Snmp monitoring for wlc 4404

Hi,
we use a snmp monitoring software called Nagios in our LAN. Now we have two WLC 4404. Is it possible to monitor values via snmp? Is someone else doing it so?
Witch values can be monitored and for what values is it wise or practicable to monitor it?
Regards
Christian

There are some threads in this forum regarding this already. It is not as easy as monitoring a switch or router. the controllers combine the AP mac with the oid for unique lines. You can glean some snmp info off the controllers by using some of the generic OIDs and controller specific OIDs, but you will need an snmp monitoring program that you can load the WLC MIBs into and then tailor your monitoring of the controller based on that. I use Cacti, which is really awesome, but I would need to grab the complete OID off each controller based on the APs on it, which is fine as long as the AP is on that particular controller and not another one. snmpwalk is your friend in this case.
OID+mac = results

Similar Messages

  • Nagios SNMP Monitoring for NSS devices ?

    Has anyone managed to utilise the inbuilt SNMP functions of the NSS with nagios efficiently ?
    if so, what plugins are you using and how have you got them configured ?
    Steve

    There are some threads in this forum regarding this already. It is not as easy as monitoring a switch or router. the controllers combine the AP mac with the oid for unique lines. You can glean some snmp info off the controllers by using some of the generic OIDs and controller specific OIDs, but you will need an snmp monitoring program that you can load the WLC MIBs into and then tailor your monitoring of the controller based on that. I use Cacti, which is really awesome, but I would need to grab the complete OID off each controller based on the APs on it, which is fine as long as the AP is on that particular controller and not another one. snmpwalk is your friend in this case.
    OID+mac = results

  • SNMP monitoring for EoMPLS virtual circuit

    I am looking to implement SNMP-based monitoring of an MPLS layer-2 tunnel. The desired result would be the same as the output from the following command:
    "sh mpls l2transport vc"
    I have configured the router to generate SNMP traps based on LDP changes, but this is not specific to the status of the EoMPLS tunnel.
    Thanks in advance.

    Polling to these MIB values would have your task accomplished.
    1) VC status <--> cpwVcOperStatus
    2) If you need outbound staus <--> pwVcInboundOperStatus
    3) Inbound status <--> cpwVcOutboundOperStatus
    And here is the link for list of MIB objects for L2VPN.
    http://www.cisco.com/en/US/products/ps6441/products_configuration_guide_chapter09186a00808194e1.html
    HTH-Cheers,
    Swaroop

  • SNMP Monitoring for Sunone 5.2

    Hi,
    I want to monitor my LDAP boxes using SMARTs and IV. for this I need to setup SNMP on LDAP boxes. can someone give me hints to do this and provide mibs ?
    Regards,
    -Manish

    http://docs.sun.com/source/817-7607/monitor.html#wp19755
    http://docs.sun.com/source/817-7616/config.html#wp26382
    Do these help?

  • SNMP configuration in WLC

    hi all,
    Can any one tell me if there is document available for SNMP configuration for WLC 4404?

    http://www.cisco.com/en/US/docs/wireless/controller/7.0MR1/configuration/guide/cg_controller_setting.html#wpmkr1372608
    Configuring the device via snmp is very difficult and there really isn't a document covering that.  WCS uses snmp to configure the controllers.

  • What settings need to be set for the fastest roaming on my wlc 4404

    Hi all
    I notice that on my WLC 4404 when walking around with my laptop, I am dropping pings when it roams to another access point, Is there anything on the controller I need to check, and can I optimize these settings for roaming?
    cheers
    carl

    Hello Carl,
    to have romaing working fine you need to be sure of following:
    1) RF designed correctly , and enough overlapping is availble between the AP's.
    in addition for environment to be free from external noise..
    this can be confirmed with spectrum expert site survey
    2) what authentication and encryption used ( WEP , or WPA-PSK no need to check this point ->> skip :-) )
    if you are using any authentication like 802.1x ->> then enable CCKM on the WLAN to make more seamless roaming.
    3) if more than one WLC availble on site , configure mobility group between them,
    so if client roam from one AP in WLC 1 to AP on WLC 2 ->> no disocnnection observed....
    Kind regards
    Talal
    ===========
    please rate answers that you find useful , and mark as answered - when it is :-) - so others can find it easily

  • Recommended product for syslogging and snmp monitoring

    Hi,
        We currently use KIWI syslog but can anyone recommend a better product for syslogs from Firewalls, Routers and Switches. Our current product creates a seperate text file per day per device. Ideally I would like all these to be combined (or combinable for display purposes) into one log that shows to update realtime and have the ability to filterout "background noise" - stuff we know is acceptable, as well as being able to run simple or quick searches and reports. Ideally for asbout 200+ devices.
         Am I too hopeful or is there a product out there that can do this (that also will not break my companies bank account).
         Also, recommended products for SNMP monitoring if better than we currently use would be useful - currently using Orion and SNMPc.
    Regards
    Adrian

    Adrian,
    We use syslog-ng for RHEL. It can do what you need as far as writing to files and filtering out background noise, but it is not a search/reporting tool. If KIWI does the latter, I imagine you could tell it to read from the file that syslog-ng creates.
    It is open source for writing files through version 3.1.4. Later versions require licensing to write to files or if you are using a Windows OS.
    http://www.balabit.com/downloads/files/syslog-ng/open-source-edition/3.1.4
    Here are some other options:
    Rsyslog: http://www.rsyslog.com/
    Splunk: http://www.splunk.com/
    Snare: http://www.intersectalliance.com/projects/index.html
    Hope this helps.
    Steve Lee
    Emory University

  • How to configure SNMP agent for Oracle 10g

    Hello,
    I've installed oracle 10g in a Windows 2000 SP4 and I want to monitor database using SNMP.
    I've already installed Windows SNMP agent but I haven't any idea how to configure Oracle in order to grant SNMP monitoring.
    What should I do?
    Is Oracle database ready to be monitored via SNMP by default?
    Thanks in advance for your help.
    Regards,
    Carles

    Hello,
    Thanks for your message.
    In fact, I already found this doc in oracle, but it just show executables I have to install and my question can I install these executables.
    I've already installed Windows SNMP agent, configured and testedwith disk space checkings, but it doesn't work fine with Oracle.
    I launched Oracle Universal Installer and I checked Installed Products, but I haven't found how to install SNMP agents for oracle.
    How can I add Oracle Peer Master Agent and Encapsulator to my oracle installation?
    Thanks again for your help.
    Regards,
    Carles

  • WLC 4404 Wireless users getting disabled

    Currently Being Moderated
    Wireless users getting disabled
    Hi,
    I have WLC 4404 with 7.0.116.0 version. I was getting following messages for particular APs
    *Dec 20 14:11:13.875: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec 20 14:11:13.908: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Dec 20 14:11:29.383: %LWAPP-5-RLDP: RLDP stopped on slot 0.
    *Dec 20 14:11:29.674: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Dec 20 14:11:29.678: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec 20 14:11:29.700: %LWAPP-5-RLDP: RLDP started on slot 0.
    *Dec 20 14:11:29.707: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Dec 20 14:11:29.752: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Dec 20 14:11:29.757: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec 20 14:11:29.790: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Dec 20 14:11:45.396: %LWAPP-5-RLDP: RLDP stopped on slot 0. *Dec 20 14:11:13.875: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    After seeing one of the cisco forum, I have disabled RLDP for that particular APs
    so above messages are rectified.
    But right now we are not able to identify Rogue IP and it is not contained.
    So please give any suggetion so that i can rectify the above messages as well as i can identify the rogue IP.
    Thanks & Regards
    Gaurav Pandya

    Hi Scott,
    You are right i am not able to detect rogue APs because i disabled the RLDP. but when i enable the RLDP for that particular AP. i got the following messages with interface go up and down
    *Dec 20 14:11:13.875: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec 20 14:11:13.908: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Dec 20 14:11:29.383: %LWAPP-5-RLDP: RLDP stopped on slot 0.
    *Dec 20 14:11:29.674: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Dec 20 14:11:29.678: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec 20 14:11:29.700: %LWAPP-5-RLDP: RLDP started on slot 0.
    So please suggest me the mid way so that i can enable the RLDP (Detect the rogue APs) with out interface going up and down frequently.
    Regards
    Gaurav

  • Authentication for WLC

    Hi,
    I have a WLC (4404), and it is configured for authentication in ACS.
    When I conect in WLC whit browser (HTTPS), I put my username and password from ACS, and it works.
    However, if I put the local username in WLC it works.
    I would like to disable the username local when ACS works, as I do that?
    But when ACS go down a need of the local username...

    You will not be able to do this like how you can with a router or switch. Locally is checked first prior to tacacs and can't be changed. Maybe speak with you local Cisco wireless SE to see if he can put that as a feature enhancement.

  • Oracle VM 3.0 and HP Hardware SNMP monitoring

    Has anyone successfully installed a SNMP tool to monitor Hard disk status in an HP Proliant server that has OVM 3.x server running on it? Insight Manager seems to require too many RPMs that we can not install and we are playing with ZenOss but it too does not seem to detect the hard disks. Though at the moment, I have CPU, Power Supplies and memory being monitored. Just not the internal RAID set that receives the OVM Server software.
    This must be possible.

    Avi Miller wrote:
    If you have Oracle VM Support, you can download the net-snmp RPMs for Oracle VM 3.0 from My Oracle Support.Yes i have done that and installed them as well as all of the other rpms needed. Once that was done and configured Zenoss shows me
    Network Routes
    Memory Modules
    Power Supplies
    Interfaces
    Fans
    Temperature Sensors
    FileSystems
    IP Services
    Processors
    but not
    Expansion Cards
    Hard Disks
    Logical Disks
    I have these other 3 on other servers, so it must be an agent needs to be started or configured that isn't there. In this case Zenoss might not be the correct solution but I am wondering what others have done to solve this type of issue. We need hard disk monitoring as its vital to knowing if one disk goes bad in the RAID01 array so we can change it out before the other one fails.
    Not comfortable of going to production without this monitoring.
    Edited by: user897654321 on Feb 23, 2012 2:01 PM

  • Basic Network Monitoring for Cisco Operation Manager 2012

    Hello,
    Please bear with me as i'm new the Operations Manager 2012 world. I've just installed operations manager 2012 in our environment and i've setup a network management point. I've discovered my networking gear which is primarily cisco equipment. The devices
    are appearing as CERTIFIED. It appears that they are HEALTHY however in most cases i'm getting some arbitrary monitors. I have a 6509 switch where memory and processor appear to be being monitored out of the box. I'm receiving alerts and everything.
    My question is how do I turn on monitoring for other discovered components. I seem to understand I can make SNMP monitors under the authoring pane if i know the OID. That sounds like it'd be tedious work for such a simple and basic monitor. However I was
    under the impression I would be able to monitor a lot of these components with a simple click of a button. Is this not the case? I'm primarily interested in monitoring the state and performance of particular interfaces as well as the state of the power supplies
    in our switches. Is there a guide that explains the basic principles of this. What are my options?
    Thanks!
    -Brandon

    Hi,
    You will need to edit the discovery and broaden the range. You may use recursive discovery.
    Recursive discovery will try to discover any other network devices it knows about through its Address Routing Protocol (ARP) table, its IP address table, or the topology Management Information Block (MIB) to grow the network map and present all applicable
    devices to you for monitoring.
    You can also filter out devices that you don't want to be discovered by using properties such as the device type, name, and object identifier (OID). This is a handy option if you wanted to quickly discover all the network devices in your network except,
    a small number or some with a specific criteria.
    In really large networks with a lot of network devices, keep in mind that there is a default limit of 1500 network devices that can be discovered recursively. You can of course tweak this limit to suit your environment if you wish, but for most people, this
    won't be needed.
    More details, please go through the article below:
    http://kevingreeneitblog.blogspot.com/2012/07/scom-2012-network-monitoring-explicit.html
    Regards,
    Yan Li
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • WLC 4404 %OSAPI-3-FILE_OPEN_FAILED

    the WLC 4404 present this logs:
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/927/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'gccp_t'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/926/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'dot1dTimer'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/925/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'dot1dRecv'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/921/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'fdbTask'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/920/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'nPCSL_timer'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/916/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'tFrameReceive'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/913/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'tFrameReceive'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/917/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'tFrameSend'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'Gmac Link Task'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/905/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'tDapiTxTask'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/904/stat.(erno 24)
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED:  osapi_task.c:3431 Failed to retrieve statistics  (/proc/<pid>/stats) for task 'RMONTask'
    *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED:  osapi_file.c:370 Failed to open the file : /proc/903/stat.(erno 24)
    when present this loggs the device present those symptoms:
    lost GUI session
    Lost console conection
    Lost SSH and Telnet conecction
    the WLC 4404 not work is stopedd

    Almost looks like it could be defect ID CSCtx02515.  SHows that it's fixed in 7.2.110.0, but if you have a 4404, you can't run 7.2 code.
    Symptom:
    High CPU on webJavaTask
    Alternatively: large number of TCP connections, leading to file descriptor problems like:
    osapi_file.c:370 Failed to open the file : /proc/1054/stat.(erno 24)
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtx02515
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • SNMP monitoring of Oracle 10g?

    Hi there,
    I'm curious about using SNMP technology to monitor Oracle 10g databases.
    I've done some light reading on the subject and I'm now at the stage
    where I have a few questions.
    -What exactly do I need to configure in my Oracle 10g environment?
    -Is Enterprise Manager the best and/or only UI available for me
    to carry out configuration chores?
    -I see no SNMP specific documentation for 10g; why is that?
    -I do see a good document for 9i:
    Oracle SNMP Support Reference Guide Release 9.2.0 Part Number A96672-01
    http://download-west.oracle.com/docs/cd/B10501_01/em.920/a96672/toc.htm
    Is the above document suitable for configuring SNMP monitoring of Oracle
    in a 10g environment?
    -moi

    I'm able to set up traps via the EM website following these instructions:
    http://download-west.oracle.com/docs/cd/B19306_01/em.102/b40002/notification.htm
    However, what I'm really looking for is the ability to do snmp gets. I need functionality similar to how the old school DBSNMP under OMS used to work. These commands seem to be totally missing. I found the following documentation:
    http://download-east.oracle.com/docs/cd/B19306_01/em.102/b16244/chap2.htm#sthref74
    Which indicates there should be an snmp subfolder under $ORACLE_HOME/sysman, but that folder does not exist in my installation. I installed Oracle EE. Is there another package I need to install in order to make the subagent run like a normal snmp agent?
    So far if I do a:
    emctl start dbconsole
    that starts up the EM Website and I can use that no probelm. If I...
    emctl start agent -- I get:
    Starting agent ... started.
    issuing a 'emctl staus agent' gives me a normal status message. Things start to get strange when I try to start the subagent, which to my understanding is what I need running in order to to talk to net-snmp, which is the master agent running on this host. Here's what happens:
    [zaro@cheetah bin]$ ./emctl start subagent
    Oracle Enterprise Manager 10g Database Control Release 10.2.0.1.0
    Copyright (c) 1996, 2005 Oracle Corporation. All rights reserved.
    Starting sub agent .....started
    [zaro@cheetah bin]$ ./emctl status subagent
    Oracle Enterprise Manager 10g Database Control Release 10.2.0.1.0
    Copyright (c) 1996, 2005 Oracle Corporation. All rights reserved.
    Sub agent is not running..
    I guess my question is how do I get to have the ability I used to have back in 8i to start up dbsnmp and then have my SNMP monitoring app "discover" the agent and use its instrumentation to get data?

  • Emergency Version for WLC 5508 with 6.0.188

    The release notes for 6.0.188 talks abt 5.2.157.0 ER.aes. But 5508 does not like the file AIR-WLC4400-K9-5-2-157-0-ER.aes.
    How can I get the boot loader on WLC 5508?
    On WLC 5508...
    Product Version.................................. 6.0.188.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    On WLC 4404
    Product Version.................................. 6.0.188.0
    RTOS Version..................................... 6.0.188.0
    Bootloader Version............................... 4.2.205.0
    Emergency Image Version.......................... N/A  ----------> Even though I installed 5-2-157-0-ER.aes it does not show here... Bug???

    Ok. In the release notes of 6.0.188 they should have seperated for 5508.
    On WLC 4404
    Product Version.................................. 6.0.188.0
    RTOS Version..................................... 6.0.188.0
    Bootloader Version............................... 4.2.205.0
    Emergency Image Version.......................... N/A
    When u say "The n/a issue is a bug but its with the primary image, not the ER image"
    Do you mean that because my primary image is 6.0.188 which has bug to not take  or show the ER image?

Maybe you are looking for