Snow Leopard installation on Mac Mini has failed

Hi,
Does anyone know whether Snow Leopard checks what hard disk is installed in order to satisfy installation requirements as I've fitted an SSD Hard Disk Drive in my Macintel Mac Mini and installing Snow Leopard has failed (no longer boots into any Operating System previous nor upgraded. (Mac OS X 10.5.8 previously installed)).
Thank you for any advice.
Best Regards.

It may not have anything to do with a new drive installation. Snow Leopard has just "bricked" my Intel Mac Mini hard drive - the original one. The first attempt at installation failed, so I tried an erase and instal. It seemed to work - briefly but when I tried to restore apps and settings from a Time Machine back-up it "hung" with only one minute of restoration to go. Now the HD appears to have failed, since it is unable to find any system folder and booting up via the Snow Leopard disc and bringing up the disc utility shows a greyed-out HD drive.
Some people on the MacBook Pro forum report a similar problem with the hard drive after Snow Leopard installation.

Similar Messages

Is it possible to get a new snow leopard installation disc if original has failed

We bought an MBP three years ago. We never took the installation discs out of the packaging. We just did and they have purple stains around the edge and don't work.
Obviously the mac is out of warranty, but it seemed worth asking as I have never known a DVD to acquire "disc rot" before.

Commercial disks, which Apple uses, are pressed and cannot degrade like that. If this was a brand new Mac, then either someone switched out the disks, or they were stained in some other manner. If you bought it used, then it's likely you were given copies. If they are original disks, they should be gray with white silk screened lettering. Anything else is a copy.
If you want machine specific replacements, which would include the bundled iLife software and other titles that are not on the retail disks, contact Apple. They will ask for the Mac's serial number to make sure you get the correct disks.

Question about installing Snow Leopard on a Mac Mini

I'm in the process of installing Snow Leopard on a Mac Mini, but it's taking forever. It's been installing for well over 2 hours now and still indicates an hour left to install. Is this unusual? I'm getting a little concerned. What do I do if I have to cancel the install? Do I have to start from scratch again?

How about this:
1. If necessary start up from the external HD & verify that everything is working right & all your files are intact on it.
2. Clone from the external to internal HD.
3. Start up from the internal HD & verify as in #1 that everything works as expected.
4. Install Snow Leopard on the external HD. If that completes successfully, restart from it & verify as above.
5.a. If that all checks out, clone the external back to the internal HD & you are done.
5.b. If that fails, you still have the internal HD with your working copy of 10.5.8 to use while you try to figure out what is going wrong.
The main benefit of this is you always have one working installation to fall back on no matter what happens.

Do I need a more recent mac mini to use my iphone 4 with. Im unable to download snow leopard because my mac mini is older. Do I need to get a new mac or is there something else i can do

Do I need a more recent mac mini to use my iphone 4 with. Im unable to download snow leopard because my mac mini is older. Do I need to get a new mac or is there something else i can do

Get Leopard.
System Requirements
Apple ID (required for some features)
Internet access6
Syncing with iTunes on a Mac or PC requires:
Mac: OS X v10.5.8 or later
PC: Windows 7; Windows Vista; or Windows XP Home or Professional with Service Pack 3 or later
iTunes 10.5 or later (free download fromwww.itunes.com/download)
http://www.apple.com/iphone/specs.html

I installed snow leopard on my mac mini and now it takes roughly 10 minutes to boot

I have a mac mini 1.5ghz with 1gb of ram installed.
I was running leopard with the combo update (10.5.8) but decided to install snow leopard as some of my apps need 10.6.8 to run.
The mac now boots past the grey screen with the apple logo then goes to a blue screen where i can move my mouse but nothing else.
This lasts for roughly 10-11 mins and then finally goes to my desktop and sure enough everything works perfectly and fast too.
It used to boot in around 30 seconds when i had leopard installed. If it can not be fixed i will be happy going back to leopard but i dont want to lose anything when i install it.
Any advice would be appreciated
Thanks

Mac OS X 10.6: If you see a blue screen at startup .
You may need to reinstall Snow Leopard:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Mac OS X 10.6.8 Update Combo v1.1.

Can I install Snow Leopard on a Mac Mini 1.5 Solo?

I bought a used Mac Mini. It is a 2006 I believe. It is a 1.5 Solo Core Intel. 2GB RAM. 60GB HDD.
I bought this for my kids, and wanted to wipe the drive and do a fresh install to ensure there would be no unexpected material to arise from a previous owner. I was given a Snow Leopard MAC OS X V10.6.3 Retail disk with the Mini. By starting from the install disk, I was able to wipe the drive. I did a simple zero data erase. Went smooth. I then started the install of SL. Chose language. Agreed to terms. Chose drive to install on. Told me it had 42 minutes to install. It then went to an error screen telling me the installation failed. Restart and try again. I have been through multiple attenpts at this.
I then decide to try my Leopard MAC OS X v10.5.4 Family Pack install disk that I have. I go through the same process to get an error telling me it could not install "essentials" and that I need to contact the manufacturer of the software.
Just out of morbid curiousity, I decided to put my SL disk in and give it one more try. Now when I get to the selct a disk to install on, it tells me there is a recoverable OS from a previous install that can be restored. Click customize to change install or click continue to recover the previous install. I got to 35 minutes and received the error screen. I have been thoughtful enough to include a picture of the error message I received.
It seems I have hit a wall. I am a mac guy. iPhone 4 / iPhone 5 / Mac G4 PPC Dual 1Ghz 2GB RAM / MacBook Pro 13" 2.4Ghz Core 2 Duo 4GB RAM / now this Mac Mini 1.5Ghz Solo Core 2GB RAM and a few others I have sold off over the years. I love them. Always have. But I cannot lie. I am ready to throw this Mini through a wall.
Am I missing something here?

There is no reliable way to test RAM short of a dedicated tester. There are software RAM testers that you can try - TechToolPro can do RAM tests:
http://www.micromat.com/techtoolpro
or you can try Rember/memtest:
http://www.macupdate.com/app/mac/15837/rember
but they can often find only the most obvious problems, and if there is such a problem it usually prevents the RAM test from running at all. It's worth trying, though, as it may turn up useful information.
As to the logic board, TechToolPro can do some testing there as well, and authorized Apple service centers have additional tools. There is no single "tell tale sign" of a logic board problem since, given the many different functions the logic board performs, there can be many different symptoms.
If things work properly with an external drive but not with an internal drive, I'd guess a problem with the SATA controller chain on the logic board, but that's just a guess. But if that is the case, then a logic board replacement will be necessary, and as you say that's probably not worth it for a Core Solo mini.
Regards.

Can I install Snow Leopard on a mac mini 2,1?

My mac mini 2,1 currently has OS X 10.5.8 wuth the Darwin 9.8.0 kernel. Can this be upgraded to Snow Leopard (10.6.X)? Is there good how to guide if yes?

Yes. Purchase the Mac OS X 10.6 DVD, start the Installer, and follow the onscreen directions.
(63289)

I can't install Mac OS X Snow Leopard on my Mac mini!

Hi,
I have a Mac mini 2007, with OS X 10.5.8
I want to install Mac OS X Snow Leopard, but i can't. I erased the hard drive with the installation disc of leopard and then i tried boot snow leopard. After a few seconds it said: "You can't install on this computer. What can i do?
My Mac mini's details:
Model Name:          Mac mini
Model Identifier:          Macmini2,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          1.83 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          2 MB
Memory:          1 GB
Bus Speed:          667 MHz
Boot ROM Version:          MM21.009A.B00
SMC Version (system):          1.19f2
Please help!

Where did you obtain the Snow Leopard DVD? If it is aDVD from another computer, it will not work. You will need the retail version of the DVD as shown below.
http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard

Can I install the ordinary Snow Leopard onto a Mac Mini Server?

I have a just-purchased 'Mac Mini with Snow leopard Server' (i.e. the model with two hard disks and no superdrive). I also have a copy of Snow Leopard - the ordinary version, not the server version. Although you might think this a weird thing to do, I may want to install 'ordinary' SL onto the Mac Mini. Is there likely to be any problem with that (I am hoping that the result will be more or less identical to purchasing an ordinary Mac Mini, except that I would have 2 disks instead of one and a superdrive)?

I've just discovered this question has already been answered:
http://discussions.apple.com/thread.jspa?threadID=2303656

Can i put snow leopard on a mac mini server? MORE INFO BELOW

Hi! I am getting a mac mini server in august (new hdmi type) and i dont want server becuase i am a home user. can i buy and install regular snow leopard (preferably mac box set) and will there be any software isues? questions: [email protected]

Double posting the same question is a good way to confuse everyone. I suggest you close at least one of these.
See your other posting for my reply.
Allan

Snow Leopard Server Software - Mac Mini Copy vs Retail Copy

Hi All,
I recently purchased a mac mini server, with what I thought would be a SL Server license.
I've used the Mac Mini to run a Leopard server whilst our Xserve was out of action.
Now the xserve is back, I was thinking of installing SL on the Xserve and keep the mini running leopard until we migrate over.
When I tried to install SL on the Xserve, it gave me an error. I rang Apple, and the enterprise guy told me this wasn't possible, as the copy that came with the mac mini was hardware specific and just a restore copy of snow leopard server. Bottom line I can't install the Mac Mini version of SL on an Xserve, even though I have paid for a SL license in buying the mac mini!
Does anybody know if there is any real differences between the hardware specific software copy and a retail version. If there isn't I'll install a copy on the mac mini and copy it over to the xserve. I just want to be sure that I'm not getting a downsized version of software!
Thanks.

There are ways to extract the OS from the restore disk so you can use in other system. you will just have to do a little online search. but I think it will be illegal if you care of course... but it would probably be easier to just download a copy from rapidshare or something like that and use your key ..
As far as feature there is none between the restore and retail copy.

I installed snow leopard on my mac mini and word won't open?

I upgraded my mac mini with snow leopard and now word won't open?

What version of Word?
Allan

I have snow leapard on my mac mini. Can I put lion on before mountain lion?

I have snow leopard on my mac mini. Can I put lion on before mountain lion?

I have snow leopard on my mac mini. Can I put lion on before mountain lion?

Mac OX Snow Leopard installation from DVD failed

I tried to install the new OS Mac OS X Snow Leopard 10.6.3 (bought today) on my iMac. But is constantly failed (message: installation failed) and now it's in a loop where I can't get out. Because the only action there is is to try it again. What should I do?

What specific iMac model do you have? Does it meet these requirements?
Snow Leopard General requirements
Mac computer with an Intel processor
1GB of memory
5GB of available disk space
DVD drive for installation
Some features require a compatible Internet service provider; fees may apply.
Some features require Apple’s MobileMe service; fees and terms apply.
To shut down the computer press and hold in the Power button until the computer shuts off. When you restart the computer you can eject the DVD as follows:
Five ways to eject a stuck CD or DVD from the optical drive
Ejecting the stuck disc can usually be done in one of the following ways:
1. Restart the computer and after the chime press and hold down the left mouse button until the disc ejects.
2. Press the Eject button on your keyboard.
3. Click on the Eject button in the menubar.
4. Press COMMAND-E.
5. If none of the above work try this: Open the Terminal application in your Utilities folder. At the prompt enter or paste the following:
/usr/bin/drutil eject
If this fails then try this:
Boot the computer into Single-user Mode. At the prompt enter the same command as used above. To restart the computer enter "reboot" at the prompt without quotes.
If you are currently running Leopard and it's still working then do this:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If all is OK then reboot from your Snow Leopard DVD and try the installation again.
BTW, I encourage you to make a cloned backup of your current working system before trying to upgrade.

Mac-Windows-Connection failes after Snow Leopard Installation

I am dealing with 4 PCs at home – an IMac, a MacBookPro, a Dell Dimension and a Dell Precision Workstation. Before I installed Snow Leopard I could connect easily from my Macs to my PC via “Connect with Server” and the “sudo pico /etc/hosts” hint to rename my Windows-PC to real names (e.g. Dimension and Precision). After the installation I am prompted in OS X to give my account name and password again! And, of course, I don’t work anymore (wrong user name or password error). Because I put those information in long ago, I am not quite sure if I am putting the wrong Name/Password info in or if something happened during the Snow Leopard installation. I was never quite sure if “Name” meant the name of my Windows account I want to log into, or my Mac user name or a combination of both or the Server /Name thing, e.g. Dimension\Name. Just for info: My Windows-PCs can still connect without a problem to both Macs.
Any help is appreciated what information exactly to put in that **** Name/Password box that appears if I want to connect to a Windows-PC from my Mac. Or what else could have happened during the Snow Leopard installation that cut of the former available ability to connect to my Windows-PC from OS X.

I was able to see the other Windows XP computer and begin to connect. I was then presented with a login screen. I tried using the usual user name and password - no luck. I then formatted the user name as as follows:
user name: computer name\user name
password: as normal
And it worked. Specifically in my case:
user: cwy-pln2152\administrator
password: planning
This is what worked for me your mileage may vary.

Snow Leopard installation on Mac Mini has failed

Similar Messages

Maybe you are looking for