So how bad is this?

So today, for the first time in as long as I've owned my 2.0 GHz iMac G5, it just randomly shut down on me. I thought it was a one time thing, a power surge or something maybe, so I started it back up and went about my business. Then a few hours later, it happened again. And about 20 mins after that, again. By this point I knew something was up, so I backed up a couple vital files real quick, shut it down, and cracked it open.
This is what I saw:
http://img.photobucket.com/albums/v12/newtikki/DSC00185.jpg
So, I figured it was overheating because of the symptoms, but that looks really bad. When I closed it back up, I felt the slit in the back and couldnt feel any air coming out the half that the CPU feeds to, however, the other half (which i presume is pumped from the video card) was pumping warm air. So, how can I resolve this? I bought it in probably June of last year, so I don't have any warranty remaining. How much is this going to cost me?
Thanks,
Michael
iMac G5 Mac OS X (10.4.6)

Hi Michael,
My bet is actually that your primary problem is that the power supply is failing, and that your fans just might be running poorly because of dirt buildup or lower power.
Your Mac will cut out before heat doess any damage to the processor.
There are three fans - one for the Hd, one for the processor , and one for the "system" generally. The HD fan is really the one that does the most work usually. Its "base" setting is at 2300 RPM, while the CPU one sits down around only 1500 when its not doing a lot of work. Its only under load that it kciks up higher, and even then it will rarely be running as fast as the HD fan.
So you can almost always expect to feel a bit more breeze from the HD side than the processor side of the slot.
The general system fan usually sits on about 1700 rpm until things really start to heat up.
Cheers
Rod

Similar Messages

How bad will this hurt?

I have been considering buying a RV for a while. My boys aren't getting any younger. We currently have our house on the market. It seems like it is going to take forever to sell. My question is how bad do you think it will hurt my credit if I were to take out a small loan for approx $10,000 for a RV? My credit scores on fico 8 are around 660-670. I know waiting until after we buy a house is probably the best idea, but it just doesn't seem like it's going to sell anytime soon and I am dying to go camping and enjoy the summer with my husband and two boys.

Kyliemarie85888 wrote:
I have been considering buying a RV for a while. My boys aren't getting any younger. We currently have our house on the market. It seems like it is going to take forever to sell. My question is how bad do you think it will hurt my credit if I were to take out a small loan for approx $10,000 for a RV? My credit scores on fico 8 are around 660-670. I know waiting until after we buy a house is probably the best idea, but it just doesn't seem like it's going to sell anytime soon and I am dying to go camping and enjoy the summer with my husband and two boys.How about teaching your boys the joy of camping in a tent while hiking in the mountains or in a campground? Most boys would rather do this than hang out in a motorhome. (Motorhomes: Think retirees). I have been reading a lot about personal finance and the rule seems to be borrow only for necessities, pay cash for luxuries. Just something to think about. I know RV's can easily cost 60K - 100K or more, so I might be concerned about a 10K RV needing expensive repairs. Your boys won't be boys forever, but the important part is that you spend time with them. They don't need an RV to enjoy their parents. You could also rent a lot of nights in a nice cabin for less than 10K if you don't like sharing your bedroom space with bugs and bears.

Just how bad is this phone ? (E70 revisited)

I have actually forgotten how frustrating Nokia phones can be as I had confirmed by (then) new E70 to the bottom drawer because with the firrmware on it, it wouldn't work in my bluetooth enabled BMer.
What joy when I learned of the new version. Could it be that version 3.0633.09.04 (where do these numbers come from) would solve my problem ?
Well I don't know. In fact I don't even know why I tried to put it on the phone. First I downloaded the latest PC Suite (the phone I have which actually works is NOT a Nokia, so I didn't have that on the PC ). Then I downloaded the software updater. Then I connected by recharged (and still plugged into the adaptor) E70, and fired up the updater.
Next the USB message that my phone was disconnected from PC-Suite appeared, and as predicted the updater actually told me there was an update. I now had the option to leave or continue. When I continued, I got a message which told me the updater could not verify my phone !
No WAIT !! I got past this by restarting, and while the message to get out was still on the screen, I used the utility in PCSuite to reselect my phone, and when the updater continued it started the download of 48.1M. Great.
Next it came to the update bit. Again the process failed and again the solution was to do the little tinker with PC Suite to get past that point. In fact I got all the way to where the phone reboots, and shows the Nokia test screen. Here the phone seems to reconnect itself, but either its not fast enough or it's not connecting to the updater, because it reports that the update has failed. Sad but true.
Should I have known ? Should I have guessed ? I have a buddy who has had an E61, an E70 and now wants to try the E90. Is he crazy or what ? S60 does for telephony what Locusts do for corn. If only words would describe how bad this series of phones really is...
For those of you still here, who are in the queues for the E90, I admire your sense of endevour ! May the force be with you.

02-Oct-200705:53 PM
joevpt wrote:
You'd think... Eh!
What I found was that at various stages during the upgrade the NSU disconnects from the phone (which allows PC-Suite reconnect). When the NSU needs to reconnect, PC-Suite was holding onto the connection (because, I think, NSU only disconnects it once at the beginning... )
Regards,
Joe
Patheticlly true.

Exactly how bad is this explain plan?

Hi,
I'm on Oracle 9i - 9.2.0.6.0.
First, please excuse my question, I'm not that good at reading explain plans.
I have this explain plan:
| Id | Operation                                 | Name                      | Rows | Bytes |TempSpc| Cost (%CPU)|
|   0 | SELECT STATEMENT                          |                            | 70057 |    20M|       |   114K (12)|
|* 1 | FILTER                                   |                            |       |       |       |            |
|   2 |   TABLE ACCESS FULL                       | DUAL                       |    82 |       |       |     3 (34)|
|* 3 |   INDEX RANGE SCAN                        | CHANGELOG_1                |     1 |    44 |       | 2217   (3)|
|   4 | NESTED LOOPS OUTER                       |                            | 70057 |    20M|       |   114K (12)|
|   5 |   NESTED LOOPS OUTER                      |                            | 67062 |    18M|       |   113K (11)|
|   6 |    NESTED LOOPS OUTER                     |                            | 64194 |    16M|       |   111K (10)|
|   7 |     NESTED LOOPS OUTER                    |                            | 61450 |    14M|       |   110K (9)|
|   8 |      NESTED LOOPS OUTER                   |                            | 58823 |    13M|       |   109K (8)|
|   9 |       NESTED LOOPS OUTER                  |                            | 56308 |    12M|       |   107K (6)|
| 10 |        NESTED LOOPS OUTER                 |                            | 53900 |    11M|       |   106K (5)|
| 11 |         NESTED LOOPS OUTER                |                            | 51596 |    10M|       |   105K (4)|
| 12 |          NESTED LOOPS OUTER               |                            | 49390 | 9212K|       |   104K (3)|
| 13 |           NESTED LOOPS OUTER              |                            | 47278 | 8310K|       |   102K (2)|
|* 14 |            HASH JOIN                      |                            | 31639 | 5067K| 4576K| 7331 (13)|
|* 15 |             HASH JOIN                     |                            | 31639 | 4202K| 1936K| 1372   (9)|
| 16 |              TABLE ACCESS FULL            | COMPANY                    | 76111 | 1040K|       |   335 (15)|
|* 17 |              HASH JOIN                    |                            | 31649 | 3770K|       |   933   (7)|
| 18 |               TABLE ACCESS FULL           | AGREEMENT                  |   149 | 3129 |       |     3 (34)|
|* 19 |               HASH JOIN                   |                            | 31649 | 3121K|       |   928   (6)|
| 20 |                TABLE ACCESS FULL          | CONCRETEAGREEMENT          | 34172 |   333K|       |    55 (24)|
|* 21 |                TABLE ACCESS BY INDEX ROWID| SPECIFICATION              | 31649 | 2812K|       |   866   (4)|
|* 22 |                 INDEX RANGE SCAN          | SPECIFICATION_DATE         | 37437 |       |       |   143   (5)|
| 23 |             TABLE ACCESS FULL             | PERSON                     | 1786K|    47M|       | 4584 (11)|
|* 24 |            TABLE ACCESS BY INDEX ROWID    | INFORMATION                |     1 |    16 |       |     4 (25)|
|* 25 |             INDEX RANGE SCAN              | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 26 |           TABLE ACCESS BY INDEX ROWID     | INFORMATION                |     1 |    11 |       |            |
|* 27 |            INDEX RANGE SCAN               | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 28 |          TABLE ACCESS BY INDEX ROWID      | INFORMATION                |     1 |    14 |       |            |
|* 29 |           INDEX RANGE SCAN                | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 30 |         TABLE ACCESS BY INDEX ROWID       | INFORMATION                |     1 |    14 |       |            |
|* 31 |          INDEX RANGE SCAN                 | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 32 |        TABLE ACCESS BY INDEX ROWID        | INFORMATION                |     1 |    11 |       |            |
|* 33 |         INDEX RANGE SCAN                  | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 34 |       TABLE ACCESS BY INDEX ROWID         | INFORMATION                |     1 |    13 |       |            |
|* 35 |        INDEX RANGE SCAN                   | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 36 |      TABLE ACCESS BY INDEX ROWID          | INFORMATION                |     1 |    12 |       |            |
|* 37 |       INDEX RANGE SCAN                    | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 38 |     TABLE ACCESS BY INDEX ROWID           | INFORMATION                |     1 |    15 |       |            |
|* 39 |      INDEX RANGE SCAN                     | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 40 |    TABLE ACCESS BY INDEX ROWID            | INFORMATION                |     1 |    17 |       |            |
|* 41 |     INDEX RANGE SCAN                      | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
|* 42 |   TABLE ACCESS BY INDEX ROWID             | INFORMATION                |     1 |    17 |       |            |
|* 43 |    INDEX RANGE SCAN                       | INFORMATION_SPECIFICATION |     2 |       |       |     3 (34)|
---------------------------------------------------------------------------------------------------------------------                     I can see that there are some FULL TABLE SCAN, but this may be OK. What worries me is the combination with numerous NESTED LOOPS.
A CTAS for approx 500.000 records out of 14.000.000 runs in about 180 mins. This is too much. My guess is that it should/could be brought down to something like 20 min.
For completeness, the query in question:
SELECT *
FROM stik_spec_inf_v
WHERE spdate >= to_date('15-03-2008', 'dd-mm-yyyy')
   AND spdate < to_date('15-04-2008', 'dd-mm-yyyy');Wher eview is created as
CREATE OR REPLACE FORCE VIEW stik_spec_inf_v
AS
   SELECT CAST(1 AS NUMBER(3)) dataversion
         ,sp.ID AS spid
         ,sp."DATE" AS spdate
         ,sp.valuedate
         ,sp.amount
         ,sp.amountcode
         ,sp.periodstart
         ,sp.periodend
         ,sp.ambcode
         ,sp.state AS spstate
         ,sp."TYPE" AS sptype
         ,sp.respitedate
         ,sp.stopcode
         ,sp.validcode
         ,sp.person
         ,sp.company
         ,sp.concreteagreement
         ,sp.reconciliation
         ,sp.partialscheme
         ,(SELECT 1
             FROM dual
            WHERE EXISTS(
                     SELECT 1
                       FROM changelog
                      WHERE targetclass = 'com.csc.jpay.voucher.Specification'
                        AND targetid = sp.ID)) spchanged
         ,i1.startdate AS daekgagedato
         ,i1.amount AS daekgage
         ,i2.startdate AS prmgagedato
         ,i2.amount AS prmgage
         ,i3.employerpercent
         ,i3.employeepercent
         ,i3.voluntarypercent
         ,i5.salaryperiod
         ,i6.groupcontractcode
         ,i7.workinghourspercent
         ,i9.startdate AS hiringdate
         ,i10.startdate AS resignationdate
         ,i21.policenumber
         ,ix."TYPE" AS leavecode
         ,ix.startdate AS leavestartdate
         ,ix.enddate AS leaveenddate
         ,pe.cpr
         ,pe.ksdid
         ,co.opkr_number
         ,a.NAME AS agreement_name
     FROM SPECIFICATION sp
         ,information i1
         ,information i2
         ,information i3
         ,information i5
         ,information i6
         ,information i7
         ,information i9
         ,information i10
         ,information i21
         ,information ix
         ,person pe
         ,company co
         ,concreteagreement ca
         ,agreement a
    WHERE 1 = 1
      AND i1.SPECIFICATION(+) = sp.ID
      AND i1."TYPE"(+) = 1
      AND i2.SPECIFICATION(+) = sp.ID
      AND i2."TYPE"(+) = 2
      AND i3.SPECIFICATION(+) = sp.ID
      AND i3."TYPE"(+) = 3
      AND i5.SPECIFICATION(+) = sp.ID
      AND i5."TYPE"(+) = 5
      AND i6.SPECIFICATION(+) = sp.ID
      AND i6."TYPE"(+) = 6
      AND i7.SPECIFICATION(+) = sp.ID
      AND i7."TYPE"(+) = 7
      AND i9.SPECIFICATION(+) = sp.ID
      AND i9."TYPE"(+) = 9
      AND i10.SPECIFICATION(+) = sp.ID
      AND i10."TYPE"(+) = 10
      AND i21.SPECIFICATION(+) = sp.ID
      AND i21."TYPE"(+) = 21
      AND ix.SPECIFICATION(+) = sp.ID
      AND ix."TYPE"(+) > 10
      AND ix."TYPE"(+) < 21
      AND pe.ID = sp.person
      AND co.ID = sp.company
      AND ca.ID = sp.concreteagreement
      AND a.ID = ca.agreement;Please excuse my lengthy post. I still hope for some valuable input.
Thanks
Peter

Hi,
I have tried with an in-line view as John suggested. This give a FULL TABLE SCAN on information.
SELECT /*+ RULE */ * FROM (
    SELECT sp.id spid, sp."DATE" spdate
     FROM (SELECT   SPECIFICATION
                   ,max(decode("TYPE", 1, startdate)) daekgagedato
                   ,max(decode("TYPE", 1, amount)) daekgage
                   ,max(decode("TYPE", 2, startdate)) prmgagedato
                   ,max(decode("TYPE", 2, amount)) prmgage
                   ,max(decode("TYPE", 3, employerpercent)) employerpercent
                   ,max(decode("TYPE", 3, employeepercent)) employeepercent
                   ,max(decode("TYPE", 3, voluntarypercent)) voluntarypercent
                   ,max(decode("TYPE", 5, salaryperiod)) salaryperiod
                   ,max(decode("TYPE", 6, groupcontractcode)) groupcontractcode
                   ,max(decode("TYPE", 7, workinghourspercent)) workinghourspercent
                   ,max(decode("TYPE", 9, startdate)) hiringdate
                   ,max(decode("TYPE", 10, startdate)) resignationdate
                   ,max(decode("TYPE", 21, policenumber)) policenumber
                   ,max(decode(sign("TYPE" - 10),1, decode(sign("TYPE" - 21), -1, "TYPE"))) leavecode
                   ,max(decode(sign("TYPE" - 10),1, decode(sign("TYPE" - 21), -1, startdate))) leavestartdate
                   ,max(decode(sign("TYPE" - 10),1, decode(sign("TYPE" - 21), -1, enddate))) leaveenddate
               FROM information
              WHERE TYPE BETWEEN 1 AND 21
           GROUP BY SPECIFICATION) i
         ,SPECIFICATION sp
    WHERE 1 = 1
      AND sp.ID = i.SPECIFICATION)
WHERE spid = 1Any ideas on how to get around that?
Regards
Peter

Another battery expansion... How bad is this?

I was using my faithful MacBook Pro 17" to watch a 1080p video on my 42" LCD television, when I noticed that book was lifting up awkwardly. I turned it over and was startled to see the battery bulging from the laptop.
At first I was startled and turned the system off, then proceeded to remove the battery. I googled for similar situations and found it was more common than I would have expected.
It is a few few years old (I think it's an '08) model. What steps should or can I take regarding this situation; Is this covered by Apple or will I have to "bite the bullet" here and buy a new battery?

Has this really happened? Having spoken with multiple "Authorized Apple" technicians, I'm told that this is an isolated issue that is usually replaced after a phone call to Apple. Well, I've phoned Apple after being sent BY Apple to these technicians.
The result? I was told about all the customers that got free batteries for the same exact problem. In fact, I was told they were outside of their warranty period, AND did not require extended "AppleCare" due to the nature of this odd and rare occurrence. Furthermore, I was told that these batteries were replaced within three years from the date of purchase.
My laptop is NOT older than three years.
My laptop has been in the repair shop within the last few months already, and now my "laptop" cannot even leave the proximity of its power cord.
I think I may be beginning to lose faith in the Apple brand.

How bad is this recursive method?

Ignore the variable names.
     public static int reverse(int blah)
          String temp ="";
          String remaining = "";
          String number = Integer.toString(blah);
          if(number.length() == 1)
               return (Integer.parseInt(number));
          else if(number.length() != 1)
               temp = number.substring(number.length()-1, number.length());
               remaining = number.substring(0, number.length()-1);
               temp+=reverse(Integer.parseInt(remaining));
               return(Integer.parseInt(temp));
     }

Hello,
The code wont end if its length is >2.
Will not be recursive.
ex:
234
it will return 423
thats the only issue...
Edited by: amit.khosla on Mar 1, 2009 8:52 PM

HT4009 Ok so my problem is I put $100 on my account an it not letting me buy in app purchases an I'm ticked off to the max an idk how to fix this I bough in app the other day perfectly fine I need help bad HELP me

Ok so my problem is I put $100 on my account an it not letting me buy in app purchases an I'm ticked off to the max an idk how to fix this I bough in app the other day perfectly fine I need help bad HELP me

You need to Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

Graphics card Quadro K4200 don't work with cuda in Adobe Premiere CS 6 version 6.0.5. Maybe they are bad drivers for graphics card? How to solve this problem?

I have purchased graphics card Quadro K4200, but graphics card don't work with cuda in Adobe Premiere CS 6 version 6.0.5. Maybe they are bad drivers for graphics card? How to solve this problem?

Did you use the nVidia Hack http://forums.adobe.com/thread/629557

Power Point open multiple windows - how to avoid this bad behavior?

When one presentation is opened multiple ppt is also opened. It is told to be a Yosemite issue. Does anybody know how to stop this behavour?

Andrew, sorry, but that's not correct. That was true with the iBook, but the MacBook and MacBook Pro are designed to be able to run with the screen closed. It takes a hack (used at the owner's risk) to keep the MB or MBP from sleeping when the lid is closed, but both systems are engineered such that once the lid is closed and the system goes to sleep, it can be then awakened and run if an external monitor, keyboard and mouse are connected. This is by design and fully supported by Apple. Of course the MB/MBP needs to be in a setting where it gets full cooling; on a solid surface, nothing blanketing the top and nothing blocking the rear vents.
Regards.

How to do this issue with user-exit or badi

in migo transaction, after entering some purchase order number. go for item details.
In that in quantity tab, Qty in unit of entry field value should be empty when the purchase order number is entered. how to do this?
plz let me know as soon as possible.
it is urgent requiement .
points will be awarded.
thanking u in advance,
A.srinivas.

Hi Arthur,
Try this code ( i had changed only one line of code in your original code)
Set oGoodIssue = oCompanyDI.GetBusinessObject(oInventoryGenExit)
oGoodIssue.DocDate = "12/14/2007"
oGoodIssue.Lines.itemCode = "SR-5155"
oGoodIssue.Lines.WarehouseCode = "R5155KGS"
oGoodIssue.Lines.SerialNumbers.Add
oGoodIssue.Lines.SerialNumbers.SystemSerialNumber = CStr(1)
oGoodIssue.Lines.SerialNumbers.ManufacturerSerialNumber = "SR-0000001"
oGoodIssue.Lines.SerialNumbers.InternalSerialNumber = "SR-0000001"
oGoodIssue.Lines.SerialNumbers.SetCurrentLine 0
retval = oGoodIssue.Add
If retval 0 Then
oCompanyDI.GetLastError errMsg, errMsg2
sbo_application.messageBox errMsg & " (" & errMsg & ")"
Else
sbo_application.messageBox "Success"
End If
Hope it helps you
Regards
Vishnu

In my macbook pro when composing email it coping into thrash as well so how to stop this ?

in my macbook pro when composing email it coping into thrash as well so how to stop this ?

You may have a Bad fan. Make an appointment and take it to the genius bar for an evaluation. It's free, in warranty or out.

How to install this update and solve USB and touchpad issues?

I have Equium M50 (59E) and got bitten by an update that took out my touchpad and keyboard .I have made fresh install of XP Home and have all updated drivers and all is going well .The last update i cant seem to fathom is for
Driver Ana _2005_10_24_V1.2 it is for ,Standard Open HCD USB Host Controller........X 2 .........
The update fixes all kinds of issues of the kind i am having and is a recomended update from Driver detective ,that i use offten .
The trouble is it says to uninstall drivers for the one i have installed allready and when i do this it knocks off my USB mouse leaving me not able to install the new ones .When i reboot it installs the ones i dont want reinstalled .
This is the read me off the new update and realy it is beyond me to underdstand what to do ............so here it is ?
Driver revision history:
Twinhan VP704A Driver Release note
Note:
1.In case the system crashes while running with VP704A, Please install ULI
USB 2.0 host driver in \ULiUSB20Driver
2. For XP/SP1, please update with the patch in
<http://www.microsoft.com/downloads/details.aspx?displaylang=zh-tw&familyid=733dd867-56a0-4956-b7fe-e85b688b7f86>
3.In XP/SP1, updating driver will crash the system, while new install is ok.
The trick to update driver in XP/SP1 is shown in the following steps,
a. Uninstall the driver
b. Unplug and plug the USB device
c. Install the driver
4. To support remote controller, please launch Agent.exe in \Agent.
Further details can be found in \Agent\Readme.txt
Known issues:
1. Multi-instance is not supported
2. Remote wakeup is not supported
3. High CPU usage in Analog audio/video capture
4. Bad VBI Signal using YUY2 color format
5. AV out of sync if audio captured from wrong filter.
(Fix:using the filter "USB Audio Device" in WDM stream capture device)
6. Noise with analog-TV and FM Radio
(Fix:using the filter "USB Audio Device" in WDM stream capture device)
Driver revision history:
2005/10/24, Version: 1.0.2.8
Bugs fixed and new features:
1.Crossbar not properly set.
2005/10/21, Version: 1.0.2.7
Bugs fixed and new features:
1.Firmware version read from FLASH OK!
2005/10/14, Version: 1.0.2.6
Bugs fixed and new features:
1.Mutil-Access driver blank part below part screen when VBI!
2.Mutil-Access driver HCT driver verify crash fix!
2005/10/07, Version: 1.0.2.5
Bugs fixed and new features:
1.Tuner Power off when S-Video,Composite.
2005/09/30, Version: 1.0.2.4
Bugs fixed and new features:
1.Agent.exe updated for repeat bug!
2.TI5150 Register for Video Format fix!
2005/09/29, Version: 1.0.2.3
Bugs fixed and new features:
1.A trial driver build for multiple access support. (in the folder "\Multi-Access")
Note: "USB Audio device" filter provided by system does not support mutil-Access.
2.Reset TI5150 when a new frequency is set
2005/09/27, Version: 1.0.2.2
Bugs fixed and new features:
1.Fix I2C unstable access on some devices.
2005/09/23, Version: 1.0.2.1
Bugs fixed and new features:
1.Analog TV becomes darker sometimes.
2005/09/15, Version: 1.0.2.0
Bugs fixed and new features:
1.Fix INF for Windows 2000 installation.
2.FM radio scan policy changed!
2005/09/13, Version: 1.0.1.9
Bugs fixed and new features:
1.USB serial number string not visible with USBView, firmware update required.
2.FM radio scan policy, return unlock if PLLOffset>=9x12.5KHz
2005/09/13, Version: 1.0.1.8
Bugs fixed and new features:
1.After switching between A/D/AV several times, video display becomes dark in THDTV 2.61
2005/09/12, Version: 1.0.1.7
Bugs fixed and new features:
1.Improve channel lock status check performance
2.Pinnacle INF Fix.
2005/09/09, Version: 1.0.1.6
Bugs fixed and new features:
1.Add some audio initialization function.
2005/08/31, Version: 1.0.1.5
Bugs fixed and new features:
1.NTSC & PAL mode resolution separation.
2005/08/30, Version: 1.0.1.4
Bugs fixed and new features:
1.AvgTimePerFrame.
2.Frame Drop.
3.Pinnacle inf file HCT chkinf fail.
2005/08/22, Version: 1.0.1.3
Bugs fixed and new features:
1.Add Remote controller interface in digital source filter.
2.A new Remote controller test tool with source code in \Test_RC.
2005/08/16, Version: 1.0.1.2
Bugs fixed and new features:
1.Reorg Pinnacel & Twinhan's driver & folder.
2.VP704A_BDA_Test tool, add system code test.
3.Set IR protocol standard by registry keys "IRSTANDARD", "IRSYSCODECHECK1" in INF file.
4.Firmware update
2005/08/15, Version: 1.0.1.1
Bugs fixed and new features:
1.Serial number function is lost while adjusting TV audio volume
2.RC6A CIR support
(This firmware uses GPIO3 (M9207 pin 80) to decode RC6 protocol.
The hardware should be reworked to connect M9207 pin 80 to CIR module and the fimrware
EEPROM should be flashed with \Firmware\M9207.bin )
3.Serieal number, MAC address and OEM device name supported.
Please refer to further details in \Firmware\readme.txt.
4.Ioclt sample source code included.
2005/08/08, Version: 1.0.0.10
Bugs fixed and new features:
1.Analog TV audio volume increase.
2005/08/04, Version: 1.0.0.9
Bugs fixed and new features:
1.Analog TV Video mode set failure.
2005/08/03, Version: 1.0.0.8
Bugs fixed and new features:
1.Off-centerf requency scan +/- 125Khz
2.Fix duplicated program scanned in MCE.
2005/08/02, Version: 1.0.0.7
Bugs fixed and new features:
1.THBDAConsole.exe "ulFixedBW", "ulDisableOffFreqScan", "ulMCEFreqTranslate" bug fixed
2005/07/28, Version: 1.0.0.6
Bugs fixed and new features:
1.THBDAConsole.exe "ulFixedBW", "ulDisableOffFreqScan", "ulMCEFreqTranslate" support
2.Improve I2C communication stability.
3.Unify Signal strength & quality indication as THBda ioctl interface.
4.Capture filter Lock status check.
2005/07/28, Version: 1.0.0.5
Bugs fixed and new features:
1. The same signal strength & quality indications as VP7046.
2. Debug build driver
2005/07/21, Version: 1.0.0.4
Bugs fixed and new features:
1.Update INF.
2005/07/20, Version: 1.0.0.3
Bugs fixed and new features:
1.Improve performance in PCM4
2.Switching from Analog TV Mode to FM Mode failure
2005/07/04, Version: 1.0.0.2
Bugs fixed and new features:
1.Production Tool FM test OK!
And here is the readme from the other file within the update ?
ULi PCI to USB Enhanced Host Controller Driver V1.72 for Windows 98 SE, Windows ME , Windows 2000 and Windows XP
INTRODUCTION
This driver supports ULi EHCI host Controller under Windows 98 SE, Windows ME , Windows 2000
and Windows XP.
CONTENTS OF THIS DOCUMENT
1. Installation Instructions
2. Uninstallation Instructions
1. Installation Instructions
(Windows 98 SE & Windows ME)
A.When ULi USB 2.0 Controller has attached on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- This program will copy driver files into your Windows system,then restart your computer.
2. After system reboot, Windows will find the new hardware "ULi PCI to USB Enhanced
Host Controller" and install the driver.
B.If no ULi USB 2.0 Controller on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- This program will copy driver files into your Windows system, then turn off your computer.
- Attach ULi USB 2.0 Controller card on your system and then reboot your computer.
2. After system reboot, Windows will find the new hardware "ULi PCI to USB Enhanced
Host Controller" and install the driver.
(Windows 2000)
A.When ULi USB 2.0 Controller has attached on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- This program will install and load the driver and you don't have to reboot the
computer.
B.If no ULi USB 2.0 Controller on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- This program will copy driver files into your Windows system, then turn off
your computer.
- Attach ULi USB 2.0 Controller card on your system and then reboot your computer.
2. After system reboot, Windows will find the new hardware "ULi PCI to USB Enhanced
Host Controller" and install the driver.
(Windows XP)
A.When ULi USB 2.0 Controller has attached on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- Click "NEXT"
- This program will install and load the driver and you don't have to reboot the
computer.
- After install ULi USB 2.0 driver successfully. System will detect "USB 2.0 Root
Hub". Please select "install the software automatically (Recommended)" and then
click "Next" button to continue install.
- This program will install and load the driver and you don't have to reboot the
computer.
B.If no ULi USB 2.0 Controller on system
1. Install ULi USB2.0 Driver
- Run the setup program.
- This program will copy driver files into your Windows system, then turn off
your computer.
- Attach ULi USB 2.0 Controller card on your system and then reboot your computer.
2. After system reboot, Windows will find the new hardware "ULi PCI to USB Enhanced
Host Controller", continue to install.
- After install ULi USB 2.0 driver successfully. System will detect "USB 2.0 Root
Hub". Please select "install the software automatically (Recommended)" and then
click "Next" button to continue install.
Notice:
If you can't setup driver successfully. Please reboot your system and then follow
above steps to install driver again.
2. Uninstallation Instructions
1. Open "Control Panel" folder.
2. Invoke "Add\Remove Programs" icon.
3. Choose "ULi USB2.0 Driver" item.
4. Click on "Add/Remove" button to remove drivers.
Change List:
1.74
1.fix issue that multi-interface keyboard can not be detected on the usb2.0 hub.
2.support all USB2.0 Host Controller.
1.73
1.fix issue that On Win98SE , Blue screen when unplugging some USB2.0 Scanner after scanning image.
2.fix issue that On Win98SE, Blue screen when unplugging some USB2.0 Scanner from USB 2.0 Hub after scanning image.
3.fix issue that On Win98SE, Blue screen while copying files across the SUNBOX UH-204 Hub.
4.fix issue that wirless lan will disconect when plug-in usb device.
1.72
1.Fix issue that system will crash when USB HD copy large file.
1.71
1.improve Power management function in Win98/ME.
1.70
1.Improve the function of devcie detection.
1.62
1.Fix the problem that a USB floppy under USB 2.0 HUB cannot function when system resume from suspend.
1.61
1.Fix the problem that some USB device under USB 2.0 HUB cannot be found if system resume from suspend.
1.60
1.To support power management functions when a HUB with USB device plug into
a root HUB.
1.57
1.Fix USB floppy with USB 2.0 HUB can't be detect issue.
2.Fix issue that audio can't display smooth when USB device attach to system.
3.Fix system can't detect USB dvice when USB device attach to system in
suspend mode.
4.Fix issue that when USB root HUB have full loading, USB HD sometimes
transaction fail.
1.56
1. Fix issue that DVD decoder device can't display properly.
1.55
1. Fix OTI USB 2.0 hand drive can't be detect issue.
2. Fix USB mouse can't use after resume from suspend.
1.54
1.Improve driver security.
1.53
1. Fix bulk transfer may stop if USB device is plugged in USB 2.0 hub
2. Fix USB 2.0 mass storage device can't be access after resuming from standby if there is another USB 1.1 device existing
1.52
1. Fix system pages fault when accessing mass storage device in Win98SE, or scandisk failure when selecting
automatically fix file system errors
2. Fix system may hang up in Win98SE/ME if USB 2.0 cardbus card is plugged
v.1.51
1. Improve USB 2.0 cardreader compatibility.
2. Fix USB IDE devices can't be accessed after resuming from standby/hibernation.
v1.50
1. Improve bulk transfer
v1.48
1. Fix USB 2.0 LAN driver installation hanging up
2. Fix some USB 1.1 cardreader can't be identified when plugged into USB 2.0 hub
3. Fix some laptops Win98SE booting hanging up
v1.47
1. Improve bulk transfer performance.
2. Fix USB 2.0 bulk webcam preview failure.
v1.46
1. Support USB 2.0 and 1.1 Isochronous devices
2. Fix system hanging up when rebooting system if USB 2.0 host controller is disabled in Win9X/ME
3. Fix system hanging up when uninstalling driver if there are USB 2.0 devices connected in Win2K/XP
4. Improve device detection capability in Win9X/ME
v1.45
1. Fix system hanging up when resuming from ACPI sleep mode.
2. Fix mouse sometimes doesn't disappear when it's unplugged.
3. Fix Win9X composite device detection failure and improve Win2K/XP composite device
v1.44
1. Support composite device
2. Improve device detection
v1.43
1. Improve IDE read/write transfer failure rate with USB 2.0 to IDE bridge on PC card platform
2. Fix high-speed device detected as full-speed device
3. Fix some USB mouses detection failure problem
4. Fix some USB 2.0 hubs detection failure problem
5. Fix Win98SE crashing if ULi EHCI 1.42 is installed
v1.42
1. Fix PC Card ejection hanging up in Win98/ME
2. Fix suspend/resume hanging up in Win98
3. Solve sometimes USB 1.1 device can't be detected if OS boots with USB 2.0 and 1.1 devices plugged
4. Fix some PC Card USB 1.1 device detection failure
v1.41
1. Add new feature that system can install driver before device is plugged.
2. Fix PCMCIA OHCI controller resource assign issue on Windos ME.
v1.40
1. Support Win9X/ME/2K/XP with ULi USB 2.0 driver.
2. Fix PCMCIA EHCI controller detecting USB 2.0 device problem in Win9X/ME.
v1.32
1. Fix issue that driver can't detect Microsoft driver in Windows XP
if OS path is not c:\windows.
2. Fix issue that driver can't detect USB 2.0 controller device in in some system.
v1.31
1. Fix issue that driver can't install on Windows 2000.
v1.30
1. Fix issue that Win9X/ME shows no USB 2.0 Root Hub.
2. Fix issue that hanging up when second entry into Win9X S1 with HID device plugged.
3. Fix issue that sometimes when you click "Scan for hardware changes".
to PNP ULi USB2.0 controller, system will informs you the usbehci.sys
file can't be found.
4. Fix issue that v1.20 finds no EHCI controller to install driver for after different
verison of ULi EHCI controller devices are plugged and unplugged.
5. Support installing driver for more than one ULi EHCI controller devices existing on
system at the same time.
6. Fix Win2K/XP shows USB Root Hub for USB 2.0 Root Hub.
v1.20
1.Support ULi USB 2.0 Host controller driver for Windows 98SE/ME/2000/XP.
ULi Coporation. (ULi) web sites:
http://www.uli.com.tw/ (Taiwan)
CAN ANYONE TREAT ME LIKE A TWO YEAR OLD AND GIVE SOME GUIDANCE AS TO HOW TO ACHIEVE THIS UPDATE .
i WOULD BE VERY GRATEFULL AND KIND OF THINK IT WOULD BE BENIFICIAL TO A LOT MORE PEOPLE AS I SEE A LOT OF XP AND PROBLEMS OF THE KIND THIS UPDATE IS SUPPOSED TO FIX .

It says above 2 relevant and 1 correct answere available .............
I'm new here so could anyone direct me to these answeres?

My iPod touch 4th gen iOS5.1.1 can't be recognised by my computer and I have tried different cables and usb ports but nothing has worked. The iPod is brand new and was only opened today. Any ideas on how to fix this?

I have just today recieved a brand new iPod Touch 4th generation iPod with the latest update. Everything else on the ipod is working and my computer is able to read the camera fine, but iTunes cannot recognise it - even after restarting and trying different USB ports and cables. There is nothing at all coming up on the device list and iTunes is working as it would if I had no iPod plugged in. This is my first iPod on this computer and I have already tried redownloading iTunes. My computer is a windows XP computer. Does anyone have any idea on how to fix this problem?

Since this is an XP machine, which version of iTunes do you have installed? Is it the latest version?
Have you tried starting iTunes, attach the USB end of the cable, then while holding the home button on the iPod connect the 30-pin connector end of the cable to the iPod...that is the recovery mode but also should make iTunes see the iPod.
If that doesn't work you may need to take the iPod back and have it tested by the genius bar techs to make sure the connector is not bad.

How bad can a company be?

I called BT around mid May. I informed them i was going to move to a new flat in NW2 in June. I told them the flat is being completely renovated and that i wanted to get a phone line. The BT employee on the phone did some checks and confirmed to me there was no active line (which i already knew: i said the flat was being completely renovated). He said i needed to book for a BT engineer to come, that there would be a cost and that i would need to take another 12 months contract. He also said he would cover for the engineer cost if i tenew my broadband with BT for another 12 months. I was reluctant to take another 12 months contract with BT for phone line and broadband because the fiber optic broadband i have been having with BT for the past 15 months was awful (regularly dropped, very slow speed at random times, more than once a week every week for 15 months). But in the end i accepted the offer, agreed to renew Line and brodaband with BT for another 12 months and booked for the BT engineer to come on 12th june. And that's when the nightmare started.
On 11th june, BT called. They lefta voicemail i could hardly understand then sent a weird sms: "Hello, SHREYA here. I have tried to speak with you today however, couldn't make a contact over the phone. please text back (at your normal rate) and we'll get back to you within 2 hours. We check messages from 8am ? 8.30pm Mon-Fri or 9am-6pm Sat." I had no clue who SHREYA was, considering they didn't even specify which company they work for. But after googling the number on the sms, i found out it was from BT. So i called BT and spoke to an employee who started to confuse me about "system issues". I was wondering "what do system issues have to do with me?"... The BT employee told me her manager would call me back. When the manager called me, he was even more confusing. At the end i asked him only 1 question "is the BT engineer coming on 12 june to set up the Bt line?". He replied "yes, between 07:00 and 13:00".
On 12 june, because i hadn't received any sms from Bt confirming the time window when the engineer is coming, i called Bt at 10:00. The Bt employee then told me "oh, it's cancelled". I then became very unhappy. I asked "why?". The Bt employee put me on hold and after 5 mun, hung up on me. I called Bt again, spoke to another few people from Bt but nobody was able to tell me why the appointment i booked 3 weeks earlier was cancelled. I was furious: i accepted to take another 12 months contract with Bt for line and broadband and this is how they deal with it.... I logged a complaint on the Bt website. I was told that a case manager would be appointed to help me and i spoke to that case manager today but so far i have had zero meaningful updates as to when the line will be set up. All she told me today is that a new order needs to be logged because there was an internal problem with the one logged 4 weeks ago. She even saud it will be logged tomorrow. I asked "why ligging it tomorrow? Why not today considering i have already been waiting for 4 weeks?" I got no replies to that question...
4 weeks wasted already, not sure how many more to come, and no commitments as to when i can expect the service. As if moving hoone was not streeful enough, i have to deal with a company like Bt. I have to chase them every single day to get an update, this is so stressful. What a poor level of service.
How bad can a company be?

I have 2 lines into my house. One with BT and one with Virgin Media. I placed an order with Bt to take over the Virgin Media line. So BT cancelled my existing BT line which was working perfectly and transferred the Virgin Media line onto the BT line they just cancelled. Then no broadband and no phone. I was told there was a fault on the line! There wasn't before they cancelled the line. I was told it had been fixed, I was told it hadn't been, I was told I would have phone and broadband in 24 hrs. I didn't. I was then told there was still a fault on the line despite an engineer stating unequivocally that there was no fault. I explained to BT that my son has severe learning disabilities and epilepsy and that he stops breathing when he has a seizure and we have to be able to call medics. BT told me to use my mobile phone and that he would not be regarded as a priority case!.
After another 2 hours on the phone to them today I am told that they have to put in new cables (what was wrong with the existing ones?) and that I might have phone line and broadband by June 26 - 10 days after they were just sopposed to take over a working phone line.
One would have thought that a telephone company would be able to take over a phone line - just a stretch too far for BT administration.
The Openreach engineers were very helpful and took extra time to speak to BT when at my house but to no avail.

How to populate this fields in ce_bank_accounts?

Hey there, first, i want to apologize for my bad english.
i'm working with Cash management and i'm using this API ce_bank_pub because the bank are internals. i have the load from banks and branch, and kinda the bank accounts, but i can´t find how to populate this fields, that are mandatory for my requeriment:
AUTORECON_AP_MATCHING_ORDER
AUTORECON_AR_MATCHING_ORDER
RECON_ENABLE_OI_FLAG
RECON_OI_FLOAT_STATUS
RECON_OI_CLEARED_STATUS
RECON_OI_MATCHING_CODE
AUTORECON_AP_MATCHING_ORDER2
this is my "flow of work", first, i load the data with SQL*Loader in a custom/personal table, after this, i have a cursor that select all the records of this table and do some validations, after this (and if all the records are ok) i use the API ce_bank_pub.
i don't know if that API support those fields, I've read the documentation but can not find what I require.
any help will be appreciate.
thanks a lot.
[SPANISH]
Estoy trabajando con una carga de bancos, sucursales, cuentas bancarias y usos de cuentas, hasta ahorita todo bien, solo tengo problemas al poblar los campos que se muestran en la parte de arriba en la tabla ce_bank_accounts, estoy utilizando el API ce_bank_pub ya que los bancos son internos.
mi procedimiento, o la manera que lo hago es ésta:
cargo los datos con SQL*Loader a una tabla intermedia/temporal por decirlo así, posteriormente un cursor selecciona los datos para realizar las validaciones y las reglas de negocio y si los datos son correctos utilizo el API, eso es en general para las 4 cosas, pero los campos de arriba no se como cargarlo, modificarlos o si hay alguna otra manera para agregarselos.
cualquier ayuda es apreciada.
Muchas gracias.

Hi Miguel,
hope this helps ...
AUTORECON_AP_MATCHING_ORDER - Order of matching statement lines to AP transactions, by transactions first or by batch first, lookup type BATCH_OR_TRX
AUTORECON_AR_MATCHING_ORDER - Order of matching statement lines to AR transactions, by transactions first or by batch first, lookup type BATCH_OR_TRX
AUTORECON_AP_MATCHING_ORDER2 - Order of matching statement lines to AP transactions, by transactions first or by batch first, lookup type BATCH_OR_TRX_OR_GROUP
For all the above three fields, navigate to Lookups from Cash Management responsibility and find the lookup type BATCH_OR_TRX, this will have 3 values, B for Batch, G for Group and T for Transaction ..... pass any one of the three value as per your requirement ..
RECON_OI_MATCHING_CODE - Open interface transactions matching code, T for matching by transaction number, D for matching by date and amount. Lookup type: OI_MATCHING_CRITERIA
For the above field, navigate to Lookups from Cash Management responsibility and find the lookup type OI_MATCHING_CRITERIA, this will have 2 values D for Date and Amount, T for Transaction Number .... Pass any one of the two values as per your requirement ...
RECON_ENABLE_OI_FLAG - Flag to indicate whether to allow reconciliation of statement lines to open interface transactions, Y or N
As per your requirement indicate Y or N ....
RECON_OI_FLOAT_STATUS - Code to specify the float status for open interface transactions
RECON_OI_CLEARED_STATUS - Code to specify cleared status for open interface transactions
I am not sure about the above two ...i.e. the values that needs to be passed ...
Regards,
Ivruksha

So how bad is this?

Similar Messages

Maybe you are looking for