SLOW IDE scan
Hi Folks,
just bought a KT4 Ultra, and nearly everything works fine. Only two drawbacks:
- As it scans automatically for all IDE masters and slaves it takes just a half eternity until it recognizes the primary master. After that the rest of the scans is rather speedy.
Any chance how to speed up things?
- My 4 IDE devices are connected via identical U-IDE cables. But BIOS claims that the primary master (actual Maxtor HD, 80 GB) is not connected via 80-pin wire and so it works only with DMA 2 instead of 5. Chnaging the cables has no effect.
Any idea?
Bye..............Ralf
Hi Ralph..
SOmetimes, this sort of thigs happen when the IDE cables are bent, or not plugged in properly.. But since u changed the cable, i dont think that this is an issue.. I hope u have a good PSU cos u are using 4 ide devices.. Im not sure wether the power affects the IDE scanning but who knows
Regards
Rasika
Similar Messages
-
I'll make this short and too the point...
2 problems. I need help.
System Setup:
Antec 350 psu
6585mobo
AMI BIOS version A6585SMS V1.5 02142003
1.8ghz cpu
256meg ram
eVGA GF4 MX440se
WD400BB
ASUS 52x24x52 CDRW
USR 56k fax modem
The first problem is that the POST IDE scan takes entirely too long. I would say 30sec to 1 min to do the IDE scan.
Secondly, after a successful shutdown and power-up, the scan does not show the HD during the POST IDE scan, then it asks for a bootable disk and press any key to continue.
To correct this problem, I've had my customer enter into BIOS and immediately exit out by selecting save changes and Exit. This procedure works 100% of the time but it is a pain.
Is there anything that someone can point me to to correct this issue in order to satisfy my customer?you have a WD HD so if it is the only device on the drive just pull the jumper off it and leave it off. If your cd-rw is on the same ide cable set HD to master and cd-rw to slave.
-
K7T Turbo2 Not Detecting on IDE scan.
Antex 300w.,MSI K7T Turbo 2,AMD AthlonXP 2000+,300mb SDRAM, Maxtor40G (7200rpm ATA/133),NVidiaGeForceMX/MX-400,52xCD/R-RW,16XDVD ROM,Ultra ATA/133 High Speed Dual Channel Controller,WinXP. When I boot this machine it detects on first screen, IDE Detect, as it should. When it gets to IDE scan screen it shows 0 thru 3 "not detected","press esc to continue or ....... to enter setup. then it shows what I call Scan Disk, white/black bar line that goes all white to show progress. It then take alot of time to open XP to desktop. BIOS is set at Optimized selection. What am I missing?? Bad Board? Bad Builder (me)???
Think that line is not showing progress of scandisk, but ending time to make a selection of entering setup or select a bootable device...
-
IPad one nearly 3 years old has got very slow - ideas?
My iPad will be three years old in June. In the last few weeks it has got very slow - sometimes apps take ages to respond and have to be touched several times - the same with scrolling and in fact any touch control. Even then it is slow to load things.
It is a 64 gb which is only just over half full so I don't think it is because there isn't much memory.
Any ideas?Try a reboot by holding both the power and home buttons until the apple logo appears and it restarts, ignoring the red slider if it appears.
Memory overloads can cause slow down and reboot clears those. -
Scanning using the Mac scanning application "Image Capture" is extremely slow. I have a new iMac with i7 processor and 32GB of RAM; scanning takes over *one minute* and seems to peg my CPU. Any suggestions?
I had a similar problem and found using the "ControlCenter" software from Brother and then reducing the scan resolution from 300x300 to 100x100 made it much faster.
Scanner Driver (TWAIN)
This download includes the BrotherControlCenter software for easy to use one button scanning from your Mac or machine Scan-to button.
close
06/06/2014
(3.9.1-343b)
7.04
MB -
Nvidia SLOW-SLOW IDE performance.
Afternoon.
Something has gone terribly wrong with my board, or the drivers that I use under XP.
When I bought the board, I was able to write 2x16 DVD's at once from ISO images. I have two BenQ 1620 DVD drives. Now, when I try to do the same, Nero slows down to the point where there is almost now activity on the harddrive. But this only happens when I use both recorders at once. If I use one recorer, it's work OK at 16x.
DMA is enabled, and I can't see anything wrong with my setup under windows - perhaps you guys can give me some ideas. Latest NVIDIA drivers for windows/compatible firmwares etcetera.. I have the K8N SLI Platinum.
David.I think I've found the problem..
The file I tried to write had 118,000 sements. After I ran defrag on my machine, the problem is now solved...
David. -
So, my problem is that my cpu´s cd-rom devices are extreme slow. SiSoft sandra benchmarks my DVD about 4000kb/s and my CDRW 2500kb/s.
I had same problem with my hardrive when i used IDE drivers from utility cd but when i installed new IDE driver from internet (Siside39?) i got my hd running good (at 22000kb/s, reviously at 4500kb/s). It had no effect on cd-rom drives.
I installed later version of IDE drivers (Siside47) but it had no effect on anything.
I have tried regroup my ide devices from connectors and from bios, no effect.
Any suggestions what could help?Quote
Originally posted by Napakettu
So, my problem is that my cpu´s cd-rom devices are extreme slow. SiSoft sandra benchmarks my DVD about 4000kb/s and my CDRW 2500kb/s.
I had same problem with my hardrive when i used IDE drivers from utility cd but when i installed new IDE driver from internet (Siside39?) i got my hd running good (at 22000kb/s, reviously at 4500kb/s). It had no effect on cd-rom drives.
I installed later version of IDE drivers (Siside47) but it had no effect on anything.
I have tried regroup my ide devices from connectors and from bios, no effect.
Any suggestions what could help?
i had a problem with a cd rom (52x) running at a crawl like 4x speed. still dont know why it did since it works fine in another system.
Nero has a program that measures your cd speed and a graph that shows you how it is going instead of a straight number like 2000. i think it is free to download -
Can you slow the scan rate of VI Logger scans per minute
Can you set up a logging task with VI Logger to log 1 scan per minute? I'm using a DaqCard AI-16E-4 and SCXI 1120 Module.
What do you mean by VI Logger? The easiest way to do what you need is to create a while loop and put in it one of NI's "easy-IO" analog input VIs and a wait function set to 60,000 milliseconds. Depending upon the acquisition VI you use the result would read either one point, or a set of predefined points once a minute. (see attached code)
How much more complicated the application would get depends on such things as what exactly you want to do with the data, and how you want the user interface to react. For example do you need to save the data? If so, you'll need to add a file save function to the loop too. Also, the simple version I attached could take as long as 2 minutes to quit once you press the stop button--which probibly wouldn't be acceptable.
The point is that the basic functionality you asked for is very easy to do. The complicated part is defining all the other stuff that wraps around that simple functionality.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps
Attachments:
daq_demo.vi 19 KB -
P965 NEO Slow IDE DVD/CD drive
Ok,
I've read some of the articles on problems with CD readers/writers not working or working very slow using this MOBO.
Here is my problem
I have a SATA hd that has my windows xp OS and it works fine. I installed it from the CD rom no problem.
The only problem I have is the CD/DVD rom appears to work very slowly in Windows.
****I am not running any raid devices.****
Should I have to install a JMICRO driver just to get my CD/DVD writer to function properly? I looked for a driver using the links I found in this forum but didn't find any. Im not sure if I even need one.
Has anyone solved this problem that isn't using Raid? I'd rather not install a driver if I do not need it.
Thanks,
JImQuote from: gungadin_ on 05-December-06, 04:42:30
After my current install is done I'm going to try this driver that remus suggests. As he had the identical problem I have. I tried that link above but it aimed at a 64bit driver? Not sure about that one if this doesnt work Illl try that one.
The problem is solved now (I had to waste enough time for that ...).
The solution: http://www.dieselbenz.info/JMB36X_WinDrv_Beta_R1.17.04.00.rar
It's a beta driver, but this is the answer to all "jMicron on MSI" bugs.
With that driver I was able to write a full CD at 48X and a full DVD at 8X without any error.
p.s.
A little piece of advice for MSI team:
The current v1.5 BIOS and jMicron driver are buggy (talking about MSI P965-Neo) !
You have to solve this problem as faster as you can because is very annoying and you'll lose customers !
Remus M
(an old MSI fan)
I was seriously bashing my head until I found your post. Even the drivers found on Live Update didn't work. These betas are the shiz. Thanks! -
Sorry to ask such a lame question but sometimes you overlook the obvious.
I have both sata drives set up as master on port 3/4 and Raid0.
Is that OK or should I set it up as Master/Slave or whatever.
I am now working on my 12th time installing Raid0 with XP.Drive 0
Model wd1200jd-00GBB0
Firmware 02.05D02
Drive 1
Model wd1200jd-00FYB0
Firmware 02.05D02
I give up.
I had no problems with these two drives on my ASUS A7NBX (Nvidia2) MB.
Raid0 was super fast using Silicon Image Drivers.
Again, thanks for the help.
PS
I tested these two drives with anything I can find, WD utilities, hdtach an so on and all results were good and practically identical. Do you know if there are other drivers I can try besides Nvidia? -
i am having trouble with a KT4 Ultra. Everything seems to be running so slowly. I build a new setup with it, but installing windows xp took 7 hours! I tried all the other components with a different mobo and it worked fine. This leads me to believe it's a faulty motherboard. Unless anyone else knows otherwise?
Hi,
Try clearing the CMos and only set the CPU-FSB right... -
Extremely slow IDE disk performance
Kernel 2.6.31.6
I'm absolutely sure the disk is not damaged.
The problem arose some time ago, probably after a kernel upgrade and it's very annoying. Desktop is nearly unusable when the disk is accessed and transferring data is a nightmare. Any suggestion? Thanks.
#hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 50 MB in 2.06 seconds = 24.26 MB/sec
Timing buffered disk reads: 6 MB in 3.28 seconds = 1.83 MB/sec
#hdparm -i /dev/sda
/dev/sda:
Model=Maxtor 6E040L0, FwRev=NAR61590, SerialNo=E13DDGHE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80293248
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 *udma1 udma2 udma3 udma4 udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-7 T13 1532D revision 0: ATA/ATAPI-1,2,3,4,5,6,7
* signifies the current active mode
#dmesg | grep ata
BIOS-e820: 0000000023ff3000 - 0000000024000000 (ACPI data)
modified: 0000000023ff3000 - 0000000024000000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
PERCPU: Embedded 14 pages at c19f9000, static data 34332 bytes
Memory: 576968k/589760k available (3111k kernel code, 12132k reserved, 1120k data, 416k init, 0k highmem)
.data : 0xc1309ddd - 0xc1421ea8 (1120 kB)
libata version 3.00 loaded.
pata_via 0000:00:07.1: version 0.3.4
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15
ata1.00: ATA-7: Maxtor 6E040L0, NAR61590, max UDMA/133
ata1.00: 80293248 sectors, multi 16: LBA
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
ata2.00: ATAPI: HL-DT-ST RW/DVD GCC-4480B, 1.03, max UDMA/33
ata2.00: configured for UDMA/33
ata1: drained 32768 bytes to clear DRQ.
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: BMDMA stat 0x25
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
ata1.00: status: { DRDY DRQ }
ata1: soft resetting link
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: limiting speed to UDMA/25:PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata1.00: BMDMA stat 0x25
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
ata1.00: status: { DRDY ERR }
ata1.00: error: { ICRC ABRT }
ata1: soft resetting link
ata1.00: configured for UDMA/25
ata1: EH complete
ata1.00: limiting speed to PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata1.00: BMDMA stat 0x25
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
ata1.00: status: { DRDY ERR }
ata1.00: error: { ICRC ABRT }
ata1: soft resetting link
ata1.00: configured for PIO4
ata1: EH complete
EXT4-fs (sda2): mounted filesystem with ordered data mode
EXT3-fs: mounted filesystem with writeback data mode.
EXT4-fs (sda3): mounted filesystem with ordered data mode
Last edited by Taylor001 (2009-12-23 10:12:44)I've had the same problem on multiple kernels as well... http://bbs.archlinux.org/viewtopic.php?id=83392
Does this always happen? For me it only occurs after I suspend. -
6500 scan option in solution center reacts extremely slow
Problem 1.It usually takes 5-8 mins for the scan window to show up after I press "scan to file" in solution center. This 6500 is extremely slow. I have had other hp all-in-one before and scanning has never been a problem. I don't know how I would solve this. So I started searching a scan option shortcut. No luck yet. Anyone knows where I can find the shortcut? Problem 2.Since it's so slow to scan from the solution center, I tried to do it from the panel. However, when I pressed the scan button, it showed "scan menu: select computer". Then I pressed "OK", it showed "no scan options".I have searched online and it seems like a popular problem. I have tried all the methods found online, but nothing worked. Thank you. I hope someone could help me on this. It's really frustrating.
Hi , Welcome to the HP Forums! I understand that you are having trouble scanning with your HP Officejet 6500, on Windows 7. I am happy to look into this scanning issue for you! To make sure I know the exact printer that you have, what is your printer's Product/Model Number? (ie: HP Officejet 6500 e710a, etc.) To find your printer's Product/Model Number follow instructions in this link. Finding Your HP Product Model Number. To verify the printer's hardware is functional, are you able to make copies with the printer? In the meantime, I would recommend to try our HP Print and Scan Doctor, and let me know what happens! Hope to hear from you soon! “Please click the Thumbs up icon below to thank me for responding.”
-
HP Scan Applicatio​n has stopped working Windows 7 64bit
The HP Scan 3.5 works better - it will scan pictures but the program must restart after each scan. Also the scans are really slow, other scanning programs work fine, Microsoft Live Photo Gallery and Picasa 3 in particular. I would prefer to use the HP program; it should take less steps to scan.
any ideas?
thanks
dan
Problem Event Name: APPCRASH
Application Name: hpiscnapp.exe
Application Version: 13.0.0.131
Application Timestamp: 4a0c0809
Fault Module Name: hpotiop5.dll
Fault Module Version: 100.0.272.0
Fault Module Timestamp: 47d1de66
Exception Code: c0000005
Exception Offset: 00041ef8
OS Version: 6.1.7600.2.0.0.256.48
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789Guys,
I am interested in this thread and would like to ask you to try the fix that is posted for the Scanned files disappearing as it installs a new version of the Scan software that may help with this problem.
The fix is posted here
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c01960605
Can you reply to this tread telling if this helped at all.
Thanks
JonW
I work for HP -
Zbot and other issues after sophos scan
bot-gal.ide zbot-gap.ide zbot-gay.ide zbot-gbf.ide
zbot-gbi.ide zbot-gbj.ide zbot-gbm.ide zbot-gbn.ide zbot-gbq.ide zbot-gby.ide zbot-gcb.ide zbot-gch.ide zbot-gcl.ide
zbot-gcm.ide zegos-cc.ide zeleff-a.ide
Scan name: "Scan Local Drives"
Scan items:
Configuration:
Scan inside archives and compressed files: Yes
Automatically clean up threats: No
Action on infected files: Report only
Live Protection enabled: Yes
Scan started at 2013-08-29 13:57:24 +0200
New volume detected at /
2013-08-29 14:11:06 +0200 Encrypted file: /Users/Downloads/AdobeFlashPlayerInstaller_11_ltrosxd_aaa_aih-1.dmg
2013-08-29 14:11:06 +0200 Encrypted file: /Users/Downloads/AdobeFlashPlayerInstaller_11_ltrosxd_aaa_aih-2.dmg
2013-08-29 14:11:06 +0200 Encrypted file: /Users/Downloads/AdobeFlashPlayerInstaller_11_ltrosxd_aaa_aih.dmg
Scan completed at 2013-08-29 14:13:08 +0200.
308531 items scanned, 0 threats detected, 3 issuesI don't know how you got rid of Sophos, but here are directions to make sure you got all related files.
Sophos Uninstaller
Maybe you are looking for
-
HT4528 how do I delete all my photos from my phone
How do I delete all my photos from my phone using my phone?
-
How do web site created with After Effect differ from that created with dream weaver or Flash?
As I have some experiance not much in After Effect..I have created my website in After Effect., I have no knowledge of Dream weaver or Flash.. My web pages take too much time to open., due to it loads SHOCK WAVE and it take much longer time., were
-
How to get reference of application component in anothor component?
Hello Friends I have one problem so plz help me. Thanks in advance. I have two file one is application and other is component. I have created Dividedbox in application and i put two buttons in component and used component in application. Now i want t
-
Running iTunes on my computer with my iTouch
So I've got a computer hooked up to my stereo and the iTunes files there are full lossless so I'd like to listen to that rather then the compressed sounds that are on my iTouch when I'm home. And I'd like to control it from the iTouch since the compu
-
Script Logic taking a lot of time to execute
Hi, I have a script logic which does the currency translation But it takes a lot of time to execute the same. can anyone suggest me to write a effective script logic to reduce the performance . I am using the input schedule that uses the script lo