Slow loading of User Menu While Logon

Hi,
I have created a new role with customized user menu. After assigning this role to my users, they start complaining about a very slow login to SAP as well as when opening a new session!
Any hits would be greatly appreciated ..
Sheikh

Dear Sheikh,
To confirm the issue, use transaction STAD and filter by response time of the users - does it fit to the times which they experience? If the users experience higher than the STAD response time, then it could be a browser side issue (or network issue) which somehow ovelapped with the change of role, but is not related to the change of roles.
If STAD time is high, then look at the CPU time and DB Time - take ST30 and ST05 traces to narrow down the issue. Is it possible that you activated Authentication trace on the ABAP server and then did not switch it back?
Best Regards,
Sylvia

Similar Messages

Intermittently slow load times from iTunes, while Netflix

TV shows from iTunes sometimes take a long time to load, while content from Netflix & Hulu seem fine. Why does iTunes sometimen indicate that it may take over an hour to load a 45min TV show?

Netflix/Hulu adapts to the connection in order to stream instantly. iTunes content is fixed and will start once enough has loaded. The time it takes is dependent on your network.
720P requires minimum 6mbps for instant stream
1080p needs 8mbps
Check speedtest.net to verify
Interference can also play a role, check istumbler or netstumbler to verify
Male sure you are on your ISPs DNS (settings - network - configure DNS - automatic)

Yosemite slow load and display changes at logon screen

Hi
I updated my Macbook Pro to Yosemite; since then at logon the display scale is bigger than my default, but once logged on the display changes smaller to my default.
At the logon I find that it takes longer to load after entering password etc; status bar rolls and taking about 30 seconds (instead of the 5 seconds previously in Mavericks).
Also find that after logon, it takes a few minutes to connect to the internet and be ready to use.
This never happened previously, was instant after logon could go straight into email or safari and work.
Is others experiencing this and what can I do to improve this?
Thanks

Hi
I updated my Macbook Pro to Yosemite; since then at logon the display scale is bigger than my default, but once logged on the display changes smaller to my default.
At the logon I find that it takes longer to load after entering password etc; status bar rolls and taking about 30 seconds (instead of the 5 seconds previously in Mavericks).
Also find that after logon, it takes a few minutes to connect to the internet and be ready to use.
This never happened previously, was instant after logon could go straight into email or safari and work.
Is others experiencing this and what can I do to improve this?
Thanks

Howto Refresh SAP BW Query Changes for roles (User menu)

Hi All,
I have apply new changes for combine hierarchy. However I have tested in Query Designer/web and its works ok hence the user cant see the change.
Howto Refresh SAP BW Query Changes for roles (User menu)
Below is the setup we do have (sap bw 3.5)
1. User run query from User menu (They logon to bw backend and run query by click on the icon on thier user menu.
Changes.
1.Apply combine hierarchy (Rows in Query Designer)
2. I have display query on the web and its work as expect
Issue
1. Query not refresh in user menu (Roles) Users run the query through user menu
Regards Jon

thank you

Activate User Menu in SAP logon screen

1. Configure individual specific SAP user
Enter transaction code SM30 (Maintain Table Views) in your SAP command field and maintain USERS_SSM table. You would notice that no data maintained in this table during initial access. To maintain entries, click u2018New Entriesu2019 button. Enter the individual username on the User Name field. To enable user menu and SAP menu, tick the appropriate checkboxes. To disable, untick the chekcboxes.
2. Configure all SAP user
Enter transaction code SM30 (Maintain Table Views) in your SAP command field and maintain SSM_CUST table. To enable te user menu for all SAP users set ALL_USER_MENUS_OFF = No. To disable it, set ALL_USER_MENUS_OFF = Yes.
To enable the SAP Menu set SAP_MENU_OFF = No, to disable it set SAP_MENU_OFF = Yes.

It is not a question, it is a tarot card
@ Arindam Banerjee: Feel free to post you findings if they are interesting or "common mistakes", but please only use this thread. Ideally this is stuff for the wiki - if not already in help.sap.com or the system itself...
Specifically in this case, user menus is no easy task in the wild and is very dependent on how you build your roles.
Cheers,
Julius

Dump while accessing Menu- User menu MESSAGE_TYPE_X

In the SAP initial screen under the user menu(Menu->User menu->General user transactions), when I am having a big number of tree sturcture under a specific folder like under 'General user transactions', I am getting dump with message MESSAGE_TYPE_X, AC_SYSTEM_FLUSH. This is happening, when lots of transactions are attached under any folder like 'General user transactions'. How to solve this. I am getting error in ECC6.0

Hi Sanjay,
1. reduce the number of transactions in one folder. Create more folders.
2. Ask your basis if it is because of memory issue?
3. Check in OSS if there is any specific note on the restrictions on the number of entries in the folder.
Regards,
Atish

Load Balancing Users

Hi Everyone,
We seem to have an issue on our load balancing where one server keeps getting overloaded with users on it than the other servers which is in turn causing performance issues where one server is getting over utilized while the others aren't. Other than limiting the amount of users that can log on to this one server is there anything we can do to balance out the users amongst the application servers?

Check the following SAP Notes:
[SAPNote 51789 - Poor user distribution in logon distribution|https://websmp230.sap-ag.de/sap%28bD1lbiZjPTAwMQ==%29/bc/bsp/spn/sapnotes/index2.htm?numm=51789]
[SAPNote 118093 - Concepts of defining 'limits' in logon load balancing |https://websmp230.sap-ag.de/sap%28bD1lbiZjPTAwMQ==%29/bc/bsp/spn/sapnotes/index2.htm?numm=51789]
[SAP Note 26317 - Set up for LOGON group for autom. load balancing|https://websmp207.sap-ag.de/~form/handler?_APP=01100107900000000342&_EVENT=REDIR&_NNUM=26317]
Thanks,
Naveed

Windows 2012 RDP "resets" user settings while using Roaming Profiles

Last month we installed a RDP environment running a Windows 2012 DC and 2 Windows 2012 RDP servers. The RDP servers are running in a pool.
For the rest it's nothing fancy.
The problem is that user-settings are reset, most likely during logon. This only occurs when we use Roaming Profiles.
- We create a new user, in a container with no GPO's attached.
- This user gets a RP while logging on, no errors, at logoff the RP is written to it's correct folder.
- Logging on again. Now for example I make Chrome standard browser and change the program which opens JPG files.
- Logging off
- I check the NTUSER.DAT in the RP folder and the changes I made can be found in the file. So it has been saved to the NTUSER.DAT.
- Now I login again and check the settings I made. IE is standard browser again and the JPG setting is also back to standard.
- Logging off
- Checking the NTUSER.DAT in the RP folder and yes, everything is back to default.
Now the funny part is, when I create a user with a local profile, everything is working properly. Settings been saved.
It doesn't make a different what kind of user it is. Domain User, Domain Admin. They all have the same problems when using RP's.
No error messages in the Event Viewer.
I'm clearly unable to solve this problem. Hoping someone can help me on this one.
What makes the settings reset at logon while using Roaming Profiles?
Thanks!

Hi,
Thank you for posting in Windows Server Forum.
Have you enable Cache copies option of roaming profiles?
This issue might occurs because the User Profile service does not load the terminal server roaming profile correctly after the user account password is reset.
When the Delete cache copies of roaming profiles Group Policy setting is enabled, and when a user is prompted to change the user account password, the User Profile service loads a local temporary user profile. The User Profile service loads this user profile
to perform the password reset operation. However, the profile changes to a combination of the local temporary profile and of the roaming profile after the user password is reset. Therefore, the terminal server roaming profile is not loaded correctly.
In addition, please try to delete the SID of the user from registry key and check the result. You can follow the below path.
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
More information:
You receive a "The User Profile Service failed the logon” error message
http://support.microsoft.com/kb/947215/en-us
Also check “User Profiles on Windows Server 2008 R2 Remote Desktop Services” article.
Hope it helps!
Thanks.
Dharmesh Solanki

Reader Slow Loading?

Hi,
Since getting Safari 5.0.1 with Reader, it seems Safari is much slower loading pages now.
I'm not certain that it is reader slowing page loading but going to the same sites in Firefox and other browsers the pages load much faster.
I'll open a page in Safari, say CNN, and it takes so much longer to load now and it looks like the page will not open until Reader has done it's job.
Any suggestions?
Thank you.

Hi,
Empty your Safari cache more often. From your Safari Menu Bar click Safari/Empty Cache.
Web pages include a small icon or 'favicon' which is visible in the address bar and next to bookmarks. *These icons take up disk space and slow Safari down.* It is possible to erase the icons from your computer and start fresh.
*To delete Safari's icon using the Finder, open your user folder, navigate to ~/Library/Safari/ and move this file "webpageIcons.db to the Trash.*
Carolyn

HT5559 slow loading and loading in sections

Start up began last week with a gray slow screen - past two days 13" mac is slow loading and loading in sections of white blocks on my screen - is it JAVA? What to do? It happens if I walk away for a short time, if it goes into screen saver and or if I put lid down - Got 13 " alumn case with Mtn Lion September 2012.

Go step by step by step and test.
1. Power off the router. Unplug it from the wall. Wait a while.
    Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
    Restart the computer.
    Start up in Safe Mode.
    http://support.apple.com/kb/PH14204
2. Delete Caches.db
    Close all windows and quit all applications.
    Hold "option" key down and click "Go" menu in the Finder menu bar.
    Select "Library" from the dropdown.
    Library > Caches > com.apple.Safari > Caches.db
    Right click the Caches.db file and select "Move To Trash.
    Close windows and relaunch Safari.
3. Empty Caches
    Safari > Preference > Advanced
    Checkmark the box for "Show Develop menu in menu bar".
    Develop menu will appear in the Safari menu bar.
    Click Develop and select "Empty Caches" from the dropdown.
4. Delete Cookies
    Safari > Preferences > Privacy > Cookies and other website data:
    Click the “Details” button.
    Remove all cookies except from Apple, your internet service provider and banks.
5. Safari > Preferences > Extensions
    Turn off Extensions if any and launch Safari again to test.
    Turn on those one by one and test.
6. Update Adobe Flash Player.
     http://get.adobe.com/flashplayer/
7. Deselect Proxies if selected.
    System Preference > Network > Advanced > Proxies Tab
    Under "Select Protocol", uncheck any box if selected.
    Click "OK" then "Apply”.
8. if this doesn't help, do an EtreCheck and post the report here please.
     EtreCheck: https://discussions.apple.com/docs/DOC-6173

Random, excruciatingly slow load time with 7900 Elite small form factor desktops

Hi all, I have approx 300 HP 7900 Elite small form factor machines in my environment that were deployed just over two years ago. from the time of deployment we have experienced on about 50 occasions a random, excruciatingly slow load time that take about one hour for the user to login and open their programs. there has been no rhyme or reason for it, different floors, areas of the building, etc. I searched the forum for similar probs and didn't see one like this, I hope I'm not duplicating efforts from someone else's question... One thing we have noticed is that if we re-boot while it is going through the start-up process, it seems to "make it angry" and will lengthen the overall load time. We use the 32-bit Vista Enterprise OS. This is with a "stock" build, that is to say, our standard corporate build. our security policy does not allow users to install software, by the way. Thanks so much if you can help!

Hi,
How is the issue going? Usually, this error can be caused by missing third-party NIC driver. To solve the issue, we can download the missing network
driver and update the WDS boot image to include it.
In addition to the article provided by Chris, the following blog can also be referred to as reference.
http://askmetricks.blogspot.in/2013/03/solvedwdsclient-error-occurred-while.html
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this
information.
Best regards,
Frank Shen

I just updated my RAM and I keep getting a crash report. I have a 21.5 Inch mid 2010 imac. I also am experiencing slow load times and when I try to open Final Cut it says that quartz extreme is not compatible and that I have no VRAM even though I do.

I just updated my RAM (replaced the two 2 gig cards with two Corsair 8 gig cards) and I keep getting a crash report. I have a 21.5 Inch mid 2010 imac. I also am experiencing slow load times with Photoshop and when I try to open Final Cut it says that quartz extreme is not compatible and that I have no VRAM even though I do.
Here is the crash report:
Interval Since Last Panic Report: 5426204 sec
Panics Since Last Report:          2
Anonymous UUID:                    2DD57DDB-BB42-5614-395A-CA6225BDAFD9
Wed Mar 20 11:36:53 2013
panic(cpu 0 caller 0xffffff801aa43d8e): "a freed zone element has been modified in zone: maps"@/SourceCache/xnu/xnu-2050.18.24/osfmk/kern/zalloc.c:219
Backtrace (CPU 0), Frame : Return Address
0xffffff81eb0eb950 : 0xffffff801aa1d626
0xffffff81eb0eb9c0 : 0xffffff801aa43d8e
0xffffff81eb0eba00 : 0xffffff801aa435d2
0xffffff81eb0ebae0 : 0xffffff801aa663f7
0xffffff81eb0ebb20 : 0xffffff801aa67398
0xffffff81eb0ebc70 : 0xffffff801aa6887c
0xffffff81eb0ebd20 : 0xffffff801ad5b8fe
0xffffff81eb0ebf50 : 0xffffff801ade182a
0xffffff81eb0ebfb0 : 0xffffff801aaced33
BSD process name corresponding to current thread: launchd
Mac OS version:
Not yet set
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
Kernel slide:     0x000000001a800000
Kernel text base: 0xffffff801aa00000
System model name: iMac11,2 (Mac-F2238AC8)
System uptime in nanoseconds: 1070542822
last loaded kext at 707348380: com.apple.driver.AppleIRController    320.15 (addr 0xffffff7f9c53e000, size 28672)
loaded kexts:
at.obdev.nke.LittleSnitch    3908
com.apple.driver.AppleIRController    320.15
com.apple.driver.AppleUSBCardReader    3.1.0
com.apple.driver.AppleFileSystemDriver    3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless    1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
com.apple.BootCache    34
com.apple.iokit.SCSITaskUserClient    3.5.1
com.apple.driver.XsanFilter    404
com.apple.iokit.IOAHCIBlockStorage    2.2.2
com.apple.driver.AppleUSBHub    5.2.5
com.apple.driver.AppleFWOHCI    4.9.6
com.apple.driver.AirPort.Atheros40    600.70.23
com.apple.driver.AppleUSBEHCI    5.4.0
com.apple.driver.AppleAHCIPort    2.4.1
com.apple.iokit.AppleBCM5701Ethernet    3.2.5b3
com.apple.driver.AppleUSBUHCI    5.2.5
com.apple.driver.AppleEFINVRAM    1.6.1
com.apple.driver.AppleACPIButtons    1.6
com.apple.driver.AppleRTC    1.5
com.apple.driver.AppleHPET    1.7
com.apple.driver.AppleSMBIOS    1.9
com.apple.driver.AppleACPIEC    1.6
com.apple.driver.AppleAPIC    1.6
com.apple.driver.AppleIntelCPUPowerManagementClient    196.0.0
com.apple.nke.applicationfirewall    4.0.39
com.apple.security.quarantine    2
com.apple.driver.AppleIntelCPUPowerManagement    196.0.0
com.apple.iokit.IOUSBHIDDriver    5.2.5
com.apple.iokit.IOSCSIBlockCommandsDevice    3.5.1
com.apple.iokit.IOUSBMassStorageClass    3.5.0
com.apple.driver.AppleUSBMergeNub    5.2.5
com.apple.driver.AppleUSBComposite    5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice    3.5.1
com.apple.iokit.IOBDStorageFamily    1.7
com.apple.iokit.IODVDStorageFamily    1.7.1
com.apple.iokit.IOCDStorageFamily    1.7.1
com.apple.iokit.IOAHCISerialATAPI    2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily    3.5.1
com.apple.iokit.IOUSBUserClient    5.2.5
com.apple.iokit.IOFireWireFamily    4.5.5
com.apple.iokit.IO80211Family    500.15
com.apple.iokit.IOAHCIFamily    2.2.1
com.apple.iokit.IOEthernetAVBController    1.0.2b1
com.apple.iokit.IONetworkingFamily    3.0
com.apple.iokit.IOUSBFamily    5.4.0
com.apple.driver.AppleEFIRuntime    1.6.1
com.apple.iokit.IOHIDFamily    1.8.0
com.apple.iokit.IOSMBusFamily    1.1
com.apple.security.sandbox    220
com.apple.kext.AppleMatch    1.0.0d1
com.apple.security.TMSafetyNet    7
com.apple.driver.DiskImages    344
com.apple.iokit.IOStorageFamily    1.8
com.apple.driver.AppleKeyStore    28.21
com.apple.driver.AppleACPIPlatform    1.6
com.apple.iokit.IOPCIFamily    2.7.2
com.apple.iokit.IOACPIFamily    1.4
com.apple.kec.corecrypto    1.0
Model: iMac11,2, BootROM IM112.0057.B00, 2 processors, Intel Core i3, 3.2 GHz, 16 GB, SMC 1.64f5
Graphics: ATI Radeon HD 5670, ATI Radeon HD 5670, PCIe, 512 MB
Memory Module: BANK 0/DIMM1, 8 GB, DDR3, 1333 MHz, 0x029E, 0x434D5341384758334D314131333333433920
Memory Module: BANK 1/DIMM1, 8 GB, DDR3, 1333 MHz, 0x029E, 0x434D5341384758334D314131333333433920
AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x8F), Atheros 9280: 4.0.70.23-P2P
Bluetooth: Version 4.0.9f33 10885, 2 service, 18 devices, 0 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: ST31000528AS, 1 TB
Serial ATA Device: HL-DT-STDVDRW GA32N
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfd100000 / 2
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 4
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd110000 / 3
USB Device: hub_device, 0x0424 (SMSC), 0x2514, 0xfa100000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000 / 4
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0xfa111000 / 6
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfa120000 / 3

There have been a few reports on here where Corsair RAM seems to have caused users a lot of grief with crashes.
The recommendation on here, mostly, is to only buy RAM from macsales.com or crucial.com as they guarantee their modules will work and offer a no quibble lifetime guarantee.
I'd put the original RAM back in, return the Corsair chips for a refund and re-order from one of those two companies.
http://eshop.macsales.com/shop/apple/memory/iMac
http://www.crucial.com/

Windows cannot load the user's profile but has logged you on with the default profile for the system.

My Windows 7 crashed a couple days ago after a windows update, I got this message.
Windows cannot find the local profile and is logging you on with a temporary profile. Changes you make to this profile will be lost when you log off.
I restarted the machine and got this message
Windows was unable to load the registry. This problem is often caused by insufficient memory or insufficient security rights.
DETAIL - The process cannot access the file because it is being used by another process. for C:\Users\TEMP\ntuser.dat
I checked the event Log I found these .
Windows cannot load the user's profile but has logged you on with the default profile for the system.
DETAIL - Only part of a ReadProcessMemory or WriteProcessMemory request was completed.
Windows has backed up this user profile. Windows will automatically try to use the backup profile the next time this user logs on.
Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile.
DETAIL - The process cannot access the file because it is being used by another process.
This is the first error in the event viewer after a successful logon
The description for Event ID 34 from source ccSvcHst cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
ccSetMgr
Windows cannot load the user's profile but has logged you on with the default profile for the system.
DETAIL - Access is denied.
Looking at the Logs all I can tell is that after the Desktop Window Manager started if caused this error.
The winlogon notification subscriber <SessionEnv> was unavailable to handle a notification event.
then this one
The Desktop Window Manager has exited with code (0x40010004)
Then this before it shutdown.
The User Profile Service has stopped.
I started up the PC and the first message I got was
How can I get access to my user profile? do I need to createa new Administrator account? Please help
The EventSystem sub system is suppressing duplicate event log entries for a duration of 86400 seconds. The suppression timeout can be controlled by a REG_DWORD value named SuppressDuplicateDuration under the following registry key: HKLM\Software\Microsoft\EventSystem\EventLog.

hi do the following
1. In Search programs and files (Windows 7) area, type in regedit, and press Enter.
2. If prompted click yes,
3. expand the following HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
4. click the sid that related to your admin profile (if you not sure, click each sid and in turn look to the right hand side of registry editor it will show who that sid is related to one of the registry files should hae in description localhost\admin or
something similair)
5. right click the sid and press delete.
6. restart your machine and log back on with the admin account, this will then rebuild the admin profile... dont worry when it loads and none of your personal settings are saved or files or folders... go to c:\users
in here you will see two folders for the admin account, one will be just admin and the other most likely admin.localhost
i cant remember which one is which but just check both, one will still have all your files and folders in it.
i suggest making a backup of your data before doing this incase something does go wrong, but ive had this happen many times in a domain enviorment and has worked for me everytime.

Understanding the User Menu in XI

hi,
I am pretty new to XI (as you can probably tell by few queries i have posted).
When you log in to your XI SAP system, the system essentially displays a "User Menu", which includes many folder with different options for monitoring, sld, runtime settings, configuration,...etc.
Just curious to find out what each of the options on the user menu does and more so when would you actually use those options. Have tried to click on some of the options and get familiar with them. But is there a more specific document provided by SAP that explains each functionality (besides maybe the documentation help).
Also speaking as a beginner, what is a good strategy to get more acquainted and understand XI? Your thoughts would be appreciated.
Regards,
Manpreet

Hi,
Apart from help.sap.com, u have very good Articles in the articles section which will speak about Design, configurations, Adapters, Runtime and all u need in different pdf files and ppts. all u need to do is go to Articles section and serch for the Right document that u need. ( i cannot mention all the pdf file names here.. it will fill the whole page ).
also when u go to XI home page, u will find
e-learning link on the righthand side. Listen to the Beginners section.This will also help u a lot.
While creating scenario's u can look at the weblogs section of XI. and its a knowledge repository ( help.sap.com made simpler )
all the above mention links help u in understanding XI better. But u should start working on
1) simple File to File
2) File to DB and other simple scenario's to really get how things work in XI.
The best part is u already have weblogs (step-by-step procedure ) mentioning these.... )
For the rest u have XI forum )
Hope this helps you.
Cheers,
Siva Maranani.

Slow loading on website

I am new to Quicktime Pro, but have found it very easy to use with great quality results endoding my FC files for the web. My problem is that when a user clicks to open my video sample, the file has a very slow load time. Some specifics:
input file: 1.8 GB file exported from FCE as uncompressed 8-bit
output file: in QTPro - encoded with H.264, 15 fps, 100 key frame, 800 kbps, set for streaming (fast start), 640X480, deinterlacing checked. file size 8 MB.
As I said, the quality is great (except that the deinterlacing filter doesn't seem to do anything), but the playback outpaces the load very quickly. It takes almost 2-3 minutes for the file to be ready to start automatically. I've been told that an 800 kbps file should load in a few seconds.
Is there anything you could tell me to enhance the load time? I'm wondering if I'm missing a simple step since QT has been so easy to start to use.
Thanks so much for your help!! Jo

Nothing at all wrong with your QuickTime file but your html code at http://aftglow.com/ directly links to it rather than calling the quickTime browser plug-in.
That may be the source of your troubles. You need to use special html page code for QuickTime:
http://developer.apple.com/internet/ieembedprep.html

Slow loading of User Menu While Logon

Similar Messages

Maybe you are looking for