Slow printing on windows 2008 std, R2 and windows 2012

Hi All,
I have a print server which is configured on windows 2008 R2. We are experiencing slow printing when printing directly from the server or from a client through the server. Small sized files prints fast, anything which has image takes a long time. All the
printers in our organization are Xerox Colorqube 9303. When installed the driver directly on to windows 7 32 bit PC, it prints without any delay. Also, when prints from the server a 2 MB file becomes 15 MB or more while sending. We have tried PCL6 and PS drivers.
To replicate it, i have installed a windows 2012 server ended up with the same result. Installed windows 2008 standard 32 bit with SP2 and the result remains same. Also tried it on windows 8, 64 bit without any luck. So effectively, it works fine only when
directly installed on a windows 7 PC. I have disabled all three: disabling TCP Chimney Offload, RSS, Receive Window Auto-Tuning .
After shooting the print, if you observe the printer properties, it sends data at a very low rate which results a 10 MB documents prints take around 10 minutes. At the same time, file copying from the server to and fro is working normally. All these servers
are directly connected to the cisco 6509 core switch. All the above tests were performed on the same physical switch. The server and clients are on the same network (subnet).
Have anybody come across to a similar issue. Any useful suggestions would deeply appreciated.
Thanks,
Prince Mathew

Hi Prince Mathew,
Based on your description, this issue seems that it’s related to this specific model printer (Xerox
colorqube 9303). Please install the latest version of the driver and the firmware from Xerox website, and then check if this issue still exists.
If it still persists, please clear Printer Spooler Files and enable the Spooler Service again.
For details, please refer to.
1. Click Start, run "Services.msc" (without the quotation marks).
2. In Services list, please double click "Printer Spooler". Then click
Stop, and then click OK.
3. Please locate to: "%WINDIR%\system32\spool\printers", delete all files in this folder.
4. Click Start, run "Services.msc" (without the quotation marks). In Services list, double click
"Printer Spooler". Click on Start. In the Startup Type list, make sure that "Automatic" is selected and click OK.
Then check if this issue can be solved.
Hope this helps.
Best regards,
Justin Gu

Similar Messages

Can we run domain controller windows 2008 32 bit and additional domain controller on 2003 server

im my environment we are trying to upgrade from server 2k3 to 2k8, out testing done on server 2k3 to 2k8, but can we run domain controller windows 2008 32 bit and additional domain controller on 2003 server ...kindly suggest
Nitin Gaurav
[email protected]

Yes you can. If you have two 2003 AD servers currently and upgrade one of them to 2008 AD then they'll continue to be able to work together. The domains functional level will remain as 2003 across both servers so at this stage you won't get any benefit from
the new AD functionality available in 2008.
Once you've then upgraded the second 2003 server to 2008 you can then upgrade the functionality levels in AD to make it 2008. It's been a while, but I believe it doesn't happen automatically, so once all AD servers have been upgraded you have to go into
AD and upgrade the functionality levels yourself.

FIM 2010 R2 Sp1, Windows 2008 R2 SP1 and Recycle Bin issues

Hi,
We are running FIM 2010 R2 Sp1 (build 4.1.3613.0)
Also running Windows 2008 R2 Forest and Domain functional level environment. (Windows Server 2008 R2 SP1 on all DCs). The previous Recycle Bin hotfix https://support.microsoft.com/en-us/kb/979214/ fails to install since we are already running WS08 R2 SP1
on all the DCs.
During deprovisioning, when a user is deleted from the source HR system, FIM deletes the object from AD, FIM Sync & Portal.
FIM also manages a FIM Portal group, where membership is assigned manually. This membership is then updated in AD.
When a user (who is part of this group) is deleted in HR, FIM deletes it from AD, FIM Sync, FIM Portal, FIM also removes user from FIM Portal group. The user is also removed from the AD group (by FIM group object membership attribute flow to AD)
...however, on the next AD Export, FIM fails to update the same group and complains about this very same user (CD Error) and lists the user as: CN=username\0ADEL:GUID, CN=Deleted Objects,DC=domain,DC=com
It appears that there is a problem with FIM and the Recycle Bin again?
Are there any new Recycle Bin/FIM hotfixes ?
Thanks,
SK

May I suggest you review the following:
Is the AD MA user account part of the Domain Admins group? If yes, please remove it from this Group
Verify that the "CN=Deleted Objects" container has not somehow been included in the AD MA OU scope

Internet Explorer Security Support on Windows 7 & WIndows 2008 Std Server

I have an app page (tomcat https) that i was able to open from a windows 7 professional remotely but could not open from a windows 2008 std server. Is there a security settings I need to disable from windows 2008 std server? The firewall is disabled.
Both Win 7 & 2008 is on the same network.
Thanks in advance.
DT

Hi,
I need the error information from the Internet Explorer, if the error code is 404 that should be the webpage is not correctly developed, error code 500 means the tomcat server is not available, you should check the tomcat server, or another situation is
the port number is in use by another application, normally the default port number is 8080, you can try another port number in the comcat configuration file to see the result.
Regards
Wade Liu
TechNet Community Support

WIndows 7 and Windows 2008 authentication failed in Windows 2003 Domain

Hi,
We have Domain with Windows 2003 and recently Windows 2008 Doamin controllers also added.
We are facing authentication failure for Windows 7 and Windows 2008 Domain members when user is trying to login.
Schema Master is on Windows 2003 and remaining roles on Windows 2008 Domain controller.
Windows XP clients login is working fine.
Problem si for Windows 7 and Windows 2008 Domain members login.
Any hint/solution will be really great help.
Pls share if you have any solutions.
Regards:Mahesh

Hi,
I found some more details about issue
Below are the events getting generated. It looks like due to encryption mismatch with Windows 2003 Domain and Windows7 and Windows 2008 clients. However i am looking for solution if someone tested this case.
Event Type:        Error
Event Source:    KDC
Event Category:                None
Event ID:              26
Date:                     08/06/2014
Time:                     9:41:04 AM
User:                     N/A
Computer:          AAAAAA
Description:
While processing an AS request for target service krbtgt, the account ADDADA$ did not have a suitable key for generating a Kerberos ticket (the missing key has an ID of 2). The requested etypes were 17. The accounts
available etypes were 23 -133 -128 3 -140.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Event Type:        Error
Event Source:    Kerberos
Event Category:                None
Event ID:              4
Date:                     08/06/2014
Time:                     9:34:17 AM
User:                     N/A
Computer:          AAAAAA
Description:
The kerberos client received a KRB_AP_ERR_MODIFIED error from the server ADADDFHDHDH$. The target name used was . This indicates that the password used to encrypt the kerberos service ticket is different than that on the
target server. Commonly, this is due to identically named machine accounts in the target realm (DOMAINNAME.COM), and the client realm.   Please contact your system administrator.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Regards:Mahesh

Windows 2008 STD DC Virtualization

Greetings Fellow Techies,
I have Virtualized a Windows 2008 DC Server using VMware vCenter tool. Once I open the
Server using VM Player on Ubuntu the Server boots up flawlessly but Active Directory do not
work. There is no point virtualizing the DC if the Active Directory is not working. The service
show it is working. Also I have found that Ethernet Driver & Base System Driver is not been
installed as well. When I Install Windows 2008 STD Server as Clean Install on the same
configuration everything is working fine.... How do I get all thiese corrected? Do I have to re-
Virtualize the Server with may be Active Directory Service stopped etc etc... your suggestions are
appreciated very much

Hi Monketrip28,
Sorry for the delay.
"The service show it is working. Also I have found thatEthernet Driver & Base System Driver is not been installed
as well. "
According to your description , I would suggest you to install another virtual NIC for this problematic VM .
If you did not uninstall the ethernet driver , Maybe you can get further assistance from VMware forum :
https://communities.vmware.com/welcome
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to distribute my windows phone 8 app and windows store app without publishing in the store

How to distribute my windows phone 8 app and windows store app without publishing in the store
any business license or enterprise license needed..
I am a windows developer talking behalf of my company i.e wipro
I have a question about the enterprise license and we are building an app for the limited users i.e our company employees and users and we do not want to publish in the store
How to release the app?
what are licenses etc needed?

Hi,
for developers distributing apps without Publishing in the Store, the sideloding Enterprise key license through volume licensing is required.
Starting May 1, 2014, customers who want to enable sideloading will be able to purchase an Enterprise Sideloading key for $100 through the Open License program.
An unlimited number of devices can be enabled for sideloading using this key.
thanks
diramoh

Windows 2008 Licensing - Standard and Enterprise Edt - No of License required

Hello All ,
We have a Windows Environment running on VMware (ESXi5.1), running Windows 2008 Standard and Enterprise platforms . We are working on the no of license that is required for each category . Can you help us in licencing calculation for each environment
.Below is the split
Windows 2008 R2 Standard Edt.
ESX Cluster 1
Total No of ESX Hosts :4
Total No of Windows 2008 R2 Std Edt VMs : 9 // How many license req ? Calculation
Total No of Windows 2008 R2 Ent Edt VMs : 6 // How many license req ? Calculation
ESX Cluster 2
Total no of ESX Hosts : 3
Total No of Windows 2008 R2 Std Edt VMs : 13 // How many license req ? Calculation
Total No of Windows 2008 R2 Ent Edt VMs : 6 // How many license req ? Calculation
Appreciate your support

Hi Sathish,
I would recommend you to contact the Microsoft Volume Licensing Service Center at the following
Microsoft website. They are the experts and can guide you with the proper license requirments.
https://www.microsoft.com/licensing/servicecenter/
Find your local Volume Licensing Service Center support contact information below. Select your country from the drop-down list and the correct Support Center will
be displayed at right.
https://www.microsoft.com/licensing/servicecenter/Help/Contact.aspx
Regards,
Rafic
If you found this post helpful, please give it a "Helpful" vote.
If it answered your question, remember to mark it as an "Answer".
This posting is provided "AS IS" with no warranties and confers no rights! Always test ANY suggestion in a test environment before implementing!

Migration of windows 2008 std 32bit DC to windows 2012 std

i have 32bit DC in my local environment having schema ver 44.. now i hav another server and want to migrate to windows 2012 std edition.. can some one guide me how to achieve this task?

Hi Babarmunir,
In-place upgrades from 32-bit to 64-bit architectures are not supported. All editions of Windows Server 2012 are 64-bit only.
Domain controllers that run 64-bit versions of Windows Server 2008 or Windows Server 2008 R2 can be upgraded to Windows Server 2012. You cannot upgrade domain controllers that run Windows Server 2003 or 32-bit versions of Windows Server 2008. To replace
them, install domain controllers that run a later version of Windows Server in the domain, and then remove the domain controllers that Windows Server 2003.
Hence you need to have a fresh x64 machine which you can join to domain and install ADDS Role then promote as additional domain controller.
Provided the Forest Functional Level is Windows Server 2003 at minimum.
Upgrading previous retail versions of Windows Server to Windows Server 2012:
http://technet.microsoft.com/en-in/library/jj574204.aspx
Upgrade Domain Controllers to Windows Server 2012 R2 and Windows Server 2012
Use the below guide to setup the ADC:
Step-By-Step: Adding a Windows Server 2012 Domain Controller
System requirements for Windows Server 2012 are unchanged from Windows Server 2008 R2. For more information, seeWindows Server 2008 R2 with SP1 System Requirements (http://www.microsoft.com/windowsserver2008/en/us/system-requirements.aspx).
The Schema and Domain preparation: One could run
Adprep prior to ADDS Role installation, Regardless, if Adprep is not detected, it will automatically be completed on your behalf.
Regards,
Satyajit
Please“Vote As Helpful”
if you find my contribution useful or “MarkAs Answer” if it does answer your question. That will encourage me - and others - to take time out to help you.

Epson LX-300, Epson FX-890 printers in Windows Server 2008 x 64 and Windows 7 (x32 and x64)

I have the following problema working with RDP connections to Windows 2008 Server (x64) SP2 and Windows 7 Professional (x32 & x64).
I have setup correctly an Epson LX-300, LX-300+, LX-300+II and FX-890 printers in separate computers in Windows 7 (all working under Windows 7 Professional x64 and x32) and they work correctly.
I need to RDP to a Windows 2008 Server SP 2(x64) and once I log in, the Server Operating System recognizes my printer with no problem at all (Redirected Printer), but when I print, the characters and not understandable, since the printed information is blurry.
When I do excatly the same procedure but with a Client with Windows XP installed the printed information is totally clear, so we can determine at least that the printers are working fine.
I understand this should be a driver issue, but i simply can't make it work correctly.
Can anybody help.

Hi,
Since the printer can print the test page, there is no need to collect the Event log. I notice there is no specify driver for Windows 7 and Windows Server 2008. It seems the default Easy Printer driver doesn’t work properly for these printers.
I suggest you install the Windows Vista driver version on the Server for testing.
LX-300 Impact Printer
LX-300+ Impact Printer
LX-300+ II Impact Printer
If the issue persists, let’s disable Easy Printer for a test.
Computer Configuration\Administrative Templates\Windows Components\Terminal Services\Terminal Server\Printer Redirection ->
Disabled
Also test the following KB.
http://support.microsoft.com/kb/959442/en-us
Niki Han
TechNet Community Support

Scanning from Windows 2008 Scan Manager and an HP 8500 A909A

I am trying to set up a Scan server on Windows 2008 R2 and can not get it to recongnize my HP8500 A909a MFP. I can print to it from the Print Server (via the network), but not scan from it from the Scan Server.

Same problem here. Got it to scan by logging into printer ip.

Printing Issues with HP OfficeJet 100 and Windows 8.1

We use HP OfficeJet 100 mobile printers and have a printing issue.When we print the printer acts as if it is going to print and then prints one blank page.Printer will not print even though it is showing as default printer.Printer will just stop printing in the middle of a document, even in the middle of printing out a page. We are printing via the USB cableWe are using Windows 8.1We are connecting to laptopsWe have been using the HP mobile range of printers since 2004 and have only experienced these issues since we moved the laptops onto Windows 8/8.1 We have:Uninstalled and reinstalled the printer drivers – this fixed this issue for a short while and then it reappeared againCalled HP support and they directed us to the driver support page which had the latest print drivers, uninstalled and reinstalled drivers with them on the phone. This initially fixed the problem and then it returned a few days laterAfter trawling the support forums found directions to change the print processor to “WinPrint” – No effect as the processor was already on this settingDownloaded the HP diagnostic tool – HP Print and Scan Doctor – didn’t fix anything Any further help would be much appreciated.

Hello there Lawrence, Welcome to the Forums! I hope you enjoy your experience
I noticed your post about the troubles you are running into when you attempt to install your OJ 6100 printer on your Windows 8.1 laptop. I read all of your attempts and seen you have tried several methods to try and get the installation to complete successfully.
I would like to make some suggestions that may help. Let me know how it goes!
1. Check that Internet Explorer pop-up blockers are turned off before downloading the installer
Internet Explorer Pop-up Blocker: How do I turn off Pop-up Blocker?
Try to install
2. If you're running McAfee Live Safe or any other firewall, please temporarily disable the "real time scanning".
How to disable realtime scans
Try the install
3. Go to the start screen (you may also press the windows key + R to open the run box) and type %WINDIR% this should show the windows folder.
Click on the folder and scroll until you see files. Look for a filed named "HPWINS*.DAT" (the * is for a number that varies) remove this file and try the installation.
Try the install
Enjoy your Monday!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Windows 2008 64 bits and BO XI 3.1

Bonjour,
Que faut il faire pour installer BO XI sans problème sur un serveur windows 2008 64 bits virtualisé ? paramètres,composants 32 bits à installer ou à paramétrer ??
Merci de votre réponse
Cordialement
F. Bedouin
02.23.21.76.54

Hi Francoise,
You should be aware that SDN forums are English spoken forums.
I don't know BO products and so cannot help you but I suggest that you rewrite your question in English for a better chance to get a useful answer.
Regards,
Olivier

Printer error with HP Laserjet 6L and Windows 7

I have an old but still functional HP Laserjet 6L (from the late 1990s), which is connected to a new computer running Windows 7 via USB. Windows 7 found the necessary drivers, but I am having frequent printer errors come up in the Printer queue, and the machine refuses to print. The problem is 'solved' when I restart my PC, and the document then prints. However this is a pain, and I obviously don't want to have to restart every time I want to print.
I would be very grateful for any advice on this. Thanks.

I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at: http://h30499.www3.hp.com/t5/Printing-and-Digital-Imaging/ct-p/bsc-412
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Windows 2008 64-bit and Microsft ODBC for Oracle problem

Hello,
I am trying to create ODBC connection to Oracle 9i Database on remote server. I am using Windows 2008 64-bit but it is not showing Microsoft ODBC Driver for Oracle. Could any one suggest what to do?\\
Thanks

GQ wrote:
Hello,
I am trying to create ODBC connection to Oracle 9i Database on remote server. I am using Windows 2008 64-bit but it is not showing Microsoft ODBC Driver for Oracle. Could any one suggest what to do?\\
ThanksInstall the Oracle client and use the Oracle driver. You're going to need it whether you use the MS driver or Oracles. ODBC drivers do not work apart from the client of the underlying database product.
When you do the install, you will need to do a custom install and specifically select for the Windows components.

Slow printing on windows 2008 std, R2 and windows 2012

Similar Messages

Maybe you are looking for