SMC firmware update 1.3 safe with smcfancontrol?

Anyone know if it's safe to do the recent SMC firmware update 1.3 with smcfancontrol installed?
I'm running OSX 10.5.7 on a 15" MBP.
Thanks!

You might want to hang out in the MBP forum and check with those mavens.
http://discussions.apple.com/category.jspa?categoryID=250

Similar Messages

SMC firmware update 1.3 safe with smcfancontrol 2.2.2?

Anyone know if it's safe to do the recent SMC firmware update 1.3 with smcfancontrol installed?
I'm running OSX 10.5.7 on a 15" MBP.
Thanks!

Apple Expert on the phone today was not concerned at all with SMC Fan Control. I'll try it later though. Right now I'm backing things up in preparation for my trip to the store tomorrow. I suspect I was having SMC issues before and this update tweaked it some more. I've had the issue of the light on the magsafe adapter not working at all, (or always red, even when battery was charged) for so long that I stopped worrying about it. Did an SMC reset for that once or twice, but then never bothered as it didn't seem like that big a deal. Later I'll uninstall smcfancontrol and try the update again, but I think at this point I'm sol. The two techs I spoke to today were helpful, friendly and called me within a minute of sending my request. That's a good thing, at least.

Is the SMC Firmware Update 1.3 safe?

Hello all,
I have not installed that firmware 1.3 as I read one time it could be a problem. Searched here on the forum and don't see much about it just a lot about heat which is my problem as well.
I have a late 08 model. 17''
iStat says my left and right fan are at about 4400 rpm and my HD temp is 80 with just a browser open and watching say a flash video. Video and FCP seem always to be the culprit and wonder if this Firmware update will help.
THanks,
Al

I read one time it could be a problem.
Did you read this on an official Apple website?
Any "non-safe" Apple software will be pulled from Software Update or an update patch added.
wonder if this Firmware update will help.
You won't know until you install it.

Problem with SMC firmware update.

I can't seem to run it. Everytime I go to, it never installs. I have a feeling that it has to do with bootcamp. Whenever I restart my computer, it runs Windows (I don't know how to fix that.) so I can't just press restart, I have to actively start OSX.
I go to install it, my computer starts up, and then the installer pops up again. I press restart, start up the computer, same thing. I've done this 4 or 5 times and the same thing happens everytime. What should I do?

Sheir,
Go to System Preferences>Startup Disk and verify that OS X is the Startup OS that is selected for your Mac. If it is not the one selected, select it and restart your Mac a couple of times to verify that it will restart into OS X. If it won't then we need to figure out what is going wrong.
If it successfully restarts into OS X then go to Applications>Utilities and look for the SMC Firmware Update.app that should have been placed there and trash it. Also trash the SMC Firmware Update.dmg if you have it. I don't think you will because Software Update has been doing the install. Empty the trash.
Then go to Apple Downloads and manually download a fresh version of the iMac (early 2006) SMC Firmware Update released on 16 MAY 2006.
Shut down all your other programs except the Finder and Dashboard. Unplug everything from your Mac except your USB keyboard and mouse. Turn off Airport and Bluetooth if they're on.
Make sure you are completely familiar with the SMC Firmware installation instructions.
Try to do the install again.

Having problems with SMC Firmware Update 1.8

I installed the MacBook Pro SMC Firmware Update 1.8 yesterday and have since experienced a number of problems. I am running a 15 inch, Mid 2012 MacBook Pro, btw. First, after the intial install the sytem would not reboot. I had to do a physical reset of the SMC controller to get the system to power on again (sft-cntl-option-power key sequence). Once the system rebooted, the fan in stuck on high and the battery meter in the controll bar does not show status, just displaying an "X" in the battery. I went into the Software Update utility and the SMC update is still listed as available, I tried reinstalling it, and the situation has not changed. The fan noice is annoying and I'm aftraid to disconnect the laptop from the AC adapter. Please advise.
-cp

Firmware updates don't affect to Windows and OS X. The firmware makes your hardware work, not the operating system, so you won't have any problem doing this

Mac Pro SMC Firmware Update "An Unexpected Error Occurred (0)" HELP

Mac Pro SMC Firmware Update (Version 1.1) Size (970 KB)
"The SMC Firmware Update adjusts fan behavior in Mac Pro. The updater application will be installed in the /Applications/Utilities folder and will launch automatically. Please follow the instructions in the updater application to complete the process."
-----THIS IS WHAT HAPPEND TO ME----I try this morning to install and this is what I got:
" An unexpected error occurred (0).
Your firmware can not be Updated. "
"See www.apple.com/support for more information."

Are you booting from RAID? even though it warns that you can't be booting from RAID, some people still run the update.
Any problem with your system?
While it only says that you need to quit any and all open programs, sometimes it helps to reboot (and boot into Safe Mode) just to begin the process.
When there was an SMC Firmware update before (last fall) some people also had trouble.
We aren't mind readers, and to say it failed doesn't give those of us reading this (and non of us are Apple tech support) a lot to go on.
+Please follow the instructions in the updater application to complete the process.+
+To update the SMC firmware on your Mac Pro:+
+Your computer’s power cord must be connected and plugged into a working power source.+
+1. Quit all other open applications.+
+2. Click Restart in the Mac Pro SMC Firmware Update window and wait for your computer to restart.+
+The SMC firmware update starts automatically. A status bar indicates the progress of the update. During the update your computer fans will run at full speed, but will return to normal once the update completes.+
+Important: Do not interrupt the update.+
+Your computer restarts automatically when the update is completed and opens the Mac Pro SMC Firmware Update.+
+3. Click OK. The SMC firmware is now up-to-date.+
+If these instructions appear on your screen again, the SMC firmware update was not successful. Repeat steps 2 and 3.+
Note:
+This update requires a Macintosh formatted disk or partition. If you are starting up using a RAID (Redundant Array of Independent Disks) subsystem, you must attach a Macintosh formatted storage device to apply this update.+
*+Some USB and FireWire devices may prevent firmware updates from installing correctly.+*
*If you are having trouble installing an update try disconnecting non-essential devices and use only an Apple branded keyboard, mouse and monitor.+*
http://www.apple.com/support/downloads/macprosmcfirmwareupdate11.html

SMC Firmware Update Locks my mini

I got an auto update for SMC Firmware Update for my Mac mini [early 2006 w intel solo].
After running the auto - uptater it asked me to restart my computer. Once I did, my mini will not respond but the SMC Firmware Update looks to be running.
I have done the following:
• Made sure my mouse and keyboard work. They do but the mouse cannot click on anything - just move around.
• Tried to command-Q - doesn't work.
• Restart - doesn't work.
• Tried to restart with holding down the power button. Got the flashing power light and tone but - doesn't work.
• Tried force quiting with command-option-escape - doesn't work.
• Tried looking for some form of support out there - doesn't work.
Can anyone out there give me a hand?

I am in the same situation - am presently running under "safe boot". It´s the only way to communicate with the **** box! Have tried numerous attempt to let the machine restart, and left it as long as a day in this state, in case there is something going on in the background, but in vain.
So far it always looses contact after the initial boot, with the screen looking "dumb hazy blue".
Is there a way to uninstall the SMC Firmware Update -anyone??
And, by the way - to call this issue solved with the given resolve - isn´t that a little like telling a man with a broken leg that he should see a doctor?
Mac Mini Mac OS X (10.4.6)

SMC Firmware Update 1.1

SMC Firmware Update 1.1 just showed up in my software update. First off, I think I already have the latest:
Boot ROM Version: MP11.005C.B04
SMC Version: 1.7f8
Secondly, I am very chicken to run any firmware updates dealing with "The SMC Firmware Update adjusts fan behavior in Mac Pro." My fans are completely quiet.
Please let me know if I should install this.

I ran it on my octa-core. Everything seems fine. It'll restart, all fans will ramp up to full, then restart again and perform a normal boot. I checked my idle fan speeds before and after the update and they are all the same. I ran some cpu intensive tasks and the temp at which they ramp up doesn't seem to be much different. I use smcFanControl to boost my fans anyway as they don't start ramping until one of the cores gets over 200 degrees which is quite hot IMO.

Error while trying to install SMC Firmware Update

I have 2 original model 13" MacBooks doing the spontaneous shutdown thing. Both are running OS 10.4.11. One has SMC version 1.4f8, the other has SMC version 1.4f10. When I run software updater it comes up with 2 updates: MacBook EFI Firmware Update 1.0, and MacBook SMC Firmware Update 1.1. The first time I used the standard method of clicking on "Install 2 Items", etc. When the restart instructions came up, I clicked on restart, entered the password, and got the message: "An unexpected error occurred (0). Your Firmware cannot be upgraded."
I tried again, only I selected just the SMC update instead of both. Same result. I downloaded the package and tried to install directly instead of going through Software Updater, same result. I tried installing the EFI update by itself using different methods. Same result. Using advice from another thread, I tried opening the firmware updater application directly from the utilities folder. Still get the same error.
Anyone have any additional suggestions?

I have 2 original model 13" MacBooks doing the spontaneous shutdown thing. Both are running OS 10.4.11. One has SMC version 1.4f8, the other has SMC version 1.4f10. When I run software updater it comes up with 2 updates: MacBook EFI Firmware Update 1.0, and MacBook SMC Firmware Update 1.1. The first time I used the standard method of clicking on "Install 2 Items", etc. When the restart instructions came up, I clicked on restart, entered the password, and got the message: "An unexpected error occurred (0). Your Firmware cannot be upgraded."
I tried again, only I selected just the SMC update instead of both. Same result. I downloaded the package and tried to install directly instead of going through Software Updater, same result. I tried installing the EFI update by itself using different methods. Same result. Using advice from another thread, I tried opening the firmware updater application directly from the utilities folder. Still get the same error.
Anyone have any additional suggestions?

Macbook (late 2006) RSS unable to install SMC firmware update

Hello,
I bought my macbook on the 27th of December, and the first week it worked fine. Then started the RSS. I did some googling and found out some stuff about RSS, tried to install the SMC firmware update but it would just tell me that I don't need the update. After two weeks of constant RSS:ing I called applecare and told the guy about the problem, he told me to try to update the SMC and if I can't do it bring it in for service.
Monday the 15th of January I went to the macstation in downtown Vancouver and told them about the trouble, they tried to boot it, and it actually booted but after like 3 minutes the macbook crashed. For about 10 minutes two guys tried to boot it and so on, but they didn't get it to boot. So they took it in for service and somebody was going to check out the macbook and see if it would need a replacement logic board - which it did. So on Monday they ordered the logic board, and today Monday 22nd of January I got it back. Now the thing that bothers me is that when I now try to update the SMC firmware (my current version is btw 1.13f3) it still just says that This computer does not need this update. oh well - i went to apples support page to try to see if there would be a newer release of the smc and then I noticed that in the bottom of the SMC firmware 1.1 update page it says:
Note: This update is only or the original MacBook, and will not install on a MacBook (Late 2006).
Then I really was like W T F?!
I would assume that people who work for apple would know that the SMC update will not update on a computer from late 2006, but nobody ever mentioned this to me.
I've now had the computer for about an hour and the CPU temperature is at about 50 degrees celcius, with firefox, msn and a terminal open... about 5% cpu load.
What I'm really wondering is that is there anyone who has similar problems with a macbook late 2006? I guess I'll just have to see if it works and just like I told the guy at macstation, if it starts RSS:ing again I'll be banging on their door
macbook 2,1 Mac OS X (10.4.8) rss, unable to install SMC firmware update
macbook 2,1 Mac OS X (10.4.8) rss

See if reviewing the installation instructions provides any help:
http://www.apple.com/support/downloads/macbookefifirmwareupdate10.html

Mac Pro SMC Firmware Update 1.1 keeps repeating

Recently I had my MacPro motherboard replaced by an Authorized Repair Center, and for the most part, everything has been working great since. That said, as I've been performing my regular software updates, I've noticed that the "Mac Pro SMC Firmware Update 1.1" keeps appearing as new update. I've installed this update multiple times now (or it seemed as though I did), but it keeps appearing with each new update.
Is there some way I can complete the update? Is it possible that there is some serial number conflict between my old/new motherboard that is preventing this? Do I need to return my machine to the repair center?
Thanks for any help.

Did you actually run the update from your Utilities folder (where I believe it ends up)? You'll go through a process of rebooting and hearing the long tone / seeing grey screen and progress bar. Until it's actually run properly, you'll keep seeing reminders.
Matt

MacBook Pro SMC Firmware Update 1.3 update freezes mouse pointer

After installing the update released today 5/28 (MacBook Pro SMC Firmware Update 1.3) my mouse pointer stalls, freezes on occasion. Very annoying. Anyone seeing the same. Fixes ... ?

After applying the SMC Firmware update a few days ago, my keyboard and trackpad were acting erratic (freezing, hanging). It was immediately after the update and I had not had any problems with it before.
I have also had random crashes, inability to use the keyboard/trackpad ever since.
Today my keyboard and trackpad are completely unusable, external mouse works fine.
I will take it to an Apple store tomorrow, hopefully my firmware can be reverted.
Sounds like a lot of other people are having problems with this update. http://discussions.apple.com/thread.jspa?messageID=9549034&tstart=0#9549034

Recent smc firmware update......

it's not that i'm having any problems and really don't expect to, however, i'm a little concerned about the new update. i know it may stop rsd from occurring, but at what expense. is it simply disregarding a malfunction that is actually taking place, so that in time something more sever may occur.
it's only a concern that i haven't heard on here yet, although i would like to hear what people's opinions are.

I myself have installed it and have not had ay problems...
Here is something that I found for you.
"MacBook SMC Firmware Update 1.1
About this update
The SMC Update improves the MacBook’s internal monitoring system and addresses issues with unexpected shutdowns. This update is recommended for all MacBook systems, including those that received warranty repair."

Is SMC Firmware Update necessary?

Hello there
I have the Software Update window popping up telling me to download the SMC Firmware Update. I know that the update adjusts the fan behavior in the MacBook but does anyone know exactly what it does and changes?
My MacBook has been working fine since I got it in July. No weird fan behavior nor RSD nor overheating problems (thankfully! I'm hoping it stays that way). So my question is do I need that update, or is that update only for users with those problems? If I download it, how does it alter my MacBook behavior?
Any advise is appreciated! Thanks in advance.

Honestly I was kind of like you. I downloaded the firmware but didn't install it for quite a while. My MacBook as worked fine and I saw no reason to screw that up.
But..... it got the better of me and I went ahead and installed it. I haven't noticed any difference whatsoever. Fan behavior is the same I guess because I've only heard them a couple of time so that's never been an issue. I guess it may run a little cooler but again I don't really pay that much attention to the temperature anyway so I'm not sure.
SMC is System Management Controller which is a micro-controller on the logic board that controls various functions (in this case the fan). I've never found anything specific other than some have said the fans run non-stop. Could be but I've experienced nothing different than before I installed the firmware.

MacBook Air SMC Firmware Update v2.0 update available again and again. How do I fix it?

I have installed MacBook Air SMC Firmware Update v2.0 three times and I still get an update available notification asking to install it again. This is a mid-13 MacBook Air running OSX 10.9.3. System info lists the SMC version as 2.13f7.
Does anyone know how to resolve this issue?

Hi,
- Are there any status or error messages in /var/log/install.log
- The Firmware version it should install is 2.12f137
- If there isn't anything in the log try:
Intel-based Macs: Resetting the System Management Controller (SMC)
and/or About NVRAM and PRAM
and check whether there is installation.
If no install, try OS X: What is Safe Boot, Safe Mode
then reboot normal, try the install again.
Hope this helps

SMC firmware update 1.3 safe with smcfancontrol?

Similar Messages

Maybe you are looking for