So every time i start up my comp i get a white screen with a question mark on a file. It also makes the clicking sound that it makes when its thinking. what do i do?

i have tried rebooting with the command+option+p+r keys and that doesn't work
i have tried holding down the shift key and that doesn't work
i have tried inserting the cd that it came with but nothing happened
i have only had it for about a year
am i screwed?

If it is a Mid 2012 model it did not come with a CD or DVD. So I don't know what disc you are using but it certainly did not come with the system. Now if it is older the a 2011 model then those came with optical discs.
Try holding down the Coomand+r key yo boot to the Recovery HD partition. If that doesn't work hold down the Command+Option+r keys until you see a spinning globe in the center of the screen. From that you can use Disk Utility to check the internal hard drive.
But I suspect your drive might be failing or it is totally corrupted. If the system is less then a year old you are still inside the one year warranty period and if you are I suggest you take it to an Apple store to checked out and fixed under that warranty.
Also if the system is still within the one year warranty I suggest you buy the Applecare Extended warranty. You may need it.

Similar Messages

  • When I start my Mac air I get a flashing folder with a question mark

    I am trying to start my Mac air and I get a flashing folder with a question mark. When I turn the power of it shuts down but wen starting it comes back

    Just being clear about your situation.  When you hold down Option during boot it does not show a system volume or a recovery volume from which to boot.  At that point if you select a network boot and you do not see a spinning globe that persists there a good while as it loads the recovery partition over the network.  True?
    A couple of more thinks to try:
    Disconnect all of your external devices.
    Reset PRAM
    Boot with the option key again.
    Standard things to try (which is sounds like you already have attempted) A flashing question mark appears when you start your Mac

  • Imac G5 won't start white screen and flashing question mark

    tried every key combo recomended -   erased HD using target mode/firewire with laptop - but won't boot up from install disc...

    The white screen with flashing question mark means that it cannot find a bootable volume.
    The iMac G5 will not boot from just any install disk. Ideally, use the grey restore disks which came with the computer. If you've lost these, you can order them direct from Apple. Alternatively, a Mac OS X 10.5 retail install DVD will work provided the iMac G5 has also 1GB RAM (minimum requirement for 10.5).
    Sometimes, if the internal drive is faulty, it can take a long time for the computer to recognise other disks. I would suggest holding down the option key on the keyboard (labled alt on some keyboards) and turning the computer on, keep holding alt until you get to the early boot menu, insert your DVD/CD, and click the circle arrow to refresh, wait a bit and the DVD/CD will show up and you can click on it to select it and boot from it by pressing the straight arrow.
    After a little while it will get to the install menu, select your language, then on the next screen go through the menus to find "Disk Utility" (it's in different places on different versions of Mac OS X).
    You will want to check that the internal hard drive is detected, and that it doesn't have a SMART error (it might be red, or say that the disk is failing). If you get that far, then (assuming you have erased the disk previously, as this will step really will erase the drive and take all your data with it) partition the drive, making sure that under 'Options' you select Apple Partition Map (this will be the default on earlier versions of Mac OS X, but might not be if you've erase the disk from an intel Mac like a MacBook).
    Once, you done all that, and there haven't been any issues, you should be able to quit Disk Utility, and carry on with the sytem install as usual, and a 30mins to 2 hours and reboot later you should be booting from the internal drive again.

  • Every time i start my MacBook Air i get the spinning wheel and have to soft boot (shift, control, option, power) it three or four time s before it starts

    Every time i start my MacBook Air i get the spinning wheel and have to soft boot (shift, control, option, power) it three or four time s before it starts. It has only been over the last week or so I also found Safari will not load up and tyou have too open then shut from the drop down then restart it to get a page, any help pleas?

    Do this:
    Reinstall Lion, Mountain Lion, or Mavericks
         Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
         COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
         after the chime press and hold down the OPTION key until the boot manager screen appears.
         Select the Recovery HD and click on the downward pointing arrow button.
         Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu.
         Repair the Hard Drive and Permissions as follows.
    After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
         Reinstall Lion/Mountain Lion, Mavericks: Reboot from the Recovery HD. Select Reinstall
         Lion/Mountain Lion, Mavericks from the Utilities menu, and click on the Continue button.
         Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
                    three times faster than wireless.

  • What does it mean when starting up, all you get is an envelope with a question mark in it?

    what does it mean when starting up, all you get is an envelope with a question mark in it?

    You should reinstall OS X. See the following for reinstalling instructions for Lion/Mountain Lion or Snow Leopard:
    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Mac OS X 10.6.8 Update Combo v1.1.
    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Getting a folder icon with a question mark in it when I start up...

    Hi Guys
    I know this isn't a Logic or music-related question, but I trust you guys so I'm asking it here rather than in one of the other Apple forums...!
    Sometimes when I start my 2 month old Mac Pro, I get a folder icon in the middle of the screen, with a question mark in it...
    This happens approximately one in ten startups...
    Does this mean there's something wrong with my boot hard drive? Or some other kind of problem?
    If I switch off and start again, it always starts up fine, but I'd be worried if this might indicate my system hard drive is on the way out!
    Any advice?
    Cheers and thanks!
    Mike

    You cannot delete (just try it) the Network Startup icon, and I don't think it is the problem. That question mark folder on startup actually tells you that the Mac cannot find a valid system, so if I were you I'ld run a couple of utilities, repair permissions, perform a surface scan of your boot disk etc.
    And post the question on the OS X and the Mac Pro forums too.
    The question mark in the network startup icon in the Startup Disk Prefpanel simply means that there is no network startup system. I have the same icon. It is not the problem. However, if for some reason your Mac decides on its own to try and start up from it, it would explain your "where's the system" startup ?-folder.
    It could mean a lot of things: something almost broken in your system, or maybe a firmware problem or maybe a disk, or even that your keyboard is defective, and that (for example) the letter C hangs 1 in 10 times, making your Mac look for a Boot CD/DVD that isn't there...
    Regards, Erik

  • My iMac Version 10.6.8 has problems starting up. I often get a white screen without the apple icon.

    My iMac Version 10.6.8 has problems starting up. I often get a white screen without the apple icon. Then I must turn the computer off and restart. Restarting will usually bring up the Apple icon and the start screen. What could be causing this? And how can I resolve this issue. My Mac is still under warranty, I've had it just 7 months.

    Reset the NVRAM/PRAM and Reset the SMC.

  • HT1310 when i starst my mac i get a flashing folder with a question mark. i tried rebooting and holding the option button then i get 2 boxes, one with a refresh arrow and one with a forward arrow neither of them seem to do anything. now what

    when i starst my mac i get a flashing folder with a question mark. i tried rebooting and holding the option button then i get 2 boxes, one with a refresh arrow and one with a forward arrow neither of them seem to do anything. now what

    Here is an article that describes what it is supposed to do:
    Startup Manager: How to select a startup volume
    If no Volumes are shown, it is telling you there are no potentailly bootable Volumes attached. That means your boot drive has died or the bootable image on it is unrecognizable.
    What Mac Pro ? by year, GHz, number of processors, screen size?
    What Mac OS X ?

  • MacBook Pro won't boot at start.  I get a white screen with a blinking folder with a question mark in the middle. Any ideas?

    MacBook Pro won't boot at start.  I get a white screen with a blinking folder with a question mark in the middle. Any ideas?

    Read this article...
    http://support.apple.com/kb/TS1440?viewlocale=en_US&locale=en_US

  • Every time I start Firefox, why do I get a Google sign-in tab?

    I’m using Firefox for Mac vets. 34.0.5, and I get that extra tab that opens every time I start Firefox in addition to the Home page I specified in Preferences. How do I stop that from happening?

    Type '''about:config'''<Enter> in the address bar.
    If a warning screen comes up, press the '''Be Careful''' button.
    This is where Firefox finds information it needs to run.
    At the top of the screen is a search bar. Type '''browser.newtab.url'''
    This tells Firefox what to show when a new tab is opened.
    If you want, right click and select '''Modify'''. You can change the setting to;
    '''about:home''' (Firefox default home page),
    '''about:newtab''' (shows the sites most visited),
    '''about:blank''' (a blank page),
    or you can enter any '''web page''' or '''about: page''' you want.
    The same instructions are used for the new window setting, listed as
    '''browser.startup.homepage'''.

  • What do I do when I start my iMac I get a white screen with an apple and a moving circle?

    All I get when my iMac is turned on is a white screen with an apple and a moving circle.  What should I do to get the iMac to boot?

    Do you have reliable backup you can restore from, as an erase and re-install may be required?
    Before you got down that route, it's possible that it might get fixed if you try again. Not sure about that particular error, but I have had errors in the past that Disk Utility wouldn't fix on the first attempt but then subsequently did.
    It's also possible that the (around $99, I think) Disk Warrior might resolve it - but not guaranteed.
    However, I just found this thread: https://discussions.apple.com/thread/3862376?start=15&tstart=0 have a look at Nirvi's post at the end - there may be hope (I've not tried this, although it seems to have helped a few, although not everybody - so at your own risk and I wouldn't try it if I didn't have backup).

  • I get a white screen with a grey flashing folder icon with a question mark in it when i try to start up my i mac, what's happening?

    A few days ago my i mac when into grey screen; there were a few options for starting up, restoring etc i tried all of them to the extent possible but didn't work. Then i decided to unplug my external backup drive in case it may be erased or info lost in this process and now all i get when i turn it on is a white screen with a flashing folder and question mark. Any ideas?

    That indicates the computer is having difficulty finding the startup volume. Your internal HD may have failed or the system may have "forgotten" where it is. If you are using Lion or later (10.7.x or later) then restart in the Recovery Partition and choose the startup disk.  Before doing anything carefully read and follow Apple's instructions in:
    A flashing question mark or globe appears when you start your Mac

  • When i open my computer I get the white screen with apple symbol and there are vertical lines all over the screen with green pixels and after a few minutes the screen gets grey and I get message to restart my computer what happens

    3 years ago I bought an IMac Desktop that I am using for a lot of things but the most important for dvd montage in Imovies and Idvd.
    Now today when I opened my computer I get as usual the white screen with the Apple symbol but there were all over the screen vertical lines with green pixels and after a while the screen gets grey and I get message to restart my computer using the power button or the restart button and when I do so each time the same is happening somebody can tell me what is happening and what caused this. This computer is my work and now I have no income anymore.
    On the Apple support site they are asking to enter the serial number and when I do so I get message it is wrong but it is the only one I have and I buy this computer in Cairo Egypt. I am living in Hurghada in Egypt for the moment. When I call the technical support of the shop where I buy it they are telling me that it is the hard disk or ram and that I probably lost everything on it and they are asking a big amount to repair.
    Can somebody advise me on this matter. Thanks in advance

    You can find the serial number either in About this Mc in the Menu bar under the , or it should be on a sticker under the foot of the machine.
    If you have the install discs, try booting from them, holding down the c key and then using Disk Utility to check the drive. 
    You can also boot into Safe mode
    To start up into Safe Mode (to "Safe Boot"), do this:
       1. Be sure the computer is shut down.
       2. Press the power button.
       3. Immediately after you hear the startup tone, press and hold the Shift key.
          Tip: The Shift key should be held as soon as possible after the startup tone but not before.
       4. Release the Shift key when you see the gray Apple and progress indicator (looks like a spinning gear).
    During the startup in Mac OS X 10.2 through 10.3.9, you will see "Safe Boot" on the Mac OS X startup screen.
    During the startup in Mac OS X 10.4 or later, you will see "Safe Boot" on the login window, which appears even if you normally log in automatically.
    Please post back with results,
    To leave Safe Mode in any version of Mac OS X, restart the computer normally, without holding any keys during startup.

  • Getting a flashing folder with a question mark when starting Imac.

    I got this flashing folder with a question mark on it when starting my Imac this morning. Im running on Osx 10.6. I put it in target disc mode and connected it to my macbook pro. I opened the disc utility app on the macbook and found my imac. I "verified" it and found an error. When I clicked "repair" the disc utility app froze and crashed. When I opened it again my Imac didn't show up. I've restarted both computers several times with no luck. Whats my next step?

    Hi.
    Try restarting your iMac while holding down the option (alt) key until the spinng gear appears.  You should momentarily be presented with a list of startup drives to select.
    Choose Macintosh HD (your normal startup disk drive) and click the right-arrow.
    When your iMac boots, go to System Preferences > Startup Disk and again select your normal startup disk. Then click Restart.
    I hope this is helpful.
    EDIT - disconnect the machines from each other first.

  • My macbook 13' (older version) starts only to white screen with apple logo tried to rebooot by pressing shift at the opening but it didn't finish starting before stopping please help anybody please

    is anbody there how does this work never done it before my macbook won't start past white screen with apple logo any ideas ?

    Are you using a 10.6 Snow Leopard Install DVD? If yes, you can erase and install following these directions: http://support.apple.com/kb/HT3910
    You'll know whether or not it is a hard drive issue when you get to step 8 under "Part One: Erasing the hard drive". If you do not see your hard drive in the list on the left side of the Disk Utility window then you know the Mac isn't seeing it—could be a loose cable, but more likely hard drive failure.
    If you can see it on the left, click on it and look at the bottom of the Disk Utility window. If you see something like "S.M.A.R.T status: failing" that is definitely a hard drive issue. Otherwise, you can just follow the directions for an erase and install!
    Might be worth fixing depending how much a repair would cost. Genius Bar could at least diagnose it for you and give a repair estimate. I'd look at what a new or refurbished one with your same specs would cost though to see if the price differential is worth it...

Maybe you are looking for