Smtp failed connection attemp

Hi
This is my scenario
Exchange 2010 --> TMG 2010--> UBM Xroads --> ISP
My TMG runs on Hyper-V and Windows 2008 R2 hosted for Windows server 2012 R2
two NICS
When i publish the Exchange server on TMG receive without problems but send email is not working
Failed Connection Attempt PMSNTMGSVRV 25/02/2014 10:01:38 a.m.
Log type: Firewall service
Status: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.
Rule: mailOUT
Source: Internal (192.168.1.20:7419)
Destination: External (85.158.140.211:587)
Protocol: mail
Additional information
Number of bytes sent: 0 Number of bytes received: 0
Processing time: 21015ms Original Client IP: 192.168.1.20
I´m already chek NIC config and all seems to be ok. but i´m stuck with this.
Any idea?

Hi, check if the destination Server is listening on port 587. SMTP traffc normally uses TCP port 25
regards Marc Grote aka Jens Baier - www.it-training-grote.de - www.forefront-tmg.de - www.galileocomputing.de/3570

Similar Messages

TCP active open: Failed connect() Error: Connection timed out SMTP

Hi,
Messaging server version is,
./imsimta version
Sun Java(tm) System Messaging Server 6.2-6.01 (built Apr 3 2006)
libimta.so 6.2-6.01 (built 11:20:35, Apr 3 2006)
SunOS bglbbmr1-a-fixed 5.9 Generic_118558-28 sun4u sparc SUNW,Sun-Fire-V440
17-Dec-2008 10:47:40.08 1730.8e.741
tcp_local Q 4 [email protected] rfc822;[email protected] [email protected] /mta/queue/queue/tcp_local/013/ZUg0i1t9I0ZG~.00 <[email protected]>; TCP active open: Failed connect() Error: Connection timed out SMTP/xyz.my-domain.in
I have been getting this above error on my mail server from last
4-5 days. I am getting complaints from end users that the users can't
send any mails using Outlook but I did check with my test user I can
send mail by using webmail.
The Failed MX lookup Errors also getting in my logs the error detail given bellow.
17-Dec-2008 10:47:39.65 1730.91.737
tcp_local - Y TCP|0.0.0.0||209.85.143.114|25 SMTP/airtelmail.in/aspmx.l.google.com
17-Dec-2008 10:47:39.92 1754.41.255
tcp_notify - Y SMTP/infomedia18.in/infomedia18.in
17-Dec-2008 10:47:39.92 1754.41.256
tcp_notify Q 7 rfc822;[email protected] [email protected] /mta/queue/queue/tcp_notify/017/ZXg0i1t3U_ZoD.00 <[email protected]>; Failed MX lookup; try again later
17-Dec-2008 10:47:39.94 1754.41.257
tcp_notify Q 6 rfc822;[email protected] [email protected] /mta/queue/queue/tcp_notify/010/ZXg0i1t3U_ZoF.00 <0KBZ003MRGU7MQ30@my-domain> Failed MX lookup; try again later
I tried stopping and starting msg service using stop-msg and start-msg to sort out this above problem but no result. :(
When I do check the tcp_local queue it has been growing every day as well the tcp_notification queue also.
/opt/SUNWmsgsr/sbin/imsimta qm su
Messages
Channel Queued Size (Kb) Oldest
tcp_notify 10741 1080610.61 16 Dec, 00:59:24
tcp_local 8334 733849.31 15 Dec, 00:19:00
tcp_lmtpcn 0 0.00
tcp_be 0 0.00
reprocess 0 0.00
process 0 0.00
conversion 0 0.00
Totals 19075 1814459.92
This queues are increasing day by day.
One more thing is that I cant see a service/channel called CONVERSION running on my server when i do use this command.
ps -aef | grep conversion
root 6144 6000 0 11:14:28 pts/1 0:00 grep conversion
When i try to start it using imsimta qm utility, output shows as
qm.maint>; start conversion
QM-I-STARTED, channel was not stopped
qm.maint>;
Later I stopped and started conversion channel
qm.maint>; stop conversion
QM-I-STOPPED, channel stopped
qm.maint>; start conversion
QM-I-STARTED, channel started
qm.maint>;
I can see that on other servers the conversion channel is running and few msges are in queue. I do have other servers which running the same messaging server. But I am not getting why don't on this server. Where both servers having the same configuration.
Please, help me to sort out this issue.
Thanks in advance....
BSK

Thanks Mr. Shane,
The server which is running conversion channel.
ps -eaf|grep conversion
mailserv 16824 8472 3 17:08:11 ? 0:48 /opt/SUNWmsgsr/lib/conversion
mailserv 28728 8472 0 17:17:30 ? 0:00 /opt/SUNWmsgsr/lib/conversion
root 1057 26387 0 17:18:12 pts/1 0:00 grep conversion
more /opt/SUNWmsgsr/config/conversions
in-channel=*; in-type=application; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=x-zip-compressed; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=image; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=audio; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=video; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
Following entry from /opt/SUNWmsgsr/lib/config-templates/imta_tailor
IMTA_CONVERSION_FILE=<msg.RootPathUNIX>/config/conversions
The server which doesnt show running conversion channel
#more /opt/SUNWmsgsr/config/conversions
!in-channel=*; in-type=*; in-subtype=*; in-disposition=*;
! parameter-symbol-0=NAME; parameter-copy-0=*;
! dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
! message-header-file=2; original-header-file=1;
! override-header-file=1; override-option-file=1;
! command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=application; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=x-zip-compressed; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=image; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=audio; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
in-channel=*; in-type=video; in-subtype=*; in-disposition=*;
parameter-symbol-0=NAME; parameter-copy-0=*;
dparameter-symbol-0=FILENAME; dparameter-copy-0=*;
message-header-file=2; original-header-file=1;
override-header-file=1; override-option-file=1;
command="/opt/SUNWmsgsr/private/virusscan.sh"
Following entry from /opt/SUNWmsgsr/lib/config-templates/imta_tailor
IMTA_CONVERSION_FILE=<msg.RootPathUNIX>/config/conversions
Is this above information u r asking?
As u wrote erlier, the conversion channel works some times and some times doesn't work.
Thanks lot...
BSKADAM

SpamAssassin / Amavisd tuning - TCP active open: Failed connect() errors

I started this post as we were experiencing a problem with occassional delayed mail delivery to our mail store. As I continued writing it, I think that I've resolved it. But I wanted to post this anyway so if I'm doing things right it might help someone else; or, if I'm doing something wrong someone can correct me. :) For reference, we have a quad Sun v440, and process about 500,000 messages a day.
We were seeing messages like this in our log files:
09-Nov-2006 08:28:09.37 tcp_scan Q 1 [email protected] rfc822;[email protected] @tcp_scan-daemon:[email protected] TCP active open: Failed connect() Error: Connection timed out
example.com represents our local domain. The errors seemed to occur proportionally to the amount of incoming mail we received. That is, we saw more of them under load.
We are running SpamAssassin, Amavisd/clamav, and:
Sun Java(tm) System Messaging Server 6.2-5.01 (built Nov 22 2005)
libimta.so 6.2-5.01 (built 11:57:57, Nov 22 2005)
SunOS hostname 5.9 Generic_118558-11 sun4u sparc SUNW,Sun-Fire-V440
This line seems to say that the message is in the tcp_scan channel, and cannot send to 127.0.0.1:10024 (amavisd) because that port isn't listening.
My amavisd max_servers was set at 15. After reading http://www.ijs.si/software/amavisd/amavisd-new-magdeburg-20050519.pdf and making a wild guess, I increased it to 30. The errors were less frequent, but still occurred.
The output of 'sar -d' showed that my local disk was experiencing upwards of 80% utilization. I moved the amavisd temp directory and the spamassassin bayes db to a san volume, and that sped everything up dramatically. The connect errors went away, clamav avg time per message is at 4 seconds down from 10. I am now receiving errors from spamassassin that say:
Nov 9 10:27:27 hostname.example.com spamd[21601]: prefork: server reached --max-children setting, consider raising it
My --max-children is set to 25 right now, and the server is cpu bound under heavy load, so I see no reason to raise it.
So this is my setup. I am no longer having an immediate problem, but comments/questions are welcome.
Config files related to my setup are below.
Excerpts of imta.cnf:
! tcp_scan
[] $E$R${tcp_scan,$L}$U%[$L]@tcp_scan-daemon
! ims-ms
ims-ms defragment subdirs 20 notices 1 7 14 21 28 backoff "pt5m" "pt10m" "pt30m" "pt1h" "pt2h" "pt4h" maxjobs 2 pool IMS_POOL destinat
ionspamfilter1 fileinto $U+$S@$D
ims-ms-daemon
! tcp_local
tcp_local smtp mx single_sys remotehost inner switchchannel identnonenumeric subdirs 20 maxjobs 7 pool SMTP_POOL saslswitchchannel tcp
auth maytlsserver maysaslserver missingrecipientpolicy 0 aliasdetourhost tcpscan-daemon
tcp-daemon
! tcp_intranet
tcp_intranet smtp mx single_sys subdirs 20 dequeue_removeroute maxjobs 7 pool SMTP_POOL allowswitchchannel saslswitchchannel tcp_auth
maytlsserver maysaslserver missingrecipientpolicy 4 aliasdetourhost tcp_scan-daemon
tcp_intranet-daemon
! tcp_scan
tcp_scan smtp single_sys subdirs 5 notices 1 backoff "pt10m" "pt30m" "pt2h" "pt4h" dequeue_removeroute maxjobs 7 pool SMTP_POOL daemon
[127.0.0.1] port 10024
tcp_scan-daemon
option.dat:
SPAMFILTER1_LIBRARY=/opt/sunjes/SUNWmsgsr/lib/libspamass.so
SPAMFILTER1_CONFIG_FILE=/opt/sunjes/SUNWmsgsr/config/SpamAssassin
SPAMFILTER1_STRING_ACTION=data:,require ["addheader"]; addheader "Spam-test: $U"; require "fileinto"; fileinto "Junk";
SPAMFILTER1_OPTIONAL=1
dispatcher.cnf:
[SERVICE=SMTP-SCAN]
DEBUG=-1
PARAMETER=CHANNEL=tcp_scan
PORT=10025
IMAGE=IMTA_BIN:tcp_smtp_server
LOGFILE=IMTA_LOG:tcp_scan-server.log
STACKSIZE=2048000
INTERFACE_ADDRESS=127.0.0.1
SpamAssassin:
host=127.0.0.1
port=783
debug=0
mode=1
field=
verdict=Junk
USE_CHECK=0

Suggest dropping Amavis in preference to the built-in
integration, per our documentation. Simpler, more
performant.Sorry, my title wasn't very accurate. We are running SpamAssassin through the built in integration, and clamav through amavisd. There isn't any built in integration to clamav, is there?

SMTP fails to recognize email address

Hi there,
i'm having a tough and irritating problem: when i create Transport from the Session in tomcat's (v 5.5) context, i get the following Exception:
SMTPAddressFailedException: 550 5.1.1 Bad destination mailbox address ([email protected])
i went google but with no success as well as nothing in java forums..
Interesting thing is that on my localhost it works fine, but when uploaded to remote server it fails (context.xml has the same settings). Here is my code:
Context initCtx = new InitialContext();
               Context envCtx = (Context) initCtx.lookup("java:comp/env");
               Session session = (Session) envCtx.lookup("mail/Session");
               System.out.println(session.getProperty("mail.smtp.auth"));
               Message message = new SMTPMessage(session);
               message.setFrom(new InternetAddress(from));
               message.addRecipient(javax.mail.Message.RecipientType.TO, new InternetAddress(to.trim()));
               message.setSubject(subject);
               message.setContent(text, "text/plain;charset=windows-1257");
               Transport service = session.getTransport("smtp");
               service.connect();
               message.saveChanges();
               service.sendMessage(message, message.getRecipients(Message.RecipientType.TO));
               service.close();
.. and context.xml for application:
<?xml version="1.0" encoding="UTF-8"?>
<Context
reloadable="true"
workDir="......">
<Resource
name="mail/Session"
type="javax.mail.Session"
mail.smtp.host="mail.takas.lt" mail.debug="true"/>
</Context>
Any help, please?? Would appreciate it alot.
Ramunas

i guess that is not a problem, because the deny comes from the smtp server for recipient address which is correct, eventhough the sender (From) email is incorrect and mail server accepts it. Here's some debug output, maybe it could help?
MAIL FROM:<[email protected]>
250 2.1.0 [email protected]...Sender OK
RCPT TO:<[email protected]>
550 5.1.1 Bad destination mailbox address ([email protected]).
DEBUG SMTP: Invalid Addresses
DEBUG SMTP: [email protected]
DEBUG SMTP: Sending failed because of invalid destination addresses
RSET
250 2.0.0 Resetting
javax.mail.SendFailedException: Invalid Addresses;
nested exception is:
class com.sun.mail.smtp.SMTPAddressFailedException: 550 5.1.1 Bad destination mailbox address
the code 550 is response from smtp host, not the remote pc..

Javax.xml.soap.SOAPException: Message send failed: Connection timed out

Hi,
where can i adjust the timeout for:
exception on JaxRpc invoke: HTTP transport error: javax.xml.soap.SOAPException: java.security.PrivilegedActionException: javax.xml.soap.SOAPException: Message send failed: Connection timed out: connect
The webservice needs 5min to return a message....
I found a duplicate of this on thread:
error initiating a test instance
But no answer
Message was edited by:
HEWizard

I found http://download-uk.oracle.com/docs/cd/B31017_01/integrate.1013/b28981/events.htm#BABGGADB
Setting Timeouts for Synchronous Processes
For synchronous processes that connect to a remote database, you must increase the syncMaxWaitTime timeout property in the SOA_Oracle_Home\bpel\domains\default\config\domain.xml file:
<property id="syncMaxWaitTime">
<name>Delivery result receiver maximum wait time</name>
<value>60000000</value>
<comment>
<![CDATA[The maximum time the process result receiver will wait for a
result before returning. Results from asynchronous BPEL processes are
retrieved synchronously via a receiver that will wait for a result from the
container.
<p/>
The default value is 60 seconds.]]>
</comment>
</property>
But this changes nothing...
Is this value ignored?

TAC+: TCP/IP open to 10.20.17.2/49 failed -- Connection timed out; remote host not responding

TACACS+ configured on router and router is in ACS. I can ping the ACS but the router cannot establish a connection to authenticate users.
aaa group server tacacs+ hq_acs-1
server 10.20.17.2
ip tacacs source-interface GigabitEthernet0/0
aaa authentication login default group tacacs+ local
aaa authorization config-commands
aaa authorization exec default group tacacs+ local
aaa authorization commands 10 default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa accounting nested
aaa accounting update newinfo periodic 60
aaa accounting auth-proxy default start-stop group tacacs+
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
aaa accounting resource default start-stop group tacacs+
BigTree_3945#sh ip int br
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0         10.4.3.1        YES NVRAM down                  down
GigabitEthernet0/1         10.12.10.26     YES NVRAM up                    up
Serial0/2/0                unassigned      YES NVRAM down                  down
Serial0/2/0.602            10.12.15.10     YES NVRAM down                  down
Apr 13 11:08:13.673: TPLUS: Queuing AAA Authentication request 79 for processing
Apr 13 11:08:13.673: TPLUS: processing authentication start request id 79
Apr 13 11:08:13.675: TPLUS: Authentication start packet created for 79(cisscdb)
Apr 13 11:08:13.675: TPLUS: Using server 10.20.17.2
Apr 13 11:08:13.675: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
Apr 13 11:08:18.676: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
Apr 13 11:08:18.676: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
Apr 13 11:08:18.676: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
Apr 13 11:08:25.834: TPLUS: Queuing AAA Authentication request 79 for processing
Apr 13 11:08:25.834: TPLUS: processing authentication start request id 79
Apr 13 11:08:25.834: TPLUS: Authentication start packet created for 79(cisscdb)
Apr 13 11:08:25.834: TPLUS: Using server 10.20.17.2
Apr 13 11:08:25.834: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
Apr 13 11:08:30.836: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
Apr 13 11:08:30.836: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
Apr 13 11:08:30.836: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
Apr 13 11:08:43.689: TAC: Using default tacacs server-group "tacacs" list.
Apr 13 11:08:43.689: TAC+: Opening TCP/IP to 10.20.17.2/49 timeout=5
Apr 13 11:08:51.057: TPLUS: Queuing AAA Authentication request 79 for processing
Apr 13 11:08:51.057: TPLUS: processing authentication start request id 79
Apr 13 11:08:51.057: TPLUS: Authentication start packet created for 79(cisscdb)
Apr 13 11:08:51.057: TPLUS: Using server 10.20.17.2
Apr 13 11:08:51.057: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
Apr 13 11:08:54.692: TAC+: TCP/IP open to 10.20.17.2/49 failed -- Connection timed out; remote host not responding
Apr 13 11:08:54.692: TPLUS: Queuing AAA Accounting request 76 for processing
Apr 13 11:08:54.692: TPLUS: processing accounting request id 76
Apr 13 11:08:54.692: TPLUS: Sending AV task_id=332
Apr 13 11:08:54.692: TPLUS: Sending AV timezone=EDT
Apr 13 11:08:54.692: TPLUS: Sending AV service=shell
Apr 13 11:08:54.692: TPLUS: Sending AV start_time=1334329734
Apr 13 11:08:54.692: TPLUS: Sending AV priv-lvl=15
Apr 13 11:08:54.692: TPLUS: Sending AV cmd=show logging <cr>
Apr 13 11:08:54.692: TPLUS: Accounting request created for 76(n20j03t)
Apr 13 11:08:54.692: TPLUS: Using server 10.20.17.2
Apr 13 11:08:54.692: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: Started 5 sec timeout
Apr 13 11:08:56.058: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
Apr 13 11:08:56.058: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
Apr 13 11:08:56.058: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
Apr 13 11:08:59.693: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: timed out
Apr 13 11:08:59.693: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: timed out, clean up
Apr 13 11:08:59.693: TPLUS(0000004C)/1/20FD90EC: Processing the reply packet
BigTree_3945#
AAA Client IP Address
10.4.3.* 10.12.15.10
Key
Network Device Group
Test
NJT
AccessLink
(Not Assigned)
Authenticate Using
TACACS+ (Cisco IOS)
RADIUS (Cisco Aironet)
RADIUS (Cisco BBSM)
RADIUS (Cisco IOS/PIX)
RADIUS (Cisco VPN 3000)
RADIUS (Cisco VPN 5000)
RADIUS (IETF)
RADIUS (Ascend)
RADIUS (Juniper)
RADIUS (Nortel)
RADIUS (iPass)
Single Connect TACACS+ AAA Client (Record stop in accounting on failure).
The 10.12.10.* range is listed under the HQ site.
Your help is greatly appreciated.

You stated that you can ping ACS from the router, did you try sourcing the packets from the GigabitEthernet 0/0 interface (which is the one TACACS+ will try to use, given the configuration that you posted)?
What does the network path between the router and ACS look like (ie, any firewalls, NAT, etc)?
Can you connect to port 49 at the ACS IP address from the router sourcing the packets from GigabitEthernet 0/0 ?
Are you using VRFs?
What version of IOS?

TCP active open: Failed connect()

hi all,
i receive error from my email like
"TCP active open: Failed connect()x.x.x.x :25(No formatted text for errno = 111)"

Hi Mustapah,
if the error is in the email, then the hostname and/or IP address of the reporting server/appliance should be in there.
I suggest you try to look up the message in message tracking of your IronPort's GUI, this will tell you if the message was received by your appliance(s), and also if it was bounced on the appliance or on a different server.
Hope that helps,
Andreas

TCP active open: Failed connect() Error: Connection timed out

Hi,
There is one message which can't be delieved to the recepient with error " TCP active open: Failed connect() Error: Connection timed out" This is the error that we found in the mail.log_current file.
I have no problem sending email to the same address from my hotmail account.
any suggestion ?
Thanks,
Joe

The message can only mean one thing. Your server cannot connect to that host.
It's possible that the remote system is lying to your Messaging Server, and that's gotten it confused. Some firewalls do this by repeating the entire capability string from the server behind them, but can't actually handle all the capabilities.
PIX firewalls do this.
When you connect, they pretend to be able to "startls", but if you try, they hang up. They appear to handle "EHLO", but when you try, they hang up.
You can put debugging on the tcp_local channel, and see the actual conversation, if you like.
master_debug and slave_debug go into the imta.cnf definition line. MM_DEBUG=5 goes at the end of your option.dat file.
then
imsimta cnbuild
imsimta restart
will attempt to send the message. You will want to back the changes out, as you'll get lots of extra log files you really don't need.
Post the log file, and we can see what's happening.

RFC logon failed with message: Failed: Connect to SAP gateway failed

I installed CI instance fine and i am stopped here with this error at the end of DB instance install. Could someone let me know what could be the reason for this. Is there any fix or workaround to continue the install.
INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
          CAbRfcImpl::setRfcConnectParam
RFC parameter ASHOST set to value hostSAP.
INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
          CAbRfcImpl::setRfcConnectParam
RFC parameter SYSNR set to value 09.
INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:543]
          CAbRfcImpl::checkConnectInfo
RFC connection information checked successfully.
ERROR      2006-09-16 01:13:02 [iaxxrfcimp.cpp:450]
          CAbRfcImpl::openRfcConn
FRF-00007 Unable to open RFC connection.
ERROR      2006-09-16 01:13:02
          CJSlibModule::writeError_impl()
FRF-00063 RFC logon failed with message: Failed: Connect to SAP gateway failed
Connect_PM GWHOST=hostSAP, GWSERV=sapgw09, ASHOST=hostSAP, SYSNR=09
LOCATION    CPIC (TCP/IP) on local host
ERROR       partner not reached (host hostSAP, service 3309)
TIME        Sat Sep 16 01:13:02 2006
RELEASE     640
COMPONENT   NI (network interface)
VERSION     37
RC          -10
MODULE      nixxi_r_mt.cpp
LINE        8528
DETAIL      NiPConnect
SYSTEM CALL connect
ERRNO       146
ERRNO TEXT Connection refused
COUNTER     4
Thanks,
Ram

at the end of the database instance installation SAPInst is doing some RFCs to the CI.
The logfile states that the gateway on host hostSAP with the systemnumber 09 is not reachable.
Please check if you have started the central instance on this machine.
peter

Pulseaudio problem , snd_pcm_open failed: Connection refused.

Hello everyone, i have this problem that appeared last week.
I cant play music in any player cause i get this error : snd_pcm_open failed: Connection refused.
i tried things like adding the user to audio group, creating a "pulse" user cause pulseaudio gave me an error like "pulse user" not existent .
but if i test the sound card in the kde4 audio setup it works
anyone have any ideea on how to fix this ?

just restart alsa.
sudo /etc/rc.d/alsa restart
it solved my problem.

SOAPException: Message send failed: Connection timed out

Hi! How to solve "javax.xml.soap.SOAPException: Message send failed: Connection timed out: connect" in a page jspx using ADF Webservices Data Controls ? I'm using JDeveloper 11.1.1.2 .
Edited by: reginaldo oliveira on 16/09/2010 11:29

Vishal, I'm taking up this question. I can't to use HTTP Analyser because one of the parameters of my web service is a datasource of weblogic domain, and I know that an error occurs when I have an application in weblogic domain of JDeveloper 11.1.1.2 trying obtain connection pool from other weblogic domain. In fact, I need a way to set proxy and port if I use web service through a web service proxy and/or web service data control of ADF. Using web service proxy, in my class PortClient I have defined a method this way:
    public static void definirProxy(){
        String enderecoProxy = null;
        String porta = null;
        try{
            enderecoProxy = "190.0.1.236";
            porta = "80";
            System.setProperty("http.proxyHost", enderecoProxy);
            System.setProperty("http.proxyPort", porta);
            System.setProperty("http.nonProxyHosts", "localhost, 127.0.0.1");
        }catch( MissingResourceException mre ){
            mre.printStackTrace();
    }this don't work, but I do it because I have read this page:
http://download.oracle.com/javase/1.5.0/docs/guide/net/proxies.html
Do you have an idea? And how to set proxy and port when we using ADF Data Controls of web services?

Management console fails connecting to Management server.

I have installed Oracle 9.2 on Red Hat Advanced Server V2.1.
Also installed Management server and client software on the system.
Started everything up: oemctl start oms, agentctl start agent, apachectl start...
Run Manager Console on Linux machine (i.e. locally)
Runs successfully - connecting stand-alone
Runs successfully - connecting to management sever
Installed client software on a Windows NT PC.
Runs successfully - connecting stand-alone
FAILS - connecting to Management server
On another NT PC, try running web interface to Management server
FAILS - Same error as when using thick client.
Failure is the same in both cases: The exception (java.lang.NullPointerException) occured.
Failure of both of these suggested a server issue...
Don't know where to find management server logs?
Looking at $ORACLE_HOME/Apache/Apache/logs/error_log seems unable to find files, e.g.:
[Mon Nov 25 10:01:46 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/readme/emreadme.htm
[Mon Nov 25 10:01:57 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/java/awt/KeyboardFocusManager.class
[Mon Nov 25 10:02:11 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/oracle/ewt/alert/resource/AlertBundle_en
_GB.class
[Mon Nov 25 10:02:11 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/oracle/ewt/alert/resource/AlertBundle_en
_GB.properties
[Mon Nov 25 10:02:15 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/oracle/sysman/vt/console/app/ConsoleBean
Info.class
[Mon Nov 25 10:02:15 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/sun/beans/infos/ConsoleBeanInfo.class
[Mon Nov 25 10:02:15 2002] [error] [client 192.0.0.120] File does not exist: /u0
1/app/oracle/product/9.2.0/oem_webstage/oracle/sysman/emSDK/client/appContainer/
WebApplicationBeanInfo.class
I have tried reinstalling Oracle website, however this made no difference.

Can you ping the server which is running OEM from the client NT machine?
Are you trying to connect using DNS or IP?
Verify that this works first.

Read from socket failed: Connection reset by peer

On Solaris 10 SPARC I have NO problem with establishing SSH connections.
Here is proof:
# svcs -a | grep ssh
online Jun_02 svc:/network/ssh:default...but here is what can be found in /var/adm/messages
Jun 7 04:09:16 my_host sshd[11701]: [ID 800047 auth.crit] fatal: Read from socket failed: Connection reset by peerTHIS IS IMPORTANT!!!
This messages does not appear during I establish my ssh connection. It appears irregular.
Does anyone know whats going on ?

Hi Darren,
that would make sense but I just made a test:
I have opened tail -f /var/adm/messages and from other host:
- telnet to it on port 22 - no message
- closed client during establishing connection - still no message
But I belive you must be right as I see no other possibility...
Can I turn on more detailed logger in message to be able to see IP address of all host who are trying SSH connection ?
Edited by: czezz on Jun 25, 2009 10:50 PM

How to Disable "Connection Failed Connection Unava...

Ok I have a 808 bought it as a camera
after it updated it, I get this unacceptable repeated popup
"Connection Failed
Connection Unavailable"
Its like every 30 seconds
Its total black background message occupies valuable screen real estate at the top of the screen and repeatedly hinders normal usage of the device, causing especially unpleasant experience when capturing pictures or video.
How do nokia users like me go about disabling this message and continue enjoying the experience of the brand we choose to trust?

As someone who uses an 808 as my main phone on a daily basis due to it's fantastic quick and efficient OS, battery life, call quality, sat nav and great media experience it is beyond me why anyone would waste a huge amount of money just to use it as a camera !! However , if you go to settings then profiles and select offline mode, the phone will not attempt to connect to anything.
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Jdbc fails connection

I am trying to send an array to a pl/sql module but for some reason i am unable to get the connection object.
Here is the line of code that fails
Connection conn = null;
ArrayDescriptor rectabDescriptor = ArrayDescriptor.createDescriptor("CCS21_CONSIGNMENTLIST_TYPE",conn);   <<FAILS HERE<<
ARRAY awbNoHwbs = new ARRAY(rectabDescriptor,conn,childLessAwbs);
ARRAY hwbs = new ARRAY(rectabDescriptor,conn,hwbList);
OracleCallableStatement cst = (OracleCallableStatement)conn.prepareCall(stp.SUBMIT_CONSIGNMENT_STORED_PROC);
               Here is the stack trace
java.lang.ClassCastException: org.apache.tomcat.dbcp.dbcp.DelegatingCallableStatement
     at com.acbt.ccstt.data.accessors.ConsignmentDAO.submitDeclaration(ConsignmentDAO.java:301)
     at com.acbt.ccstt.presentation.events.consignments.select.SubmitDeclaration.midAction(SubmitDeclaration.java:68)
     at com.acbt.ccstt.presentation.events.CCS21EventAction.execute(CCS21EventAction.java:36)
     at org.apache.struts.chain.commands.servlet.ExecuteAction.execute(ExecuteAction.java:58)
     at org.apache.struts.chain.commands.AbstractExecuteAction.execute(AbstractExecuteAction.java:67)
     at org.apache.struts.chain.commands.ActionCommandBase.execute(ActionCommandBase.java:51)
     at org.apache.commons.chain.impl.ChainBase.execute(ChainBase.java:190)
     at org.apache.commons.chain.generic.LookupCommand.execute(LookupCommand.java:304)
     at org.apache.commons.chain.impl.ChainBase.execute(ChainBase.java:190)
     at org.apache.struts.chain.ComposableRequestProcessor.process(ComposableRequestProcessor.java:283)
     at org.apache.struts.action.ActionServlet.process(ActionServlet.java:1913)
     at org.apache.struts.action.ActionServlet.doPost(ActionServlet.java:462)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:647)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:729)
     at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:269)
     at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:188)
     at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:213)
     at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:172)
     at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127)
     at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:117)
     at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:108)
     at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:174)
     at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:875)
     at org.apache.coyote.http11.Http11BaseProtocol$Http11ConnectionHandler.processConnection(Http11BaseProtocol.java:665)
     at org.apache.tomcat.util.net.PoolTcpEndpoint.processSocket(PoolTcpEndpoint.java:528)
     at org.apache.tomcat.util.net.LeaderFollowerWorkerThread.runIt(LeaderFollowerWorkerThread.java:81)
     at org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:689)
     at java.lang.Thread.run(Thread.java:595)And here is my connection config
Struts Web.xml file
<resource-ref>
      <description>Oracle Datasource</description>
      <res-ref-name>jdbc/ccs21db</res-ref-name>
      <res-type>javax.sql.DataSource</res-type>
      <res-auth>Container</res-auth>
     </resource-ref>Metainf/context.xml
    <Resource name="jdbc/thedb" auth="Container"
              type="javax.sql.DataSource" driverClassName="oracle.jdbc.OracleDriver"
              url="jdbc:oracle:thin:@xxx.xxx.xxx.xxx:1521:dbsid"
              username="xxx" password="xxx" maxActive="20" maxIdle="10"
              maxWait="-1"/> Edited by: ziggy on Sep 26, 2008 4:02 PM

ziggy wrote:
OracleCallableStatement cst = (OracleCallableStatement)conn.prepareCall(stp.SUBMIT_CONSIGNMENT_STORED_PROC);
java.lang.ClassCastException: org.apache.tomcat.dbcp.dbcp.DelegatingCallableStatement
Why are you casting CallableStatement to OracleCallableStatement? The JDBC API is intented to be completely implementation independent. Never cast interfaces to implementation specific classes, it will break your app sooner or later.

Smtp failed connection attemp

Similar Messages

Maybe you are looking for