Smooth radio sound not correct

Anyone else have this the sound on smooth radio stuttering, the sound is fine on all other channels.

Hi Daniel,
Is this still a problem? Sounds like the speed of your connection is causing this. Did you try and run a speed test?
ta
Craig
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
td-p/30">Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Similar Messages

Installed Flash update & now BBC radio sound & not able to buy on Amazon- Adobe Flash Plug in crashes, not sorted on re-load or re-install..

Was asked to unpdate Flash which I did, but now I cant get BBC radio sound or Amazon transactions.
Tried to re-install Flash & Firefox but not change

There have been issues reported with the 13.0.0.182 version of the Flash plugin crashing on some older Mac computers due to the compiler generating incompatible code.
The way to recover is to uninstall the Flash 13 version and revert to an older Flash version and wait for Adobe to release an update that addresses this issue.
* http://helpx.adobe.com/flash-player/kb/uninstall-flash-player-mac-os.html
You can either install the latest Flash 11.7 version that has the latest security updates (may not work with Safari) or the last Flash 12 version that didn't get the security updates Flash 13 has.
* http://www.adobe.com/special/products/flashplayer/fp_distribution3.html
Adobe Community: ATTENTION MAC CUSTOMERS - Flash Player 13 "Plugin Failure" Workaround:
* http://forums.adobe.com/thread/1447282

Notification sounds not correct

I thought I posted this earlier this week, but it's nowhere to be found, so here it goes again. I have an iPhone 5 with iOS 7, but this problem started with my iPhone 4S and has continued. All of my notifications play the correct sound, except for Facebook and Twitter. When I receive a Facebook notification, no sound at all plays (except for when I receive a Facebook message). This started after I did an iOS update (not a major one) on my 4S. I have the sound for Twitter notifications set to "Tweet," but it plays the "Tri-Tone" sound instead -- which was also the case on my old iPhone. I have gone in and changed the settings to a bunch of different tones, then back to the ones I want, but to no avail. Any help is appreciated, thanks!

Hey, were you able to come up with ANY info on this problem?
i have had this problem since i got my iphone5 in february/2013, and its continued onto my new iPhone5S.
The best i could come up with, through research and first-hand experience is that the "Facebook" and "twitter" tone options DO work, but only when it is an OUTGOING action YOU PERFORMED (ie a tweet that YOU posted, or a facebook post that YOU posted)
and since newer iphones have facebook and twitter integration, The facebook and Twitter tones also work for facebook Chat/messages that you receive, and twitter direct/instant messages that you receive.
As for the other types of notifications that you get from facebook and twitter (ie. Wall posts,being tagged in photos, twitter mentions/@replies, or notifications from people you are following{if turned on})
:::these notifications seem to fall into the same category of MOST notifications from ANY App that you download from the app store.
It seems thats MOST apps do not have a specific notification sound programmed, and ANY notifications that you have selected to receive are carried out with a "default" Apple Notification tone (which appears to be the classic Tri-Tone).
I have arrived at this conclusion because in the Settings->Sounds menu, only Device Functions are listed and thus able to have their Tone Changed.
ALSO; in Settings->Notification Center, You will notice that when you click on the various 'apps' listed:
*****'Stock' Apps (Messages, Phone, Facetime, Reminders, Calender etc.) have sub-options to change the name of the 'Sound' 's Tone (which appears there)
*****while ALL OTHER Downloaded apps only have a sub-option slider/knob to turn the 'Sound' either 'ON' or 'OFF'
Since there is no option to select a 'Tone' then it is safe to assume that the activated 'Sound' is the Device's default tone.
THEREFORE...if there is no options -WITHIN THE APPLICATION ITSELF- to change the Sound or Tone of their Notifications...the question/objective Now seems to be: How can we change our Device's default Notification Sound?
<Edited by Host>

Radio sound not coming through - Nokia 6120

Yes, I have checked other topics before posting and yes I have the headset plugged in.
I am angry! The scroll buttons wont change the frequency. I did it manually then chose the listen option and no sound! What am I doing wrong?

It could be that your recording is in MPEG-2 format, which seems to be common among hard drive camcorders, and you require the MPEG-2 codec (available from the Apple Store).

Why does my new garageband 10.0.03 not have the legacy with sound effects or radio sound preset or applause preset???? I need these to be able to chop samples into the keyboard keys by dragging and dropping them into the keys.

I am just trying to chop samples and drop them into a track with legacy-sound effects- radio sounds, so that I can play with them and chop them onto keys. I see a bunch of videos on youtube showing you how to do it, but I can't find those kits on the newest garageband.

All these effects are part of the loops in the iLife Sound effects loop package, that was a part of the application bundle iLIfe '11 (iPhoto. iMovie, GarageBand '11). These loops are neither installed by GarageBand 10.0 or GarageBand '11, nor MacOs X, you need an iLife '11 installer disk to get these loops.
And GarageBand 10 also does not have the Sound Effects instruments any longer, that let you drag samples onto keys. It is one of the sorely missed features, that have been discontinued in the new version GarageBand 10. even if you install the previous version, GarageBAnd '11, to add the Sound effects instrument to GarageBand 10. it will not work properly, because GarageBand 10 will not save the custom instrument with the samples. You will have to complete your song in one session, without quitting GarageBand.
You may want to send feedback to the Apple Developers about these missing features with a feature request: Apple - GarageBand Mac- Feedback

My G5 is not booting up and it sounds like an airplane taking off. I replaced the 3.6v battery, but did not correct the problem. Any suggestions?

My G5 is not booting up and it sounds like an airplane taking off. I replaced the 3.6V battery, but it did not correct the problem. Any suggestions??

Resetting the Logic Board
Resetting the logic board can resolve many system problems. Whenever you have a
unit that fails to power up, you should follow this procedure
before replacing any modules.
1 Unplug the computer.
2 Press the Power On button on the front of the unit.
3 Open the side access panel.
4 Remove the battery from the logic board.
5 Wait at least 10 minutes before replacing the battery.
6 Make sure the battery is installed in the correct +/-
direction.
7 Reassemble the computer and test the unit.
 Cheers, Tom

How do I correct the "Wireless Radio is not working" problem on my Photosmart C410 Printer?

HP Photosmart Prem C410a All-in-One
Windows 7 64-bit
Wireless Radio is not working
Trying to change from USB to wireless setup
purchased at Staples on 8/19/2010 - means warrenty has expired

With the printer ON, unplug power from the back of the printer for 30 seconds. Does that reset the radio?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

WRT54G v 7.0 -- Setting "Keep Alive: Redial Period" not correct (radio button)

Hi,
I own a Linksys-Router WRT54G v7.0 with firmware v7.00.8 build 008, Jul. 9, 2009.
On the web GUI (Setup/Basic Setup) there's a setting "Keep Alive: Redial Period XX Sec.". As I'd like to stay connected with my provider permanently, I've set the radio button to "Keep Alive: Redial Period" and the according text field to "30" seconds. Then, I've clicked "Save Settings" and got a confirmation message that the settings got saved.
Anyway, even after saving the settings the according radio button is still set to "Connect on Demand...". But that is only true for newer browsers, like e.g. IE8, IE7 or Firefox 8. If you use an older browser, like e.g. IE6, then the radio button is correctly set to "Keep Alive: Redial Period" with a value of "30" seconds.
Conclusion: The settings get correctly saved by the router (I can confirm that), but they don't get correctly shown in the web GUI. Looks like a HTML/Javascript bug in the router's admin web GUI. That's really annoying as you never exactly know the effective settings...
Can someone confirm that bug? Is there a newer firmware than version 7.00.8?
Regards,
Patrick

Try to clear the browser's cache as well.
"Don't fix it if it ain't broken."

The radio is not working in my ipod nano, and has the correct zone, how can I make it work?

I bought the new Ipod nano, and the radio is not working. I live in the USA, and has being setting in "America" zone, but is not working!! I plugged the headphones, and I tried in different places, and I not working!!!
What could I do?

Check if the headphones are inserted all the way in till you hear a click. Hope this helps!

ITunes RADIO is not working. "iTunes could not connect to the iTunes Store. Make sure your internet connection is active and try again." Try as I may, as many as ten attempts, trying to connect after restart, after shutdown, nothing works. Just so - iTu

iTunes RADIO is not working.
“iTunes could not connect to the iTunes Store. Make sure your internet connection is active and try again.” Try as I may, as many as ten attempts, trying to connect after restart, after shutdown, nothing works. Just so …
iTunes STORE not “connectable” with my otherwise perfectly-working internet connection, viable, up and running for all other uses.
Simply put, firstly, I can't connect to the internet when I click on Radio. People are quite suspicious that this is Apple incompetence or your company's famous arrogance for this commonly-suffered problem that you won't or “can’t” fix.
Read the many web comments and you won’t be pleased with yourselves: the suspicion is that if you ruin internet radio on iTunes, Apple will somehow make more money on music downloads, etc. Bull.
Also, thirdly, my old playlist of 20 or so internet radio stations in the Ambient category STILL PLAYS !
Then fourth, I installed the latest available version of QuickTime Player 7.app Version 7.6.6 but it didn’t solve the problem either. I had QuickTime Player.app Version 10.2, but substituted what Apple website said was the latest, LOWER NUMBERED QuickTime Player version of 7.6.6
Fifth, I can't connect to iTunes store no matter what I do or what user group's advice I try. So I can’t buy or download anything from iTunes. Bad for business.
Sixth, I updated to the latest version of iTunes but this weird problem remains. All suggested Apple fixes or user group fixes are useless. Where is Apple’s famous technical competency, vaunted customer support?, and user-friendly product reputation? Get it back, please.
Solve this problem of yours ASAP for us, your numerous disgruntled, dissatisfied customers of iTunes. You can do better, should, and really –in all fairness- must.
===============================================================
NOTE: no password for iTunes exists in my Keychain. Is this a problem?
Apple ACCOUNT ID, and iTunes ID password, works but not to access iTunes with my healthy internet connection.
Apple store id It works via direct internet connetion but not through iTunes. Very strange.
===============================================================
FYI, Hardware Overview:
Model Name:                       MacBook Pro
Model Identifier:                 MacBookPro8,2
Processor Name:               Intel Core i7
Processor Speed:               2 GHz
Number of Processors:    1
Total Number of Cores:    4
L2 Cache (per Core):         256 KB
L3 Cache:                            6 MB
Memory:                              16 GB
Boot ROM Version:            MBP81.0047.B27
SMC Version (system):      1.69f4
Serial Number (system):   C0*******F8V
Sudden Motion Sensor:
State:   Disabled
Intel 6 Series Chipset:
Vendor: Intel
Product:            6 Series Chipset
Link Speed:       6 Gigabit
Negotiated Link Speed:           6 Gigabit
Description:      AHCI Version 1.30 Supported
M4-CT512M4SSD2:
Capacity:           512.11 GB (512,110,190,592 bytes)
Model: M4-CT512M4SSD2
Revision:           040H
Serial Number: 0000000012330912E75A
Native Command Queuing:    Yes
Queue Depth:   32
Removable Media:        No
Detachable Drive:        No
BSD Name:         disk0
Medium Type:      Solid State
TRIM Support:     Yes
Partition Map Type:     GPT (GUID Partition Table)
S.M.A.R.T. status:         Verified
Volumes:
disk0s1:
Capacity:           209.7 MB (209,715,200 bytes)
BSD Name:         disk0s1
Content:            EFI
disk0s2:
Capacity:           511.25 GB (511,250,432,000 bytes)
BSD Name:         disk0s2
Content:            Apple_CoreStorage
Recovery HD:
Capacity:           650 MB (650,002,432 bytes)
BSD Name:         disk0s3
Content:            Apple_Boot
Volume UUID:   600737FB-7A29-3BAE-859E-CBFE2E90C39A
<Edited by Host>

This my sound too simple, but I just kept clikning on the arrow next to the selected music and it finally "Kicked" in.
I live in Europe ,So Be persistent and don't give up ! Aug. 2013

AUDIODG.EXE hogging 80-100% of CPU and sound not working in Vista . . .

I posted this on a Microsoft Answers Forum but none of the techs or people reading have been able to help so far. I'm dying to get to the bottom of this:
Here is my computer:
MSI K8N Neo4 Platinum
AMD Athlon 64 3000+
2GB RAM
XFX GEFORCE 6600 GT 128MB DDR3 DUAL DVI & TV OUT (PCI-E)
200GB WD SATA HDD
500GB WD HDD in external enclosure via USB2
NEC ND-3520A 16X DVD±RW Dual Layer DVD Burner
LG CD Burner
I've been using Vista Home Premium successfully for some time. Recently, not too long after I did a clean wipe of my OS, my audio would stop working. The way it would happen is that everything would work fine until I started iTunes or another audio application and when I would hit play, things would lock up.
Upon inspection of my system resources, I'm noticing that the audio platform for Vista, via the audiodg.exe, is using close to 100% of my CPU resources, even when the computer is making no sound at all.
I've had a Sound Blaster Live! card in my computer for some time but I was not using it; I use the Realtek AC'97 audio drivers that are on my motherboard instead. I thought that the conflict may be the computer wanting to recognize my Sound Blaster, so I took it out of my computer but the problem seems to be worse.
Are there any BIOS setting that need to be adjusted for my sound to start working again?
I'm very reliant on the audio processing power of my computer (I'm in the radio industry, part-time) and this is a huge drag on my productivity.
Any tips would be much appreciated.
REPLY #1:
Thank you for using Microsoft Answers forum. I suggest going to the manufacture of your sound card and download the latest drivers and install them.
MY RESPONSE:
Good suggestion. The problem is this:
I am running on-board audio. I have an MSI K8N Neo4 Platinum motherboard which runs "Realtek ALC Series AC97 Audio Driver" and there is no version for Vista. They have a version for Windows 2K/XP and one for Windows XP 64bit.
Should I use on of those and if not, then what?
UPDATE (from me):
I took a chance and found a Realtek AC'97 driver for Vista.
http://drivers.softpedia.com/progDownload/Realtek-AC-97-Audio-Codec-Driver-Vista-6183-Beta-Download-18114.html
I went to install it and the install hung. So, I closed one of the install windows and then the InstallShield app continued like it was working. So, I hit "Restart my computer". Well, the reboot hung too. So, I reset the PC manually.
When the computer came back up, the sound worked. Hard to tell if this will fix it for good but it's promising. Chaotic. Unpredictable. Annoying.
REPLY #2:
Before you tried updating drivers, did you try rebooting 1st?
I'm just trying to determine if rebooting your system is what resolved the issue - thank you
UPDATE II (from me):
My computer is behaving the same way it was before. AUDIODG.EXE taking up 80-100% of my CPU and the sound not working.
Any other ideas?

Small update: Despite my intelligence, good looks and vast experience I use Google sometimes. To my surprise this file turns out to be a Windows one. Here is someone who is much happier, and since it is some way in my line of thinking I'll quote it, but you might take my previous advice as well:
http://forums.techarena.in/windows-vista-performance/1012315.htm
"- Open up msconfig.exe > Manage startup programs.
- Disable ALL Realtek entries
- Close msconfig.exe
- Right-click on the speaker icon > Audio devices > Speakers (properties)
- Go to the enhancements tab
- Check the box to disable all audio enhancements
- Close the menu
- Right-click on the speaker icon > Recording devices
- Disable all your microphones (yeah..., the actual problem seems to come
from voice inputs rendering..)
- Close the menu
- Restart your computer"

Wireless radio is not functioning - Photosmart c4599 All-in-one

I have had my printer connected to my home wireless network. The printer stopped working. When I run the wireless network test report it says "The wireless radio is not functioning. Contact HP Support. According to the HP web site, the printer is out of warranty. Is there anything I can do to get the wireless working again via a hard reset or is this something a technician will need to fix? If out of warranty, is the cost to fix really worth it?

If this message is appearing on the Front Panel of the printer, then it is an indication of a hardware problem that has developed.
It sounds like the wireless card has gone bad in the printer and this is not something that a reset would be able to address.
If the printer is out of warranty, then your best option is to replace the printer. HP Tech Support has many options available to you, such as the Upgrade program.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Wireless Radio is not functioning on Photosmart C309a

VERY FRUSTRATED right now....I've read similar posts about this and wonder if there is a significant flaw with the wireless radio in this model that HP will not acknowledge....
I've got a 13 month-old (Still shiny new) Photosmart C309a that is just past the warranty date. It really hasn't been used much at all -- just basic household use. I am totally kicking myself since we started having problems with the wireless network disconnecting about 3-4 months ago (when it was still under warranty). It was a sporadic issue, and I was always able to do a reconnect by doing a combination of unplugging it and then using the "Wireless Setup Wizard" to reconnect. Now it cannot find the wireless network at all. The Wireless Radio is "on" and when I run the Wireless Network Test I now get "The Wireless Radio is not Functioning. Contact HP Support". My wireless network seems to be working just fine for everything else, so I truly think this is a printer problem.
Anyhow, because it is just past warranty, we have called HP support twice and have not gotten much help either time. They do not seem to care and tell you they will have to charge you for the help?!?
Am I supposed to replace a perfectly good printer since the wireless doesn't seem to connect? Is there another way to fix this? Is there a way to just replace the wireless radio and not the whole printer (and is that advisable)?
I would greatly appreciate any help!

This seems to be an issue with HP wireless printers. The Photosmart C309a is my second all in one in 5 years. Same as many others, my wireless went dead 13 months after purchase with very light home use. Last one had wireless go dead same way and had to use it wired to the network for 4 years.(except for wireless, old printer still works fine, had to upgrade for Windows 7)
Seems HP should correct this issue or at least quit advertising wireless printers when the wireless dies and cannot be fixed.
No one should have to purchase a new all in one printer to have wireless when everything works except the wireless after the first year. The printers cost way too much for cheap wireless with a short lifespan. If HP does not do a recall on these printers for the wireless, I'm going to purchase a different name brand next time... Starting to look up reviews now on other printers.

RAP Running flex+bridge back haul A radio will not turn on

Hardware: WLC 5508 running latest Software Version 8.0.100.0
AP Code : c1550-k9w8-xx.153-3.JA
Description :Whilst running in flex+bridge mode and configured as a Root AP, the RAP back-haul A radio will not change to operationally UP.
If the AP is changed to be configured as a MAP, the A radio back haul will go operationally UP.
Debug of the AP below and screenshot of the WLC has been attached.
flashfs[0]: 38 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10195456
flashfs[0]: Bytes available: 21673472
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
IOS Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 38 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10195456
flashfs[0]: Bytes available: 21673472
flashfs[0]: flashfs fsck took 5 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Boot CMD: 'boot flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
Initializing flashfs...
flashfs[2]: 38 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31610880
flashfs[2]: Bytes used: 10195456
flashfs[2]: Bytes available: 21415424
flashfs[2]: flashfs fsck took 6 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 5806080
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 5805056
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8364B 8000 A8020000 0 A8030000 30
Rate table has 336 entries (20 legacy/64 11n/252 11ac)
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
Radio1 present 8364B 8000 B8020000 0 B8030000 13
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1824P030
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from unknown reload cause - ptr to non-ascii bytes 0x17
LWAPP image version 8.0.100.0
4 Gigabit Ethernet interfaces
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: B0:00:B4:61:A2:20
Part Number : 73-13538-02
PCA Assembly Number : 800-31224-01
PCA Revision Number : 03
PCB Serial Number : FOC18159782
Top Assembly Part Number : 800-38848-03
Top Assembly Serial Number : FTX1824P030
Top Revision Number : A0
Product/Model Number : AIR-CAP1552EU-N-K9
% Please define a domain-name first.
Spanning Tree protocol for Bridge Group 1 has not been configured.
Press RETURN to get started!
*Mar 1 00:00:08.551: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:09.311: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
*Mar 1 00:00:09.311: Registering HW DTLS
*Mar 1 00:00:09.751: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:11.547: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:12.415: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:15.279: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:15.471: AP Mesh platform identified (backhaul config:0x2, access:0xF)
*Mar 1 00:00:15.535: Starting Ethernet promiscuous mode
*Mar 1 00:00:18.103: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
*Mar 1 00:00:18.103: %SNMP-5-COLDSTART: SNMP agent on host APb000.b461.a220 is undergoing a cold start
*Mar 1 00:00:19.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.019: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 00:00:20.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:21.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:22.151: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:22.191: Starting Ethernet promiscuous mode
*Mar 1 00:00:22.355: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:22.355: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:36.591: Currently running a Release Image
*Mar 1 00:00:36.603: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:41.019: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:00:41.023: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:41.031: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
*Mar 1 00:00:41.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:42.115: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
Not in Bound state.
*Mar 1 00:00:42.123: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:43.031: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:43.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:43.223: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:44.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:00:46.067: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.067: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:46.103: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.144, mask 255.255.255.192, hostname APb000.b461.a220
*Mar 1 00:00:46.103: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.103: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:51.143: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 1 00:00:51.211: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
Translating "CISCO-CAPWAP-CONTROLLER.bla"...domain server (10.207.15.11)
*Mar 1 00:00:51.211: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:52.207: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.229 obtained through DHCP
*Mar 1 00:00:52.207: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.230 obtained through DHCP
*Mar 1 00:00:52.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:52.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:00:52.223: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:53.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:53.243: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:54.243: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 16 02:13:35.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:13:37.055: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:13:37.055: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
*Sep 16 02:13:37.839: %LWAPP-4-CLIENTEVENTLOG:
Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
*Sep 16 02:13:38.951: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 16 02:13:39.875: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
*Sep 16 02:13:40.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 16 02:13:40.243: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
*Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
*Sep 16 02:13:41.895: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
Writing out the event log to flash:/event.log ...
*Sep 16 02:20:51.675: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Recvd RESET req from Controller.
*Sep 16 02:20:51.687: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Write of event.log done
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 36 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10009088
flashfs[0]: Bytes available: 21859840
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
IOS Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 36 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10009088
flashfs[0]: Bytes available: 21859840
flashfs[0]: flashfs fsck took 5 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Boot CMD: 'boot flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
Initializing flashfs...
flashfs[2]: 36 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31610880
flashfs[2]: Bytes used: 10009088
flashfs[2]: Bytes available: 21601792
flashfs[2]: flashfs fsck took 6 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 5806080
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 5805056
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8364B 8000 A8020000 0 A8030000 30
Rate table has 336 entries (20 legacy/64 11n/252 11ac)
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
Radio1 present 8364B 8000 B8020000 0 B8030000 13
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1824P030
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from unknown reload cause - ptr to non-ascii bytes 0x18
LWAPP image version 8.0.100.0
4 Gigabit Ethernet interfaces
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: B0:00:B4:61:A2:20
Part Number : 73-13538-02
PCA Assembly Number : 800-31224-01
PCA Revision Number : 03
PCB Serial Number : FOC18159782
Top Assembly Part Number : 800-38848-03
Top Assembly Serial Number : FTX1824P030
Top Revision Number : A0
Product/Model Number : AIR-CAP1552EU-N-K9
% Please define a domain-name first.
Spanning Tree protocol for Bridge Group 1 has not been configured.
Press RETURN to get started!
*Mar 1 00:00:08.551: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:09.311: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
*Mar 1 00:00:09.311: Registering HW DTLS
*Mar 1 00:00:09.747: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:11.547: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:12.411: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:15.279: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:15.455: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:15.467: AP Mesh platform identified (backhaul config:0x2, access:0xF)
*Mar 1 00:00:15.535: Starting Ethernet promiscuous mode
*Mar 1 00:00:18.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
*Mar 1 00:00:18.087: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:18.463: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:18.531: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:18.735: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:18.739: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:19.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.011: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 00:00:20.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:21.495: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:30.559: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.147, mask 255.255.255.192, hostname APb000.b461.a220
*Mar 1 00:00:36.591: Currently running a Release Image
*Mar 1 00:00:36.603: Using SHA-1 signed certificate for image signing validation.%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:40.939: AP image integrity check PASSED
*Mar 1 00:00:40.947: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:41.027: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:00:41.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:42.127: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:42.135: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:43.127: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:43.235: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:44.235: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%Error opening flash:/capwap-saved-config (No such file or directory)
*Mar 1 00:00:51.047: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
*Mar 1 00:00:51.055: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:51.059: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:51.059: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:56.099: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 1 00:00:56.115: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
*Mar 1 00:00:56.115: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:57.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
*Mar 1 00:00:59.831: Starting Ethernet promiscuous mode
*Mar 1 00:00:59.839: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.229 obtained through DHCP
*Mar 1 00:00:59.839: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.230 obtained through DHCP
*Mar 1 00:03:15.031: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:03:15.031: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:03:15.031: %MESH-6-LINK_UPDOWN: Mesh station b000.b461.a23c link Down
*Mar 1 00:03:34.151: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:03:39.191: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 1 00:06:04.151: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 1 00:06:04.151: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 1 00:06:04.151: %MESH-6-LINK_UPDOWN: Mesh station b000.b461.a23c link Down
*Mar 1 00:06:23.271: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:06:28.311: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 35 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10014208
flashfs[0]: Bytes available: 21854720
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
IOS Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 35 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10014208
flashfs[0]: Bytes available: 21854720
flashfs[0]: flashfs fsck took 5 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Boot CMD: 'boot flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
Initializing flashfs...
flashfs[2]: 35 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31610880
flashfs[2]: Bytes used: 10014208
flashfs[2]: Bytes available: 21596672
flashfs[2]: flashfs fsck took 6 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 5806080
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 5805056
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8364B 8000 A8020000 0 A8030000 30
Rate table has 336 entries (20 legacy/64 11n/252 11ac)
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
Radio1 present 8364B 8000 B8020000 0 B8030000 13
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1824P030
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from unknown reload cause - ptr to non-ascii bytes 0x17
LWAPP image version 8.0.100.0
4 Gigabit Ethernet interfaces
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: B0:00:B4:61:A2:20
Part Number : 73-13538-02
PCA Assembly Number : 800-31224-01
PCA Revision Number : 03
PCB Serial Number : FOC18159782
Top Assembly Part Number : 800-38848-03
Top Assembly Serial Number : FTX1824P030
Top Revision Number : A0
Product/Model Number : AIR-CAP1552EU-N-K9
% Please define a domain-name first.
Spanning Tree protocol for Bridge Group 1 has not been configured.
Press RETURN to get started!
*Mar 1 00:00:08.539: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:09.299: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
*Mar 1 00:00:09.299: Registering HW DTLS
*Mar 1 00:00:09.731: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:11.527: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:12.395: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:15.263: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:15.451: AP Mesh platform identified (backhaul config:0x2, access:0xF)
*Mar 1 00:00:15.519: Starting Ethernet promiscuous mode
*Mar 1 00:00:18.083: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
*Mar 1 00:00:18.083: %SNMP-5-COLDSTART: SNMP agent on host APb000.b461.a220 is undergoing a cold start
*Mar 1 00:00:18.503: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:18.543: Starting Ethernet promiscuous mode
*Mar 1 00:00:18.707: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:18.707: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:19.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.011: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 00:00:20.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:21.495: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:36.571: Currently running a Release Image
*Mar 1 00:00:36.583: Using SHA-1 signed certificate for image signing validation.
%Error opening flash:/capwap-saved-config (No such file or directory)
*Mar 1 00:00:41.003: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
*Mar 1 00:00:41.011: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:00:41.015: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:42.107: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
Not in Bound state.
*Mar 1 00:00:42.115: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:43.023: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:43.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:43.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:44.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:00:46.043: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.043: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:46.095: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.147, mask 255.255.255.192, hostname APb000.b461.a220
*Mar 1 00:00:46.095: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.095: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:51.135: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 1 00:00:51.151: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
*Mar 1 00:00:51.151: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:52.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
*Mar 1 00:00:55.831: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.207.15.23 obtained through DHCP
*Sep 16 02:30:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:30:49.559: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:30:49.559: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
*Sep 16 02:30:50.759: %LWAPP-3-CLIENTERRORLOG: Load Reap Cfg failed, trying backup...
*Sep 16 02:30:50.775: %LWAPP-4-CLIENTEVENTLOG:
Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
*Sep 16 02:30:50.779: %LWAPP-4-CLIENTEVENTLOG: No REAP non-ap specific configuration file to load. Connect to controller to get configuration file
*Sep 16 02:30:52.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 16 02:30:52.223: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 16 02:30:52.651: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
*Sep 16 02:30:52.691: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
*Sep 16 02:30:53.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 16 02:30:53.243: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 16 02:30:53.867: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
*Sep 16 02:30:53.867: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 16 02:30:54.127: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Sep 16 02:30:54.871: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 16 02:30:55.895: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 16 02:30:56.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to upRename from flash:/lwapp_reap.cfg to flash:/lwapp_reap.cfg.bak failed, errorno = 2
*Sep 16 02:31:14.119: %CLEANAIR-6-STATE: Slot 1 disabled
*Sep 16 02:38:12.379: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 16 02:38:12.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 16 02:38:13.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 16 02:38:13.407: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 16 02:38:14.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 16 02:38:15.339: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
Writing out the event log to flash:/event.log ...
*Sep 16 02:38:24.375: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Recvd RESET req from Controller.
*Sep 16 02:38:24.387: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Write of event.log done
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 39 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10195456
flashfs[0]: Bytes available: 21673472
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
IOS Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 39 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 10195456
flashfs[0]: Bytes available: 21673472
flashfs[0]: flashfs fsck took 5 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: b0:00:b4:61:a2:20
Boot CMD: 'boot flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
Initializing flashfs...
flashfs[2]: 39 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31610880
flashfs[2]: Bytes used: 10195456
flashfs[2]: Bytes available: 21415424
flashfs[2]: flashfs fsck took 6 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 5806080
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 5805056
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.
Radio0 present 8364B 8000 A8020000 0 A8030000 30
Rate table has 336 entries (20 legacy/64 11n/252 11ac)
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
Radio1 present 8364B 8000 B8020000 0 B8030000 13
POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
Radio2 not present 0 0 0 0 0 11
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1824P030
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from unknown reload cause - ptr to non-ascii bytes 0x18
LWAPP image version 8.0.100.0
4 Gigabit Ethernet interfaces
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: B0:00:B4:61:A2:20
Part Number : 73-13538-02
PCA Assembly Number : 800-31224-01
PCA Revision Number : 03
PCB Serial Number : FOC18159782
Top Assembly Part Number : 800-38848-03
Top Assembly Serial Number : FTX1824P030
Top Revision Number : A0
Product/Model Number : AIR-CAP1552EU-N-K9
% Please define a domain-name first.
Spanning Tree protocol for Bridge Group 1 has not been configured.
Press RETURN to get started!
*Mar 1 00:00:08.563: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:09.323: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
*Mar 1 00:00:09.323: Registering HW DTLS
*Mar 1 00:00:09.759: m8349_ether_enable: MACCFG1 sync timeout
*Mar 1 00:00:11.559: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
*Mar 1 00:00:12.423: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
*Mar 1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
*Mar 1 00:00:15.291: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:15.479: AP Mesh platform identified (backhaul config:0x2, access:0xF)
*Mar 1 00:00:15.547: Starting Ethernet promiscuous mode
*Mar 1 00:00:18.119: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 13:50 by prod_rel_team
*Mar 1 00:00:18.119: %SNMP-5-COLDSTART: SNMP agent on host RAP is undergoing a cold start
*Mar 1 00:00:19.459: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.035: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 00:00:20.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
*Mar 1 00:00:21.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:22.163: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:22.203: Starting Ethernet promiscuous mode
*Mar 1 00:00:22.367: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:22.367: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:36.603: Currently running a Release Image
*Mar 1 00:00:36.615: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:41.023: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
*Mar 1 00:00:41.027: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:41.035: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
*Mar 1 00:00:41.043: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:42.119: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
Not in Bound state.
*Mar 1 00:00:42.127: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:43.035: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:43.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:43.227: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:44.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:00:46.051: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.051: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:46.107: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.149, mask 255.255.255.192, hostname RAP
*Mar 1 00:00:46.107: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar 1 00:00:46.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 1 00:00:51.147: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 1 00:00:51.211: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
*Mar 1 00:00:51.215: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:52.211: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.207.15.23 obtained through DHCP
*Mar 1 00:00:52.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:52.219: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:00:52.227: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:53.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:53.247: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:54.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 16 02:40:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:40:24.555: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
*Sep 16 02:40:24.555: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
*Sep 16 02:40:24.771: %LWAPP-4-CLIENTEVENTLOG:
Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
*Sep 16 02:40:26.219: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 16 02:40:26.227: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 16 02:40:26.443: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 16 02:40:26.595: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
*Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
*Sep 16 02:40:27.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
Regards,
Will

Australia and the AP seems to be in the correct country. The Operational Status is "REG" on both AP's.

My video recording sounds not working but other sounds are working fine, I've tried clearing the little mic thing near my earphone hole and had no success can someone please help me out?

hhi guys
my video recording sounds not working at all but it's working for other things such as music. I've tried to clear my sound thing near the earphone hole but had no success can someone please help me out?

Had an Iphone 4 for about 3 months now. This happened to the first one I had and they ended up having to replace it at the apple store just a couple weeks ago 6/2. It happened again last night to my new one. This time i was able to correct it by going to itunes, backing up the phone to icloud, and then restoring the software. Mine did not work with voice memo, but did work with headphones plugged in, and would also work on speaker. I could hear callers but they couldn't hear me. I had purchased a new case (lifeproof case at $79.99) because it comes with plugs that cover the headphone jack, and the charging port, and is also waterproof. I heard that the root cause is due to lint, dirt, etc getting inside the headphone jack. Well, must be something else. It's a 10 days old phone, and has been in this overpriced case the whole time, and I have not used the headphones. I hope this doesn't keep happening.

Smooth radio sound not correct

Similar Messages

Maybe you are looking for