So my droid razor hd wont go pass the red droid start screen,just spins and spins
So my droid razor HD wont go pass the droid start up screen,it just spins, it does let me power it down by holding the volume down and power keys,but that's it
From your posting it's sounds as if you have a "Boot Looping" Droid problem. They can be the end of a phone's life but there is also some things you can try to save your phone . Give this a try and you may also need to have the OS re-flash.
First of all remove the battery from your phone or tablet, and wait for almost 2 to 3 minutes. What if your device does not have removable battery? Well, then you can power off it for almost 4 to 5 minutes.
Now you need to boot into Stock Recovery Mode by Pressing and Holding the Volume Up+Home+Power buttons at the same time for a few seconds until you see the Android System Recovery menu on your screen.
You’ll be using the Volume Up/Down to switch between different options and Power button to select your desire option.
Now select the Wipe data/Factory Reset option and confirm it.
Additionally, take also the following actions:
– Wipe cache partition
– Go to Advance and Wipe dalvick cache
Now Go back to the main Recovery menu and Select the option Reboot System Now to Reboot your phone.
Similar Messages
-
My mac wont get passed the grey screen with the apple logo and the timing circle, please help
My macbook wont get passed the grey screen, I rebooted it, any suggestions?
Work your way throught this knowledge base article:
Gray screen appears during startup
http://support.apple.com/kb/TS2570
MacBook Pro, Mac OS X (10.6.7), 2.4GHz IntelCore i5 320 HD 8GB RAM -
My iPhone 4 wont turn on, It wont go passed the charging icon and then when I take the charger out it says it needs charge. Its not the charger as iv tried several and holding lock and home button doesnt work please help!!!!!
Hello there, Conorjl7.
The following Knowledge Base article provides some good, practical steps for troubleshooting issues with charging:
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Particularly:
If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge for up to 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue is persists, please contact Apple Support.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
I have a problem with itunes when I sync the saved music and want to sync my iphone 5 ios 7.0.6 no longer passes the music thing is that just stays on "waiting for sync" and not worry please help are more than 400 songs that do not want to hear who are wi
Plawexki wrote:
... do you know if the contacts, photos, messages etc will be wiped?
Yes... Everything will be Wiped and Replaced with what is currently on Your Mac.
SYNCING with iTunes
See here > http://support.apple.com/kb/HT1386
From Here > http://www.apple.com/support/iphone/syncing/
You may find this information of interest...
Have a read here...
https://discussions.apple.com/message/18409815?ac_cid=ha
And See Here...
How to Use Multiple iDevices with One Computer -
HOW TO PASS THE DATA FROM SELECTION SCREEN TO STANDARD TRANSACTION?
HI,
HOW TO PASS THE DATA FROM SELECTION SCREEN TO STANDARD TRANSACTION?
thanks,
samba.By selection screen, what do you mean? There is no selection screen in WDA as there was in classic dynpro. Do you mean you are using the Select-Options reusable component? Are you wanting to call a standard transaction via ITS - SAPGUI for HTML? Please provide more details to your question.
-
I have updated and restored my iphone and now it wont go bask the connect to itunes screen what do i do?
So what happens when you connect to iTunes?
-
my iTunes Match can not pass the step 2, it keeps repeat again and again. Pls advise. Thank you.
Very strange. Two items to try:
a. Enable iCloud Status and iCloud Download fields in Song view, sort on status and look for any 'waiting' or 'error';
b. If (a) looks good, establish a new user account, create an empty library and enable iTunes Match, confirm that this provides access to all Songs and is working well.
These are seeking to ensure both no bad Songs or local Library corruption - both are relatively quick. -
i just bought an ipod touch 4th gen and cant connect it to tunes i have registered it and downloaded latest itunes it wont pass the connect to itunes screen
Hi..
Try this support article > Can't connect to the iTunes Store -
After installing a software update on my Macbook Pro, it would not reboot passed the gray screen and then would shut down.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to a Mac Pro tower, not to any other model. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
please help,just got used Ipad, owner reset to factory before shipping but when i turned it on wont go past the apple screen and wont sync to itunes
Just make sure you have the latest version of iTunes installed on your computer, also try restarting the iPad by hold down the on/off and the home button until your see the Apple logo. As a final troubleshooting step, put your iPad in recovery mode.
-
I did a full system restore to my phone along with the new 7.0 update. Now I went to restore my phone setting back through Itunes and it goes through all the steps but when it is completed it wont get past the "Connect to Itunes" screen
So what happens when you connect to iTunes?
-
How to pass the values from one screen to another
HI,
consider me21n,
po is created with the item category L,so components tab is enabled.that u all know.
i have added the custom tab in the item details with netwt,gross wt,no of pieces and one more field.
those fields are also in component structure of material data.
i need to pass the matnr,maktx,quantity,ntwt,grosswt from the component to be displayed in the subscreen.
i used import mdpm to xmdpm from memory id 'subcon', where it is exported from the function module 'me_components-maintain'.
how to pass all the values from component of structure MDPM to the subscreen of custom tab in the item details.
help me pls........................'hi everyone,
MODULE status_0111 OUTPUT.
data : fill type i.
SET PF-STATUS 'xxxxxxxx'.
SET TITLEBAR 'xxx'.,
DESCRIBE TABLE lt_zzmm_po_comp LINES fill.
ctrl_0111-lines = fill.
ENDMODULE. " STATUS_0111 OUTPUT
MODULE fetch_data OUTPUT.
ctrl_0111-lines = 2.
import xmdpm to lt_xmdpm from memory id 'SUBCON'.
IF not sy-subrc eq 0.
CLEAR lt_zzmm_po_comp[].
LOOP AT lt_xmdpm.
MOVE-CORRESPONDING lt_xmdpm TO lt_zzmm_po_comp.
APPEND lt_zzmm_po_comp.
ENDLOOP.
MOVE-CORRESPONDING lt_zzmm_po_comp TO ctrl_0111.
read table ctrl_0111-cols into col where index = 3.
ENDIF.
ENDMODULE. " FETCH_DATA OUTPUT
MODULE pass_line OUTPUT.
READ TABLE lt_zzmm_po_comp INDEX ctrl_0111-current_line.
MOVE-CORRESPONDING lt_zzmm_po_comp TO ctrl_0111.
ENDMODULE. " PASS_LINE OUTPUT
flow logic
PROCESS BEFORE OUTPUT.
MODULE status_0111.
MODULE FETCH_DATA.
loop at lt_zzmm_po_comp WITH CONTROL ctrl_0111 cursor
ctrl_0111-current_line.
module pass_line.
endloop.
PROCESS AFTER INPUT.
MODULE USER_COMMAND_0111.
loop.
*module read_data.
endloop.
but i cant see my fields in the table control .....i dont know y it is not coming?can anyone help me with code... -
My blackberry wont turn on, the red light just flashes for about 10 seconds!?
My battery went too low for radio use last night, so i put it on charge when i got home. My charger is broken so it needs to be in a certain position to charge. I charged it throughout the whole night and when i woke up this morning it wont switch on. The red light just comes on for about 10 seconds. I have tried to different chargers one that does work aswel. PLEASE HELP.
maybe the charging port is broken? check inside it and see if it looks any different
-
This initially started out as me trying to get my battery to work. my battery was dying after a few minutes so I was trying to kill the battery and recharge it to see if I couldn't get it back to a full charge. This didn't work but after a day or so I noticed the computer running slow and when I went to start it a couple days later the apple icon page would pop up and the little grey wheel would just whir away below it like it was thinking. The screen was kinda hard to see. Since then I have tried several different things to get the computer to fire back up as it should. I have taken out the battery and left it hoping the internal battery would die and it would reset itself to a default mode. Didn't work so I then tried taking the battery out and just using the power cord. This didn't work. I tried putting the battery out and in while running on the power cord. this didn't work. I have tried holding the "alt/option" key and that didn't work. Although it did give me a different window. I have tried holding down the "f" keys. That didn't work. I have tried installing a disc to try and reinstall the operating system. That didn't work. I had to shut it down and restart it holding down the eject key to get the disc back. I am running out of things I can think of to try so if anyone has any ideas I am open to all of them.
Thank you,
SeldovianMac OS X: What is Safe Boot, Safe Mode?
Mac OS X: Starting up in Safe Mode
I have tried installing a disc to try and reinstall the operating system.
Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
Restart your computer when done.
Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
If you did manage to reach the desktop after doing any of the above
my battery was dying after a few minutes so I was trying to kill the battery and recharge it to see if I couldn't get it back to a full charge.
Apple/About This Mac/More Info/Hardware/Power/Battery Information - copy and paste the information here. Do not include any serial numbers.
I noticed the computer running slow
How large is your hard drive and how much hard drive space do you have left?
Mac OS X (10.4.3)
Update to 10.4.11 using the combo update or Software Update along with all the other updates that goes along with it. -
My ipad2 wont go pass the white apple logo how do i get pass it
Please someone help me. Im trying to turn my ipad2 I just got it I downloaded the software that need to be on there yesterday I went to turn on my iPad anyway come on I call customer service they told me to hold down the home button and the sleep mode button at the same time for 10 seconds until the Apple shows I did that the upper part came on but it won't let me get past that screen can someone please help me and tell me what I'm d
oing wrongI read your response in the other discussion. I didn't realize that you just bought this iPad. Is it really brand new? It shouldn't be doing this if it is brand new. But try rebooting again first.
If you rebooted the iPad like this .... Hold down on the sleep and home buttons at the same time for about 10 seconds until you see the Apple Logo on the screen - and if it will not go past that screen - then you need to restore your iPad because something went wrong when you updated the software.
This explains how to restore the iOS software.
iTunes: Restoring iOS software - Support - Apple
If that will not work or the device is not recognized in iTunes, you will need recovery mode.
iPad: Unable to update or restore - Support - Apple
No matter which way that you restore, your device will be erased so I hope that you have a backup that you can restore from when you get the iPad running again. If you don't, you will have to start all over again and download your purchased content in the purchased tabs of the various stores on the device.
Maybe you are looking for
-
In secondary window texts are not appeaerd in smartform
hi to all bfore main window,i create one window for header data. in this window only texts are there. in main window item data is dere. item data was appeared in main window. but in header data window header texts were not appeaerd,so plz giv me
-
Using Lightroom and PS Elements
I have been a Lightroom user since the beginning and have PSCS3 for when I need to do some more involved editing. (Not very often - probably 95% of my editing/adjustments are done in Lightroom exclusively, including my RAW conversions.) I have a frie
-
Here's what's going on: When I load iTunes, it says "loading library.xml" (or something to that effect.) If I leave it alone, it will result in a "iTunes has stopped working" message from Vista. If I hit cancel, it will load iTunes but my over half m
-
I have problem syncing my music to ipad. Most of the songs are duplicated but only in ipad. I checked the music library in itunes and there didn't have the duplicated songs like in the ipad. I can not delete the duplicated songs inmy ipad.
-
Make my files move with the Finder window?
I don't know how many of you are familiar with Windows, but in Windows Explorer, whenever you changed the size of the window you were viewing your files in, the files would move with the size of the window while still staying in the same order. When