Slow Speed after Latency type has been changed

Hi,
the last few days I have noticed that my broadband speed has gone down hill big time.. according to speedtester.bt.com my DSL connection rate is: 20504kbps (down-stream) and my IP Profile is 18090kbps, but my download speed is 2411kbps which is below the acceptable range for my connection.
I logged onto my BTHH3 and found that my latency type has changed from Interleaved to Fast, I have noticed that my CRC & HEC (down) are much higher than before..
Should I leave it for a few days to see improvment or ask the mods to change the latency type back to Interleaved
Thanks in Advance
Andy
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Fast
Noise margin (Down/Up):
3.7 dB / 5.0 dB
Line attenuation (Down/Up):
18.2 dB / 9.4 dB
Output power (Down/Up):
16.4 dBm / 12.7 dBm
FEC Events (Down/Up):
0 / 21224
CRC Events (Down/Up):
102683 / 4252
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
722956 / 10595
Error Seconds (Local/Remote):
2061 / 2095

Results from Speedtester.bt.com
Download speedachieved during the test was - 3887 Kbps
For your connection, the acceptable range of speeds is 4000-21000 Kbps.
Additional Information:
Your DSL Connection Rate :20376 Kbps(DOWN-STREAM), 1176 Kbps(UP-STREAM)
IP Profile for your line is - 17976 Kbps
Upload speed achieved during the test was - 917 Kbps
Additional Information:
Upstream Rate IP profile on your line is - 1176 Kbps
I also re-installed my BT HH2 and that connects using Interleaved as to Fast via BT HH3, while my HH2 is connected I get 15.82mbps via speedtest.net but I keep losing my connection - don't think my HH2 likes 3.7 dB (down) noise margin.. but if I re-connect my HH3 I have a steady connection but 1.6 to 2.2mbps via speedtest.net
I think its time to get a new non-bt router/modem....?

Similar Messages

Is there a way to see what font was used originally, after the type has been converted to outlines?

Hi all, I would really like to know if there is any way to find out what font was used originally in an Illustrator document, after the type has been converted to outlines? The reason for this is I need to update some wording in a couple of old logos I had made and I have NO idea what font I had used...for the life of me I just cannot remember. Because this was so urgent for one of my projects I had to do a search online via "WhatTheFont" to see what font it could be (which I then didn't seem to have in my library!), and repurchase it. I am 99% sure I HAVE the font - or something VERY close - but under a different name.
Normally I keep a much better record of fonts used but there have been times occasionally in the past when I have done something in a hurry and changed the type to outlines without keeping the original, or keeping detailed notes at least. The fact that I did NOT keep notes on a few projects I have done in the past has made me want to kick myself because now I need to revisit one of those again..grrr:)
Can anyone offer any advice? I appreciate your help as always:)
best,
Christine

Christine,
You can also ask in the Typography forum,
http://forums.adobe.com/community/design_development/typography?view=discussions&start=0
The guy running whatfontis is a regular poster there.
And apart from
http://www.whatfontis.com/
there are
http://www.identifont.com/
http://new.myfonts.com/WhatTheFont/
and especially for script,
http://www.bowfinprintworks.com/ScriptIDGuide.html

Router blocks after IP Range has been changed

I am having issues with my A90-9100EM15-10.
I need to change my IP range from 192.168.1.1. to let's say 192.168.22.1 in order to connect to a company network via VPN. I use TheGreenBow IPsec Client for the VPN connection. All connections are wireless.
I changed the IP range on the router, restarted the whole system (including Settop Boxes). All my devices get IP's in the defined range, the Settop Boxes get IP like 192.168.22.100 , ...
Now ever since i did that, my router freezes every day about 2 times. All the lights on the router are green, however i cannot ping the router nor login. There is no recognizable pattern, it doesnt matter if i have all devices on, if i have vpn connection, download or even just have my blackberry online.
I was dealing with verizon customer service, repair, and and and they are not really a help.
The last time i was told that i had to restore the default values as the settop boxes are required to have an ip from 192.168.1.100 ... and up and to wait and see if the problem is resolved. There might be a problem that the boxes do not have ip's like 192.168.1.100, 192.168.1.101, and so forth.
I was supposed to be called back by the tech today, so far no call...
My questions are:
did anyone in here have the same issues
Is it true that i cannot change the IP range without causing problems? I have broadband since over 10 years, and never had an issue like that before.
does anyone know a workaorund?
Any help is greatly appreciated.

Is your WAN port through the COAX or do you have an Ethernet cable from your ONT to your WAN port?
If you have Ethernet to your wan port, you could use a different router not supported by Verizon. If not you would need to have Ethernet run from your ONT to the router location, and then have Verizon turn on Ethernet at the ONT. There are many different ways to configure this while still using the 9100 for the STB connection. But custom configurations will not be supported by Verizon.
Put it back to default and see if you continue to have issues. It may be something that just happened that is unrelated to your IP change. The router may have just started having issues. But if you run something different the default it is hard for them to troubleshoot.
I ran the Actiontec at 192.168.6.x for over a year and no issues. Now I can not say for the Westel 9100. My STBs are issued IPs from my DHCP server that is not a Verizon router and the WAN ports on the Verizon router are not even used. STBs get IPs at 192.168.6.100-106 based on MAC addresses, and works fine for the boxes. My router is a Linux PC box. No NAT table issues here, and yes it logs everything.
Do not expect any remote DVR features to work or any support from Verizon if you are running a custom setup. There are just too many variables for Verizon to support everything people would try and do. But as long as the STBs can hit the internet for guide and updates, all should work fine.

Can you track a form if the file name has been changed after distribution?

I created a form in Adobe Acrobat X Pro -- I then used the distribute feature and sent the form to myself using the internal server. After testing the form, and making sure all was good, I copied the attachment from the email I received when I distributed the form to myself, and sent it to my boss (via outlook). He then changed the file name, and sent the form out to our members. Our members are completing this newly-changed document instead of the original form. They are able to "Submit The Form", and it still looks as though its coming back to me via the dialogue box. However, I have no received any responses in my original document's tracking. When I tried submitting this new form myself to see what happened, I just received an message that says "Your response is being queued for submission", but it never tells you whether the form was actually submitted or not. Is there any way that you can track this form even though the file name has been changed? And if people are submitting their forms to me, where are they going?
Please help!
thanks,
desiree

I understand that you don't want to redo all the linking with the markers. You can try following (make a copy of your project first to be safe) :
- close your project and quit DVDSP
- move your old asset, and replace it with the new one
- reopen your project
A warning message should tell you that this asset has changed, but your marker will remain at old position. If the asset length are not the same, old length information will be used by DVDSP. To correct this, delete the asset from the timeline, and drop it back to the timeline.
Now you just have to move the marker to the right position.

When I leave my iphone in my room and went out. After I came back, I find several apps which was not opened before had been opened. It here are also 8-10 photos of my ceiling being taken, includes video. Also my home page picture has been changed.

When I leave my iphone in my room and went out. After I came back, I find several apps which was not opened before had been opened. It here are also 8-10 photos of my ceiling being taken, includes video. Also my home page picture has been changed.

also my sister said she heard music being played fr my phone suddently. Is my iphone being hacked?

When using tethered capture I often get this notification "The metadata for this photo has been changed by both Lightroom and another application". This slows or stalls the loading of incoming photos. How do I find out which other application is changing

When using tethered capture I often get this notification "The metadata for this photo has been changed by both Lightroom and another application". This slows or stalls the loading of incoming photos. How do I find out which other application is changing the metadata and stop it?

Thanks Sean,
I've had a look at the TC settings dialog and tried to keep it as simple as possible. I also had a copy of LR 4 on the hard drive so have trashed that also incase of any conflicts. LR seems to be running ok now but as said it's an intermittent problem.
I also have a copy of Capture One on the hard drive so am going to uninstall that also in case it is trying to launch.

HT5167 Error after 10.7.4 upgrade..."computer's local hostname ........is already in use on this network. The name has been changed to...... What to do now to get it back to status before 10.7.4 upgrade?

Error after 10.7.4 Lion Upgrade to iMac
Computer's local host name .......is already in use on this network. the name has been changed to........
and it keeps adding up the number each time I wake the iMac.
What to do to get it back before upgrade error?

Ok worth repeating, hope this works. Finally spoke to AppleCare Support and walked me thru following...restart computer holding down "command" and "option" keys at the same time with letters "P" and "R" when computer turns on. This is what he called a PR restart, clears out discrepancies in memory (if that is what the error message actually is). Then went to Systems Preferences/Network/Sharing and deleted the number that kept increasing every time MAC would wake up.
Even tho this was just done, I am hopeful that error pop-up won't happen again. Fingers crossed!

After my computer has been asleep and I touch my trackpad, it wakes enough to show my icon but not enough to acknowledge my keyboard or trackpad so I can type a password. It seems the only way to make it work it to turn it off the back button.

After my computer has been asleep and I touch my trackpad, it wakes enough to show my icon but not enough to acknowledge my keyboard or trackpad so I can type a password. It seems the only way to make it work it to turn it off the back button.

The reason, I included the annotation that I'd upgraded my Itunes, (On my Computer) is B/C in many forums - the very first question, *HELPERS* ask, is. "Do you have the latest version of Itunes downloaded on your computer." I wanted to knock out any obvious replies.
Now- "DO YOU have any idea,"... how your UNHELPFUL remarks, do absolutely nothing but hurt others that might not have the EXPERIENCE you have? How do you expect people to know things without asking questions? Whew! RUDE!!
Message was edited by: Apple I0S Help Team

After installing new operating system software, my user account name has been changed and i don't know the password.

i need help!
I just installed Mac OS Maverick in my laptop, but when i checked the Users&Groups There are only 2 User name 1 is "Apple(admin) and 2 is Guest, my user account name has been changed even the password. how can i retrieve my old user account name and password or how can i changed it?

Here's an updated set of instructions you can try:
Make sure you are signed into iMessage and FaceTime with your current ID. If they are signed into the old ID, go to Settings>Messages>Send & Receive and Settings>FaceTime, tap the ID, sign out, then sign back in with your current ID.
Then temporarily recreate the old ID by going to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. (You should not have to verify the old email account so it doesn’t matter if you no longer have access to it.) Now go to Settings>iCloud, turn off Find My iDevice and enter your current password when prompted (even though it prompts you for the password for your old ID). Then save any photo stream photos that you wish to keep to your camera roll (unless using iCloud Photo Library). When finished go to Settings>iCloud, tap Sign Out (or Delete Account if you are not running iOS 8) and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address back to the way it was. Now you can go to Settings>iCloud and sign back in with your current iCloud ID and password (your data will download back to your device).

Creating a Materialized View Log After the Data has been instered

Hi,
I am trying to create a method of replication from Oracle to MySQL using the Materialized View Log table.
This has been done before and works quite well, the only problem is that I am trying to impliment the log after the table has been created and populated and wish to push all the existing data through the log file...
Does anyone know if it is possible to refresh the Materialized View Log and not a Materialized View.
The way the replication is intended to work is:
Oracle> Data inserted into table
Oracle> writes the vector data to the MVL
Script> Monitors the MVL and can see the changes being made to the Oracle Table
Script> Updates MySQL with the data and removes the rows from the MVL
MySQL is then used with other unix systems
Currently we export the data from the table using Triggers and a cronjob running every x minute to check for changes in the TriggerTables
Many thanks for your time on this, I have been checking for almost a whole working day and not found the answer to this problem.

Thats what I thought, the MVL will only read data that has changed since it was created and wont have the option to load in all the data as though it was made before the table was created.
From what I have read, the MVL is quicker than a Trigger and I have some free code that prooved to work from a MVL using it as a reference to know what records to update. There is not that much to a MVL, a record ID and type of update, New, Update or Delete.
I think what I will have to do is work on a the same principle for the MVL but use a Trigger as this way we can do a full reload if required at any point.
Many thanks for your help.

How to re-trigger BA00 after sales order has been rescheduled

Dear Gurus,
Could you please kindly advise how I could re-trigger BA00 after sales order has been rescheduled?
The scenario is following:
When the sales order was completed, the order confirmation output has been sent to the customer. But later, when the ATP confirmed quantity was changed or order was rescheduled, the committed delivery date has been changed. It caused confusion, because in the order confirmation letter we sent to customer, there is a different date.
I'd like to also trigger BA00 to resend the order confirmation, but I checked the output routine, it only checks if the order is completed or not. Shall I　ask ABAPer to add additional logic in the routine or there is other easier way to re-trigger BA00?
Many thanks in advance!

Have you allowed multiple issue for BA00 output type? In that case, you can manually trigger it from VA02. If you are trying to have it sent automatically, then add the logic into the routine.

RSA1 error Logical system name has been changed for this system

Hello All,
Earlier the RSA1 was activated for client 300 on our crm 5.2. after that we changed the client to 500 using SE16 -> Type table RSADMINA / Check Colum BWMANDT -> 500.
But now when we login to client 500 and execute RSA1 it is showing
Logical system name has been changed for this system"
In scc4 we have not made any changes. Can you tell what should be done ? in the pop up it is showing following steps
Change the name of the logical system (table T000) for client back to SIDCLNT300. This enables you to continue working with the system.
If you really want to change the logical name, than you can, if and when you:
change the system name back to SIDCLNT300,
delete all existing connections between this system and other systems,
delete all transfer structures that still exist, and
do not use ALE or Workflow.
Guys do you know how to fix this ? .
Also do you know Assignment of Source System to Source System ID (table RSSOURSYSTEM) using RSA1 ?
Edited by: Sahad K on Mar 17, 2008 10:55 AM

Hello Hari,
Both the options you said cannot be used
since the logical system SIDCLNT300 is used by client 300 and it cannot be given to client 500. Also there already exist a logical system SIDCLNT500 which is assigned to client 500.
I found out the issue. In the table RSBASIDOC the logical system name that can use rsa1( bw client )is set as SIDCLNT300). Only if we delete that entry and set it to SIDCLNT500 ( 500) we can use it on client 500.
The solution is specified in /message/3284842#3284842 [original link is broken]
Let me try the solution 2 and inform you.
Solution 2:
You cannot delete the source system. Two cases have to be distinguished:
The source system still exists.
Switch to Transaction SM59. Find the destination which has the same name as the logical system of the source system from field SLOGSYS in table RSBASIDOC (see above).
Such a destination does not exist in Transaction SM59. In this case, you have to create the destination to the source system. Name the destination equal the entry in SLOGSYS from above. Then return to the Administrator Workbench and repeat the deletion.
The entry exists but a remote login is not possible. Correct the communication parameters.
Everything works. Change to Transaction SE37, function module RSAR_LOGICAL_SYSTEM_DELETE, Sngl. test. Parameter I_LOGSYS = <log. name of the source system>, I_FORCE_DELETE = 'X'.
The source system no longer exists or was replaced with another source system with the same IP address.
Proceed as described in the first case but make sure, that the field 'Target host' contains a not existing server in the maintenance screen of the destination (Transaction SM59). If necessary, change an existing entry. Later when you delete, the system asks you whether you want to delete, although the source system is not available. Select 'Ignore'.
Incase you have any idea other than this please let me know how to edit the RSBASIDOC table and change the entry to client 500.
Edited by: Sahad K on Mar 18, 2008 5:07 AM

Should I ok "this computer's local hostname Irma-Mac-mini-local" is already in use on this network. The name has been changed to Irma2 Mac-mini 2-local

Should I ok this message-this computer's local hostname Irma's Mac-mini-local is already in use on this network. The name has been changed to Irma's Mac-mini-2local

Don't think this is a conflict with IP Addresses or computer names
= DHCP hangover when computer renews DHCP lease
There is no actual other computer
It just appears that way when reconnects so creates new -2 computer name
What types of names do you use your computers ?
Whether you name them after quantum particles or the romantic poets...
They will each start to be appended with "-2" then "-3" etc if you auto configure network settings from Airport Router DHCP service and you have this Change computer name issue where pop up window states name is already being used on your LAN
As stated previous post you can reset the computer name in SysPrefs / Sharing / Edit button
And restart Router or renew all DHCP leases (if persists in not allowing original name)
Can now press Edit and reset name of choice
But for Fix see link above

You have been signed out from iMessage because your AppleID or password has been changed

I can not connact to iMessage. The following message is displayed after entering Apple ID and Password.
"You have been signed out from iMessage because your Apple ID or Password has been changed."
Apple ID is confirmed.
Date and time and country setting o.k.
Apple ID works to buy things in the apple store.
Imassege works with the ID from my father.
Thank you

Another problem with Firefox is that if I'm typing up a long paragraph in my Yahoo email that takes about 10-15 minutes or more, then when I hit send, I get a Yahoo sign in page. All that typing is gone!! Now I have to type the whole thing over again, if I can remember it. It's pain in the butt!!
I've learned the hard way that any time I use Firefox, I have to copy & paste it to Notepad, sign back in, and paste it in my email, and hit send before it happens again. I don't have this problem w/I.E. The problem I do have w/I.E. is that it takes forever to work. That's why I went to Firefox but now Firefox has problems.

CME: phone number has been changed from 8 digit to 9 digit

Hi Folks,
I have a site who is in Rio, Brazil whos cell phones has been changed from 8 digit to 9 digit. In order for me to comply I need to update the dial peer/plan for CME 8.6 . Anyone who can give advice or instructions is appreciated.
e.g
Example: +551521 9691-XXXX changed to +551521 9 9691-XXXX
Thanks

here you go..
voice class custom-cptone BR-Anatel
dualtone ringback
   cadence 1000 4000 1000 4000
dualtone disconnect
   frequency 425
   cadence 250 250 250 250
voice translation-rule 1
rule 1 /^00[1-9][1-9]$.*$$/ /015\1/
rule 2 /^000[1-9][1-9]$.*$$/ /0015\1/
rule 3 /^090[1-9][1-9]$..........$$/ /9015\1/
voice translation-profile ChangeCSP
translate called 1
license udi pid CISCO2921/K9 sn XXXXXXX
hw-module pvdm 0/0
username admin privilege 15 secret 4 xxx.x.x..x.x.x.xx.x.x
username liderit privilege 15 secret 4 xxx.x.x..x.x.x.xx.x.x
redundancy
controller E1 0/0/0
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-21 type r2-digital r2-compelled ani
cas-custom 0
   country brazil
   metering
   debounce-time 10
   answer-signal group-b 1
   trunk-group Vivo-E1
controller E1 0/0/1
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
translation-rule 1
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address xx.xxx.x.xxx 255.255.xxx.xxx
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 xx.xxx.x.xxx
snmp-server community sparky RO
snmp-server community abc123
snmp-server location Brazil
tacacs-server host xx.xx.x.xxx timeout 5
tacacs-server directed-request
tacacs-server key 7 xxxxxxxx
control-plane
voice-port 0/0/0:0
translation-profile outgoing ChangeCSP
disc_pi_off
cptone BR
timeouts interdigit 5
timeouts call-disconnect 0
bearer-cap Speech
voice-port 0/1/0
trunk-group Vivo-Analog
translation-profile outgoing ChangeCSP
disc_pi_off
cptone BR
timeouts interdigit 5
timeouts call-disconnect 0
connection plar 6500
description ### Vivo +55 11 3078-9782 ###
bearer-cap Speech
voice-port 0/1/1
trunk-group Vivo-Analog
translation-profile outgoing ChangeCSP
disc_pi_off
cptone BR
timeouts interdigit 5
timeouts call-disconnect 0
connection plar 6500
description ### Vivo +55 11 3078-9728 ###
bearer-cap Speech
voice-port 0/1/2
trunk-group Vivo-Analog
translation-profile outgoing ChangeCSP
disc_pi_off
cptone BR
timeouts interdigit 5
timeouts call-disconnect 0
connection plar 6500
description ### Vivo +55 11 3078-9735 ###
bearer-cap Speech
voice-port 0/1/3
disc_pi_off
cptone BR
timeouts interdigit 5
timeouts call-disconnect 0
connection plar 6500
shutdown
description ### Intercom ###
bearer-cap Speech
mgcp profile default
dial-peer voice 1 pots
trunkgroup Vivo-E1
description ### PSTN inbound ###
incoming called-number .T
direct-inward-dial
dial-peer voice 2 pots
trunkgroup Vivo-E1
description ### Local Calls - Fixed ###
destination-pattern 0[2-5].......
dial-peer voice 3 pots
trunkgroup Vivo-E1
description ### Local Calls - Mobile ###
destination-pattern 0[6-8].......
dial-peer voice 4 pots
trunkgroup Vivo-E1
description ### Local Calls - Mobile ###
destination-pattern 09T
forward-digits 9
dial-peer voice 5 pots
trunkgroup Vivo-E1
description ### Long Distance Calls - Fixed ###
destination-pattern 00[1-9][1-9]..[2-6].......
forward-digits 13
dial-peer voice 6 pots
trunkgroup Vivo-E1
description ### Long Distance Calls - Mobile ###
destination-pattern 00[1-9][1-9]..[7-9].......
forward-digits 13
dial-peer voice 7 pots
trunkgroup Vivo-E1
description ### International Calls ###
destination-pattern 000T
prefix 00
dial-peer voice 8 pots
trunkgroup Vivo-E1
description ### Toll Free Calls ###
destination-pattern 00800T
prefix 0800
dial-peer voice 9 pots
trunkgroup Vivo-E1
description ### 0300 Calls ###
destination-pattern 00300T
prefix 0300
dial-peer voice 10 pots
trunkgroup Vivo-E1
description ### 0303 Calls ###
destination-pattern 00303T
prefix 0303
dial-peer voice 11 pots
trunkgroup Vivo-E1
description ### Emergency Calls ###
destination-pattern 019.
forward-digits 3
dial-peer voice 12 pots
trunkgroup Vivo-E1
description ### Service Numbers Calls ###
destination-pattern 01[0-8]T
prefix 1
dial-peer voice 13 pots
trunkgroup Vivo-E1
description ### Local Calls - Collect Calls Fixed ###
destination-pattern 09090[2-5].......
prefix 9090
dial-peer voice 14 pots
trunkgroup Vivo-E1
description ### Local Calls - Collect Calls Mobile ###
destination-pattern 09090[6-8].......
prefix 9090
dial-peer voice 15 pots
trunkgroup Vivo-E1
description ### Local Calls - Collect Calls Mobile ###
destination-pattern 090909T
prefix 90909
dial-peer voice 16 pots
trunkgroup Vivo-E1
description ### Long Distance Calls - Collect Calls ###
destination-pattern 090[1-9][1-9]..[1-9].......
forward-digits 14
dial-peer voice 22 pots
trunkgroup Vivo-Analog
description ### Local Calls - Fixed ###
preference 1
destination-pattern 0[2-5].......
dial-peer voice 23 pots
trunkgroup Vivo-Analog
description ### Local Calls - Mobile ###
preference 1
destination-pattern 0[6-8].......
dial-peer voice 24 pots
trunkgroup Vivo-Analog
description ### Local Calls - Mobile ###
preference 1
destination-pattern 09T
forward-digits 9
dial-peer voice 25 pots
trunkgroup Vivo-Analog
description ### Long Distance Calls - Fixed ###
preference 1
destination-pattern 00[1-9][1-9]..[2-6].......
forward-digits 13
dial-peer voice 26 pots
trunkgroup Vivo-Analog
description ### Long Distance Calls - Mobile ###
preference 1
destination-pattern 00[1-9][1-9]..[7-9].......
forward-digits 13
dial-peer voice 27 pots
trunkgroup Vivo-Analog
description ### International Calls ###
preference 1
destination-pattern 000T
prefix 00
dial-peer voice 28 pots
trunkgroup Vivo-Analog
description ### Toll Free Calls ###
preference 1
destination-pattern 00800T
prefix 0800
dial-peer voice 29 pots
trunkgroup Vivo-Analog
description ### 0300 Calls ###
preference 1
destination-pattern 00300T
prefix 0300
dial-peer voice 30 pots
trunkgroup Vivo-Analog
description ### 0303 Calls ###
preference 1
destination-pattern 00303T
prefix 0303
dial-peer voice 31 pots
trunkgroup Vivo-Analog
description ### Emergency Calls ###
preference 1
destination-pattern 019.
forward-digits 3
dial-peer voice 32 pots
trunkgroup Vivo-Analog
description ### Service Numbers Calls ###
preference 1
destination-pattern 01[0-8]T
prefix 1
dial-peer voice 33 pots
trunkgroup Vivo-Analog
description ### Local Calls - Collect Calls Fixed ###
preference 1
destination-pattern 09090[2-5].......
prefix 9090
dial-peer voice 34 pots
trunkgroup Vivo-Analog
description ### Local Calls - Collect Calls Mobile ###
preference 1
destination-pattern 09090[6-8].......
prefix 9090
dial-peer voice 35 pots
trunkgroup Vivo-Analog
description ### Local Calls - Collect Calls Mobile ###
preference 1
destination-pattern 090909T
prefix 90909
dial-peer voice 36 pots
trunkgroup Vivo-Analog
description ### Long Distance Calls - Collect Calls ###
preference 1
destination-pattern 090[1-9][1-9]..[1-9].......
forward-digits 14
dial-peer voice 99 pots
destination-pattern 9
port 0/1/3
forward-digits all

Slow Speed after Latency type has been changed

Similar Messages

Maybe you are looking for