SMTP for Cisco IAC 3.1

Hi all
Where do I change the smtp server information in a portal which is already installed and running?
Regards
/O
Otavio Augusto

Locate the file
C:\jboss-as-7.1.1.Final\standalone\deployments\RequestCenter.war\WEB-INF\classes\config\newscale.properties
Change the value for
ObjectCache.email.host
From M. Dupont:
It is also critical to set the actual return email address. In 3.1 this is done in the System Setup portal page in the System Settings tab. There is a task named Set System Email Account.

Similar Messages

Cisco IAC 3.1 - problems running Conf Wizard

Hi all
Following the configuration guide for Cisco IAC 3.1, I have all steps required for executing the configuration wizard in place but, for some reason, it fails to discover the infrastructure items through the wizard. I could discover and register the infrastructure items through the Manage Cloud Infrastructure portlet.
During the discovery process, I should expect communications between CP and CO, right? I see no new process starting at PO during the discovery process.
Any hints on what might be happening ?
Thanks in advance

Yes. The documentation actually indicates that PowerCli is a requirement. It is installed along with all the other requirements.
I believe this conf wizard issue comes from the SE 3.0.1 release. It was know that one had to log out, close the browser and then log back in so that the next wizard step could be performed. Terrible for a UI experience but hope it will be fixed soon.
Thanks for your support.

Configurar smtp en cisco RV110W for scan spiceworks

Configurar smtp en cisco RV110W for scan spiceworks
This topic first appeared in the Spiceworks Community

Hi,
Could you please try to put another DNS server on the ESA? Like ISP's DNS or a public one.
Luis Silva

Mail and SMTP server settings of ASA Certificate Authority for cisco anyconnect VPN

Dear All,
i have the folloing case :
i am using ASA as Certificate authority for cisco anyconnect VPN users,the authentication happens based on the local database of the ASA,
i want to issue a new certificate every 72 hours for the users ,and i want to send the one time password via email to each user.
so what the setting of the mail and smtp server should be ,
was i understand i should put my smtp server ip address then i have to create the local users again under(Remte VPN VPN--Certificate management--Local certificate authority --Manage user Database) along with their email addresses to send the one time passsword to them via their emails.
i sent the email manually ,hwo can automate sending the OTP to our VPN users automatically vi their emails?
Best regards,

Thanks Jennifer.
I did manage to configure LDAP attribute map to the specific group policy.
Nevertheless, I was thinking whether I can have fixed IP address tied to individual user.
Using legacy Cisco VPN Client, I can do it using IPSEC(IKEv1) Connection profile, where I set Pre-Shared Key and Client Address Pools. Each Client Address Pools has only 1 fix IP address.
Example: let say my username is LLH.
Connection Profile for me is : LLH-Connection-Profile, my profile is protected by preshared key.
Client Address Pool for me is : LLH-pool, and the IP is 172.16.1.11
Only me know the preshared key and only me can login with my Connection Profile.
Using AnyConnect, I have problem. User can use any connection profile because I cannot set preshared key for AnyConnect. In that case, I cannot control who can use my Connection Profile and pretend to be me.
Example:
AnyConnect Connection Profile for me is : LLH-Connection-Profile, without any password
Client Address Pool for me is : LLH-pool, IP is 172.16.1.11
Any body can use LLH-Connection-Profile, login with another user name, let say user-abc which is a valid user in LDAP server. In that case, ASA assign 172.16.1.11 to user-abc and this user-abc can access server which only allow my IP to access.
I hope above description can paint the scenario clearer.
Thanks in advance for all the help and comment given.

Alarm smtp in cisco prime

Hi,
I want to configure the smtp in cisco prime for receive alarm message in my account .than ,when i press the test button ,the following message is display.
Failed to send mail to primary SMTP server. Please make sure that you save mail configuration by hitting 'Save' button.
think's

http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/1-2/user/guide/prime_infra_ug/maint_sys_health.html#pgfId-1059487

Contacts search for cisco Jabber for Windows & MAC

Hello,
Please assist on given below query !!
System Deatails of CUCM & IM Presence Server
CUCM:
1> System version: 9.1.1.20000-5
2> VMware Installation: 2 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 4096Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with IM & Presence
IM & Presence:
1> System version: 9.1.1.20000-5
2> VMware Installation: 1 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 2048Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with CUCM
Requirement:
1> User Search base for Cisco Jabber for Windows & MAC Client
2> Will we able to get contacts list(Jabber For windows & MAC) as like "Lotus Sametimes" for all users?
Every reply would highly Appreciated!!

Hi Karthik,
Thanks for your reply!
I have gone through the link but query is different actually, please assist on below query and provide any document links if possible.
1> The contacts does not appear when I perform a search
2> Do I required to integrate LDAP for same? If Yes Then Do I need to perform integration with CUCM Or IM & Presence? Or Only CUCM? Or only IM & Presence? (Please post a link to perform same)
3> Please also provide If any specific system requirement for LDAP server.
4> Is it possible without LDAP integration?
It is really urgent and every post would highly appreciate..........

No variable audio output for Cisco CHS 435HDC set top box.

Background: Until the other day I had my stb connectected to a TV, using TV sound, with an HDMI cable. The P265v2 remote volume control changed the TV volume. No problems.
My new TV & home theater system was recently installed. We don't use the TV speakers. While my first preference was to program the Verizon remote to change the volume on my Onkyo receiver, this did not appear to be an option on the remote's programming instruction page on the Verizon website. Instead, I am directed to change a setting on the remote that makes the Verizon remote change the stb output volume vs the tv volume. I changed the setting on the remote and ensured the stb box was set up for "variabe" audio output.
Problem: Using the stb variable audio settings, volume settings 1 through 30 produce the same volume. (Volume setting 0 produces no volume, as one would hope.) It appears the "variable" setting isn't producing a variable output as it should be on this unit.
Thinking that maybe the receiver was complicating the sitation, I tried connecting the stb to the old TV and the new TV directly and had the same results.
Now, while I am watching TV, I need to have the receiver remote at hand in addition to the Verizon remote. It would be nice to have the volume be adjustable as it should be while using the Verizon remote. I don't like the idea of using a seperate universal remote because then I would lose some of the functionality that the Verizon remote provides when watching TV, using the DVR, watching on demand, etc.
I would like to know if this is a problem just with my unit, or if it exists with all of these units, which would hopefully be fixed with a Cisco/Verizon firmware update soon, hopefully.
Thank you.

soups230 wrote:
Having same issues with hdmi and optical. Any fix to this.
Hello,
In order to control the volume on your home theater system, you'll need a FiOS TV Universal Remote that has the 4-buttons on the top for 'DVD', 'Aux'iliary, 'TV' and 'STB'. The audio receiver would have to be programmed into the FIOS TV Remote, and controlled using the 'Aux'iliary button.
Verizon's 4-Button Universal Remote Controls are available for purchase:
a) online via www.verizon.com/fiosaccessories
OR
b) at a local FiOS TV store (call first to check if they have them in stock). For a list of stores: http://www22.verizon.com/support/residential/tv/fiostv/general+support/account+issues/questionsone/8...
Presently, the default remotes for new set top boxes are the 2-button P-265 (newer version) remotes.
Regarding a problem with HDMI/optical on Cisco 435 STBs, check out the following:
Go to this webpage: http://www22.verizon.com/Support/Residential/TV/FiOSTV/Receivers/Equipment+Issues/QuestionsOne/12839...
Click on the link for 'Cisco CHS 435 HD DVR User Guide'.
Open the PDF and go to page 22 for 'Connecting to a Home Theater System...'.
Hope this helps!

How do I find the SMTP for my email acct on Firefox

I am trying to activate MS Outlook for facilitate business communication. I need to know the SMTP for the outgoing mailserver used by Mozilla for my business email acct.

Mozilla is not an email provider.
To get the email details such as mail servers, you need to contact the company that provides the email service. This could be your ISP if you use their email, or if it is a webmail service such as Gmail or Hotmail you need to contact the provider of the webmail service.

How to configure SMTP for iCloud?

I have never used the Mail program on my macs. I started using Eudora in 1995 and when Mail came along some years later, i didn't take to it, it didn't have the functionality i needed and enjoyed. Fast forward to a couple days ago, my Snow Leopard MacBook is wearing out and i got a new MacBook Pro running Mountain Lion. When i was setting up the new computer, i thought iCloud would be configured automatically. It wasn't because i have a couple of different Apple IDs but i think that is straightened out now and i'm signed in using the me.com email address and have my calendars and contacts syncing with iphone and my other computer. Mail is working, but only for my me.com email address which i rarely use. I mainly use a gmail address.
I don't want to use Mail and i don't want mail to be downloaded to it. That happened on my other computur, so that i had tens of thousands of messages in a program i never open and don't use. So i somehow turned it off so it no longer gets the mail from my other accounts. i don't want to receive email in Mail. But because i can't use Eudora in Mountain Lion, i need a new email client. Today, i downloaded and installed Mail Mate, i want to try it out. When I tried to use Mail mate to send an email i got a message saying "No SMTP server configured for iCloud." i googled how to configure SMTP for iCloud and what i found said it configures automatically. So i don't know what to do. I went to ICloud in system preferences and i don't see anything i can do there.
Is there anything i can get it to do to configure automatically? All my software is up to date, if that makes a difference.

i was persistently googling search terms for this problem and came across a link that gave information to the effect that for non Apple email clients, SMTP has to be configured manually, and the settings were provided. I entered them into Mail Mate and now it works. So thankfully, this problem is solved.

What Service Restarts the Data Calculations for Cisco Supervisor Desktop and Wallboards

Hello All,
UCCX version 8.0.2.11005-20
UCCX is running in HA mode.
Yesterday we believe our UCCX Servers failed over due to a network outage between the Publisher and the Subscriber.
So last night I restarted the "CCX Engine" to fail-back the servers, which worked just fine.
Now today the database that our Wallboard uses is not showing any data. So I ran some SQL statements on both Servers' CLI and the Database db_cra is showing old data on the Subscriber and the Publisher is showing all Zeros. But after just looking at the Real-Time Reporting page on the Web GUI, that "seems" to be working but I'm not positive because I have nothing to compare the numbers to...
When I try to run Supervisor Desktop, I can open the Program, sign-in, and then when I choose the "team" and then try clicking on a CSQ Name, Supervisor freezes and I get a "Not Responding" message. I thought it was just my PC but this is happening for 2 other people as well, on 2 completely different PCs so I can rule out that its the computer that is killing Supervisor.
Is there another service that needs to be restarted in order to get this working? I tried restarting the service for "Cisco Desktop Recording and Statistics Service" and I was nervous about restarting anything else because we are currently open and our CallCenter is taking calls.
Any thoughts would be much appreciated!
Thanks in Advance,
Matt

Has your problem cleared up? Did you do anything, such as a reboot or open a TAC case?
Anthony Holloway
Please use the star ratings to help drive great content to the top of searches.

Rrack mounting brackets for Cisco switch SF300-48P ?

Does anyone know how to get rack mounting brackets for Cisco switch SF300-48P ?

You might be able to get them through Cisco support. Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-mount-brackets

RAID Configurations for Cisco servers

Hi All,
What is the RAID configuration for Cisco Appliance(Version 8.5) like CUCM, CUPS, CUIC, Unity etc?RAID Configuration will be done while installtion itself or we need to do it explicitly?
Regards,
Adithya

Hi Geoff,
Thanks for the reply. Just wanted to know whether if this RAID configuartion is similar to the other server RAID where we install Cisco applications.(Like OS & Application Software is RAID 1 and Database is RAID10).
Regards,
Adithya

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

Has anyone develped an EM plug-in for Cisco switches or routers

Folks,
Has anyone develped an EM plug-in for Cisco switches or routers? Please reply to this thread if you have developed one and would like to share your experience in developing this plug-in?
Thanks,

It's probably not the conversion from CMYK to RGB that's causing the problem, but color profile (ICC) embedding in Photoshop. Fireworks doesn't read color profiles. You might be able to create an action to remove the color profile in Photoshop and then batch process the images with it.

SMTP for Cisco IAC 3.1

Similar Messages

Maybe you are looking for