SNMP OID for wireless client

Dear Netpro Community,
I would like to know whether the following OID talks about the number wireless clients joining the AP at which OSI layer.
Rgrds,
Beno

Sry, the oid information is here:
Object cDot11ActiveWirelessClients
OID 1.3.6.1.4.1.9.9.273.1.1.2.1.1
Type Gauge32
Permission read-only
Status current
Units Device
Range 0 - 2007

Similar Messages

  • Initial configuration of ACS 5.1 for EAP authentication for Wireless clients

    Hi,
    I have set-up with below devices :
    Wireless LAN controller 5508
    LAP 3302i
    and ACS 5.1
    since i am new in ACS 5.1 configuration , I need so information to go ahead to configure ACS 5.1.
    which EAP method to use for wireless client authentication ? what is the best practice ?
    I have gone through some cisco documents and it shows that best practice is to configure PEAP but for the same , I need to install certificate in ACS server as well in client PC. is that so ?
    I have no clear picture for this certificate ?
    from where i can get this certificate or do i need to purchase this certificate separately from cisco. how to install it in ACS server ?
    I will be obliged to get atleast initial configuration for ACS 5.1 to enable the EAP method,
    I need GUI based initial configuration for ACS 5.1
    This mentioned ACS 5.1 is installed on ACS 1121 hardware appliance.

    Hi,
    which EAP method to use for wireless client authentication ? what is the best practice ?
    -> I would advise the most widely spread EAP method, which has the best ratio security/easy to deploy: PEAP with MSCHAPv2, which is available by default by all windows machines.
    I  have gone through some cisco documents and it shows that best practice  is to configure PEAP but for the same , I need to install certificate in  ACS server as well in client PC. is that so ?
    -> You will always need to install a server certificate, however, there is no need for client certificate because the authentication is based on the MSCHAP credentials exchange, not certificate based. The only requirement on the client regarding certificates is the following.
    If you want to validate the server certificate, you have to install the server certificate under the trusted CAs of the clients.
    If you do not require to trust the server certificate, you can simply disable the option of server certificate validation.
    I have no clear picture for this certificate ?
    from  where i can get this certificate or do i need to purchase this  certificate separately from cisco. how to install it in ACS server ?
    -> The server certificate can be a simple self signed certificate that you generate and install on the ACS GUI.
    Please feel free to follow this step-by-step guide on
    PEAP under Unified Wireless Networks with ACS 5.1 and Windows 2003 Server:
    http://www.cisco.com/en/US/partner/products/ps10315/products_configuration_example09186a0080b4cdb9.shtml or in pdf
    http://www.cisco.com/image/gif/paws/112175/acs51-peap-deployment-00.pdf.
    HTH,
    Tiago
    If  this helps you and/or answers your question please mark the question as  "answered" and/or rate it, so other users can easily find it.

  • Snmp oids for the command "show counters interface intx/y delta"

    Hello,
    I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
    Is possible to get these values using SNMP??
    Thank you
    Roman

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • SNMP OIDs for solaris 8

    Hello
    Someone could tell me where to find a list of SNMP OIDs for solaris 8
    thank you for your cooperation

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • SG-500 - SNMP OID for CPU Load?

    Hello,
    i have several SG500 (Standalone and stacked). How can i get the CPU Load via SNMP? Who knows the correct SNMP OID for CPU Load?
    In the MIB which are provided as download a wasn't able to find the correct OID.

    Hello,
    There are three OIDs available for CPU usage:
    CPU utilization for 5 seconds
    .1.3.6.1.4.1.9.6.1.101.1.7.0
    CPU utilization for 1 minutes
    .1.3.6.1.4.1.9.6.1.101.1.8.0
    CPU utilization for 5 minutes
    .1.3.6.1.4.1.9.6.1.101.1.9.0
    This came from a scrap note I had in an e-mail, so I am not exactly sure where this information is originally.
    Let me know if that works for you,
    Christopher Ebert - Network Support Engineer
    Cisco Small Business Support Center
    *please rate helpful posts*

  • Network printers drop for wireless clients

    I am having a serious problem with my Airport N. My Epson CF11NF (a laser all-in-one which is connected via ethernet to the Airport) is continuously disappearing for wireless clients. All the wired machines can see and print fine, but the printer becomes invisible for wireless clients. The problem is resolved by unplugging and plugging back in the Airport, but I am having to do this more than once a day, which is not acceptable.
    Has anyone experienced this problem? Any advice on what is going on? Should I return the Airport? The wireless clients are all running OSX 10.5.1. The wired clients are all running OSX 10.4. Could this be the issue?

    Others are having similar issues and symptoms, however, I've seen no solutions yet. My Airport Extreme disappears also but access to the internet is unaffected. I can also still access my iMac from my MacBook (iMac still shows up in Finder as a shared volume), however, once the AEBS drops from view I can no longer access printers on the network. (One connected to a networked PC and the other connected to the AEBS.) Both Macs are running Leopard.
    Anyway here's a link that others are using to discuss these issues. Good Luck. http://discussions.apple.com/thread.jspa?threadID=1197872

  • Wireless 3850 and Web-Auth for Wireless clients

    Hi
    I can't get the web-auth feature to work properly on the Catalyst 3850 for wireless clients.
    Internet is all tested and there is full IP connectivity.
    Issue is when I enable the webauth feature on the SSID. Incidentally when I enable the SSID to use consent it works.
    I am using local authentication for the guest users.
    When user logs onto the wireless, they get to the landing page, and are able to enter the credentials then there is a 30 second pause. The client detail says WEBAUTH_PEND and then a pop up window comes back as seen below
    Config below
    interface Vlan302
    description **** Wireless Guest ****
    ip address 10.145.224.161 255.255.255.224
    ip helper-address 10.144.214.134
    ip helper-address 172.17.2.56
    ip http server
    ip http secure server
    ip dhcp snooping
    wlan XXXXX 2 XXXXXX
    aaa-override
    accounting-list default
    client vlan 302
    ip flow monitor wireless-avc-basic input
    ip flow monitor wireless-avc-basic output
    no security wpa
    no security wpa akm dot1x
    no security wpa wpa2
    no security wpa wpa2 ciphers aes
    security dot1x authentication-list WEB_AUTH
    security ft
    security web-auth
    security web-auth authentication-list WEB_AUTH
    security web-auth parameter-map vit_web
    no shutdown
    parameter-map type webauth vit_web
    type webauth
    security web-auth parameter-map vit_web
    user-name Guest1
    creation-time 1390837878
    privilege 15
    password 7 022D0156060F1B351D
    type network-user description Temp-Guest-User guest-user lifetime year 0 month 1 day 0 hour 0 minute 0 second 0
    user-name Guest2
    creation-time 1390838016
    privilege 15
    password 7 0724244143000D1145
    type network-user description Temp-Guest-User guest-user lifetime year 0 month 1 day 0 hour 0 minute 0 second 0
    aaa new-model
    aaa authentication login WEB_AUTH local
    aaa authorization network WEB_AUTH local

    Hey Greg,
    Did you also define the global webauth parameter? I think I had to do this to get my 5760 "working" or as working as these new controllers can be.
    parameter-map type webauth global
    type webauth
    virtual-ip ipv4 x.x.x.x wlc.whatever.org
    max-http-conns 50
    Also I had to enable http server in addition to secure server
    ip http server
    ip http secure-server
    Are you using a self signed cert?
    I saw windows clients take a long time to load the page when using a self signed cert.
    MAC clients dont seem to work if you use the IOS or OSX based logon. You'll need to disable the auto logon and launch a browser for the redirect. There was a bug ID around this MAC problem which was supposedly resolved in 3.3.1SE  but I still have the problem.
    -Kyle

  • Bridge does not work for wireless clients - connecting to existing network.

    Hi - I really hope somebody can help out here, after hours of trial & error, I have finally given up
    I need to connect my Airport Extreme Base Station to my existing network. I have a linksys router (192.168.15.1) connected to my modem and this linksys router acts as DHCP server too.
    I suppose I have to use "bridge mode" for that to work. But should the linksys be connected to the AEBS using the AEBS's WAN or LAN port?
    If I use "bridge mode", then wired computers to the AEBS works fine - getting an IP from the linksys etc. BUT, the wireless clients will have a self-assigned IP and not get through to the internet. It's like the AEBS will not allow wireless clients to "get through" unless AEBS itself is handing out IP addresses.
    Page 36 of this manual ( http://manuals.info.apple.com/en/DesigningAirPort_Networks10.5-Windows.pdf ) shows the setup I want. But in the picture, it says "Ethernet WAN port" but the text says: "The Apple wireless device (in this example, a Time Capsule) uses your Ethernet network to communicate with the Internet through the Ethernet LAN port ( <--> )." I don't know which one to use, WAN or LAN - they show WAN but say LAN?
    When I set it up as "share an IP address", the AEBS status tells me "double nat" and to change from "shared IP" to "bridge mode". I do that, and everything seems fine - for the wired clients. Now the wireless clients cannot connect, Airport on the MacBook Pro just say "Connection failed" and the MacBook says "Invalid password" (translated from danish), even though I set the Airport Utlity to save the password in keyring, so it should be correct... If I disable wireless encryption, the wireless clients will connect but get a self-assigned IP, and therefor not work (cannot get online)...
    It seems the only way I can get wireless to work, is if I set AEBS up as DHCP, but then it won't be on the "same network" as the linksys (192.168.15.1), but rather on 10.0.x.x as I select. If I select 192.168.x.x within AEBS, I'm also getting some error messages, conflict/subnet thing.
    Anyway - I really hope somebody knows how to get wireless clients to get an IP address from existing ethernet when connected to the AEBS.
    Thanks!!

    I've given up and had to go back to running "Double NAT" which also reports as a "problem" within the AEBS, but I just "ignore" it so the light will always be green.
    It still ***** though, as "Double NAT" is also a reason for "Back to my Mac" not working properly, but how the ** am I supposed to avoid Double NAT when the wireless will not work in bridged mode?!

  • Can router dhcp different addresses to different vlans for wireless clients

    is it possible for the router to hand out different ip's to wireless clients on different vlans?

    Yes, the router needs to have a dhcp pool on each subnet and have an "interface Vlan x" for each vlan. It will then assign ips to clients in different vlans.
    One vlan per SSID.

  • WRT54GX2 Wireless Security Enabled DHCP blocked for wireless clients

    Hey gang,
    My subject says it all.  Yesterday  I updated my WRT54GX2 version 1's firmware to the latest and greatest.I first reset the box, and rebooted. I updated the firmware. On the first attempt I picked the wrong image file. The machine halted and told me bad image. I then found and installed the correct image. I then added an Admin password, and entered a new SSID. I left the DHCP settings at the default. I then set wireless security at WPA Personl/WPA2 with TKIP&AES.
    I found the wired client could obtain an IP address and to connect to the internet. The wireless clients could connect, but could not obtain an IP address.
    I left the wireless security settings off.
    Any suggestions?

    The wireless security settings are correct. The wireless clients "CONNECT" to the WRT54GX2. The clients stall on obtaining an IP address via DHCP. Fixing the clients with static IP addresses also does not work.
    I repeat: The wireless clients successfully connect to the WRT54GX2. The WPA/WPA2 & TKIP/AES settings are correct. The clients cannot receive a dynamic IP address.
    On Friday I will reset the box for 30+ seconds. I doubt this will have any effect. I reset it on Tuesday twice on Tuesday, and still have the problem.
    Any help appreciated.
    -WJ

  • WLC 4400 series OID for Current Clients

    Can someone advise what is the OID for the number of current clients for the WLC 4400 series appliance.
    Thanks.

    Based on the results of your walk, I would say it's reports all of the instances on that particular controller...and I say this because only one instance is reported. I would think that if you have multiple WLANS on that WLC, you would get multiple instances reported back, so, (maybe, like you) I'm confused by the description in the MIB object where it states:
    "No of Mobile Stations currently associated with the WLAN."
    which to me looks like "the WLAN" is used in the singular.
    At this point, I think the best thing to do would be to open a TAC case with all of this info, and we can get with our developers for confirmation.
    Hope this has been somewhat helpful, and please rate these posts.
    Thanks,
    -Joe

  • Reading SNMP OID for used storage on px12-400r

    Hi, does anyone know how get the correct value for used disk space via snmp on the px12-400r nas?
    All capacity is configured as one big cifs share. I want to monitor the usage of space with snmp.
    If I do a snmpwalk (v3) I can pinout the filesystem /mnt/pools/A/A0 on OID 1.3.6.1.2.1.25.2.3.1.3.38.
    If I read the oid for StorageUsed I get a strange negative value: -1084997477
    This value changes while data are written to the cifs share so it seems to be monitoring. But what to do with this negative value?
    Thanks for any help!
    /Anders

    Hello anders-px12-400
    I recommend checking with rtrevino from his thread.   The unit's are different, but the firmware is bascially the same across all Lifeline devices
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • SNMP OID for DHCP on Server 2012

    We recently installed Server 2012 standard on one of our servers and were trying to keep a graph of DHCP lease use. Anyway the OIDs for DHCP in Server 2008 R2 started with "1.3.6.1.4.1.311.1.3.2.1.1". If I try to snmpwalk these same OIDs on the new Server
    2012 (We the DHCP server configured and active), I get:
    Error in packet.
    Reason: (genError) A general failure occured
    Failed object: SNMPv2-SMI::enterprises.311.1.3.2.1.1
    I'm using SNMPwalk and I've never had a problem with this before. Any idea what would cause this? Thanks!
    Thanks!

    I'm having the same issue. OIDs just don't work against a 2012 DHCP server. I can snmpwalk other OIDs, just not DHCP :(
    Firewall has been disabled (and there were already adequate snmp rules allowing the traffic). Since I can query other OIDs, I'm ruling out firewall.
    Has this info been removed in 2012?

  • What are steps configure Certificate based authentication for Wireless clients with ACS 5.3?

    I need to autheticate my clients connecting via wireless.
    clients have user certificate installed on them, i need help configuring the ACS to do the authentication.
    can some one please help me with the steps.
    Thanks

    Two primary steps
    - define the trust certificates needed to verify the clients user certificates
    Users and Identity Stores > Certificate Authorities
    - change result of identity policy to select a certificate authorization profile. If have the defautl config
    Access Policies > Access Services > Default Network Access > Identity
    by default can select the "CN Username" as a result

  • SNMP OID for 5108 Chassis input and output Watts?

    Anybody know these?
    Craig

    Craig,
    OID for cucsEquipmentChassisStatsTable --  1.3.6.1.4.1.9.9.719.1.15.10
    UCS MIBs are available here
    ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html
    HTH
    Padma

Maybe you are looking for