Snmp oids for the command "show counters interface intx/y delta"

Hello,
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
Is possible to get these values using SNMP??
Thank you
Roman

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

Similar Messages

Change in privilege level for the command show logging

I have recently discovered a change in behavior in IOS. The command show logging has traditionally been available at user level. Now it has become a privilege level 15 command.
I thought that this was strange and opened a case with Cisco TAC about it. I was told that this is a new "feature" that was implemented for bugid CSCsl61281. Unfortunately this bugid is viewable by Cisco internally but not viewable by the public.
The TAC engineer tells me that this change is integrated into these releases:
This was integrated into the following releases:
12.4(24.05.01)PIX11
12.4(21.14.09)PIC01
12.4(19.03)T
12.2(52.23)SIN
12.2(33)SXI01
12.2(32.08.11)SX229
12.2(32.08.11)SR174
I do not think that this is a good change. If you do not think that this is a good change I suggest that you contact your Cisco support team and express your opinion about this change.
Otherwise as you go to new versions of IOS be aware of the potential impact on your network monitoring processes and procedures that show logging will require level 15 privilege access.
HTH
Rick

Hi Rick,
Can you suggest me references to know more about privilege level commands?
How to enable different commands for different levels of privileges?
Thanks.
-Sudhish

SNMP OIDs for ASR1k

Hi everyone,
We're trying to read CPU & MEM values from ASR1006 equipment. Obviously the old OIDs are not supported on this platform. This is what we have found by going through the snmp object navigator. (I assume .2 is the ESP, .3 is the RP, .4 & .5 are the SIPs). But the values we get from the command line are slightly different than what we get through snmp. Has anyone done this before? What OIDs do you use?
=====================================================================
CPU:
1min: cpmCPULoadAvg1min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.5; Value (Gauge):
5min: cpmCPULoadAvg5min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.5; Value (Gauge):
15min: cpmCPULoadAvg15min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.5; Value (Gauge):
======================================================================
Memory:
cpmCPUMemoryUsed
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.5; Value (Gauge): KiloByte
cpmCPUMemoryFree
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.5; Value (Gauge): KiloByte
Best Regards,
Babak

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

SNMP OIDs for solaris 8

Hello
Someone could tell me where to find a list of SNMP OIDs for solaris 8
thank you for your cooperation

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

Cat6509 - SNMP OIDs for interface stats

Hello,
I have a Catalyst 6509-E-VSS with IOS 12.2(33)SXI3.
I'm looking for OIDs to retrieve the same counters I get with the commands
"show interface stats" and "show interface switching".
I want to graph the number of packets that are process switched.
The OIDs from IF-MIB ( ifInOctets, ...) show only the total number of octets not the
switching path.
Thanks for help
Mike

After a long time silence on this frontier the problem is comming up again.
My goal is still to find out, what interface causes process switched traffic.
There is usualy a lot of traffic handled in software but sometimes (of course on weekend midnight) it seems to increase the cpu load (IP Input process).
Regarding the Cisco document "Troubleshooting High CPU Utilization Due to the IP Input Process" I want to monitor traffic by switching path.
So again - does anybody has an idea to get these counters with snmp ?
Update: IOS is now 12.2(33)SXJ3

What is the default key command for the COMMAND key?I seem to have changed it somehow along the way and now when I push the command key it hides all windows or shows desk top I need to correct this as soon as possible-.any ideas?

What is the default key command for THE COMMAND (apple) key? I seem to have changed it somehow along the way and now when I push the command key (only) it hides all open windows and shows the desk top and when I push it again it shows all windows again...I need to return to default A.S.A.P. just this one key...Any ideas? Thanks in advance...

Go to
 > System Preferences > Keyboard
Click on the 'Keyboard' tab and hit the 'modifier keys...' button. You can see and change the defaults there.
As I'm not sure if all the labels are the same in Lion, he's a screenshot from Snow Leopard. It should be similar enough:

Need the Cisco ASA5520 SYS OID for the LLDP protocol

Hi :
I need the Cisco ASA5520 SYS OID for the LLDP protocol so that I can create the network connection between Cisco ASA5520 and the 3rd party networking device in this 3rd party network management management system.
Can anyone help on this?
I tried to search the web and got some LLDP MIB files but they all cannot solve the problem. What I think and I need to have now is the SYS OID number for this Cisco ASA5520.
I know that the SYS OID for ASA5520 is 1.3.6.1.4.1.9.1.670. Now I need is the SYS OID for its LLDP protocol. Can someone help on this?
Many thanks!
tangsuan

Hi Afroj Ahmad:
I think it is not due with command line. It is the lack of OID information for Cisco ASA5520 to be able discovered by 3rd party Network Management System.
If I am not wrong, the ASA5520 should have been configured correctly for providing SNMP to the 3rd party network management system (NMS) and as such, the NMS is then able to capture the the SYS OID for ASA5520 is 1.3.6.1.4.1.9.1.670 from the ASA5520.
The SNMP configuration is as below:
snmp-server host inside 172.16.0.82 community public version 2c
snmp-server host inside 172.16.8.50 community public version 2c
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
snmp-server enable traps ipsec start stop
snmp-server enable traps entity config-change fru-insert fru-remove
snmp-server enable traps remote-access session-threshold-exceeded
The 3rd party NMS can capture the product OID from ASA5520 after given the ASA IP address to the NMS. It is the LLDP OID that is not included in the product OID to cause the 3rd NMS cannot link up the LAN connction between the ASA and the 3rd party switch. There is no LLDP configuration in ASA command. I believe the LLDP should be provide externally either by key in manually or upload the MIB file to the 3rd party NMS. I have tried also uploading few MIB files but all not succesfully done.
I think the direct method is just key in the LLDP OID inside the 3rd party NMS system so that the 3rd NMS can embed the LLDP information into its operation kernel then the NMS can link up the LAN connection between the Cisco ASA and its switch.
Many thanks!
tangsuan

SG-500 - SNMP OID for CPU Load?

Hello,
i have several SG500 (Standalone and stacked). How can i get the CPU Load via SNMP? Who knows the correct SNMP OID for CPU Load?
In the MIB which are provided as download a wasn't able to find the correct OID.

Hello,
There are three OIDs available for CPU usage:
CPU utilization for 5 seconds
.1.3.6.1.4.1.9.6.1.101.1.7.0
CPU utilization for 1 minutes
.1.3.6.1.4.1.9.6.1.101.1.8.0
CPU utilization for 5 minutes
.1.3.6.1.4.1.9.6.1.101.1.9.0
This came from a scrap note I had in an e-mail, so I am not exactly sure where this information is originally.
Let me know if that works for you,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts*

SNMP OID for Stuck CICs

Hello,
We have a PGW2200 and we are facing a stuck CIC problem. Im trying to monitorate it thru zabbix but I cant find the correct OID for the information. DOes anyone knows it, or can point me some document where I can find the OID ? I googled in many ways but for some reason I couldnt find the information.
Best Regards.
Luis Fernando Laimer

When I use the command:
rtrv-tc: it returns as follows:
CIC=1,PST=IS,CALL=IN,BLK=NONE"
CIC=2,PST=IS,CALL=IDLE,BLK=NONE"
CIC=3,PST=IS,CALL=OUT,BLK=NONE"
CIC=4,PST=IS,CALL=IDLE,BLK=NONE"
CIC=5,PST=IS,CALL=IDLE,BLK=NONE"
CIC=6,PST=IS,CALL=IDLE,BLK=NONE"
CIC=7,PST=IS,CALL=IN,BLK=MATE_UNAVAIL"
CIC=8,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=9,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=10,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=11,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=12,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=13,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=14,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=15,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=16,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=17,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=18,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
Those identified by BLK=MATE_UNAVAIL wont work.
I guess its an issue of our service provider, but for now I need to monitore the occorence of this situation.
Best Regards

Using a Variable in SSIS - Error - "Command text was not set for the command object.".

Hi All,
I am using a OLE DB Source in my dataflow component and want to select SQL Query from the master table I have created variables v_Archivequery
String packageLevel (to store the query).
<Variable Name="V_Archivequery" DataType="String">
     SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
     FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
     ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
     Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)
    </Variable>
I am assigning this query to the v_Archivequery variable, "SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)"
Now in the OLE Db source, I have selected as Sql Command from Variable, and I am getting the variable, v_Archivequery .
But when I am generating the package and when running I am getting bewlo errror
Error at Data Flow Task [OLE DB Source [1]]: An OLE DB error has occurred. Error code: 0x80040E0C.
An OLE DB record is available. Source: "Microsoft SQL Native Client" Hresult: 0x80040E0C Description: "Command text was not set for the command object.".
Can Someone guide me whr am going wrong?
Please let me know where am going wrong?
Thanks in advance.
Thankx & regards, Vipin jha MCP

What happens if you hit Preview button in OLE DB Source Editor? Also you can use the same query by selecting SQL Command option and test.
Could you try set the Delay Validation = True at Package and re-run ?
If set the query in variable expression (not in value), then Set Evaluate As Expression = True.
-Vaibhav Chaudhari

I get no audio for the Daily Show and Colbert Report

I am using the most recent Adobe Flash Player 11.4.402.265 with Windows 7, 64-bit, which works for all videos except those for The Daily Show and the Colbert Report, which have no audio.
The Daily Show and Colbert Report play in Google Chrome, but not in Firefox.

Sometimes it's jest THEM! But be sure to check PLUGINS. The Shockwave and Java applications may need 'PLUGIN UPDATE' for newer versions. Suggest a check for any outdated PLUGIN UPDATE found from the Mozilla Firefox Toolbar 'Help' Menu > 'Firefox Help' > [lower right margin displays link to more info to review and 'UPDATE PLUGIN's!

I am putting together a slide show using iphoto and I wanted to add a description on each slide/photo. How can I do that? Also on the choice of music for the silde show, if the slide show is longer than one song can you chose a different song for backgrou

I am putting together a slide show using iphoto and I wanted to add a description on each slide/photo. How can I do that? Also on the choice of music for the silde show, if the slide show is longer than one song can you chose a different song for background music?

This might help
http://www.apple.com/findouthow/photos/#slideshow
Regards
TD

Software needed for the USB device, "USB Interface Controller TEST2.0"

My mother recently acquired a digital camera. She acquired it from a second-hand store, which did not include an interface cable or software. The manual (and the USB port on the camera) indicates that a male-male USB cable is necessary for photos to be copied to the hard drive.
I was not successful in locating such a cable at any local electronics store (I assume such a cable is now out-of-date). I purchased one from a seller on eBay. The brand is "e circuit electronics".
Upon powering up the camera with the cable connected to it and the computer, the following message appeared:
"Software needed for the USB device "USB Interface Controller TEST2.0" is not available. Would you like to look for the software on the Internet?"
I clicked "Yes". After an approximate two-minute wait, another message appeared stating:
"Software Update is not able to connect to the Internet. Please check your configuration and try again."
I deleted, "Software Update Preferences" in the Preferences folder inside the System Folder, without solving the problem. How do I solve the issue of allowing Software Update to connect to the Internet?

Thank you for your continued assistance, BDAqua. Unfortunately, the driver you linked to does not seem to be compatible with the camera. It is a driver for the V20 model, whereas my model would correspond to be a V2755, as referenced from a list of other Vivicam models when during a search at the Open Drivers web site.
From the system requirement about the card reader you gave me, it will not work, as this system is running 9.1. I am hesistant to upgrade this computer to 9.2, as I have experienced system unstability with that version, with even the 9.2.2 update applied.
In the mean time, I have e-mailed Vivitar regarding this issue, but have as of yet received a reply.
I am not certain as to other specifics to give you, in order to solve the Software Update problem. Please elaborate.
Yes eww, the computer in question is able to fully connect to the Internet for all that I need. I am fully aware of the difference between a computer connecting to the Internet, and a computer connecting to a digital camera. I have 15 years of Macintosh experience.

Privilege level for the commands

Hi All,
I am trying to modify the privilege level of the commands in my router.
I need to understand what is the privilege level for the commands.
Is there a command in the IOS or a link with a document on the CCO with the criteria or the list of the command and its corresponded privile level.
Thanks
Matteo

Matteo
I am not clear what it is that you are trying to do. But let me make a suggestion. While there are 16 privilege levels (0 through 15) there are two levels that are commonly used 1 and 15. 1 is what is usually called user mode and is the default level when someone first logs into the router. My suggestion is to identify what group of commands you do not want to be available in user mode, decide if they should be available in something less than 15, pick a level, and assign the commands to that level.
If you really do want to start from a list of commands and their privilege level, I do not think that you will find any single source which will accurately give you the privilege level for all commands. The closest you will find is to look in the command reference and find the command. The command reference will usually describe the privilege level. Unfortunately I have found a few situations where the description of privilege level was not correct.
My advice is that if you want to find the privilege level for some commands that you want to manipulate, that you get a router and try the command and determine what its privilege level is.
HTH
Rick

Is there (or can I create) a keyboard shortcut for the command "export"?

is there (or can I create) a keyboard shortcut for the command "export"?

Keyboard Shortcuts are created in the System Preferences app, Hardware section, Keyboard, Keyboard Shortcuts tab.
Select Application Shortcuts on the left.
Click the "+" sign on the right and in the dialog box that pops up, enter: "Export..." and your preferred key combination. Here's an example:
Keep in mind that when you enter the name of the action in a layered menu, such as File > Export..., or Share > Export..., you are only going to enter the last menu choice, not the higher levels.
Regards,
Jerry

Snmp oids for the command "show counters interface intx/y delta"

Similar Messages

Maybe you are looking for