Slow connection speed, 3rd time in 2 Months

Getting pretty sick of this now it has happen 3 times now in 2 months, my connection speed has dropped to 0.20Mbps. What's going on, it's has never happened between 2004 to September 2012, It's stopping me from playing online games, it takes ages to load webpages and it takes ages to load youtube videos even in 240p. and nothing has been changed or moved.
My router is a BT voyager 2091, I tried the BT speed checker, but they said my connection was too slow -.-
Current results:
Help?!
Thanks Ben
Solved!
Go to Solution.

Microfilter install correctly to an older master socket, quiet line test had no problems, no noise, no hissing.
Hope this helps more
Ben

Similar Messages

Slow Connection speed at all times, with regular d...

I would really appreciate any advice you have to offer! (P.s Connection time is so low because I recently connected the router to the test socket to see if there was a problem with my internal wiring)
I've been experiencing a slow connection speed (even though the router is connected to the master socket) much slower than with my previous provider and a very intermittent service. The broadband connection seems to drop out every time the landline is in use and when using the landline you can hear a lot of static/crackling in the background.
Connection Information
Line state:
Connected
Connection time:
0 days, 01:32:51
Downstream:
1.12 Mbps
Upstream:
444.9 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
5.4 dB / 8.6 dB
Line attenuation (Down/Up):
29.6 dB / 14.8 dB
Output power (Down/Up):
19.4 dBm / 9.9 dBm
FEC Events (Down/Up):
1412 / 0
CRC Events (Down/Up):
0 / 32
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 131
Error Seconds (Local/Remote):
12 / 15
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
937 Kbps
0 Kbps
1000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 937 Kbps
For your connection, the acceptable range of speeds is 400-1000 Kbps.
Additional Information:
Your DSL Connection Rate :1146 Kbps(DOWN-STREAM), 444 Kbps(UP-STREAM)
IP Profile for your line is - 1010 Kbps
I would really appreciate any help and advice! (P.s the connection time is so low because I tried to connect the router to the test socket to check if the fault was with the wiring. The router is normally on 24/7 and these problems still occur)
Solved!
Go to Solution.

Hi and welcome to the forum.
Have you tried another known working telephone into that test socket without an ADSL fiter.
If you have done all that you will need to report to your comms provider, if its BT Retail you will need to call them on 0800 800 151 or 0330 123 4151 from a mobile phone.
They will mention about charges but as long as you have done as suggested and you have not damaged any of the incoming wiring there "should" be no charge. when you phone do NOT mention broadband once any noise on your line is solved then your broadband will improve
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Im getting slower Connection speeds

Im getting slower connection speeds then what i ordered i got the 15mps and i only get 10 ?

It looks like you're right at the edge of the 10Mbps service limit for your copper line, as your margins are low and the line speed is incorrect.
Do you have access to a NID? If so, can you plug your modem into your NID's test jack and pull up the new statistics it shows? The NID can often times be found outside on the side/rear of your home, near your electrical panel/meter or on a pole near the street (uncommon for the last one).
========
The first to bring me 1Gbps Fiber for $30/m wins!

WRT160N SLOW CONNECTION SPEED

I have slow connect speed when using the WRT160N. I have tried every thing, done dianogstics on connection, router, modem, thru three diffeant software, norton, windows, system machinics. when ising the router some days the speed is amost like using dial up
I use XP, on both a laptop desk top, up to date drivers, both cna use wifi or direct connection by cat 5e, 3 m of ram, a wimax internet server,,,,, (company called Bridge Maxx)
But when I stop using the router and connect directly to the modem no problem works fine,,,,, not sure what to do........ just need my wifi back,,,,so i cna work,

Whats the Version number of your Router, If you have having version2 router, then there is an knows issue with Version2 Router. Downgrading to Build 8 is generally accepted to correct these issues, however Linksys have indicated to several people they do not have the build 8 firmware to give to end users.
This is ONLY for WRT160N V2 routers. This firmware will not work on WRT160N V1.
You can find it at http://audipages.com/router/
Follow the dowload and firmware downgrade instructions on that page.
Once you upgrade the firmware of your router, you need to Reset your Router and Re-Configure all the settings on it back again. Once you do the settings on your router i think this should solve your problem.

Help : very slow connection speed with AEBS and iMac

I connect to the internet using my newly purchased AEBS. I have a MacBook and an 24" iMac ( purchased in Nov 2007). My iMac showed very slow connecting speed of <1 MB/s download; with my MacBook placed just 1 foot from my iMac, the MacBook showed an amazing download speed of 20MB/s. If i connect the iMac to the AEBS using ethernet cable, it can get a very high speed.
So, where is the problem??
I am new to wireless, please help. I use iMac more than my MacBook at home.
Actually, i did not touch the any of the advance setting of the AEBS.

You know, I am experiencing the same problem. My wife's PC and iPhone are blazing fast, but my MacBook is accessing the internet at about dial-up speeds. Very frustrating and I haven't yet found the culprit.
Anyone???

Slow connection speed imac but not macbook

Slow connection speed on my imac 2.4ghz intel core 2 duo running 10.6.8, I get download of 15mbs and upload of 9mbs but on my macbook pro 2.8ghz intel core i7 on the same desk I am getting 33mbs and 10mbs!
Can anyone help me out on this, thanks in advance.

The two key numbers here are: 1) Transmit Rate: 59 which is the current maximum bandwidth of the wireless connection in Mbps, and 2) The MCS Index: 6 which indicates that the iMac's connection to the BT Home Hub wireless is only using a single spatial steam. Forget the techo mumbo jumbo, your iMac is much more capable than that.
You should expect a Transmit rate closer to 130 Mbps on the 2.4 GHz radio. At least this explains the poorer performance of the iMac. I would venture to say that if you temporarily connected the iMac to the BT using an Ethernet connection the iMac would equal or exceed the MacBook Pro's bandwidth performance.
Has this always been an issue or something that has just recently started happening?

Very slow connection speed, after phone line probl...

My catalogue of problems starts about a month ago. The phone line developed heavy interference and my Broadband connection kept dropping. This was diagnosed as being a fault with my HH 1.5. BT duly sent me a replacement HH3 which arrived about 3 days later. I installed the new hub, changed all the wiring and the filters for the new kit that came with the hub only to discover that the interference on the phone line was now even worse. It was so bad that at times you could not even hear what was being said on the other end of the phone, so an engineer visit was arranged.
A week later a BT engineer came and checked the line, sure enough there was a second problem and all the wiring from my house to the nearest telephone pole had to be replaced.
These problems had had a catastrophic effect on my connection speed and profile (I was getting about 500 kbps both up and down stream), so I dutifully reset the hub after the engineer had finished and waited for the line to stabilise.
14 days later and the upload speed had doubled, but the download speed is still unchanged at 570 kbps, about half the current upload speed. The line was a bit temperamental for the first few days but I have been able to maintain a solid connection for the last 4 days, current stats are as follows:
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
4 days, 04:42:16
Downstream:
574.3 Kbps
Upstream:
1.184 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
29.9 dB / 5.6 dB
Line attenuation (Down/Up):
19.6 dB / 12.8 dB
Output power (Down/Up):
18.3 dBm / 12.4 dBm
FEC Events (Down/Up):
279 / 615
CRC Events (Down/Up):
0 / 94
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 156
Error Seconds (Local/Remote):
0 / 42
There is only one active socket in the house, and the hub has been running from the test socket for the last week.
Solved!
Go to Solution.

The Hub is connected to the test socket. Disconnecting the ADSL feed to the hub has had no real effect (The upload speed increased marginaly but still no change to the download speed). Reran speedtest too, the new stats are:
FAQ
1. Best Effort Test: -provides background information.
Download Speed
0.44 Mbps
0 Mbps
0.5 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.44 Mbps
For your connection, the acceptable range of speeds is 0.1 Mbps-0.5 Mbps.
IP Profile for your line is - 0.51 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.94 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.94Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 00:02:29
Downstream:
574.3 Kbps
Upstream:
1.2 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
29.9 dB / 5.9 dB
Line attenuation (Down/Up):
19.5 dB / 12.7 dB
Output power (Down/Up):
18.3 dBm / 12.4 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
0 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
6 / 63

Progressively Slower Connection Speed

Hi,
I'm having some difficulties with my BT Broadband speed. The connection is getting progressively slower. Each time the router recycles I get a lower connection speed.
According to the BT Wholesale checker I should be able to get 6.5-8Mbps but I've never seen > 3Mbps and am currently <2Mbps.
ADSL Max
Up to 7.5
6.5 to 8
Available
Fixed Rate
2
Available
I tried resetting the router tonight and got the following in my event log entries:
23:35:07, 15 Jul.
( 58.190000) ETHoA is up - VPI: 0, VCI:35
23:35:07, 15 Jul.
( 58.190000) DSL is up
23:35:06, 15 Jul.
( 56.710000) DSL noise margin: 9.00 dB upstream, 9.00 dB downstream
23:35:05, 15 Jul.
( 56.640000) DSL line rate: 448 Kbps upstream, 1984 Kbps downstream
23:34:43, 15 Jul.
( 34.020000) WAN Auto-sensing running.
The helpdesk details are:
1. Product name:
BT Home Hub
2. Serial number:
+068340+NQ33251108
3. Firmware version:
Software version 4.7.5.1.83.8.130.1.17 (Type A) Last updated 03/05/14
4. Board version:
BT Hub 4A
5. ADSL uptime:
0 days, 00:11:03
6. Bandwidth:
448 / 1984
7. Data sent/received:
2.0 MB / 8.0 MB
8. Broadband username:
[email protected]
9. BT FON:
Yes
10. 2.4 GHz Wireless network/SSID:
BTHub4-7QH7
11. 2.4 GHz Wireless connections:
Enabled (802.11 b/g) 20 MHz, WPS enabled
12. 2.4 GHz Wireless security:
WPA and WPA2
13. 2.4 GHz Wireless channel:
Automatic / 1
14. 5 GHz Wireless network/SSID:
BTHub4-7QH7
15. 5 GHz Wireless connections:
Disabled
16. 5 GHz Wireless security:
WPA2
17. 5 GHz Wireless channel:
Automatic / 0
18. Firewall:
Default
19. MAC Address:
cc:33:bb:d0:29:00
20. VPI/VCI:
0 / 38
21. Modulation:
G.992.1 Annex A
22. Latency type:
Interleaved
23. Software variant:
24. Boot loader:
I have a shielded cable connecting the router to the line-box and the line-box has an ADSL filter faceplate which ought to mean I don't need filters anywhere in the house. This was fitted by a BT engineer.
I would be grateful if anybody could make a recommendation as I've tried everything I can think of.
Thanks in advance,
Simon Burrows
Solved!
Go to Solution.

Hi,
I've left the router up for several days now with no decrease in connection speed:
5. ADSL uptime:
7 days, 00:01:00
6. Bandwidth:
448 / 1984
I've tried the quiet-line test with a corded phone and get a constant buzz.
The next thing I've tried is to disconnect the ADSL filter faceplate from the line-box and have plugged a different ADSL filter directly into the line-box. The quiet-line test still yields a buzz, albeit slightly quieter.
Now that I've reset the router (turned it off whilst swapping cables around), I now have the following (with a different ADSL filter):
00:00:08, 23 Jul.
( 65.750000) DSL noise margin: 10.00 dB upstream, 9.00 dB downstream
00:00:08, 23 Jul.
( 65.680000) DSL line rate: 448 Kbps upstream, 1952 Kbps downstream
5. ADSL uptime:
0 days, 00:02:53
6. Bandwidth:
448 / 1952

WDS slow connection speed

I have a New Mac Pro Tower connected to an AX b/g compatible WDS network and it gets 10k kbps download speeds.
The Problem is my iMac G5 connected to the same network has an extremely slow download speed of 583 kbps?
Anyone have a clue as to why iMac's internet connection speed is so much slower?

I have had the same problem since november 2007:
I connected an old airport extreme basestation and a brand new one through WDS.
it took me a while getting the WDS to be faultless. (the encryption caused issues). So with both in WEP mode I lost the last error messages and both devices tell me all is fine, but it isn't.
I have NO access to the Internet via the router. I have no access to anything on the other side. The same goes when I hoop up in the other side then I have no access to devices (IP-Cam, printers, routers, Mac's, PC's...).
What is wrong with WDS?
I removed the old aiport extreme and used only a TimeCapsule and the new Airport Extreme. Nothing changed.
The Internet is extremely slow and gives time outs.
Finally I pulled a 60m cable to the TimeCapsule

Slow transfer speed on time capsule

First of all im new to this whole MAC thing. I have a new IMac that can communicate with an attached Time Capsule. I can send files to and from the Time Capsule on the IMac at a decent rate.
I am having trouble with the Win & PC that I have also got on the same network. It can see the Time Capsule OK and can also send files to and get files from the Time Capsule OK, but the speed at which it does so is very slow as compared to the MAC.
I am getting about 2.5 MB/sec. I have a wireless N card on the WIN machine and by all apparent standards WIN shows the wireless connection at 802.11N with all signal bars with a connection speed of 144Mbps
Is there something I can do to speed this up ?
Thank you, Erich

The mac is at 195 - 250 on a regular basis.
To get that speed the mac is connecting on the 5ghz band.. The Mac also auto swaps bands.. PC cannot do that.
Apple restrict 2.4ghz to max 150mbps which will be 130 or 144mbps you are getting.
The best idea is to force the TC to give out different names for the two bands.. in the wireless setup give 5ghz a different name.. force the PC to join 5ghz.
The connection over 5Ghz is at a solid 300 on the PC and 450 on the Mac. Again, why cant they both connect at the same if they are using the same standards?
They are not connecting at the same standard.. PC is using a 300mbps card .. if you want 450mbps you will have to buy a compliant 450mbps card. This is new and really not part of the N standard.
And I tried to change the wireless channel on the PC USB adaptor but cant find an option for that under wireless properties. There are a lot of things to change, just not that.
You change channel on Tx.. not the Rx.. ie the host not the client.. all changes to wireless channels are made on the TC.

Super Slow Connection speed

Hi all, with any luck someone here will be able to offer some wisdom!
Until recently my broadband has been faultless (well not bad anyway), in the last week or so it seems to have nosedived in terms of performance, and I am struggling to work out why. I have been through India, and I have my modem plugged into the test port of the master socket, here is wat things look like in the Hub Manager:
Line state
Connected
Connection time
0 days, 0:53:56
Downstream
8,126 Kbps
Upstream
440 Kbps
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
20.3 dB / 32.9 dB
Line attenuation (Down/Up)
10.0 dB / 4.2 dB
Output power (Down/Up)
0.0 dBm / 12.0 dBm
Loss of Framing (Local)
34
Loss of Signal (Local)
3
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 4294967264
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 0
Error Seconds (Local)
3
The three errors are me pulling the cable out to rest the conenction. The massive FEC / CRC errors are a bug I think. Does anyone know about Loss of Framing and what 0dBm output power are?
I ran the BT speedtest and got some truly terrible results, which said that my profile was 7000kbps, good, and my download was 146kbps, bad.
Anyone know what might be causing my super slow connection? I disconnected all computers barring my laptop in case somethign was secretly thrashing the service, but it didnt help.
Thanks in advance,
Mark.

I have similar problems. My connection was fine until about a week ago, when I started getting noise on my phone.
This has now been fixed, but since then, my Broadband connection speed has dropped from around 2M to 135k. I had an engineer out this morning to check what had been fixed during the first engineer visit (to fix the phone) and once he'd finished, he tested in to the socket to find that he could get 7M speeds. However, since he's been gone, I've plugged my setup back in and still get speeds of 135k.
I've tried removing phone connection so only router plugged in, I've changed filter to see if that was the issue - only things I've not yet tried because they are more hassle first off is trying another ADSL cable and/or a new router
My Hub manager shows the following, but not sure if this helpful to anyone, or if anyone can point me in the right direction of other things to try, I'd be greatly appreciative.
Thanks
ADSL line status
Connection information
Line state
Connected
Connection time
0 days, 0:56:42
Downstream
8,128 Kbps
Upstream
448 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Interleaved
Noise margin (Down/Up)
15.7 dB / 22.0 dB
Line attenuation (Down/Up)
15.0 dB / 8.5 dB
Output power (Down/Up)
19.8 dBm / 12.3 dBm
Loss of Framing (Local)
34
Loss of Signal (Local)
3
Loss of Power (Local)
0
FEC Errors (Down/Up)
13 / 0
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 0
Error Seconds (Local)
3

Mavericks install incomplete. No Apple installers on HD. Will I be able to upgrade to Yosemite and will it fix all that didn't install with Mavericks upgrade? Very slow connection speeds 30 hrs to download Mavericks. Tried re-install; no help/

Ever since upgrade to Mavericks I have been having problems which are too numerous to mention. I finally found a program from a UCBerkley professor called Pacifier which indicated 4000+ of 400,000+ files and folders did not install. I was unable to go further to try to fix everything because Pacifier can't find ANY Apple installers on my HD. It recommended I download the Mavericks installer without reinstalling to continue; however, after having done so (very slow connection; takes 30 hours to download) and although the installer appears in apps while downloading it disappears and NO Apple installer packages can be found on my hard drive. I tried to download Yosemite once and it indicated my system wasn't eligible for the upgrade. Its' download time was similar to Mavericks; 28+ hours.
I am using a Macbook Pro mid-2012 version OS X 10.9.5 (13F34); Processor 2.5 GHz Intel Core i5; Memory 4 GB 1600 MHz DDR3; Graphics Intel HD Graphics 4000 1024 MB.
Regardless of how many files and apps I remove my memory is being eaten up to the point I can hardly do anything at all. There are no civil words for how frustrated I am. Someone please help me.
Thanks,
JJ

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

Classic Read Only Error-Irreparable partition-3rd time in 6 months

I have been using a 1 terabyte usb-powered Seagate Freeagent Go drive since May, when I got my 2010 Macbook Pro. I have had it set up with 2 partitions. One for general backups (Mac OS Extended(Journaled)) and one for Time Machine(Mac OS Extended(Case-Sensitive)), split evenly. Not sure why I assigned the time machine partition a case-sensitive format. I believe that journaled is a more secure format, but I am fairly sure that I have tried that before, with no success. The drive is partitioned based on GUID. I use Time Machine and I get through about three backups over 2 months(I don't have important info), and then the next time I try to use the drive, OSX reports that it is read only. I have been investigating this issue for 6 months, and I have never found a solution that works for me. I understand that this issue has been thrown around far too much already, but please understand me when I say that I have tried every solution I have found yet. unmounting and remounting the drive changes nothing. The same goes for restarting the computer. The same issue arises if I plug the drive into another computer. I learned early on that I needed to make sure to turn off scheduled backups, since I have the drive connected at irregular times. This should have prevented corruption. I always eject the drive before removing it. I have checked the permissions, and my account has full read and write privileges, but right beneath "Sharing & Permissions" in Get Info, it says "You can only read". I have attempted to change the permissions, but even when I unlock get info, the permissions box is still greyed out. I have attempted to repair the partition each time this happens, and the repair always fails. What really seems to set my situation apart from the others online is that I have a second partition on this hard drive other than my time machine partition, and it works consistently, and has never failed. I assume this means that my drive isn't failing, and I have been ejecting the drive properly, because otherwise both partitions should be corrupted. I still have time machine set to only backup when I tell it to. I must note that I did notice this issue the most recent time immediately after I reconnected the drive following a time machine backup. I went on vacation, but right before it I backed my computer up. When I returned, I plugged the device in, and OSX immediately notified me that the drive was read only. I am ready to do anything(that costs no money-I am a college student) to prevent this from occurring again in the future. I do not need the backups I have made. I welcome any suggestions, and Happy New Years Eve!

Iteo wrote:
I have been using a 1 terabyte usb-powered Seagate Freeagent Go drive since May, when I got my 2010 Macbook Pro.
Does that drive come with a cable with two USB plugs? Many bus-powered external drives are cheap and targeted to the PC market. They need more power than a single USB plug will provide. It is probably randomly losing power, unmounting unexpectedly, and getting corrupted.
I have had it set up with 2 partitions. One for general backups (Mac OS Extended(Journaled)) and one for Time Machine(Mac OS Extended(Case-Sensitive)), split evenly. Not sure why I assigned the time machine partition a case-sensitive format. I believe that journaled is a more secure format,
Not having journaling turned on will only exacerbate the problem. Using case sensitive is just a bad idea. You should fix that right away.
I am fairly sure that I have tried that before, with no success.
Humor us this time
I have been investigating this issue for 6 months, and I have never found a solution that works for me. I understand that this issue has been thrown around far too much already
Really? This is the first time I've seen it. This is also the first time you've asked a question about it here on Apple Discussions. Perhaps you were taking advice from less reputable sources.
I learned early on that I needed to make sure to turn off scheduled backups, since I have the drive connected at irregular times.
That is irrelevant. Time Machine doesn't care. It will bug you after ten days, but that is all.
I am ready to do anything(that costs no money-I am a college student) to prevent this from occurring again in the future. I do not need the backups I have made. I welcome any suggestions, and Happy New Years Eve!
Repartition that drive. Use default settings. Turn on Time Machine. Enjoy.

Very slow connection speed

Very slow internet speed past 10 days. Have completed 1) VIOS recommended optimizer; 2) speed check (3.1 down, time out on upload); 3) diagnostic check (never completes analyzing); 4) turning router and devices off/on. Any other suggestions appreciated. Thanks

PLEASE NOTE MY LOCATION.
MY FiOS SERVICE MEETS MY NEEDS
Tom
Freedom Essentials, QIP 7100 1,Bose SOLO TV Sound System,,QIP 7216 P2,M1424WR Rev F, iPad 2 WiFi,iPhone 5,TV SYST INFO Release 1.9.5 Build No. 17.45
Data Object 39.45
Attachments:
FiOS Internet Speed Tests 1 5 2014.pdf ‏41 KB

WRT54G3G-ST very slow connection speeds

Hi,
I recently purchased a wrt54g3g-st router for mobile broadband and I have had some problems with the connection speeds. I have called linksys support but they were no help. I am using a PC-5740 broadband card which works perfectly fine in laptops by itself. When I am connected through the router its shows that I have 54.0 Mps speed but the pages load about as slow as dial-up speeds
Thanks for any help you can give me on this problem

if loading the pages is the only problem then try adjusting the mtu settings on the router ui to 1392 ....

Slow connection speed, 3rd time in 2 Months

Similar Messages

Maybe you are looking for