need help... I can't get my emails, yet my wife still gets hers on our iPad  Mini.  I keep getting -- "Cannot Get Mail" ..."mail server 'mobile.charter.net' is not responding" Need someone to walk me through this....Thanks!

  • CFC9 settings for re read stocks and Reduction Quantities.

    Hi Gurus, We had stock inconsistencies heavily. We went to SAP and they suggested to select re read stocks option in CFC9. When we selected the option and ran batch job for CCR, it was running morethan 2 days and completed. Ususally it will complete

  • Tracking websites visited by employees

    Hello all, Need a little advise. Our owner got really upset when he found out about a couple of employees that were spending time surfing on the web and not taking care of bussiness. We are currently running SBS 2008 Premium. The router we have in pl

  • Lightroom 2.6 preference file location on Windows 7

    I have just installed windows 7 on my laptop and want to copy my preference file from my desktop Vista machine over so I have the same setup. I located the preference file in vista under users/myname/appdata/roaming/adobe/lightroom as per the post on

  • How to execute this procedure(having out parameters)

    PROCEDURE emp_cursor ( v_deptno IN VARCHAR2, v_doj OUT DATE, v_empno OUT NUMBER, v_sal OUT NUMBER );