Smtp error in a cisco SF300

I have a problem with a SF300-24 24-Port 10/100 Managed Switch. I want to use the Switch Port Mapper of oputils (manageEngine) and it doesn't bring me the info of the switch such as: vlans, MAC and the IP address of the devices connected in each port.
I get this error inthe log of the switch. "%SNMP-W-SNMPAUTHFAIL: Access attempted by unauthorized NMS"
I have another switch of the same model and it works well. The smtp configuration is the same (it has an older firmware)
Any idea of how I resolve this problem?

Hi Slotmashines,
I would recommend you to reapply SNMP settings but if the error reoccurs please open ticket with Cisco Small Business Support team:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Aleksandra

Similar Messages

How to setup a static multicast ARP entry with Cisco SF300-08?

We're running a cluster in multicast mode as a loadbalancer.
We have Cisco SF300-08 and when we adding a static ARP entry results in an error message telling the user that the hardware address needs to be a valid unicast MAC address.
So how to setup a static multicast in Cisco SF300 or maybe someone know other solution to setup multicastes mode in Cisco SF300.

Hi, Tom!
We have two watchguard xtm505(cluster active-active) in our network. Watchguard interfaces have one ip and one mac adresses. IP 192.168.111.1(Unicast) and MAC 01:00:5e:02:02:03(multicast). Cisco SF300 is router to outside networks(to internet). Cisco IP adresss is 192.168.111.254. There are another some hosts in this network.
Ping from hosts to 192.168.111.254 works well. Ping from hosts to 192.168.111.1 works well too. But there is no ping from watchguard cluster(192.168.111.1) to Cisco(192.168.111.254). And there is no routing to internet
This is well-known situation. We need to do following(example for cisco 3750):
1.    Start the Cisco 3750 command line interface.
2.    Add a static ARP entry for the multicast MAC address of the FireCluster interface.
Type this command:
arp arpa
For this example, type:
arp 192.168.111.1 01:00:5e:02:02:03 arpa
3.    Add an entry to the MAC address table.
Type this command:
mac-address-table static vlan interface <#>
For this example, type:
mac-address-table static 01:00:5e:02:02:03 vlan 1 interface gi1/0/11
But we can't add arp entry on Cisco SF300. CLI tells us "MAC address illegal"!
We tried enable igmp snooping, but is not helps.
Could you tell more detailed about MAC groups?

Trunking on Cisco SF300 Issue

Hello Friends,
Issue: I have 3 Cisco SF300 multilayer switches, I have configured one switch as a core switch and changed the mode to Router (from layer2 to Layer3) and configured Vlans and DHCP pools accordingly, but when i am trying to connect another SF300 to this switch by using VTP it's giving error then i tried searching a solution and found that it does not support VTP protocol, can someone please help me on that, how i can connect other SF300 to this core switch by using trunking.
My goal is to connect the Switch1 and Switch2 to the CoreSwitch by using trunking so that CoreSwitch can advertise all Vlan information to Switch1 and 2. and PC connected to Switch1 & 2 on different Vlans can communicate to each other.
Network Diagram:
CoreSwitch fast-Ethernet port 1 to 8 are connected to Huwai Router Port 1 to 8 using a dedicated physical enter phase to connect each Vlan to the internet. using Nat overload. CoreSwitch's fastethernet Port 9 to 24 are disabled, gigabit port 1 to 4 are trunk port and allowed vlan are 11, 12,13,14,15,16,17 and 20.
Note: All 3 switches are in Layer3 mode.
CoreSwitch Gigabit ethernet Port1 connected to = Switch1 gigabit ethernet port 1
CoreSwitch Gigabit ethernet Port2 connected to = Switch2 gigabit ethernet port 2
Switch1 Gigabit ethernet Port4 connected to = Switch2 gigabit ethernet port 4
Configuration:
CoreSwitch:
User Name:cisco
Password:XXXXXXX
Welcome to CoreSwitch.
Regards,
Sandy
CoreSwitch#show run
config-file-header
CoreSwitch
v1.3.7.18 / R750_NIK_1_35_647_358
CLI v1.0
set system mode router
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
spanning-tree priority 0
vlan database
vlan 11-17,20
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
gvrp enable
ip dhcp excluded-address 192.168.11.1 192.168.11.2
ip dhcp excluded-address 192.168.12.1 192.168.12.2
ip dhcp excluded-address 192.168.13.1 192.168.13.2
ip dhcp excluded-address 192.168.14.1 192.168.14.2
ip dhcp excluded-address 192.168.15.1 192.168.15.2
ip dhcp excluded-address 192.168.16.1 192.168.16.2
ip dhcp excluded-address 192.168.17.1 192.168.17.2
ip dhcp pool network CashOfficedepo
address low 192.168.12.1 high 192.168.12.254 255.255.255.0
default-router 192.168.12.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network Churn5StarPayrollWeb
address low 192.168.11.1 high 192.168.11.254 255.255.255.0
default-router 192.168.11.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network Commission
address low 192.168.13.1 high 192.168.13.254 255.255.255.0
default-router 192.168.13.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network Inventory
address low 192.168.15.1 high 192.168.15.254 255.255.255.0
default-router 192.168.15.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network Managers
address low 192.168.17.1 high 192.168.17.254 255.255.255.0
default-router 192.168.17.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network ReportingAccount
address low 192.168.14.1 high 192.168.14.254 255.255.255.0
default-router 192.168.14.1
dns-server 192.168.20.3 192.168.20.4
exit
ip dhcp pool network TechDept
address low 192.168.16.1 high 192.168.16.254 255.255.255.0
default-router 192.168.16.1
dns-server 192.168.20.3 192.168.20.4
exit
bonjour interface range vlan 1
hostname CoreSwitch
snmp-server location
snmp-server contact
clock timezone " " 0 minutes 0
ip name-server 202.XXX.XXX.XXX
ip telnet server
interface vlan 1
ip address 192.168.10.3 255.255.255.0
no ip address dhcp
interface vlan 11
name Churn5StarPayrollWeb
ip address 192.168.11.1 255.255.255.0
interface vlan 12
name CashOfficedepo
ip address 192.168.12.1 255.255.255.0
interface vlan 13
name Commission
ip address 192.168.13.1 255.255.255.0
interface vlan 14
name ReportingAccount
ip address 192.168.14.1 255.255.255.0
interface vlan 15
name Inventory
ip address 192.168.15.1 255.255.255.0
interface vlan 16
name TechDept
ip address 192.168.16.1 255.255.255.0
interface vlan 17
name Managers
ip address 192.168.17.1 255.255.255.0
interface vlan 20
name SERVERS
ip address 192.168.20.1 255.255.255.0
interface fastethernet1
switchport trunk allowed vlan add 11
interface fastethernet2
switchport trunk allowed vlan add 12
interface fastethernet3
switchport trunk allowed vlan add 13
interface fastethernet4
switchport trunk allowed vlan add 14
interface fastethernet5
switchport trunk allowed vlan add 15
interface fastethernet6
switchport trunk allowed vlan add 16
interface fastethernet7
switchport trunk allowed vlan add 17
interface fastethernet8
switchport trunk allowed vlan add 20
interface fastethernet9
shutdown
interface fastethernet10
shutdown
interface fastethernet11
shutdown
interface fastethernet12
shutdown
interface fastethernet13
shutdown
interface fastethernet14
shutdown
interface fastethernet15
shutdown
interface fastethernet16
shutdown
interface fastethernet17
shutdown
interface fastethernet18
shutdown
interface fastethernet19
shutdown
interface fastethernet20
shutdown
interface fastethernet21
shutdown
interface fastethernet22
shutdown
interface fastethernet23
shutdown
interface fastethernet24
shutdown
interface gigabitethernet1
gvrp enable
switchport trunk allowed vlan add 11-17,20
interface gigabitethernet2
switchport trunk allowed vlan add 11-17,20
interface gigabitethernet3
switchport trunk allowed vlan add 11-17,20
interface gigabitethernet4
switchport trunk allowed vlan add 11-17,20
exit
banner login ^C
Welcome to CoreSwitch.
Regards,
Sandy
^C
banner exec ^C
Welcome to CoreSwitch.
Regards,
Sandy
^C
ip default-gateway 192.168.11.2   (huwai router's fast ethernet port1 ip address)
ip default-gateway 192.168.12.2   (huwai router's fast ethernet port2 ip address)
ip default-gateway 192.168.13.2   (huwai router's fast ethernet port3 ip address)
ip default-gateway 192.168.14.2   (huwai router's fast ethernet port4 ip address)
ip default-gateway 192.168.15.2   (huwai router's fast ethernet port5 ip address)
ip default-gateway 192.168.16.2   (huwai router's fast ethernet port6 ip address)
ip default-gateway 192.168.17.2   (huwai router's fast ethernet port7 ip address)
ip default-gateway 192.168.20.2   (huwai router's fast ethernet port8 ip address)
CoreSwitch#
=====================
Switch1: no configuration yet (Tried configuring VTP but got no luck, it's not supported so i turned on the GVRP...running RSTP and spanning-tree priority is 4096)
=====================
Switch2: no configuration yet.....
Thanks,
Sandy

Please find the below mentioned show vlan output of both the Switches :
CoreSwitch#show vlan
Created by: D-Default, S-Static, G-GVRP, R-Radius Assigned VLAN
Vlan       Name                   Ports               Created by
1           1             fa1-24,gi1-4,Po1-8             D
11 Churn5StarPayroll          fa1,gi1-4                 S
     Web
12   CashOfficedepo            fa2,gi1-4                 S
13     Commission              fa3,gi1-4                 S
14 ReportingAccount           fa4,gi1-4                 S
15      Inventory              fa5,gi1-4                 S
16      TechDept               fa6,gi1-4                 S
17      Managers               fa7,gi1-4                 S
20       SERVERS               fa8,gi1-4                 S
AccessLayer1#show vlan
Vlan       Name                   Ports                Type     Authorization
1           1             fa1-24,gi1-4,Po1-8        Default      Required
AccessLayer1#
I just wondering that i have enabled GVRP on both side and made them trunk then why Switch1 is not showing me the Vlan i created on CoreSwitch :(
Thanks,
Sandy

Reg.SMTP Error while using UTL_MAIL in Oracle 10g

Hi,
I am getting the following SMTP error while trying to use the UTL.MAIL package of Oracle 10g. The query is as follows.
begin
utl_mail.send(
sender => 'NAVEEN',
recipients => '[email protected]',
subject => 'Testing utl_mail',
message => 'The receipt of this email means'|| ' that UTL_MAIL works'
end;
UTL_MAIL package is installesd and the port 25 is configured and firewall is changed.
The same block was working fine before 5 days and now is giving the error as
ORA-29279: SMTP permanent error: 501 badly formatted MAIL FROM user - no "<"
ORA-06512: at "SYS.UTL_SMTP", line 21
ORA-06512: at "SYS.UTL_SMTP", line 99
ORA-06512: at "SYS.UTL_SMTP", line 222
ORA-06512: at "SYS.UTL_MAIL", line 407
ORA-06512: at "SYS.UTL_MAIL", line 594
ORA-06512: at line 2
Could you please help me out how to proceed???
Regards,
Naveen Kumar.

Can you back that statement about an Oracle UTL_SMTP bug up with an actual bug number??
From what you have posted, this is not a bug!! but expected and documented (RFC'ed) SMTP server behaviour.
My proof:
/home/billy> telnet mail 25
Trying 165.143.128.26...
Connected to mail
Escape character is '^]'.
220 CNTRRA20-GTW01 [CNTRRA20-GTW01] Thu, 06 Mar 2008 14:26:26 +0200
HELO 10.251.93.58
250 CNTRRA20-GTW01 Hello [10.251.93.58]
MAIL FROM: naveen <[email protected]>
501 naveen <[email protected]> : illegal character(s) in domain string
MAIL FROM: NAVEEN
501 NAVEEN : domain string is NULL.
quit
221 CNTRRA20-GTW01 closing connection. Goodbye!
Connection closed by foreign host.
/home/billy>
As you can clearly see, the SMTP server expects a DOMAIN name as part of the MAIL FROM address. It also does not accept the alternative format suggested.
Yes, not all SMTP servers are equal and some support additional formatting.
But to imply that because the SMTP server does not accept your address formatted as string NAVEEN, it is a UTL_SMTP problem, sounds like a smelly one to me.

JES Messenging Server (v6.0) issues: SMTP Error: 4.0.0

Hi,
We've successfully installed Directory Server 5.2, Indentity Server 6.1, Application Server 7.0 update 1, Web Server 6.1 and Calendar Server 6.0 on a Solaris 8 system.
This system is intended for test purposes, hence all the applications are on one system. The production system will be installed on seperate systems as per Sun's recommendations.
Apropos Messenging Server (v6.0)
When I log into the the Web interface I get:
"Quota root does not exist"
If I try to send a message to a local user from the Web interface I get:
"SMTP Error: 4.0.0 temporary error returned by alias expansion: [email protected]"
I get a similar error if I try to mail a local user from outside:
220 trabant.acc.graddelt.com -- Server ESMTP (Sun ONE Messaging Server 6.0 (built Oct 29 2003))
HELO zen.sys.uea.ac.uk
250 trabant.acc.graddelt.com OK, [192.168.104.92].
MAIL From: <[email protected]>
250 2.5.0 Address Ok.
RCPT To: <[email protected]>
452 4.0.0 temporary error returned by alias expansion: [email protected]
When we installed Messenger Server, we selected Schema v2 from comm_dsetup.pl. We would like to use Messsenger Server with Identity Server.
Any suggestions as to how to overcome this issue would be most welcome.
Thanks
Shaun McCullagh
marviQ
Amsterdam

I am getting this error when I sent a mail from Sun Jav messenger express.
SMTP Error:4.0.0 temprorary error returned by alias expension:
how ever , i am able to receive the mails .
I have created one user [email protected] and configured it's account at MS outlook , this user is able to sent the mails to default account [email protected] ,Also [email protected] is obtaining the mails ,On replying to same mail i am getting SMTP error as given above.
what goes wrong ...? any idea...?
FYI...
root@ultra5c # /opt/SUNWmsgsr/sbin/./start-msg
Connecting to watcher ...
Launching watcher ...
Starting ens server ... 1461
Starting store server ...... 1462
checking store server status ........ ready
imap is running already
pop is running already
Starting http server ............................ 1463
Starting sched server ... 1473
Starting dispatcher server .............. 1475
Starting job_controller server ................ 1479
root@ultra5c # ping 192.168.0.64 110
192.168.0.64 is alive
root@ultra5c # ping 192.168.0.64 25
192.168.0.64 is alive
Rgds
chandan

Can't send email on yahoo mail, keeps switching to windows mail and smtp errors ?

When browsing using Firefox if I try and send URL or email it automatically tries to send it on Windows Mail rather then the Yahoo mail I normally use, then windows mail can't send any email out saying smtp error. Can send yahoo mail fine ?

http://support.mozilla.com/en-US/kb/Changing+the+e-mail+program+used+by+Firefox

I have suddenly got the following message An (SMTP) error occurred while sending mail. The server responded: Requested action aborted: This mail account has se

Having been on Thunderbird for some years I have suddenly got the following message when trying to send mail.
An (SMTP) error occurred while sending mail. The server responded: Requested action aborted: This mail account has sent too many messages in a short amount of time. Please try later..
I have checked the SMTP server settings in tools, account settings and they are as they have always been. Is there something I have missed?

Sending through web mail is totally irrelevant to using an SMTP server. The message even says it is from the server. Why do you think this is a Thunderbird problem.
The provider has put in place measures to keep people from spamming other email recipients using thier SMTP server. You have seen the result of those measures.

SMTP error from remote mail service

I am receiving a error that states"SMTP error from remote mail service" This is my work e-mail that is a out look e-mail service--but was put on my laptop in mozilla. If I test send e-mails to my gmail, aol and the work e-mail the work e-mail goes through (on the mozilla) but I get the error report for the gmail and aol test.

''Matt [[#answer-672468|said]]''
<blockquote>
what is the complete error message please.
</blockquote>
Hi Matt--thank you for reaching out to assist--here is the full error message I receive when I attempt to send emails--
SMTP error from remote mail server after end of data:
host p3nlsmtpcp-v01.prod.phx3.gdg [72.167.191.78]:
552 5.2.0 bT641p03m3RZ6FL01 :: CPANEL :: Message rejected for spam or virus content ::
Please include this entire message when contacting support ::
v=2.1 cv=Yecz5mhf c=1 sm=1 tr=0 p=dXr4a0FlAAAA:8 a=9P+wmFvZGoNcfX5LD2dIAQ==:117 a=9P+wmFvZGoNcfX5LD2dIAQ==:17 a=TZb1taSUAAAA:8 a=xSRs65CQCjkA:10 a=IkcTkHD0fZMA:10 a=o1OHuDzbAAAA:8 a=YNv0rlydsVwA:10 a=AK46IGkTethYI5b8t1AA:9 a=QEXdDO2ut3YA:10 a=RBqHpAr1aNgA:10 a=SZlYXZE0WA8A:10 a=POQKUN4lQn8A:10 a=5LQJebhDX5EA:10 a=lWHhIcKi20EA:10 a=AP_QpuyW5RgA:10 a=_ZmE1jEfA50A:10 a=fVc70mvjwYYA:10 a=BfRt8DTvoOQA:10 ::
100.00

Smtp error

Dear all,
Running Iplanet Messaging server 5.2 P1.While sending a message in webmail when i click on send i get the message smtp error.After going through the logs i found the following entries
tcp_local Q 9 rfc822;min@kathatraveline
s.com [email protected] TCP active open: Failed connect() Error: Connec
tion timed out
22-Jul-2005 21:31:25.00 tcp_local Q 10 rfc822;Dwight@zarifitnes
s.com [email protected] TCP active open: Failed connect() Error: Connect
ion timed out
I have checked that the functionality of the dns and it is working fine.there is no issue with our network also..Can anyone throw some light on this.
Thanks in advance

If you get an error in webmail every time you click "send", that means that either:
1. your service.http.smtphost or service.http.smtpport is incorrect. These default to your local store system, but if they've been changed to point to some other box, that box isn't responding
or
2. Your store box isn't correctly configured to accept mail from "localhost".
The message you find from the MTA is totally unrelated. That message is telling you that when Messaging Server attempted to send to the address outside your network, that connection wasn't made, the remote server timed out.
The remote server could be down, or simply not running a mail server at the time the message attempt was made. "Q" means, we reQueue the message, and try again, later,using the "backoff" settings.

Getting server error. CrystalEnterprise.Smtp: error when scheduled a webi

Getting server error. CrystalEnterprise.Smtp: error when scheduled a webi report to save as excel and send to an email account. What things to look for?

yes you should read the administration documents,
go to CMC, find "servers"
then "destination job server"
then click the "destination " tab
you will find some parameters, you have to configure it you.
the same scenario will be done to the "web intelligence job server"
good luck
Amr

Mailer object error message "SMTP: invalid from address. SMTP error 530 5.7.0 Must issue a STARTTLS command first. d5sm35857280yhl.19".

I am trying to send an email from Lookout V6.6 using the Mailer object. I have an email address setup through GMAIL and have verified it works. Also, Lookout Mailer object is able to verify GMAIL server. I get the following error message when trying to send the email: "SMTP: invalid from address. SMTP error 530 5.7.0 Must issue a STARTTLS command first. d5sm35857280yhl.19". Anyone know what is causing this?

Another method is to use a SMTP relayer, we have deployed them in the past.
http://www.hmailserver.com/index.php?page=welcome
Mike
Forshock - Consult.Develop.Solve.

SMTP Error 5.7.1 Unable to relay - from webmail interface

Hi,
This is some strange problem i faced for the first time.
Below Messaging Version on Solaris 10 which is working fine.
Sun Java(tm) System Messaging Server 6.2-7.05 (built Sep 5 2006)
libimta.so 6.2-7.05 (built 12:18:44, Sep 5 2006)
Sometimes (very rarely), users getting "relaying problem" even they try to send from webmail (using browser) interface.
Part of log written to "http" file under <msg-hime>/log directory:
[24/Jun/2007:15:42:34 -0400] webmail httpd[23377]: General Warning: saveSmtp failed: SMTP Error 5.7.1 Unable to relay for [email protected]
Any help highly appreciated
TIA
Prvn

Hi shane,
All incoming mails (incl. sent self mails using webmail interface) seem to be looped. Not able to receive any mail.
The logs written in mail.log_current below: (when sent self mails using webmail)
when service.http.smtphost = 127.0.0.1 :
26-Jun-2007 05:36:32.09 tcp_intranet tcp_scan E 2 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:36:32.19 tcp_scan D 2 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|43340|192.168.1.49|10026) (mailgw Symantec Mail Security Tue, 26 Jun 2007 05:36:22 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:36:36.10 tcp_intranet tcp_scan E 3 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:36:36.20 tcp_scan D 3 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|43411|192.168.1.49|10026) (mailgw Symantec Mail Security Tue, 26 Jun 2007 05:36:26 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:36:40.09 tcp_intranet tcp_scan E 3 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:36:40.19 tcp_scan D 3 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|43414|192.168.1.49|10026) (mailgw Symantec Mail Security Tue, 26 Jun 2007 05:36:30 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:36:44.13 tcp_intranet tcp_scan E 4 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
when service.http.smtphost = 192.168.1.41:
26-Jun-2007 05:20:45.93 tcp_intranet tcp_scan E 5 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:20:46.00 tcp_scan D 5 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|36905|192.168.1.49|10026) (mailgw
Symantec Mail Security Tue, 26 Jun 2007 05:20:36 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:20:46.17 tcp_intranet tcp_scan E 9 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:20:46.27 tcp_scan D 9 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|36906|192.168.1.49|10026)
(mailgw Symantec Mail Security Tue, 26 Jun 2007 05:20:36 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:20:46.32 tcp_intranet tcp_scan E 5 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:20:46.40 tcp_scan D 5 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|36907|192.168.1.49|10026) (mailgw
Symantec Mail Security Tue, 26 Jun 2007 05:20:37 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:20:46.58 tcp_intranet tcp_scan E 10 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:20:46.67 tcp_scan D 10 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|36908|192.168.1.49|10026)
(mailgw Symantec Mail Security Tue, 26 Jun 2007 05:20:37 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:20:46.72 tcp_intranet tcp_scan E 6 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
26-Jun-2007 05:20:46.79 tcp_scan D 6 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] [192.168.1.49] dns;[192.168.1.49] (TCP|192.168.1.41|36909|192.168.1.49|10026) (mailgw
Symantec Mail Security Tue, 26 Jun 2007 05:20:37 -0700 ) smtp;250 2.1.5 [email protected]
26-Jun-2007 05:20:46.97 tcp_intranet tcp_scan E 10 [email protected] rfc822;[email protected]
@tcp_scan-daemon:[email protected] mailgw ([192.168.1.49])
Regards,
Prvn

SMTP Error Code : 530 . For more information, see your SMTP server manual.

Hello,
I am Getting
"SMTP Error Code : <530>. For more information, see your SMTP server manual" error, While configuring SMTP in Data Services 4.0 system. I have tried executing the SMTP_TO function on another DS machine which has 3.2 verion installed, but getting the same error.
FYI,
1) Able to telnet the Exchange server through Data service machine
2) Maintained SMTP settings in Data services server manager
3) using the same SMTP server host name in other SAP systems (ECC,BI,PI) etc and able to send mails.
Regards
Puneet

Thanks for the reply Julian.
There was a problem in SMTP relay rights on Exchange server. Able to send mails now. Thanks!
Getting another problem wherein I am not able to send mails to multiple recipients i.e. If I specify 5 recipients in SMTP_TO function and execute the job then Every individual is getting E-Mail having there own ID in TO field, other Id's are not gettting displayed in TO field.
I hve checked note "1276348 - smtp_to function - multiple recipients not displayed"
Settings mentioned in the note have been done and job is getting executed without any error but the mails are not getting delivered.
It would be great if anyone can suggest on how to proceed here.
Thanks & Regards
Puneet

SMTP error from remote mail server after initial connection:

Hello folks. I having some serious issues sending email to clients with .mac accounts. I keep on getting the following error. Can someone help? I have replaced email address names with "Blank@...) for obvious reasons.
This message was created automatically by mail delivery software.
A message that you sent could not be delivered to one or more of its
recipients. This is a permanent error. The following address(es) failed:
[email protected]
SMTP error from remote mail server after initial connection:
host smtp-mx1.mac.com [17.148.20.64]: 452 try later:
retry timeout exceeded
------ This is a copy of the message, including all the headers. ------
Return-path: <[email protected]>
Received: from ip72-207-229-240.br.br.cox.net ([72.207.229.240] helo=[192.168.0.102])
by srv3.purenrg.com with esmtp (Exim 4.68)
(envelope-from <[email protected]>)
id 1JFeOb-0001FZ-5F
for [email protected]; Thu, 17 Jan 2008 18:43:41 -0500
Message-Id: <[email protected]>
From: "[email protected]" <[email protected]>
To: Cindy Barnes <[email protected]>
Content-Type: multipart/alternative; boundary=Apple-Mail-3--1032078955
Mime-Version: 1.0 (Apple Message framework v915)
Subject: invoice 520 is overdue
Date: Thu, 17 Jan 2008 17:43:40 -0600
X-Mailer: Apple Mail (2.915)
X-PopBeforeSMTPSenders: [email protected]{
--Apple-Mail-3--1032078955
Content-Type: text/plain;
charset=US-ASCII;
format=flowed
Content-Transfer-Encoding: 7bit

I'm sure someone will give more detail, but it looks like the server blocked your address because it thinks it's a spam source. If you're not spamming, then it might be someone on the same network spamming, or malware on your computer doing it. Or it could just be a mistake. try calling whoever runs your mail server and see if they can give you more information.

SMTP Error: 5.3.4 & aliasdetourhost

Hi.
Version of SJMS:
Sun Java(tm) System Messaging Server 6.3-4.01 (built Aug 3 2007; 32bit)
libimta.so 6.3-4.01 (built 17:13:29, Aug 3 2007; 32bit)
SunOS mess1 5.10 Generic_125100-10 sun4u sparc SUNW,Sun-Fire-V440
My problem:
I have configured email checking via 'aliasdetourhost' keyword and message size limit via COS in LDAP. When I try to send an email with attachment I get the error "SMTP Error: 5.3.4 a message size of 302 kilobytes exceeds the size limit of 300 kilobytes computed for this transaction".
! tcp_scanner
tcp_scanner smtp mx single_sys subdirs 20 noreverse maxjobs 7 \
pool SMTP_POOL daemon imss.army.cz enqueue_removeroute
tcp_scanner-daemon
! tcp_noscan
tcp_noscan smtp mx single_sys subdirs 20 dequeue_removeroute maxjobs 7 pool SMTP_POOL maytlsserver allowswitchchannel saslswitchchannel tcp_auth missingrecipientpolicy 4
tcp_noscan-daemon
! nastaveni pro ALIASDETOURHOST
! tcp_local
tcp_local smtp mx daemon imss.army.cz single_sys remotehost inner switchchannel identnonenumeric subdirs 20 maxjobs 7 \
pool SMTP_POOL maytlsserver maysaslserver saslswitchchannel tcp_auth missingrecipientpolicy 0 aliasdetourhost tcp_scanner-daemon
tcp-daemon
!tcp_intranet
tcp_intranet smtp mx single_sys remotehost inner switchchannel identnonenumeric subdirs 20 maxjobs 7 pool SMTP_POOL maytlsserver maysaslserver saslswitchchannel tcp_auth missingrecipientpolicy 0 aliasdetourhost tcp_scanner-daemon
tcp_intranet-daemon
I found in forums that someone had the same problem and "solved" it with LDAP_BLOCKLIMIT keyword in option.dat. It is helpful, but after I set this up the MTA ignores my limits and users can send emails with unlimited size of attachments (except webmail where is limit with 'service.http.maxmessagesize' keyword.)
I tried to set up global message size limit with 'BLOCK_LIMIT' option as well as the sourceblocklimit keyword in imta.cnf and it didn't help and I got the same error message...
Does anybody know where should be the problem?

Hi,
berrosch76 wrote:
I have configured email checking via 'aliasdetourhost' keyword and message size limit via COS in LDAP.What is the size-limit you have set (the exact CoS attribute and value)?
When I try to send an email with attachment I get the error "SMTP Error: 5.3.4 a message size of 302 kilobytes exceeds the size limit of 300 kilobytes computed for this transaction".Who exactly are you trying to send the email to (an internal user/group or external address)?
Do you get this error if you attempt to send to an external address (e.g. [email protected])?
I found in forums that someone had the same problem and "solved" it with LDAP_BLOCKLIMIT keyword in option.dat.I'm not quite sure how this is going to help unless you 'break' the existing default which is LDAP_BLOCKLIMIT=mailMsgMaxBlocks
Where customers get confused is when they provision using Delegated Administrator and give a user a 'silver' profile for example.
This profile has the somewhat limited restriction of "mailMsgMaxBlocks: 300" as per http://docs.sun.com/app/docs/doc/819-4438/6n6jdjbda?a=view. This 300 translates to 300KB which gives the error you mention. Rather then fixing/changing the CoS profile they 'break' the restriction mechanism by changing LDAP_BLOCKLIMIT.
It is helpful, but after I set this up the MTA ignores my limits and users can send emails with unlimited size of attachments (except webmail where is limit with 'service.http.maxmessagesize' keyword.)That is to be expected. All changing LDAP_BLOCKLIMIT will do is to disable per-user size restrictions. This doesn't address the source of the problem.
I tried to set up global message size limit with 'BLOCK_LIMIT' option as well as the sourceblocklimit keyword in imta.cnf and it didn't help and I got the same error message...The smaller per-user limit will override the larger global limit.
Does anybody know where should be the problem?You need to look at what you have set for the user re: CoS profile.
Regards,
Shane.

Smtp error in a cisco SF300

Similar Messages

Maybe you are looking for