SM bus driver with yellow mark after Windows XP Pro installation

I have at last got windows xp pro loaded. But in device manager theres a yellow mark on sm bus driver. From searching the forum I seem to have fould out its in the video driver pack from ATI. But when the driver is loaded it messes windows up so it will not boot.
Can anyone help?
Paul

Hi
I read you other threads and it seems you have a Satellite Pro A60 notebook.
What can I say you have installed the OS manually and in my opinion a simply driver is missing
Did you try to install the infrared driver from the Toshiba European driver page?
Possibly this is a key
Anyway, before you start the OS manual installation you should read the Installation Instructions. There you will find whole drivers which must be installed and the right installation order.
Please check this document and follow the guide lines

Similar Messages

Not solved with Blinking Folder with Question Mark after Erasing Hard Drive

Before asking, I found someone had asked exact the same question, but that was actually an unsolved thread.
Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
Level 1(0 points)sdc3gJul 5, 2013 6:24 PM Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
Re: Blinking Folder with Question Mark after Erasing Hard Drive to try to restore to Factory Settings
in response to Niel
Thanks for the reply, held command+R again and it is trying to pick up WiFi, but it's not picking up my network and won't accept the password even when I try to put it in manually. Any thoughts on that?
Me too had tried the command+R and failed to manually connect to my network. Can anyone help?

Well, it was solved. I shifted to other place and tried other WIFis. One of the WiFi had the 2002f problem and another was fine, so the reinstall worked smoothly eventually.
On the apple support page it says that Supported network configurations and protocols includs both WPA/WPA2, not matter what they are, but it might not be true.

A USB thumb drive with data created in Windows is not showing up on my desktop. Do I need a different driver or something?

A USB thumb drive with data created in Windows is not showing up on my desktop. Do I need a different driver or something?

OK in order to read those files you will need MS Office for Mac or install MS Windows on your Mac. You can get MS Office for Mac from anyone that sells Apple products. I would suggest the Apple Store, Best Buy, Amazon etc...For help getting the data from the memory stick I'd recommend visiting your local Apple Store or AASP and they can help you move it. It should be as simple as plugging the USB drive into your USB port and then open a Finder Window where you will see the drive on the left pane. If you don't know what Finder is or how to open a new Finder window you need the sites I've noted below!!!
Because you are new to OS X I would strongly recommend you bookmark and frequently visit the following web sites:
Switch 101
Mac 101
Find Out How Video tutorials

I am working on a MacBook Pro (13-inch, Mid 2009) with boot camp running Windows 7 pro 64-bit. Windows crashes quite often now-a-days and I need to get this fixed. I heard that updating boot camp can help. Currently I am running Version 3.0.4 (322).

I need to know which update(s) I can apply to help stabalize the system.

Typing the body of the thread message in the title, huh? -)
I am working on a MacBook Pro (13-inch, Mid 2009) with boot camp running Windows 7 pro 64-bit. Windows crashes quite often now-a-days and I need to get this fixed. I heard that updating boot camp can help. Currently I am running Version 3.0.4 (322).
Only Apple could hamstring and tie Mac OS to Windows. There isn't any other than whether you can download the drivers into Windows (you can) but Apple puts a block on the installer setup even if your mac does not support it.
Windows 7 needs at least Boot Camp 3.1 and 3.3 is what you should already have. And you are not getting security updates if you don't have at least 10.6.8 as was pointed out. --- you arent using Software Update as you should. And you should backup and clone Mac (and Windows) as well.
You need Mountain Lion to use Boot Camp 5.x which supports Windows 7 & 8 and 64-bit.
I would upgrade to Lion if you can realizing that Rosetta and PowerPC are no longer supported though.
Mac 101: Using Windows on your Mac via Boot Camp
https://support.apple.com/kb/HT1461
http://www.apple.com/support/bootcamp/
Helpful Apple Support Resources (Forum Overview)
Boot Camp Support
Boot Camp Manuals
Boot Camp 5.0 Drivers
http://support.apple.com/kb/DL1638
Frequently asked question
http://support.apple.com/kb/HT4818
http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.7.pdf
http://manuals.info.apple.com/en/Boot_Camp_Install-Setup_10.6.pdf
http://manuals.info.apple.com/en/Boot_Camp_Install-Setup_10.6.pdfcreate a Windows support software (drivers) CD or USB storage media
http://support.apple.com/kb/HT4407
The Boot Camp Assistant can burn Boot Camp software (drivers) to a DVD or copy it to a USB storage device, such as a flash drive or hard drive. These are the only media you can use to install Boot Camp software.
https://support.apple.com/kb/HT4569
http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.8.pdf
Instructions for all features and settings.
Boot Camp 4.0 FAQ Get answers to commonly asked Boot Camp questions.
Windows 7 FAQ Answers to commonly asked Windows 7 questions.
http://www.apple.com/support/bootcamp/
Is there a download of the Boot Camp 5 Support Software if I'm not using OS X Mountain Lion v10.8.3?
Yes, you can download the Boot Camp 5 Support Software here.
http://support.apple.com/kb/DL1638
How do I use the Boot Camp 5 Support Software I downloaded from the web page?
The download file is a .zip file. Double click it to uncompress it.
Double-click the Boot Camp disk image.
Copy the Boot Camp and "$WinPEDriver$" folders to the root level of a USB flash drive or hard drive that is formatted with the FAT file system (see question below for steps on how to format).
Install Windows, leaving the flash or hard drive attached to the USB port of your Mac.
Installation of the drivers can take a few minutes. Don't interrupt the installation process. A completion dialog box will appear when everything is installed. Click Finish when the dialog appears.
When your system restarts your Windows 8 installation is done.
Note: If the flash drive or hard drive was not attached when you installed Windows and was inserted after restarting into Windows 8, double-click the Boot Camp folder, then locate and double click the "setup.exe" file to start the installation of the Boot Camp 5 Support Software.
How do I format USB media to the FAT file system?
Use Disk Utility to format a disk to use with a Windows computer. Here's how:
Important: Formatting a disk erases all the files on it. Copy any files you want to save to another disk before formatting the disk.
Open Disk Utility.
Select the disk you want to format for use with Windows computers.
Click Erase, and choose one of the following from the Format pop-up menu:
If the size of the disk is 32 GB or less, choose MS-DOS (FAT).
If the size of the disk is over 32 GB, choose ExFAT.
Type a name for the disk. The maximum length is 11 characters.
Click the Erase button and then click Erase again.
Which versions of Windows are supported with Boot Camp 5?
64-bit versions of Windows 8 and Windows 7 are supported using the Boot Camp 5 Support Software. If you need to use a 32-bit version, you need to use Boot Camp 4 Support Software, and you must use Windows 7. 32-bit versions of Windows 8 are not supported via Boot Camp. For a complete list of Windows OS support, click here.

Initial issues with PS CS4 Extended Windows XP Pro.

Initial issues with PS CS4 Extended Windows XP Pro.
CS3 worked just fine but had many issues with Bridge CS3. So frustrating that the $$ to upgrade to CS4 seem worth it. Mostly works OK with the following exceptions:
1. Sometimes the file menu selections are non-selectable grey including fundamental functions like Open and Exit not even clicking on the x will allow PS to close! I found a workaround, I can select a tool that is not currently selected (like the crop or brush) and now the menu items appear.
2. The Arrange Documents drop down menu is blank except for the lower text portion. All icons are missing. Roll over text popup shows what is supposed to be on the menu but no icons.
3. I have setup Bridge CS4 to auto start at logon. Works OK but sometimes for whatever reason stays busy after I close. Task Manager shows Bridge using up to 25% of CPU time and the program is not even open!
5. I purchased a couple Canon EOS 50Ds as backup cameras for our business. Worked last week with CS3 and Bridge with Raw 4.6 upgrade. Does not work with RAW 5.0 in CS4bummer!

I had the same problem with blank/missing "Arrange Documents" icons. And I use NIK and OnOne plugins (CS4 & Vista). These plugins are all supposed to be compatible with CS4 and I use them ALOT - so I refused to remove them. Today I also started having a problem with an error re: needing to install a printer before I could select print functions.
I found the answer to both problems!! While researching the error message I found information from Adobe support stating that you should:
1. Quit Photoshop
2. Vista: Rename the Users\[username]\AppData\Roaming\Adobe\Adobe Photoshop CS4\Adobe Photoshop CS4 Settings\Adobe Photoshop CS4 Prefs.psp file to Adobe Photoshop CS4 Prefs.old
Windows XP path: Documents and Settings/[username]/Application Data/Adobe/Adobe Photoshop CS4/Adobe Photoshop CS4 Settings/Adobe Photoshop CS4 Prefs.psp
3. Start Photoshop - it will create a new preferences file.
My print error message is gone AND I have Arrange Documents icons!!!

Folder with question mark after unpartitioning hard drive

I am running Snow Leopard on my Mac Book Pro.I unpartitioned my hard drive with Boot Camp. Now when I start up I get a folder with a question mark (not a flashing question mark) and then the apple logo. I repaired the disk permissions but there is no change. I don't know what to do now. I really do not want to reformat the hard drive if I don't really have to. What do I do now?

Have you tired holding down the Alt/Option-key at startup to get the Boot Selection Screen ?
If you can boot into your OSX go to System Preferences -> Startup Volume and reset your OSX to be the default.
Stefan

Boot Camp: Early 2011 MacBook Pro boots to black screen with blinking cursor after windows 7 installation.

I bought and downloaded the windows 7 ultimate edition 64 bit iso, then proceeded to perform a correct burn to a DVD one at the slowest speed and one at the fastest. all went well. so I open Boot Camp assistant and follow the instructions to the letter, downloaded the driver support to the flash drive. partitioned my drive with more than enough room 150 gb. its starts its install. I get through everything seamlessly where I put in my info all with the exception of my activation code. yet it still continues to finalize the install and does another restart. boots back up to either A. black screen saying press any key to boot to my install disk. B. if I take it out just a white curser. also I read it may be because I had the flash drive in while I was trying to boot so I removed it as well, same result. any input would be much appreciated.

Boot Camp- Windows installation boots to black screen with blinking cursor.

I have a seagate external hard drive with files copied from windows pc. If I will download NTFS driver from seagate to my mac, could I install it safely without harming my files in the external hard drive? I am afraid I may erase all files in there.

I have a seagate external hard drive with files transferred from my windows pc. If I will download NTFS Driver from seagate to my mac, could I install it safely without harming my files? I am afraid.. I might erase all my important files during the installation..

Thanks a lot! I have already downloaded Paragon Driver and it works well with seagate external hard drive. I am copying as of now my important files from my mac to it. However, I have only the trial version which will expire in 10 days. I don't have credit card to buy for it.

My MacBook pro stop working and it shows folder with question mark after this update, it's not my fault, Apple should solve the problem with out ask me to make payment

After updating my MacBook pro it shows only a folder with question mark on it
It is not my fault, Apple updates problem
They should solve it fir me without make any payment
Thanks

Try starting your computer holding down the option key as soon as you hear the startup sound, and continue holding it. Hopefully, you will see the icon for your startup disk come up on your screen within a minute. Click on that icon and press return. If your machine starts up normally from there, go to System Preferences > Startup Disk and reselect your startup volume

Flashing Folder with Question Mark after Trackpad 1.0 Update

My machine won't boot after installing this update. I get the flashing folder with question mark and can't even boot from the Install DVD either... I just get a frozen spinney wheel at the Apple Logo screen. I've tried resetting the PRAM and everything else that a Googling of the problem suggests. This update bricked my Macbook!!!!
Anybody else having this problem? Anybody have any suggestions or am I stuck with going to see a "genius"?

I've not seen any other posts about it causing problems, worked fine here. You've tried resetting the PRAM the only other thing you could try is:
Boot holding down Apple/S and don't let go until you see scrolling text.
When that stops and you see a root#: prompt enter
fsck -fy
Let it run through all the checks and repairs.
If it fails first time, at any time, or finds and fixes a fault - run the command again and keep doing so (some fixes can take several passes) until it says "Appears to be OK" then enter
reboot

No headphone sound after Windows 7 clean installation

Hello.
I recently performed a clean installation of Windows 7 Home Premium. Before that on preinstalled Windows the problem described below did not show up, sound worked just great.
Now I don't have sound when inserting my headphones in jack (built-in speakers work fine however). Windows reports that sound works, no problems found, but I hear nothing. On the same computer I have also Linux installed and the same headphones work well there in the same jack.
When I put my headphones in, Realtek Manager makes notification that the device is plugged in.
My model is Qosmio X775-3DV78. What I have tried so far:
1) Reinstalling, updating, removing, trying different versions of Realtek HD Audio driver.
2) Changing every possible setting in Realtek HD Audio Manager.
3) Trying different headphones - same result: nothing.
4) Changing settings in Playback Devices.
Since it worked before reinstalling Windows and since it works on Linux on the same computer, there is definitely something wrong with my drivers. Could you please provide information as to what drivers exactly I should have installed to make sound work correctly? Maybe some motherboard driver is missing (though I installed everything important I could find on Toshiba site).
Attached are some important screenshots. Please note that there are 2 unknown devices in my Device Manager and also USB Controller driver has problems, though I do not think it has any connection with the problem.
* On both Playback Devices forms Disabled Devices and Disconnected Devices are shown.
Thanks!
UPDATE: One of "Unknown devices" proved to be Toshiba HDD Shock Sensor driver and another one is ACPI\TOS6205.
Attachments:
ToshibaSupport1.png ‏172 KB
ToshibaSupport2.png ‏44 KB
ToshibaSupport3.png ‏21 KB

I have just done the same upgrade to Windows7 and I have no sound from the headphone jack. Also when I plug into it, I don't get the old Realtek Audio evaluation screen for audio setup.
However I do not use headphones, as I have been using a RCA jack to plug from the headphones output jack to
a portilble shortwave radio that I have utilized the 6 inch woofer for the past three years since buying the laptop new, for better output and base sound from the radio speaker while simultaneously running the stereo built-in speakers on the laptop.
Can someone tell me that I should just update the laptop audio card by re-installing the original Realtek Audio Driver? Is that easily accessible here in the official Toshiba site? Also if possible, please inform me of other driver updates that would most likely need re-installation processes after this Windows 7 update.
Thank you for any info,
Mark Seibold, Portland Oregon *If poossible please reply to my direct email >
[email protected]

X40 BSOD after Windows XP Pro SP3 Update

Any suggestions to recover from this error
inconsistency detected in the pci bus driver's internal structure
stop: 0x000000a1, (0xdead0010, 086fde030, 0x00000000, 0x00000000)
I have spoken to MS and they say it is a driver issue and I have to work w/ Lenovo to resolve
I'm going to try to boot to WinPE and run some of the Lenovo updates to see if this resolves it...
Any help would be appreciated...
Jen

Error code 0x80190194 is the most common error that occurs on windows OS. If the self update virtual directory has been lost or is missing from the default web site then this windows error are displayed.
You solve this update error from the following given steps:
1) Turn-off the any antivirus software program, because if you are update your windows then running program may create problem with us.
2) Remove all recently addition of any software or hardware, because it may create conflict with older program.
3) Restore system, some time it may solve this type of error.
I hope above these steps help you to fix windows update error 0x80190194 on your system. For more information you also visit : http://www.fixwindowsupdateerror0x80190194.com/

Can't play Song After Windows(Boot Camp) installation

Hi
Itune stoped playing many mp3 song .
I installed windows with boot camp and played some songs in windows media player ,
right after I finshed the installation , I tried to play some songs in Itunes, but Itunes won't even recognize them ,
He just skip them , he also removed the artwork icon form them.
those several songs can play with quicklook with no problem .
thanks
Gideon

I have no idea why it didn't work last night but I tried your method again and it worked great! Thank you, saved me the time of going to the apple store

After Windows 10 Pro N succesfull update all Network Adapters not working and not showing up

Hi all, After succesfully installing the new Windows 10 Pro N onto my Windows 8.1 Pro N operating system and restarting the system, I realized that all drivers are migrated succesfully, withouht any incompatibility issue, but none of the network adapters were working, so no WiFi, no LAN connection was ready to be used, checking the list of available network adapters showed an empty list. I am using a ThinkPad T520 laptop. I have tried to update all drivers from a USB, had several restarts, but no result. Any ideas I could use to get Windows 10 up-n-running with network connections? Thank you in advance, Regards, Gyula

Hello and welcome,
Do you have VPN software on your laptop? https://support.microsoft.com/en-us/kb/3084164
Z.

Problems with Fireworks CS3 in Windows 7 Pro 64 bit

I have recently upgraded to Windows 7 Pro from Windows XP Pro. My Fireworks CS3 is having a problem. I cannot select items in the left side menu bar if I minimize or move the Fireworks CS3 window. If I have just opened the window it works, but minimize the window or move it and the toolbar stops working.
This problem is not unique to my machine. 2 other people are having the exact same problem. Here is the link to the Windows 7 forum:
http://www.sevenforums.com/software/26957-adobe-fireworks-cs3-issue.html
We sure could use some help. This is one of my bread and butter programs.

I'm happy to hear you have other work-around alternatives!
Businesses with mission-critical software usually are very careful to research that their software will run on any proposed new system or that alternative software is available. This is the main reason that Microsoft had to continue supporting XP longer than they intended. Too much business-critical software ran on XP but did not run under Vista and would take some time before it would be upgraded to do so...if at all.
If you have "bread and butter" apps, then it was your responsibility to make sure that you could run them once you upgraded. Adobe's software worked more or less as advertised for the operating systems that were available at the time the versions were released. That's reasonable. Expecting indefinite support into the future is not.
Fireworks isn't a $2000 product. Adobe continues product development, yes. They've moved on to CS4 and its patches. You can upgrade to FW CS4 for about $150. The system requirements for FW CS4 do not include Windows 7; note that Fireworks is only certified for 32-bit operating systems:
http://store.adobe.com/store/en_us/popup/software/fireworks4/systemreqs.html
However, there's a statement about CS4 applications (in general) working with Windows 7:
http://www.adobe.com/products/fireworks/faq/?anonymous_element_1=4
And you'd want to get the recent updater:
http://www.adobe.com/support/fireworks/downloads_updaters.html
speedtigger wrote:
... It is probably not a huge problem to fix for an Adobe engineer.
If the feature worked under Vista but does not work under Windows 7, then that means that the problem probably lies somewhere in how the program communicates with the OS. The problem is not isolated to the tens - possibly hundreds - of thousands of lines of Fireworks code, but in how that code interacts with the Windows 7 APIs. To solve this problem is not the work of "an Adobe engineer." It's the work of a project team. It's the work of a project team which would have to be pulled off development of Fireworks CS5 for a few months to resurrect the old CS3 code, get familiar with it, and try to track down and solve the problem, then package up, test, and release a patch . By pulling resources off CS5 development, CS5 would be delayed or quality inversely impacted. Since CS3 is not a current product for sale, I can't see Adobe making this investment. There's no return on it, where there would be a return on getting a quality FW CS5 out the door on time.

SM bus driver with yellow mark after Windows XP Pro installation

Similar Messages

Maybe you are looking for