SMTP Mail Configuration-Need Help

Hi Experts,
We have ECC 6.04 on Linux Redhat. we need to enable mail communication from SAP however our mail server is in different network/domain. is it enough to open the ports for mail communication?
kindly clarify.
Regards,
Pradeep

Thanks RB,
so I need to do the following,
1. Need to open ports for mail communication between two servers.
2.Need to SAP IP addresses in relay server
Other than these anything needs to be done?
Thanks a lot,
Pradeep

Similar Messages

Can we provide UN and pwd Authentication 4r SMTP Mail Configuration

Dear All,
Previously we are able to send the mails from SAP to Outside World. After chaning the Mail Server to MS Exchange 2003
We enabled the Port the 25.
We are facing a problem While configuring a mail via SMTP for Exchange Server 2003.
Throws an Error Message:
Internal error: CL_SMTP_RESPONSE ESMTP error code is not known. 554 554 > : Recipient add
As per network Team :
Unless we provide a Username and password, the Send/Receive process does not happen.
Is there any option in SAP - SMTP Mail Configuration to Provide user and password Authentication.
I searched in SDN as well as in market place. but i could not succeed. Please guide me the process.
Regards
SNB.

Hi we are configuring Google SMTP getting below error..
No delivery to xxx.com, authentication required
Message no. XS856
Diagnosis
The message was processed successfully in the SAP system. The mail server that is to receive the message for further processing requires authentication. Probably there is no logon data specified in the SAPconnect configuration.
Information from external system (if available)
smtp.gmail.com:587
530 5.7.0 Must issue a STARTTLS command first. i91sm11178241qgd.25 - gsmtp
Procedure
Enter the logon data in the SAPconnect node.
Using Gmail SMTP server using "smtp.gmail.com" with port 587
Please advise.
Regards,
Sudarshan

SMTP Mail Configuration error

Dear Folks,
after SMTP mail Configuration
i can send mails to Internal mail id
but i got dump to send External mail id
Internal error: CL_SMTP_RESPONSE ESMTP error code is not known. 554 554 : Relay access d
pls give me suggestion to resolve this issue
regards
satheesh

Hi ,
Please check the below note it will solve your issue::
Note 693306 - Error analysis for e-mails and fax sent via Service Manager.
Also as it says permision denied that means you have to check with your network team to check for proper access to cross firwall.
Thanks..
Mohit
Edited by: mohit gupta on Oct 1, 2009 8:53 AM

A erase my e mail account, need help pls

a erase my e mail account, need help they werw my job e MAIL

It's a disgraceful failure of any customer service by BT. Had my Btinternet email account since they launched backin ... was it 1997? Everything digital in my life is spidered into the account now. Its been used as my registration point for virtually everything for the past fifteen years. And now getting less than 30 days notice to try and find every single product and website I have registered with and then change all my details?!?!? Hell, I'd need about a year to do so; and then I would still probably have missed some! By their actions, they potentially cutting me off from products that I have purchased & tied to this email address.
Add to that the fact that their email that comes into your inbox sources from some dodgy 'analytics planning' website, as all the links route through there... I had serious doubts as to its legitimacy and forwarded it to their abuse contact & opened a case regarding it. Highly unprofessional of them - especially when you consider that we are repeatedly advised by BT to never click on links unless we are sure of their validity. And should never, ever, enter our account details on any other site other than theirs.
Shoddy BT, very very shoddy. I would expect a higher standard of business from such a company. And would definitely expect a proper notification click through to come up regarding this service change when I log into email. I would say a good proportion of their users will deregard the email as a phishing attempt. **bleep** cowboy operation.

SMTP Mail configuration in WDS server

Hi,
My company has more than 9000 desktops in which normally on day basis more than 100-150 systems will go deployment via WDS (MDT 2013) in server 2008r2 (DHCP is also configured in the same server), Where as i need to configure a SMTP mail server which will
export the lease expiration(currently reduced from 24hrs to 8hrs of lease period) data with hostnames & IP details and send it to my mail id.
I am very least experienced in this domain, Kindly suggest the ideas to implement the same.
Why required ?
To monitor the number the images being deployed on a given day.
No systems should reflect more than 1 day in the imaging vlan.
Manual efforts and incidents can be reduced if implemented.
Thanks,
Satheeshkumar C

Hi Satheeshkumar C,
As far as I know there don’t have the original option can achieve your propose, when the DHCP lease expiration, may you can choose third party application, and this forum is
mainly for WDS related issue it’s not the best place to talk about the MDT issue, there have a specific MDT support forum you can post in MDT support forum and get the MDT expert further support.
MDT support
forum:
https://social.technet.microsoft.com/Forums/en-US/home?forum=mdt
SMTP E-mail
https://technet.microsoft.com/en-us/library/hh831469.aspx
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Smtp mail configuration

I'm trying to configure my exchange server to work with SugarCRM. SugarCRM is asking for smtp mail server information. and, I know my mail server address, but I'm not sure how to configure my exchange server or check to make sure the appropriate
configurations are set up for this to occur.

Hi ,
Please try to telnet the exchange server ip from the sugarCRM application . If it happens successfully just try to send an test email to anyone of the exchange recipient in our oraganization from the sugarCRM application via telnet command .
Note : You should have to send an email to internal recipient otherwise exchange will not allow .Because basically exchange server will have receive connector closed for open relay .If you wanted to send email to the external recipient like gmail or yahoo
you need to create a new receive connector and you have to open an relay for an particular ip address of sugarCRM application .
Sometimes application servers will have two network adapters .So on that scenario please check the respective ip address added on the exchange server receive connector is an primary ip address for sugarCRM application server .
For open relay please refer the below articles .
http://blogs.technet.com/b/exchange/archive/2006/12/28/3397620.aspx
please reply me if you have any queries .
Regards
S.Nithyanandham
Thanks S.Nithyanandham

Odd mail issues, need help

A couple of things I need help with.
1) Mail constantly goes offline and pops up a dialog box asking for my password. I enter my password in the box and hit okay and it doesn't take. I can hit cancel and put mail back online but that's a pain. What is causing that and how do I fix it?
2) People send me mail and then about 30 min later I get the same email again. This problem doesn't happen with every email, just some.
I have no mail rules on. and I run virus software and it's fine.
Can someone please help me on this. Thanks!
1.25 GHz PPC G4 / 20" Mac OS X (10.3.9) 768 MB DDR SDRAM, iSight camera, Wacom Tablet

Open /Applications/Utilities/Keychain Access, choose Keychain First Aid from the application menu, and proceed to repair the keychain. If that doesn’t work, you may try removing the password entry from the keychain and letting Mail create it again.
Also, in Mail open Help > Mail Help and read the article titled “Mail keeps asking for my keychain password”, in case it applies to you. There is a related article titled “My password is not saved” that you may also want to read, but beware that the last suggestion provided there (deleting the mail account) is wrong and could cause irretrievable data loss if this was a POP account.
Note that Mail doesn’t always correctly report what the problem really is. If Mail can connect to the server but cannot log into your mail account for some reason, it’ll ask for your password, regardless of whether that’s really the problem or not. Don’t keep entering the password every time, because that’s not the problem (click Cancel instead, and take the account back online afterwards).
What’s the time interval chosen in Mail > Preferences > General > Check for New Mail? If it’s set to Every minute, try changing it to Every 5 minutes.
Go to Apple Menu > System Preferences > Network, choose Network Port Configurations from the Show popup menu, and make sure that the configuration used to connect to Internet appears at the top of the list.
Also, try using a different method to connect to Internet, if possible, or connecting the computer to Internet as directly as possible, i.e. bypassing any routers that might be present, using an ethernet cable instead of wireless, etc., and see whether that makes a difference.
BTW, if you’re using Mac OS X 10.3, as your profile indicates, it would have been more appropriate to discuss this in the Mail & Address Book - Mac OS X 10.3 & earlier forum. If the discussion applies to both Mail 1.x and Mail 2.x, it doesn’t really matter, but it’s difficult to know that in advance.

Dictamus smtp mail server question - help!

I'm just wondering if anyone else is having trouble using Dictamus on their iphone for sending dictations via email.
I recently put OS 5 on my iphone and I have upgraded to Lion on my imac. I recorded a dictation the other day on my phone and I tell it to send and it looks like it does but no one is getting my dictations in their email. I have tried troubleshooting and checked my SMTP settings and they seem to be correct.
I used to be able to send dictations no problem before I uprgraded - is anyone else having this problem of their emails not being sent?
I use a me.com account and would like to use that to send the emails. I have the smtp sever set to smtp.me.com and I have also tried smtp.mail.me.com and still my emails will not go thru.
Any suggestions or help is much appreciated.

We have been getting reports from quite a few MobileMe customers who cannot send mails from Dictamus. According to our investigations, Dictamus does send those mails correctly, and the me.com SMTP server acknowledges having accepted them for delivery. This is as far as anyone can track outgoing e-mail over SMTP, so Dictamus flags the respective dictation as "shared successfully". The problem is that after that initial acknowledgement, MobileMe silently discards some Dictamus mails (not all) without notification to either sender or recipient. This can happen if either recipient or sender are on MobileMe, so sending from a MobileMe address to another mail provider is subject to this issue as well as sending from another provider to MobileMe. Therefore, we currently recommend against using MobileMe accounts for sending mails from Dictamus. We are unaware of similar problems with any of the other large e-mail providers.
Michael Nagel
JOTOMI

WRT54GS cannot be configured, need help!!!!

Ok.. I am getting so lost. I will try to explain the best I can what is going on. I just bought the Wireless G router with speedbooster and put the CD in to set it up, did everything it told me to do on the screen as far as pluggin cables in yada yada. When it came to step 4 of 4 it said "Waiting for Router". Then after about 2-3 minutes it comes back saying the following:
YOUR ROUTER DOES NOT APPEAR TO BE CONNECTED PROPERLY
Error 322: New router or Gateway not detected
Follow these steps:
1) Make sure you are connecting your new router and not your old router
2) Make sure the ethernet cable from your computer is securely connected to a LAN port on the back of your new router
3) Click retry to try installing your router again
Also, when I try to retry the setup without unplugging anything it says this:
Linksys EasyLink Advisor Setup Wizard has discovered that you are already connected to a router. Many people choose to replace an existing router with their new Linksys Router.
I can connect to the internet without configuring the router!!! It isn't secure though! I want to configure my router so that it is secure and I don't know what to do to fix this.
I am using a Comcast provided modem, RCA model # DCM425
Any help would be greatly appreciated... Remember I am a noob so please don't confuse me more with words I don't understand.. Thanks
One more thing. When it is "Waiting for router" the 2 computer icon comes up at bottom of screen saying acquiring IP address so I double clicked on it and it would be connected with the IP address 192.168.1.1 and then all of a sudden it would say Invalid IP address not connected. I really need help here!!!

Ok, I'm not 100% sure I can help you, but I will try.
First thing, find the setup disk that came with the router and use it as a coaster or a frisbee or something because it is almost completely worthless.
Until you have completed the setup of the router, I would suggest using a computer that is connected directly to the router via ethernet cable. The reason being, if you change any settings wirelessly, such as security features, you will be disconnected and unable to access it again. So use a computer that is directly connected for setup.
The IP address you saw in you system tray is the IP address of the router itself. You actually need this for your router setup. Open whichever web browser you use and type in that IP address, nothing else. 192.168.1.1 A login screen should appear for you to enter your user name and password. Leave the user name blank and for the password enter "admin" without the quotes. This should bring you to your basic settings screen for the router.
From this point, I'm sure exactly how you want to set everything up. If you're not very familiar with networking or routers I would suggest you change very little. If you desire security for your network (which I suggest) click on the "Wireless" tab at the top of the screen. This should bring you to basic wireless settings. From here, you can change the name of your wireless network, change the broadcast frequency and enable/disable wireless broadcast. You can change these if you like or leave them alone whichever you prefer. I do suggest changing the name of you network (SSID) so you can tell which one is yours when you try to connect. It gets confusing when everyone in your neighborhood has a Linksys and all of the names look similar.
Once you're done here, next click on the "Wireless Security" tab within the "Wireless" tap. Make sure you are click "Wireless Security" and not just "Security." From here, you can select the kind of wireless security you want to use. I'm not highly informed on which of these is the best, but WEP is probably the strongest security you're going to need anyway, so I would go with that. After you select WEP you get a few more options. For "default transmit key" just select one. Then in the "WEP Encryption" drop down, select "128 bits 26 hex digits." 64 would most likely be ok, but 128 bit encryption is definitely better.
In the next box "Passphase" enter a word or short phrase that is only known to you an click generate. The four boxes below will now have you WEP keys. I delete all but the first key to keep things simple, but whatever you want to do is up to you. After you delete the other three lines, select the key in your first line and select/copy it so that you can just paste it into the box in network options when you're connecting to the network. Regardless, I would also write this key down somewhere. If you have multiple computers in the house you have to enter it on each and every one and it's a pain to go back and forth. Click save settings. You're pretty much done. There are other things you can do to beef up security, but this is the most basic and it's still quite strong.
If you are looking at playing games frequently or anything like that I would go to PortForward.com
Any other questions you have, you should be able to google I think. I hope I can help. Good Luck.

File to Mail Scenario - Need help

Hi all,
I am trying a simple file to mail scenario in which i am using following data types .
Source datatype -
Scr_File_DT
-- Root
Material_no
Plant
Target datatype -
Tgt_Mail_DT
--Content
In the message mapping i am concatenating material_no and plant and mapping it to content.
The receiver mail adapter parameters are as follows -
Transport protocol - SMTP
Message Protocol - XIPAYLOAD
URL: smtp://gmail.com
Configure User Authentication: X (Check box is selected)
Authentication Method: Plain (from drop-down box)
User: [email protected]
Password: ****
from: mail address
to: mail address
subject : test mail.
Just wanted to confirm whether these settings are correct or not? Because i am not getting the mail in my mailbox.
Can anyone please help me on this.
Also are there any other settings required for using mail adapter ?
Thanks.

Hi,
you should add your email address to your user,add specific users list add you r user in alrtcatdef.
generally you should maitain the email data type format like
subject,from,to,content-type..
se below link
http://help.sap.com/saphelp_nw2004s/helpdata/en/23/c093409c663228e10000000a1550b0/content.htm
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/1685 [original link is broken] [original link is broken] [original link is broken] [original link is broken]
/people/michal.krawczyk2/blog/2005/03/07/mail-adapter-xi--how-to-implement-dynamic-mail-address
Regards
Chilla..

Incoming mail blocked need help

hello, all, I cannot receive email on the wifi servers at work, they block all email coming and going. As I recall, there is a program/service that allows you to receive and send mail from wifi servers, even blocking servers, something like auth smtp. However, their website says they can only send email, not receive email. Since I don't have 3G, need to receive email via wifi, any suggestions? thanks

Thank you very much Weth. I do have a current active Verizon account, with my iPhone 4S active on this account. Do I just need to call Verizon from Costa Rica to ask them again to unlock my phone? Is there a special number to call at Verizon to unlock phones? Thank you again. This is helping.

Cox mail issues- need help

I have had my Iphone for 10 days and I still can't send mail through Cox (my provider). I have been able to receive email, but never send.
Error message: Cannot Send Mail
connection to the serve failed.
Anyone have any ideas for me as to why I can't send, yet I can receive email?
I have confirmed the server for cox in my region.
Cox offers no help.

Then you should probably explore a free GMail account and use their SMTP servers. They work in WiFi and EDGE with no issues. They support Authentication AND SSL. Here are the instructions I followed. They may help you.
First, create a free GMail account. Once you create it, log into it via the web, and enable POP access under Settings.
Also under Settings, go to the Accounts tab and add your COX email address as an authorized account. GMail will validate that account by sending you an email with a verification code. Retrieve the email and code, and enter it when prompted by GMail, and that will allow you to use GMail's outgoing server with your COX ID as an reply-to address.
Next, go to your iPhone. I suggest you delete and recreate the account from scratch.
1. I went into Settings / Mail / Add Account and chose OTHER.
2. I chose POP, then put my name under NAME, my custom ID ([email protected] in your case your COX ID) under ADDRESS, and "COX Email" under description. (The important thing here is to use your custom address, not your GMail address).
3. Under incoming server, I put pop.myserver.com (your COX pop server), and my login ID and password (again, your COX ID and password).
4. Under outgoing server, I put smtp.gmail.com, [email protected], and my Gmail password. This is the only spot you need your GMail account and password.
5. I hit save.
Done. SSL and authentication are automatically set. I just tested it and sent myself an email, and it went out and came back as [email protected]
I think deleting the account you have now and recreating it should do the trick. You dont even have to delete your old account - just turn it off, and create a new one to test.

Cap on Mail? Need help, important

Ok, so I have a gmail account and so does my business partner. I have been working on a single photoshop file that is about 128MB. I am trying to send it to him via e-mail, but I keep getting two problems. Either I keep getting a message from Mail at the bottom of my e-mail saying that my e-mail message is too big, can only be 15 MB or so. Or I get the message that it can not connect to my out going server. I have tried about 6 different networks with different SMTP's. Keeping in mind that normal sized e-mails are going through with out a hitch.
Any help would be greatly appreciated.
Thanks in advance
-Tim

Nothing to do with Apple mail - it's the amount of data a service provider will allow you to send as an email - 128Mb is huge. It's a bit like putting a load of stamps onto a sofa and then trying to get it into a mail box - they won't take it.
Email was never designed for large scale file transfer. Your possibilities are to upload the file to a free or paid for file hosting site - .mac for example will you to post a file for others to download, or to split the file into manageable chunks - using something like machacha and sending those by email. your recipient can then put them back together at the other end.
Have a think about it and if you need more advice, come back.
Good luck.

Cannot Send Mail - Error, Need help!

I can not send e-mail. Error message reads,
"The recipient "[email protected]"was rejected by the server."
Initialy I was getting an error message about "Authentication" but when I took User Name and Password for SMTP, that error disappered, but now I'm getting the above message.
Did anyone figure out the trick to get around this and send e-mails out?
eMachine Windows XP
eMachine Windows XP

AlexMaeda,
This article has more information:
http://docs.info.apple.com/article.html?artnum=305634
As for an email provider allowing customers to relay outside of their network, many email providers, set up an authenticating SMTP server on different port. The article above includes information on specifying the port to use.
For example, .Mac accounts can use port 587 as discussed in this article:
http://docs.info.apple.com/article.html?artnum=75124
You may want to check with your email provider if they offer an authenticating smtp server for people who are traveling or using mobile devices. Many do so without any additional cost, some may charge for access to that service.
Hope this helps,
Nathan C.

Java mail overhead -- need help

I am using javamail to send out email with attachments, but I found a heavy overhead using it. The file I am going to attached to mail is 13MB, but after I build MimeMessage object, it becomes 18MB. The following is piece of my code, any help is appreciated.
public static void send(String host, String to, String from, String subject, String message, Collection fileNames) throws GLPMException {
// create some properties and get the default Session
Properties props = System.getProperties();
props.put("mail.smtp.host", host);
Session session = Session.getDefaultInstance(props, null);
session.setDebug(false);
try {
// create a message
MimeMessage msg = new MimeMessage(session);
if (from != null) {
if (!from.trim().equals("")) {
msg.setFrom(new InternetAddress(from));
InternetAddress[] address = InternetAddress.parse(to, false);
msg.setRecipients(Message.RecipientType.TO, address);
if (subject != null) {
msg.setSubject(subject);
// create and fill the first message part
MimeBodyPart bodyPart = new MimeBodyPart();
if (message != null) {
bodyPart.setText(message);
Multipart multiPart = new MimeMultipart();
multiPart.addBodyPart(bodyPart);
// attach the files to the message
if (fileNames != null && !fileNames.isEmpty()) {
Iterator fileNameI = fileNames.iterator();
while (fileNameI.hasNext()) {
String fileName = (String) fileNameI.next();
MimeBodyPart bodyPart2 = new MimeBodyPart();
FileDataSource fds = new FileDataSource(fileName);
bodyPart2.setDataHandler(new DataHandler(fds));
bodyPart2.setFileName(fds.getName());
multiPart.addBodyPart(bodyPart2);
// add the Multipart to the message
msg.setContent(multiPart);
// set the Date: header
msg.setSentDate(new Date());
// check message size before send out, if it is greater than 15M
// populate warning message to user.
ByteArrayOutputStream bais = new ByteArrayOutputStream();
msg.writeTo(bais);
logger.log(Level.FINEST, "message's size " + bais.size());
if (bais.size() > 15 * 1024 * 1024) {
GLPMExceptionMessage exceptionMsg = new GLPMExceptionMessage(
GLPMExceptionType.WARNING, IErrorConstant.EMAIL_OVERSIZE_MSG);
throw new GLPMException(exceptionMsg, GLPMExceptionType.WARNING);
// send the message
Transport.send(msg);

Open the pdf file in notepad. If it contains the line drawing characters (��), foreign characters or little boxes, it is 'binary'. Text is considered to be characters 1-127. The line characters and foreigen characters and boxes are 128-255. PDF's are 'binary' in this sense. They will have to be encoded. A common standard is MIME64 encoding which you are using.
Read more here.
http://www.winnetmag.com/Articles/Index.cfm?ArticleID=4913

SMTP Mail Configuration-Need Help

Similar Messages

Maybe you are looking for