SNMP configuration for V480

I've six SUN SERVERS. Four are V890 with Solaris 8 and the other two V480 with Solaris 10. How to configure SNMP in all these ? I want to send SNMP traps to a NMS. How to achieve it ? snmpd daemon is present in V480 machine.
Thanks
---Britto
Message was edited by:
bravobritto

Integration of Directory Server SNMP agent with Solaris Master agent is documented in the Administration Guide Chapter 14: Monitoring Directory Server using SNMP.
http://docs.sun.com/source/817-7613/snmp.html
Regards,
Ludovic.

Similar Messages

Snmp configuration for SG300

Hi,
Am trying to configure SNMP functionality for the first time on an SG300-28 switch so I can use mrtg to monitor it. I've defined no users, 2 groups (mrtg and mrtg2 for SNMPv1 and SNMPv2 respectively), both with No authentication required. Default View of Read. I also defined a Basic Community type and called it sg300, with the View Name of Default. Under Views I changed nothing; the Default has 1 Object ID subtree included.
The mrtg CFGMaker in cannot retrieve any information from the switch. I've used it before with routers, Windows servers, etc. with no problem so I have to be overlooking something specific to this switch.
Much appreciated.
--Ben

Agreed Jonathan was correct, that was the part I missed the first time through. I walked through again to make sure there wasn't anything else and have attached the notes I took, mostly so I'll have them next time I have to do it :)
Steps to configure SNMP for MRTG on SG200-26
***Note*** These are minimum steps only for a lab environment additional security settings may be required for production use.
Switch is starting at factory reset configuration state
Login to the switch
Default ip 192.168.1.254
Username: cisco
Password: cisco
Change Password
Expand SNMP Section on bottom of left navigation
Highlight communities on the expanded SNMP section
Click the Add button
Enter the IP address of the system that will be making SNMP requests to your switch
Community string: mrtg (or whatever you want to use)
Ensure Read Only is selected for your access mode
Click Apply
Click Close
Expand the Security Section on the left navigation bar
Highlight TCP/UDP Services
Click the Checkbox to enable SNMP Service at the top of the screen
Click Apply
In the top right hand corner you should see a flashing save button, make sure to save your config if your happy with it.
“Snmpwalk –c mrtg 192.168.1.254” Should now run and return
***Note*** If your looking for port numbers in the output they start with .49 for port 1 and go to .74 for port 26.
IF-MIB::ifHCOutOctets.49 = Counter64: 0
IF-MIB::ifHCOutOctets.50 = Counter64: 0
IF-MIB::ifHCOutOctets.51 = Counter64: 0
IF-MIB::ifHCOutOctets.52 = Counter64: 0
IF-MIB::ifHCOutOctets.53 = Counter64: 0
IF-MIB::ifHCOutOctets.54 = Counter64: 0
IF-MIB::ifHCOutOctets.55 = Counter64: 0
IF-MIB::ifHCOutOctets.56 = Counter64: 0
IF-MIB::ifHCOutOctets.57 = Counter64: 0
IF-MIB::ifHCOutOctets.58 = Counter64: 0
IF-MIB::ifHCOutOctets.59 = Counter64: 2849723
IF-MIB::ifHCOutOctets.60 = Counter64: 0
IF-MIB::ifHCOutOctets.61 = Counter64: 0
IF-MIB::ifHCOutOctets.62 = Counter64: 0
IF-MIB::ifHCOutOctets.63 = Counter64: 0
IF-MIB::ifHCOutOctets.64 = Counter64: 0
IF-MIB::ifHCOutOctets.65 = Counter64: 0
IF-MIB::ifHCOutOctets.66 = Counter64: 0
IF-MIB::ifHCOutOctets.67 = Counter64: 0
IF-MIB::ifHCOutOctets.68 = Counter64: 0
IF-MIB::ifHCOutOctets.69 = Counter64: 0
IF-MIB::ifHCOutOctets.70 = Counter64: 0
IF-MIB::ifHCOutOctets.71 = Counter64: 0
IF-MIB::ifHCOutOctets.72 = Counter64: 0
IF-MIB::ifHCOutOctets.73 = Counter64: 0
IF-MIB::ifHCOutOctets.74 = Counter64: 0

SNMP Configuration for Cisco Unity

Dear All,
Can you please tell me how i can configure SNMP on my Cisco Unity.
Please help me.
Regards,
Malik.

Dear All,
Can you please tell me how i can configure SNMP on my Cisco Unity.
Please help me.
Regards,
Malik.

SNMP configuration in WLC

hi all,
Can any one tell me if there is document available for SNMP configuration for WLC 4404?

http://www.cisco.com/en/US/docs/wireless/controller/7.0MR1/configuration/guide/cg_controller_setting.html#wpmkr1372608
Configuring the device via snmp is very difficult and there really isn't a document covering that. WCS uses snmp to configure the controllers.

Is it possible to obtain a report from Ciscoworks LMS3.1 to detail the SNMP configuration of all devices?

I am about to update/standardize to secure the SNMP configuration for all devices in the network utilizing Ciscoworks.
There is likely to be variations amongst the devices. Therefore, I would like to generate one report for all the devices, capturing the SNMP configurations, is this possible?
I know how to complete the work afterwards but am struggling to produce a meaningful report that I can use to build my tasks from.
I am trying to achieve this using a particular 'role based' account via ACS, so it is possible that I don't have the permissions with this account at present which maybe why I'm not able to do it.
Thanks!

Getting the SNMP trap community string is not trivial. The reason for this is that anything which shows the configuration will have this field starred out. You can get to the value, but not in a report-like fashion. You can, however, search the archived configs under RME > Config Mgmt > Archive Mgmt > Search Archive. Assuming you know the SNMP trap receiver IP, you could search on:
snmp-server host x.x.x.x old-string
That would show you all devices that still had the old community string.
If you need to force RME to get the new config data, you can simply schedule a Sync Archive job under RME > Config Mgmt > Archive Mgmt > Sync Archive. Of course, if you made the changes outside of LMS, you will need to manually update DCR with the new community string.

How to configure SNMP agent for Oracle 10g

Hello,
I've installed oracle 10g in a Windows 2000 SP4 and I want to monitor database using SNMP.
I've already installed Windows SNMP agent but I haven't any idea how to configure Oracle in order to grant SNMP monitoring.
What should I do?
Is Oracle database ready to be monitored via SNMP by default?
Thanks in advance for your help.
Regards,
Carles

Hello,
Thanks for your message.
In fact, I already found this doc in oracle, but it just show executables I have to install and my question can I install these executables.
I've already installed Windows SNMP agent, configured and testedwith disk space checkings, but it doesn't work fine with Oracle.
I launched Oracle Universal Installer and I checked Installed Products, but I haven't found how to install SNMP agents for oracle.
How can I add Oracle Peer Master Agent and Encapsulator to my oracle installation?
Thanks again for your help.
Regards,
Carles

Snmp configuration on weblogic 10 has no effect

SNMP in MMC(Mobile Management Center, A HP Product), use joesnmp.jar internal to send snmp trap generated by mmc app. This part works well in weblogic 10;
snmp in weblogic , configured by weblogic console. In weblogic 8, we configure such items:
Weblogic Subsystem
Purpose
Level
Deployer
Monitor all war/ear deploy/undeploy/redeploy
INFO
JDBC
Monitor all warnings/errors in jdbc operation
WARN
Current tests shows that the snmp configuration on weblogic 10 has no effect.
Due to MMC4.6 gets the Weblogic updated from 8.16 to 10.3, we didn’t find the configuration about “Enable JDBC Logging”. Below is the former config page about Weblogic 8.16.
But in Weblogic 10.3 we cannot find this configuration. We have followed the guide http://e-docs.bea.com/wls/docs100/jdbc_admin/monitor.html#wp1048793
And tried to set the appropriate properties on the command line like this,
-Dweblogic.debug.DebugJDBCSQL=true -Dweblogic.log.StdoutSeverity="Info"
Actually we can get the DM, Core, SMTP, Bulk, Adaptor Class, and connection fail error messages in weblogic backend log, but seems Weblogic cannot send SNMP trap messages to SNMP monitoring tool like Openview.
PS. Weblogic can send out the SNMP trap messages when the server starts and stops.
So till now the SNMP cannot monitor the DM, Core, SMTP, Bulk, Adaptor Class, and connection fail for MMC4.6.

Hi, I am on 12.1 weblogic, and I am stuck on where you set the SNMP Servername and port number.
We are on windows 2008, I see there is a services, SNMP .
Is there something I need to do on the weblogic side before i get into the SNMP agenets and traps, this part I understand, I am just unsure where to add the SNMP Servername and the user I wish the emails to go to.
I see in the security realms the user i can add to the group monitors.
-->, I am running WL 10.3 and SNMP works fine. The cluster generates traps based on particular mbeans, such as when a server's health state is not "OK", or when there are JDBC connection issues. You have to create a new SNMP agent within the admin server then build the individual traps ( String, Gauge, Counter, etc. ) and make sure you have a Trap Destination.

SNMP Query for Byspass Status (AIP5)

I'd like to monitor the state of Bypass mode for the ASA-SSC-AIP-5 and would like to know if I can check this with SNMP and if so, which OID.
I started messing with SNMP and the SSC5 a while back and started a thread about snmpwalk causing it to crash. After that, I never really picked the project back up.
I've been known to miss the obvious every now and then, but I was dissapointed to see that there wasn't an (obvious) way for the device to alert you when it automatically goes into bypass mode. This should be a feature request.

IPS provides SNMP traps for different interface conditions like link going down or up, traffic bypass started, etc. Below is one such example
Received SNMPv2c Trap: Community: "public"
From: 10.89.149.204 mib_2.1.3.0 = 38429472
snmpModules.1.1.4.1.0 = ciscoMgmt.138.2.0.1
ciscoMgmt.138.1.3.3.1.3 = 3                      <====    index can be mapped to index obtained from snmpwalk
ciscoMgmt.138.1.3.3.1.4 = 5                      <====    Traffic bypass started
ciscoMgmt.138.1.3.3.1.5 = 4
ciscoMgmt.138.1.3.3.1.6 = 38429472
All you need to do is enable sending traps from the sensor.
qssp-8085(config)# service notification
qssp-8085(config-not)# enable-set-get true
qssp-8085(config-not)# enable-notification true
qssp-8085(config-not)# read-only-community public
qssp-8085(config-not)# read-write-community private
qssp-8085(config-not)# trap-destinations x.x.x.x           <===== trap destination
qssp-8085(config-not-tra)# exit
qssp-8085(config-not)# exit
You can configure separate community name under trap-destination. If not provided then the read-write-community will be used to send with the trap.
Hope this helps
Madhu

SNMP configuration of Aironet1200 (ios based)

Hi,
Could somebody explain where I am going wrong with my SNMP configuration of my Aironet 1200AP.
I am trying to set up a new SSID, with a WEP key, some radius server info and the ability to toggle requireEAP and requireMAC on and off.
The sequence of commands I have been trying is given below, this is from the factory default config. After I blast the AP with this config, I get the following problems:
1. I cannot manipulate the SSID in the web interface any longer
2. The radius server info never shows up in the web interface
3. If I try to set RequireMac and/or RequireEAP, the set request goes through, but a get on OIDs shows them as false again.
4. I cannot associate at all with the device.
Any thoughts/help would be greatly appreciated.
Thanks
Ashleyb
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfAuxSsidBroadcastSsid.1.1 = 1
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfAuxSsid.1.1 = "MyNewSid"
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-WLAN-VLAN-MIB::cwvlWlanEncryptionMode.0 = 2
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-WLAN-VLAN-MIB::cwvlWlanEncryptionMandatory.0 = 1
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfAuxSsidAuthAlgRequireMac.1.1.1 = 1
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfAuxSsidAuthAlgRequireEap.1.1.1 = 1
snmpset -v1 -mall -cpublic 10.8.200.112 \
RFC1213-MIB::ifAdminStatus.1 = 1
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-AAA-SERVER-MIB::casConfigRowStatus.radius.1 = 4
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-AAA-SERVER-MIB::casAddress.radius.1 = 10.8.200.109
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-AAA-SERVER-MIB::casAuthenPort.radius.1 = 1812
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-AAA-SERVER-MIB::casKey.radius.1 = "secret"
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfVlanEncryptKeyStatus.1.0.1 = 6
snmpset -v1 -mall -cpublic 10.8.200.112 \
CISCO-DOT11-IF-MIB::cd11IfVlanEncryptKeyLen.1.0.1 = 13 \
CISCO-DOT11-IF-MIB::cd11IfVlanEncryptKeyValue.1.0.1 =
"zzzzzzzzzzzzz" \
CISCO-DOT11-IF-MIB::cd11IfVlanEncryptKeyTransmit.1.0.1 = 1 \
CISCO-DOT11-IF-MIB::cd11IfVlanEncryptKeyStatus.1.0.1 = 4

Getting the SNMP trap community string is not trivial. The reason for this is that anything which shows the configuration will have this field starred out. You can get to the value, but not in a report-like fashion. You can, however, search the archived configs under RME > Config Mgmt > Archive Mgmt > Search Archive. Assuming you know the SNMP trap receiver IP, you could search on:
snmp-server host x.x.x.x old-string
That would show you all devices that still had the old community string.
If you need to force RME to get the new config data, you can simply schedule a Sync Archive job under RME > Config Mgmt > Archive Mgmt > Sync Archive. Of course, if you made the changes outside of LMS, you will need to manually update DCR with the new community string.

SNMP Configuration question

I have a question.If i have a SNMP configuration in a switch 4510r, is there any posibility to reach the snmp server without the community command and without the server snmp command??????I have only this lines on the configuration.THANKSSS.
snmp-server engineID local 8000000903000025841E8C38
snmp-server trap-source Vlan10
snmp-server source-interface informs Vlan10
snmp-server packetsize 1024
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps syslog

If i have configured the communities and the server lines on the device, what could be the possible issue when the SNMP server reach the switch but the switch doesn´t respond to the request, and when i use the command #show snmp, we have an output in this way:THANKS FOR YOUR HELP
switch#show snmp
Chassis:
Contact: GISN Americas Network - tel: 978-858-7000
0 SNMP packets input
    0 Bad SNMP version errors
    0 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    0 Number of requested variables
    0 Number of altered variables
    0 Get-request PDUs
    0 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
145568 SNMP packets output
    0 Too big errors (Maximum packet size 1024)
    0 No such name errors
    0 Bad values errors
    0 General errors
    0 Response PDUs
    145568 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to 131.98.27.6.162, 0/10, 34282 sent, 0 dropped.
    Logging to 192.97.141.173.162, 0/10, 1721 sent, 0 dropped.
    Logging to 192.97.141.176.162, 0/10, 1721 sent, 0 dropped.
    Logging to 192.97.141.55.162, 0/10, 1721 sent, 0 dropped.

SNMP Configuration on solaris10

Please can anybody put some light on SNMP configuration on Solaris 10.I am newbie on this.I read SMA Agaent on solaris 10 is NET-SNMP compliant.I need to monitor disk usage,CPU load ..So I configured snmpd.conf (inside /etc/sma/snmp) for this.The traps I am getting are of series 1.3.6.1.4.1.8072.3.2.3.But I am not able to figure the MIB s which contains the description of these kind of traps.
Please help me.

Hi, I am on 12.1 weblogic, and I am stuck on where you set the SNMP Servername and port number.
We are on windows 2008, I see there is a services, SNMP .
Is there something I need to do on the weblogic side before i get into the SNMP agenets and traps, this part I understand, I am just unsure where to add the SNMP Servername and the user I wish the emails to go to.
I see in the security realms the user i can add to the group monitors.
-->, I am running WL 10.3 and SNMP works fine. The cluster generates traps based on particular mbeans, such as when a server's health state is not "OK", or when there are JDBC connection issues. You have to create a new SNMP agent within the admin server then build the individual traps ( String, Gauge, Counter, etc. ) and make sure you have a Trap Destination.

Sending snmp traps for SVM

i've got my box sending general traps, but i've noticed Sun Volume Manager requires separate configuration for this using /etc/snmp/conf/mdlogd.acl. How can i now verify that i will get traps if my internal drives (mirrored using meta commands) have issues or fail? is there a meta or md command i can issue as a check?
thanks

Hi Rolf,
Thanks for the information. It helped me.
I have configured the trigger event to use the track instead insted of the syslog. And it send the traps to the server.
sysUpTime.0 = 1805405563
snmpTrapOID.0 = cEventMgrMIB.0.2
ceemHistoryEventEntry.2.3 = 211
ceemHistoryEventEntry.3.3 = 0
ceemHistoryEventEntry.4.3 = 0
ceemHistoryEventEntry.5.3 = 0
ceemHistoryEventEntry.6.3 =
ceemHistoryEventEntry.7.3 = applet: TRACK_SNMP_TRAP
ceemHistoryEventEntry.9.3 = 0
ceemHistoryEventEntry.10.3 = 0
ceemHistoryEventEntry.11.3 = DOWN
Cheers!
Win

Snmp alerts for CPU utilization

Hi,
I want to enable snmp alerts on l2 and l3 switches to monitor CPU utilization.
I have Opmanager which is acting as SNMP server.
I have switches L2 and L3 which are running IOS 12.0, 12.1, 12.2
Do all these IOS versions support SNMP alerts?
And also I want to know the commands to be configured on switches for this.
Regards
skrao

You can configure SNMP traps for CPU Thresholding Notification.
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455772.html
You should be ok with the versions you list but check exact IOS version supports it at http://www.cisco.com/go/fn
If you do not want to use traps then there are specific oids that can be polled for 1minute average (1.3.6.1.4.1.9.2.1.57) and also 5 minute average (1.3.6.1.4.1.9.2.1.58). I've used these in the past with no problems. These oids may have been superceeded so check for latest. You can always snmpwalk a device to check oids.
The cisco SNMP navigator is helpful when it comes to oids.
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en
If you haven't got any SNMP configured yet on the switch check out http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddb4e54
HTH
--Phil

SNMP configuration in Ironport Cluster

Hi everyone,
I have 2 Ironport appliances X series in a cluster configuration, I want to configurate SNMP in both appliances but if I run the command snmpconfig it only allows me to configure snmp for the cluster, in this way I only can "ask" for status to 1 interface on behalf of the entire cluster and I dont know if a high cpu trap or high memory trap on the other appliance can be send to my snmp manager.
I tried to configure snmp in every machine (not cluster mode) but the appliance sends me an strange error and kick me out of the cli.
Anyone of you had configure snmp in a cluster environment? Can you guys tell me how can I do this?
Best Regards!

The term cluster is a misnomer. It is more of a centralize configuration. Both appliances will send traps individually and will share the same configurations. Basically both appliances act on their own, and don't share IP addresses or failover (the beauty of email is failover is built into MX records and transport configurations). There are instances when it makes sense to have separate configurations for a group of systems in the "Configuration Cluster". For SNMP this can be done at the Cluster or "Cluster Group" Level.
In my example I wanted to have a different SNMP Location for two sets of appliances:
What I had to do for SNMP, was to configure a Cluster Group for each location. This way I could say Appliance A & B are at location 1, and Appliances C & D are at location 2.So in the CLI, you will need to create the groups, and then assign your appliances to each group. Then Change your cluster mode in the CLI to the appropriate group and make the SNMP changes. Repeat for your other group.
Please let me know if this was helpful, I would be happy to go into more details.

SNMP Configure OnCommand System Manager 3.1 on FAS2020 Ontap 7.3.7

Hi, I have the to discover snmp after configure SNMP. Even I tried both trap hosts with my windows IP where I installed Oncommand system manager and the IP of Ontap 7.3.7. Can someone please verify which host is correct one? what is the requirement for SNMP configure. Thanks,Kevin.

Sorry, access for this KB is restricted. Then, check following point and fix them. 1. Check if SNMP agent is enabled.
   filer> options snmp.enable
   If not, enable it by "options snmp.enable on"
2. Check if SNMP access is allowed.
   filer> options snmp.access
   If IP address of System Manager host is not listed, set it by "options snmp.access host=<IP address>"
3. Check filer's SNMP community name.
   filer> snmp community
   By default, "ro public" is displayed.
   If you have modified SNMP community name, you need to modify registration on System Manager.
   Edit C:\Users\<username>\NetApp\SystemManager\SystemManager.config and adjust snmp-community
   element under storage-system element.

SNMP configuration for V480

Similar Messages

Maybe you are looking for