Slow Print and Print Setup command in Reader Ver. 8.1.2

Print and print setup command take over 30 seconds to load on Reader ver. 8.1.2. I tried ver 6 and same thing happens. Using the print shortcut and same thing happens.
System: New Dell computer (Windows XP Pro, SP2). Any advice would greatly be appreciated.

You are not alone. Same problem here on a brand new computer with 2GB of RAM. Three minutes total to print a small, black and white 1 bit, 15 page pdf file. Previous to 8.1.2 (8.1.1) the same version printer drivers (Xerox Phaser 8860 Series) worked fine (both PS and PCL versions). I've been trolling for a fix this morning - so far nothing.

Similar Messages

  • Why has my hp deskjet 2050 printer and scanner suddenly slowed down and printing one line at a time

    why has my hp deskjet 2050  printer and scanner suddenly slowed down and printing one line at a time

    This is usually indicative of a defective print cartridge.  Suspect the black is low in ink or defective.  Please check all cartridges. 
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • Slow spooling and printing from Powerpoint 2013

    Has anyone experienced slow spooling and printing of PowerPoint documents from PP 2013?
    If I attempt to print the same document from PP2010, it spools and prints normally. It seems that the document background has something to do with slowness.
    I saw an older KB where Microsoft suggested to disable background printing. Disabling background printing makes it even worse.
    Thanks
    here is a link to a PowerPoint file
    https://www.dropbox.com/s/hle8x32j6wemday/SLOW.pptx?dl=0

    Hi,
    Does this only happen with PowerPoint documents? What about other Office files? How many machines are affected by this issue?
    Please first check whether you have the same print settings in PowerPoint 2013 and 2010.
    Also, if this is a network printer, please try to add it as a local printer, then try again and see if issue persists.
    Regards,
    Ethan Hua
    Forum Support
    Come back and mark the replies as answers if they help and unmark them if they provide no help.
    If you have any feedback on our support, please click
    here

  • How do i set up the eprint from my blackberry so i can send emails to my printer and print them off

    how do i set up eprint on my blackberry so i can send emails from my phone to the printer and print off

     Hi Tanya_Carroll,
    You can follow this link to set up ePrint. 
    http://h71028.www7.hp.com/hho/us/en/ep/articles/setting-up-mobile-printing.html
    Once ePrint is setup, you can send an email to the printer's email address.
    Be sure to use one of these email clients when sending to the printer.  If the Blackberry will not send using your original email address, setup a new email account on the Blackberry and try again.
    Hotmail, Yahoo! Mail, Gmail
    BlackBerry mail clien
    Although I am an HP employee, I am speaking for myself and not for HP.
    If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

  • AirPlay won't recognize printer and print although HPprint app does

    My iPad will not print from AirPlay and shows no printer on my wifi network from AirPlay. However,  I can print from my HPprint app and the app recognizes my printer on my wifi network. Any suggestions to get AirPlay to recognize the printer and print?

    HP Photosmart C4795.
    Maybe not on the approved list even though the app recognizes it?

  • HT4356 I GOT AN EPSON WP-4533 WHICH HAS AIR PRINT AND PRINTS FROM MY MAC AND MAC BOOK W/O PROBLEMS, BUT WON'T PRINT FROM MY IPHONE.  IT IS NOT ON THE ABOVE LIST OF PRINTERS, BUT BOTH EPSON AND APPLE SAID IT WILL WORK.

    I GOT AN EPSON WP-4533 WHICH HAS AIR PRINT AND PRINTS FROM MY MAC AND MAC BOOK W/O PROBLEMS, BUT WON'T PRINT FROM MY IPHONE.  PROBABLY BECAUSE IT'S NEW IT'S NOT ON THE APPLE LIST OF PRINTERS, BUT BOTH EPSON AND APPLE SAID IT WILL WORK. ANY THOUGHTS

    Some things you can try.
    Startup Issues - Resolve
    Startup Issues - Resolve (2)

  • Can I hook up my ipad to a printer and print with it?

    I work in a rural area where we can only get satelite internet. We want to start printing orders here and I know there is an app for printing, however we do not have a wireless printer, Do we need to buy one or can I use the charging cord my Ipad came with and hook it up with the USB to my existing printer and print that way? Any help would be greatly appreciated!
    Tiffany

    You'll need a printer that is compatible to AirPrint, see this article:
    http://support.apple.com/kb/HT4356
    You can't use the cord to connect.
    There are apps inn the app store that let you print over the Internet, without having an AirPrint compatible printer.

  • How to fetch print and print preview variables

    hi everyone,
                          my requirement is as soon as sales order created. printout of that sales order will be taken at the same time email should be send to that particular customer.
    the problem is the email is sent as soon as we check the print preview itself.
    but the mail should be sent afte the pressing print button only.
    how to fetch print or print preview by program
    regards
    karthe

    Hi everyone,
    I have tried open form and close form
    The itcpp-tdspoolid eq '0' for both print and print preview.
    I have set the open form
    dialog = 'X'.
    have i got to set anything in open form.
    this is my open form and close form.
    CALL FUNCTION 'OPEN_FORM'
    EXPORTING
    DIALOG = 'X'
    IF SY-SUBRC <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
    WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    ENDIF.
    CALL FUNCTION 'CLOSE_FORM'
    IMPORTING
    RESULT = itcpp
    IF SY-SUBRC ne 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
    WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
    else.
    if itcpp-tdimmed eq 'X' and itcpp-TDSPOOLID ne ''.
    endif.
    regards
    karthe

  • All of a sudden Very Slow Printing and Print to PDF

    I am running OSX 10.4.11 on A G4. I was having no trouble printing to a HP2500. The time to print or print to a PDF was fast from all my applications. I am focusing on InDesign CS for this discussion. I changed recently to a HP 3600N and also to 10.4.11. Now it takes 1 hour to prepare a 28 page color document for printing. Once job is sent to the printer it takes about 3 minutes to actually print it. The slow rendering of the document also occurs when creating a PDF using the Print dialog. I tried the 2500 as a test and found the same problem. It appears that 10.4.11 is the culprit. I tried the same document on my iMac running an older OSX and I had no problem. I wish I had my back up drive still on 10.4.9 so I could check that out but alas I backed up and now have the 10.4.11 OS mirrored on that drive.
    I am out of business until I can resolve this problem.
    Eagerly awaiting advice!
    Dan

    Drive A is 60 GB with 3.66GB free.
    Running OSX from that drive should really slow it to a Crawl, and is getting to the dangerous point... you need at least 12GB fre, 30 GB would be better.
    Nt certain why the other is so slow... did you open Activity Monitor & observe CPU, Memory & such while it is slow?
    If you can free some space on the Internal, Might give a try with Applejack...
    http://www.versiontracker.com/dyn/moreinfo/macosx/19596
    After installing, reboot holding down CMD+s, then when the prompt shows, type in...
    applejack AUTO
    Then let it do all 5 of it's things.
    At least it'll eliminate some questions if it doesn't fix it.
    The 5 things it does are...
    Correct any Disk problems.
    Repair Permissions.
    Clear out Cache Files.
    Repair/check several plist files.
    Dump the VM files for a fresh start.

  • HP Series 1600 Printer and Printer setup utility

    I just purchased an HP 1600 printer
    and loaded the software
    When I go to add the printer in the Printer setup Utility
    the name shows up but it says that it can't find the drivers
    I have tried the fixamac software to try and fix the problem but that doesn't seem to be working either
    is there a work around that mac supports or should I just buy another Printer
    Thanks

    Thanks for the info regarding your OS.  And no need to apologize! 
    That's very odd that you do not see your printer listed in the Programs list (no - it would not be the HP Support Solutions Framework).  That leads me to believe your printer is not actually installed.  If it were, you should see something like this (note that I have more printers installed than a regular user )
    So...if you don't see your HP Photosmart C4180 listed here, then I would say to go ahead and try to install the full driver.  The instructions in my previous post would be the same, but since you have Windows 7, this would be the right document to help walk you through the steps.
    Thanks!
    Tara
    **Although I am an HP employee, I am speaking for myself and not for HP.

  • Using epson 400 air printer have 4th gen ipad was able to find printer and print now unable to find air printer never worked right away  but now all I get is notorious printer says wifi setup ok restarted ipad  this and that no air printers found do not g

    I am using a 4th gen ipad with an epson Xp400 air printer my ipad was able to find printer but now it cannot. Printer says wifi setup ok. Do not understand why it can't find printer. Never did work right away always have to restart ipad or do wifi setup again on the printer. I am not sure whether os is ..1 or.2 or just 6.0

    bump...   Anyone have any answers?  

  • Printer and printer-scanner isn't recognised by Acrobat 7.1 Professional, though it is by Reader

    I'm running Acrobat 7.1 Professional with latest updates, on a WinXP system (SP3). Printer-scanner is a Brother 420CN and a laser printer HL 2040. Neither is recognised by Acrobat, although I can print to them from Reader (latest version) and any other program. This failure to recognise printer occurred failry recently, possibly after a recent update to Acrobat? I've tried "Detect and repair", but it appears to not run. (A dialogue screen flashes and disappears too fast to read) I've reinstalled Acrobat using the msi file in the Acrobat folder. Nothing has made any diference - still no printer!
    In print set-up or print, a dialogue box asks "Before you can perform printer related taks, such as print set-up or printing a document, you need to install a printer. Do you want to install a printer now?". On selecting "Yes" another box opens stating that "Operation could not be completed. The print spooler service is not running" However on checking component services, print spooler is running! I've checked this both before and after going through this dialogue.
    I was unable to reinstall Acrobat over the present installation using the opriginal CD as it recognised the installed (and updated) Acrobat as being of a later version than the version on the CD, and I didn't want to uninstall and then reinstall as I wanted to keep the document history. (Is history in a file that I can copy and keep during an install, or is it not deleted during uninstall?)
    Has anyone else faced and solved this printing problem? Has anyone any suggestions?
    Thanks in advance for your advice

    If you are using a Windows based computer, follow the instructions for resetting the AMDS >  How to restart the Apple Mobile Device Service (AMDS) on Windows
    Reset the AMDS then see if the battery will charge while the iPhone is on.
    If not, try a reset.
    Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
    If that doesn't help, tap Settings > General > Reset > Reset All Settings
    No data is lost due to a reset.

  • I can't scan a document in my printer and have it open in Reader like before

    can't scan a document in my printer and have it come up in the adobe acrobat reader like it did before my last update...can anyopne suggest a solution...have been on hold with adobe for 46 minutes.

    Hi lostinma,
    Are you scanning and then saving to PDF with your scanning software? What happens when you try to open the PDF in Reader? Do you get an error message?
    Reader doesn't allow you to create PDFs, so you wouldn't be able to scan directly into Reader.
    Best,
    Sara

  • Bran New to Mac - Printer and Printer Setup Question

    I am very new to Macs, and I'm getting a Macbook Pro when Leopard comes out.
    Would I need a certain printer for the laptop and a certain connector that I would need to buy seperatly for it?
    -Shaun

    Hi Shaun
    Congratulations on the Macbook Pro!
    Almost every modern printer will work just fine with the laptop. Most commonly, you would get one with a USB connection, which will attach directly to the laptop. Such a printer could also connect to an Airport Extreme/Express, and then you could print wirelessly. Make sure that the printer comes with a USB cable, or buy one - it'll likely have a "square" USB connection for the printer, and a "flat" connection for the Macbook's USB port.
    Some printers also have network connections, so they can attach to a network device (like a router) and the Macbook would be able to discover and print to it, but this is more common with larger printers such as office laserjets.
    Matt

  • Updation of table after Print and Print-Preview in smartform

    Hi,
    I am having a requirement where i need to print multiple deliveries with the sales order data each delivery on a new page using smartform.
    Now , i am using SSF_OPEN, SSF_CLOSE Fm's for the same. I need to update a Z table after the user clicks on PRINT from the pop-up or print from the print preview screen.
    I tried using the output_info parameter in the smartform where i read from a post that the OUTPUTDONE parameter becomes "X" in the job_output_info when the user clicks print wither in the two ways said before.
    This does not work out in case if the FM'S SSF_OPEN and SSF_CLOSE are used.
    Kindly help me on the same.
    Thanks in advance

    yes i tried that..using the AT new event for a Delivery and then a command to go to the NEW PAGE, but somehow when i execuet the form, i could not see the layout..so in the debug i saw the subrc after the FM is run..it says SUBRC = 2 i.e. internal error. I am not able to figure that out.
    So i had to use these open and close, nowi just want to update a z table if the user clicks on the print button (print preview screen) after using the print preview .
    Kindly suggest.
    Thanks.

Maybe you are looking for