Small scale network

Probably not the best place for this post, but probably where I'll find the best people to answer my question.
The problem... I wish to set up a very small network to use a printer and external drive with a wireless MacBook. without spending too much money.
The MacBook (obviously) roams the house on a wireless connection. The DLink router sits handily in the cupboard under the stairs. I would like to place my printer and external drive under the stairs with the router and for them to be wirelessly accessable from the MacBook.
The solution that comes to mind is to buy a Mac Mini for under the stairs and connect everything through this. But that seems a terrible waste of a Mini (and more inportantly Money!)
Any better ideas of how to acieve this would be very much appreciated.
With thanks,
David.

I did not able to understand why you want to give ip to two NICs from different subnets.
There is NO any requirement, like that. If you have your own requirement can you explain me that?
Ashman

Similar Messages

  • How to setup a small office network

    Hello,
    I am looking to setup a small office network comprising 6 G4 macs (existing computers) that have been upgraded to the newest OS version. What is the best way to go about networking these computers together in terms of being able to share files, internet connection, access to peripherals and also implementing a firewall.
    Any suggestions or help would be greatly appreciated.
    Thank you

    1, Get a cable internet ISP account; depending on your service you should be able to secure a 5Mbps down and 2Mbps up on the cable e.g. Cox or Comcast.
    2. Get a good router. The mass market Linksys and Netgear routers aren't very good in terms of reliability. I use a ZyXEL P-330W router is the best I've ever seen. Its reliable and very efficient in terms of throughout. The Apple Airport Extreme is good.
    3. Set up the router to support UPnP. This way all computers will be able to share iChatAV video conferencing. If you enabled "port forwarding" only one Mac would be able to use iChatAV video conferencing.
    4. Set up your router for DHCP to dynamically issue Internet address to all your computers.
    5. Setup the wireless router for encryption such as WPA. This will encrypt wireless communication.
    6. Setup the wireless router for only your computers. You'll have to get the MAC/AirPort ID network addresses as expressed in terms of an xx:xx:xx:xx address. You can get this thru your Systems Preferences -> Network window -> AirPort (in the sidebar) -> Advanced button.
    7. If you have Ethernet in your office then skip steps 5 and 6 above.
    8. On each computer open up the System Preferences -> Sharing and check-off the File Sharing. Set your user access preferences appropriately.
    9. Get a Network enabled All-in-one printer and setup Printer Sharing options. Hook-it up to your network and add your printer by clicking on the "+" sign in your "Print and Fax" Preferences.
    10. Don't enable Apple Firewall on each Mac. The router will be the Firewall.
    Ok. That's the short-hand.. plug it all in and go!

  • Randomly monitor small office network

    Looking for a user-friendly, dummy-proof article on creating a small office network from a total of four Mac's (3 iMacs, one Air), allowing the administrator to randomly monitor without detection the real-time activities taking place on the other two machines. Triple points for iOS monitoring capabilities, as well

    Hello, rjbm_exact. 
    You definitely need a managed switch and a Cisco Small Business (200 or 300 series) can meet your requirements. You can setup separate VLAN to segregate user access level. Are you also looking at expanding your wireless (guest access)?
    Let me know if you need more assistance or e-mail ([email protected]) me directly. Kind regards. 

  • Computers on small office network - names getting confused on iChat

    We are using bonjour and iChat on the computers on a small airport network in our office as an instant messaging solution in our office - however, 2 of the computers (which are named differently) keep getting confused and both being called the same name.
    I have done the fix where you go to System Prefs, Users & Groups and then set the address book card to that particular computer owner, restart the computer and then open iChat (using bonjour) - it saves the name but then my colleague becomes the same name as me on iChat - so we do the same thing to her computer (set address book card etc) and it changes her iChat name, but then also seems to override what I had set for mine previously.
    Help!! What can I do to stop these 2 computers seemingly overriding each other? It doesn't happen with the other 4 computers sharing our network...

    Hi,
    In System Preferences > Sharing is the Name the Computer has.
    This does play a part in any Bonjour Connection.
    It is this name that appears in Shares in the Finders's Side bar.
    Separate for that iChat and Messages that have the Bonjour Account Enabled broadcast the details from the My Card in the Address Book.
    Issues can arise with some Server based Logins that create a Global Address book that changes the My Card.
    You get similar difficulties on some DiskImage roll outs of updates and the like if the details of the Address Book are copied as well.
    I am not sure what you mean by the "fix" in System Preferences > Users and Groups to change the My Card or the Computer's Name.
    Yes you can click the Contact Card for that account and it will show you it in the Address Book and it should be th My Card.
    Changing the My Card then does not alter which Card is associated with the Mac User Account.
    There is no access to the Computer's Name
    7:53 PM      Wednesday; August 1, 2012
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
      iMac 2.5Ghz 5i 2011 (Lion 10.7.2)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • Small business network issues!!!

    I am at my wits end with this problem:  We have a small business network consisting of 6 Mac Pro computers and 2 Windows PCs.  Everything was working fine until we needed to replace one of the WinXP machines with a Windows 7 machine.  None of the Macs can see the PCs unless they physically type in the IP address (they used to show up in the finder as the computer name).  None of the PCs can access the Macs at all and now shares on one of the Macs are no longer visible by the rest of the network.  Any help would be appreciated.
    Computers:
    Mac Pro 10.7.5
    Mac Pro 10.6.8 (x4)
    Mac Pro 10.5
    Windows 7 64-bit Professional
    Windows XP Professional
    I have made sure that every computer uses the correct workgroup name and that all file sharing is enabled. 

    I've seen it take 45 minuyes for a PC to announce it's name on the network, just sayin'.
    Anyway, does the PCs IPs ever change?

  • Small home network using a mini

    Hello i'd like to set up a small home network. The component i have are:
    A broadband connection via a cable modem
    A mac mini which can act as a server (i'd like to provide access to shared photos and music, and connect an external HD for backup and storage)
    2 airport wireless routers
    2 macbook pro laptops and 1 mini all with wireless
    Any suggestions as to the most effective way to link this all together?
    Thanks
    Tim

    Hi Tim,
    You've accidentally posted this on the iPod Mini forum, not the Mac Mini!
    Mark

  • Setting up a small business network using mac and windows pcs

    Setting up a small business network using mac and windows??

    Ok that sounds great. What is your actual question as it relates to AirPort networking? Is it: Can I set up a wired/wireless network with an AirPort base station that support multiple Mac & PC clients? If so the answer is yes.
    If, instead, it is how to I configure an AirPort network to support a small business you will have to provide more details on both your networking & computing equipment in order for any of us to help you.

  • Practical requirment of hardware and software to run small scale industry

    Suppose any small scale industry or any chemical plant want to use SAP then what is the requirment of hardware and how much he/she needs to pay to purchase SAP software.
    Assume that 5 to 10 workers are working in the industry on Rs.1000 to Rs.3000 as salary and his net profit is approximatly Rs.40000 per month.
    waiting for reply.

    It's depends on, such as, what country are you talking about?
    You can find the documentation about the hardware requirements in the link below
    https://websmp210.sap-ag.de/~form/sapnet?_SHORTKEY=01100035870000680297&_SCENARIO=01100035870000000183&_ADDINC=011000358700002837782005E&
    or you can looking for "B1 2005 A SP01 Sizing Guide" in SAP B1 portal.
    Regards,

  • Small Scale Labview Contract in Montreal

    Hello, we are looking for a freelance LV programmer to setup a small scale custom data acquisition in our Montreal office.
    This project can be done daytime, evenings or weekends. It should be quite simple for someone with LV experience.
    The applicants must have a minimum of intermediate knowledge of LV and must be located near Montreal.
    If you are interested please send your information to [email protected]
    Regards
    Graziano

    I will be contacting you.
    RayR

  • ACS issues in large scale network with Prime Infra and WAAS express

    Hi,
    I wonder if there is a common practice or a recommended way for deploying large scale network where there are Prime Infrastructure (PI) and WAAS Central manager keep logging into routers (scale of 1000 or more) to collect statistics. The way PI and WAAS CM collect stats from the routers (besides using SNMP) is that they log in (authenticate) themselves with there usernames and password and issue multiple show and config commands on the routers. Imagin this routine happens every 5 - 10 minutes with all 1000+ routers at the same time and the impact to the ACS server in terms of authentication requests and AAA logs. Appreciate if somebody could recommend a solution where these elements can work together in a large scale network.
    Thanks,
    Tos

    The AEBS is connected to the TC via an ethernet run from the basement to the main floor... its not connected wirelessly.
    The "extend" feature is intended for wireless, not wired connections. Since you have the base stations connected by Ethernet, the downstream router just need to be reconfigured as a bridge. The bridged router would then perform as a combination Wireless Access Point and Ethernet switch. Neither base station should be configured for "extending."
    Basically, you will want both to be configured for a "roaming" network.
    o Setup the base station connected to the Internet to "Share a public IP address."
    Internet > Internet Connection > Connection Sharing: Share a public IP address
    o Setup the remaining base station(s), as a bridge.
    Internet > Internet Connection > Connection Sharing: Off (Bridge Mode)
    For each base station in the roaming network:
    o Connect to the same subnet of the Ethernet network
    o Provide a unique Base Station Name
    o The Network Name should be identical
    o If using security, use the same encryption type (WEP, WPA, etc.) and password.
    o Make sure that the channel is set at least three channels apart from the next base station.
    while the TC is running at 2.4ghz since my MBP is connected at speeds around 240 to the AEBS at the same time that my ipod is connected to the TC at speeds of only 54 max.
    The iPod is a 802.11b/g wireless device. It cannot connect at greater than the maximum bandwidth for that mode ... which is 54 Mbps, regardless of the bandwidth available.

  • Cisco small bsuiness Network issues

    I have small business network with following equipment
    Comcast Providers Internet Router
    SA520W Security Appliance
    SG300-20-20Port Small Business Switch
    From Comcast Router Internetworks fine
    after connect SA520W Router I am unable to resolve the host name very quickly its too taking long to resolve  host name to IP address while resolving  dns is getting failed . I thought  there might some issues with Comcast , Comcast tested and no issues their router set to bridge mode .
    After that I come to conclusion that SA520w has some firmware issue  , I updated the new version of firmware for sa520w
    After that connected switch sg300 series after connecting the switch I have similar issue again
    Do I need updated the firmware for the switch as well ,can some one provide firmware Link
    Or any thoughts on present issue
    Thanks
    R

    Hello,
    Im sorry you are having issues with the devices. I really have no idea what could be the problem. Maybe you can try using the DNS servers from google, 8.8.8.8, 4.2.2.1, 4.2.2.2?
    Also, here is a link to the firmware upgrade for the SG300-20. 
    https://software.cisco.com/download/release.html?mdfid=283019616&flowid=18904&softwareid=282463181&release=1.4.0.88&relind=AVAILABLE&rellifecycle=&reltype=latest
    When upgrading the firmware, please keep in mind you should step up the upgrade and please don't go straight to the last one as you may break the device.
    Starting on firmware 1.3.5.8 you will also need to upgrade the boot code when upgrading the firmware.
    Here is a document that explains the process.
    http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=08ef98be59904ccc9c4d69a657f5550f_Firmware_Upgrade_via_TFTP_on_200_Series_Switches.xml&pid=2&respid=0&snid=4&dispid=0&cpage=search
    Please let us know if you have any more questions

  • Best practices for setting up users on a small office network?

    Hello,
    I am setting up a small office and am wondering what the best practices/steps are to setup/manage the admin, user logins and sharing privileges for the below setup:
    Users: 5 users on new iMacs (x3) and upgraded G4s (x2)
    Video Editing Suite: Want to connect a new iMac and a Mac Pro, on an open login (multiple users)
    All machines are to be able to connect to the network, peripherals and external hard drive. Also, I would like to setup drop boxes as well to easily share files between the computers (I was thinking of using the external harddrive for this).
    Thank you,

    Hi,
    Thanks for your posting.
    When you install AD DS in the hub or staging site, disconnect the installed domain controller, and then ship the computer to the remote site, you are disconnecting a viable domain controller from the replication topology.
    For more and detail information, please refer to:
    Best Practices for Adding Domain Controllers in Remote Sites
    http://technet.microsoft.com/en-us/library/cc794962(v=ws.10).aspx
    Regards.
    Vivian Wang

  • Using Time Capsule to backup a small office network

    Hi all,
    I am hoping somebody may be able to tell me if this is a good plan or not. I have been really struggling to find a good network backup solution. I've been trying to make a Lacie Ethernet Disc Mini work but have finally given up on that one.
    I am trying to find a simple solution to backup a network of 5 macs. 1 is currently plugged straight into my router, another router port extends to switch in another building which has 4 further macs along with other network devices connected. Crucially, there is no wireless access from this building to the router.
    Would all macs backup to the Time Capsule, including those that are wired via the switch? If so, at what speed? I have heard suggestions that it can be a very slow process?
    I'm not worried about any kind of streaming - purely a good backup device.
    All advice very gratefully received,
    Regards
    Richard

    Hi Richard,
    I have a small business and chose to use Time Capsule as a backup for my company's network. We have 12 workstations and use all Macs, some wireless and some not. I'm an experienced Mac sys admin and have setup many networks, including designing and installing the network we currently have, which is driven by a Leopard Server.
    Based on a year of experience working with Apple's newest airport extreme and capsule products, I would not use them in business and am moving towards a wireless network hd using Carbon Copy Cloner as my software. This is due in part to numerous calls to Apple for support on these items, having to reset them dozens of times, and being told by Apple support that using these products for business is not recommended.
    Carbon Copy Cloner is a great tool for a backup, especially for workstations, as you can create partitions for each computer on your HD and CCC will create *bootable* backups of your HD - a great lifesaver if a computer fails and you don't have time to reinstall everything.
    I will be putting the capsule and extreme devices on Craigslist for sale and hope to recoup enough to get the wireless network drive, which my research shows is the best way to get network backup solutions for small business.
    I hope this helps.

  • Problem using File sharing  in a small office network

    I have a problem using File sharing on an Imac and Macbook Pro.
    My office has a small network running Windows Small office file server 2003. I have one Windows 2000 PC connected to it and 3 Macs, an 2.4 gHz Intel iMac running Leopard 10.5.6 , a MBP running the same and a Mac Mini running 10.5.
    From the Finder Shared window of the Mac Mini, I can see all the computers on the network. It also used to be the case for the iMac, but the MBP could never see the Windows PC’s, not the server or the Win2000. This wasn’t a big problem as I was communicating between the Macs and using the shared printer on the iMac.
    On Monday Jan 19 the iMac was suddenly unavailable to the other 2 Macs. It was working normally on the Friday. The iMac can access the Mac Mini and copy files to it. The Mac Mini can see the iMac but cannot access it. Even trying to connect as, ends in a failed connection. I have tried rebooting, turning File sharing off and then on again to no avail.
    The iMac now also cannot see the Windows PC’s which it previously could.
    To get files from the MBP for printing, I now copy it to the Mac Mini and acces the folder from the iMac, a very tedious procedure. I don’t know why this happened and am scared that the Mac Mini is going to do the same thing.
    All three computers are also running VMware 2.0 with Windows XP pro, and from VMware the server is visible on all the computers.
    Any help will be much appreciated, I live in a small town in South Africa and the local computer suppliers have no knowledge of the Macs.
    I think that the problem with the iMac may have started after a software upgrade to 10.5.6 but I am not entirely sure.
    Thank you
    ajdk

    Well, you're current method sounds pretty good. But if you want to user a file server, hey go ahead.
    What you want to do when you centralize project files is to keep track of which one is the newest and becareful not to overwrite files with the same name. So you either have to set up individual spaces on the server (separate AFP/FTP folders maybe), or you'll need to run a file checkout service.
    The individual space is cheaper, but it's not much of a difference from backing up to the network drive. Since you have Gigabit connections, you might even opt to save ALL the user files on the server instead of just the project files.
    If you want to run a file checkout service, there's two approaches. You can run a service that can host any kind of file, or you can run a version control system for each kind of application (Photoshop, Word, etc.). Please notice, that as you read further and further along, the methods become more and more expensive and complicated. Once you get to this point, it will be necessary to purchase or build software in addition to the Mac OS X Server package.

  • Newb needs help w small office network setup

    Just started a new job at small start-up company that needs their 6-7 macs and a couple of printers networked. I'm just a designer and I'm trying to help but I'm not familiar with osX networking and I hope someone could point me in the right direction. Currently the owner has DSL on all the computers so there is an ethernet cable in each one to a router or hub i believe.
    Currently when I try to connect via Go menu to Connect to server, there is no list. If I type in the name of one of the other computers and try to connect I get:
    "Connection failed. The server may not exist of it is not operational at this time. Check the server name or IP address and try again."
    I don't really know where to start or what questions to ask but I hope having an ethernet cable system already in place is a good thing.
    Your help appreciated

    I'm starting out with 2 computers near me, G4 HOMER
    and G4 MINI. Both are connecting to the net via
    ethernet. Personal File Sharing is ON on both.
    On G4 MINI, I can see G4 HOMER, but when trying to
    connect (Go>Connect to server>G4 HOMER) get
    "ConnectionFailed -Server may not exist or is not
    operational"
    when connecting ot the server try using G4-HOMER.local as the server address.

Maybe you are looking for

  • How to delete a row of a template by giving a condition in the smartform

    hi all, I HAD A TEMPLATE IN A SMARTFORM. WHICH CONSISTS OF 4ROWS AND 4 COLOUMNS. MY REQUIREMENT IS . IF I SPECIFY A PARTICULAR PLANT(WERKS) CONDITION FOR EXAMPLE 2060. THE ENTIRE 4TH ROW WITH CONTENTS HAS TO BE DELETED. AND FOR OTHER PLANTS IT HAS TO

  • NOKIA n80 firmware update version v5.0725.0.1 APAC

    buddy i update my nokia n80 firmware from v5.0719.0.2 to v5.0725.0.1 APAC guys the new firmware has small fonts it is not good.further iam looking for other changes in log any news regarding EMEA version.hope nokia corrects this problem Solved! Go to

  • FLV embedded with Audio

    I'm creating flv files from videos which include audio which must remain. I'm creating the flv files using Sorensen codec as suggested before in Studio 8 for Flash 7 (company requirement). The flv files must be embedded since streaming is not an opti

  • Moan about screen resolution

    This is a general moan (hopefully Steve Jobs will read it and come up with a solution)... Like a number of other posters in this forum, I am finding the resolution of my new iMac 20" a real struggle. I want to display it at its natural resolution of

  • ITunes won't upgrade my 3GS.

    I'm wanting to go to 4.3.3, I'm at 4.2.1 but iTunes says that my system is up to date.  Am I doing something wrong?  I've updated before and never had this problem.  Thanks for any input.