SOAP service works - but doesn't call application logic

I have an SAP enterprise service that's acting weird. Like any other SOAP service, I went to SOAMANAGER and configured the necessary binding. The bgRFC settings were missing - went to SRT_TOOLS and configured all of it.
While testing it with SOAMANAGER it work fine the first time. No problems in SRTUTIL and the SLG1 log entries were also perfect.
However, subsequent trials threw up weird results. I always get a http 202. This means that the call is going to the server. The SRTUTIL payload trace vouches for this. But there is no SLG1 entry! The application logic is not being called at all!
I checked all the settings in SRT_TOOLS - no changes. I made no changes whatsoever! It would be great if any of you could offer some help here.

You don't say what VPN you use but for PPTP you need GRE protocol passthrough, without it you can connect but no traffic will pass over the VPN tunnel.
You give VPN clients an IP from the LAN interface "range" in VPN settings?
DNS in VPN settings must be reachable through the VPN (default route is through VPN? - any routing definitions?).

Similar Messages

  • My iphone 6 connects to the car via bluetooth, the music works good, but the phone calles does not work.  It looks like it is working but doesn't.  I have tried in my Hyundai and a Dodge rent car and get the same results.  I updated the last 8.0.2.

    My iphone 6 connects to the car via bluetooth, the music works good, but the phone calls does not work.  It looks like it is working but doesn't.  I have tried in my Hyundai Sonata and a Dodge Dart rent car and get the same results.  I updated the last 8.0.2.  It worked the first day i had the phone, and then i updated to Ios 8.0.2 and it quit working.
    Now when i get in the car, it acts like it is connected and makes the same call it was on after syncing to bluetooth, but it really isn't on a call.  This is happening on both cars.
    Does anyone know if this is the phone and i need to take it to Apple or if there is an issue that Apple is working on getting a fix for?
    My son in law has the exact same phone as me, we both got the on 10/6, he had a Dodge Dart and his is working via bluetooth.
    Someone HELP please, as i consider this a safety issue by not having my calls go to bluetooth.

    We had the same problem, but figure out the solution.
    You MUST have at least 1 song added to your ITUNE!  After you add a free song, then everything else should work as normal!
    Hope this helps!

  • TS3694 pls help my iphone 4 was on activation "required". i jailbroke it then it worked but some of the applications were crashing down,won't open. i tried a lot of tutorials and then error message 3194 came out. stucked in recovery mode,itunes logo. pls

    pls help my iphone 4 was on activation "required". i jailbroke it then it worked but some of the applications were crashing down,won't open. i tried a lot of tutorials and then error message 3194 came out. stucked in recovery mode,and then i use snowbreeze and then it worked!!!! but another problem came, i turned off my iphone then i switched it on again then it stucked in apple logo,.after doing some thing again 1604, 1600 bla bla bla came out..pls help me fix my iphone.

    no help for jailbroken phones here-it's not allowed. good luck.

  • Asked a mo. ago why hot sync appears to work but doesn't--zero responses from Palm so trying again

    hot sync appears to work but doesn't transfer info! Options      dee20002
    Regular Visitor
    Posts: 4
    Registered: 09-10-2008
    Palm Z22
    Message 1 of 7
    Viewed 449 times
    hot sync appears to work but doesn't transfer info! Options      dee20002
    Regular Visitor
    Posts: 4
    Registered: 09-10-2008
    Palm Z22
    Message 1 of 7
    Viewed 449 times
    I admit, it's been awhile since I synchronized.  Just did so, and all appeared right with the world, the handheld made the appropriate noises and showed the appropriate actions and same on the computer (XP, connect as always have through USB).  In other words, they appeared to "talk" and said they were synchronizing.  But my data (like important calendar entries) is simply not there.  Nothing.  Nada.  Nothing recently added.
    I tried repeating it several times.  Yes, I have the system set up so that desktop overrides handheld.  So what's up?  Used this a lot in the past, never had this happen.
    Thanks for any help.
    Using XP and the original hot sync that came with palm and that I've always used--no changes. Help???? 
    Dee
    Post relates to: Palm Z22
    Post relates to: Palm Z22
    Post relates to: Palm Z22

    I'm having the same problem though not with the exact same components. I have a Palm Z22 and Windows Vista--things were going great until a few days ago when I noticed that the palm weren't connecting. The Hotsync process proceeds normally, there are no problems noted in the hotsync log, and yet things do not travel from the computer to the palm and vice versa. I've tried pretty much everything: I know the palm is connected to the desktop, not Outlook; I have tried soft and hard resets; I have uninstalled and reinstalled the software multiple times; I know the username is correct.
    I suspect the problem has something to do with Vista; when I restored my computer to a previous time it started working fine but this morning it stopped again. The computer may be automatically updating in a way that is preventing the Palm Desktop software (verson 4.2) from working. Version 6.2 seems to work but I really hate it--there's no color schemes or categories. If someone could help me out with this I would really, really appreciate it.
    Post relates to: Palm Z22

  • Scan works, print says it works but doesn't

    Hi all! Everyone seems to have the opposite problem - wireless printing works but scan doesn't. Not me! I can choose "scan" from my printer OR computer interface and it starts right up. Problem is, when I go to print it goes through the "printing" screen then says "print job complete" (no hangups or errors or something in the print queue to delete - it's in the queue then it disappears as though printed), but...no business results on the printer end!
    Before you ask, yes the printer works (can print from SD card inserted directly to printer, or from old computer connected via network). Yes I have turned everything off and back on. Yes I tried downloading the HP print & scan doctor, and it says everything is fine, sees ink levels etc, but its test page behaves the same as any other print job. Yes I have deleted the whole HP shebang and re-downloaded and re-searched/connected my computer via the wireless network. And, as aforementioned, it scans. Oh, and tells me my ink levels! So clearly there is communication, just not for this. What weird sub-setting am I missing?
    And also, if you can resolve this, can you give me an idea whether it is suddenly going to start printing the 80 pages or so that I've tried to beam over, so I can stop it? : )
    Thanks muchly!
    This question was solved.
    View Solution.

    Hi @theshrew 
    Please try bypassing the spooler to see if you can print directly to the printer.
    1. Click on start and go to devices and printers.
    2. Right click on  the printer and click on printer properties.
    3. Choose the option "Print directly to the printer".
    4. Click apply and then ok.
    If this works follow the next steps and try to print again.
    Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box
    Type services.msc and press Enter
    Locate Print Spooler and double click on it to open the Spooler properties 
    Make sure startup type is set to Automatic, if it is not please click on the drop down and choose Automatic
    Under Service status, please Stop the server, and then wait a moment and click Start
    If bypassing the spooler does not result in a successful print, let me know.
    Also, what printer model do you have?  How Do I Find My Model Number or Product Number?
    Are you getting any error message, or does a blank page print? The more detail I have the better
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • My microphone is not working but only for calls

    I had my Iphone working perfectly until I updated to 4.3.1 after that I lost the microphone but only for calls when I use Skype, Video recording and may other features that uses microphone all of them worked. I did restore again to 4.3.1 and make a new fresh installation without recovering my data so now I'm not only without phone features but also need to load all of my data again. This occurs most of the time but about 2 of 10 calls the people can hear me so I think this must be related to baseband update or hadware issue.

    Might try setting the option in System Preferences > Sound > Input tab > check "use ambient noise reduction"
    Regards,
    Captfred

  • CSS problem that works but doesn;t

    I am beginning to think this is not possible. The code is
    below. The images are their but the two side ones are not showing
    up or they do not even work like the top leaves. I even dropped the
    2 layers lft & rgt inside the top layer that does work and the
    top layer still works but the other 2 still don't, puzzling. Here
    are the link
    http://www.lasalleboat.org/index2.htm
    On number 2 the links do not work the leaves layer/DIV/AP
    Element is above the links layer
    http://www.lasalleboat.org/index3.htm
    On number three the links work but they move over the graphic
    and the links layer is above the leaves layer
    I have tried adding two more layers one on each side of the
    page and put thin graphics.png in the layers so they clear the
    links and made the leaves graphic crop at the bottom of the trees
    line so it cleared the links neither of the two layers I added will
    work or show up withe code below so I tried putting the two lft
    & rgt layers inside the leaf layer and resize the leaf layer
    and that kind works but not you can see this at the next link.
    http://www.lasalleboat.org/index4.htm
    Any suggestions welcome.
    INVT
    Attach Code

    You can take sniffer trace for working one and failing one. Then compare the difference.
    Perhaps, you show us the config for the content rule doing rediretion. (i.e. content rule and its redirection service).  Then I will have a second look.

  • MacBook water spill - works but doesn't charge. Apple doesn't do partial repairs?

    I spilled some water on my MacBook Pro (15in retina).
    I let it dry for a couple of days then powered it. It worked.
    When the battery got to 0%, I plugged the MacSafe and it didn't charge. It sometimes charges, but intermittently. It charges very rarely.
    I brought the laptop to the Apple Store, and they said that it would cost $2000 to repair, because they want to replace EVERY parts that were water stained.
    I only want to change the Adapter Port, and POSSIBLY the Logic Board IF changing the Adapter Port didn't fix the charging issue. Knowing the above, it will most likely work, but if it doesn't, that's OK, I'll buy a new one. I'd rather risk $3-400 by doing this and buying a new Macbook IF it fails, than paying 2K for a repair straight away.
    Of course my laptop could break eventually if not all parts are replaced, but that's fine (I was able to wash some water stains with alcohol already).
    Why doesn't Apple simply change the parts that must be changed, letting the customer take a risk or whatever if he wants so?
    IMO -- Terrible policy that must be reviewed.

    This is a user to user forum and we are not Apple employees.  You may register your thoughts here:
    https://www.apple.com/feedback/
    Ciao.

  • No mouse pointer when connected to TV Samsung led40/6500. Mouse works but doesn't show?

    Just bought Mac Mini. Connected to Samsung 40/6500 ledtv. using mouse pad but no pointer seen. Finally found the resolution working, but not the right resolution. Should be 1920x1080 @ 60 hz via HDMI. Mac Mini's best is much different from this. How can I find the right resolution on my Mac Mini.

    It actually works fine on my sons Lumatron cheap tv! But not on the Samsung led tv?
    To start with I used an app on my Iphone to recieve the image from the Mac Mini and then try to find the right resolution on the MAC. Because every time I choose the wrong one the display went black. I could then still see the image on my phone and troubleshoot my way through...

  • Install 10.4.11 using TDM from G5 to G3.. works, but doesn't take

    I cannot use the Installer app, as I said above, will not even open - it just crashes. So, my plan was to put the G3 in TDM with my G5, and run the "combo" updater on my G5 and point it to my G3. That works perfect just as it should.
    BUT, when you then cycle the power on the G3 at the end of the install and reboot it, the "combo" update has not taken. Everything seemed to work perfect when I did the install.. but the G3 just does not take it as when I reboot, I am in the same broken 10.4.11 I had from the "incremental" update.
    I know this fix of using the "combo" updater will work, as I said did it on another system, but the question is why the G3 is not taking the update despite everything indicating it did? what gives? I would not have to do this if the Installer app worked, but it is hosed.

    I know this fix of using the "combo" updater will work, as I said did it on another system, but the question is why the G3 is not taking the update despite everything indicating it did? what gives?
    Sorry, you are jumping to the wrong conclusion... it WILL work if something is damaged in the parts of the OS that are replaced by the Combo Updater, but clearly WILL NOT if a part of the OS is damaged that was never Updated!
    Appears to be time for An Archive & Install, which gives you a new OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space...
    http://docs.info.apple.com/article.html?artnum=107120

  • Mighty Mouse works but doesn't grab within applications

    I have been a happy and privileged user of Apple products for many years now, I just upgraded to Snow Leopard and suddenly my wireless mighty mouse went funny on us. It moves around, you can grab programs and go into main menu but when you're in the application or menu...it doesn't grab and do what it is supposed to do. I have two wireless mice...both do the same. Changed the batteries as well...same thing. Re-installed software driver...no difference, Rebooted Bluetooth...no result either, did not find anything within preferences either. Called Apple Technical center who was unable to help. Has anyone experienced similar experience and eventually found a solution? Thanks in advance

    Pav1966,
    Welcome to the discussion board!! If you've recently converted to Snow Leopard you might want to double check the mouse settings in System Preferences > Mouse.
    For the Mighty Mouse setting the left side to "primary button" and the right side to "secondary button" is probably what you are use to.
    Make sure the "double-click" slider is not set too fast. That might be why you can't "grab" anything. Set the slider no more than 3/4 up to fast. A slower setting might serve you better.
    Regards,
    Captfred

  • VLC Downloads fine but doesn't open application. Please help

    Hi
    Can someone please help me with my downloading problem? Excuse me if I sound like a tard but I'm really keen on learning. I searched through previous posts but didn't quite find what I was looking for.
    I download fine. Copy into applications. Everything looks good but it won't kick off. All I get is a flash of the application logo on the dock and then nothing, it disappears. I wanted to download (VLC vlc-0.8.6a.dmg) and Last.Fm (LastFMMac1.1.3.0.dmg) but no dice.
    I have downloaded in the past just fine, but only minor things like Limewire and Quicksilver, they work okay. I'm confused any help would be greatly appreciated.

    Hi ZZ
    vlc-0.8.6a.dmg is for 10.3.9, so that's why it wont open on your OS, which shows your have Mac OS X 10.3.5
    Either find the right one for your OS, or Upgrade to 10.3.9, hardly worth it, just to play the odd video in VLC, but they are your choices.
    I did some hunting for more info for you.
    Why doesn't VLC 0.8.6a work on 10.3, although you state it does?
    "First of all, make sure that you got 10.3.9 installed. Any earlier release, particularly 10.3.5 and below, doesn't support current versions of VLC. Additionally, while QuickTime 6.5.2 is strictly required, QuickTime 7.x is strongly recommended for performance and usability reason"
    So it doesn't look like there is an earlier version.
    If you want to use it, you must upgrade to 10.3.9.
    regards roam
    Message was edited by: roam

  • OK icacls command that should work but doesn't.

    icacls "c:\windows\system32\spool\PRINTERS" /grant administrators:(IO)(CI)(OI)F /t 
    When some of my systems go to print a PDF the spooler just locks up.  I can't control what type of PDF files are coming in as they are made by all kinds of software and so the problems begin.  I have been working on a batch file that will stop
    the spooler service if it hasn't already, then run the above command to grant rights to the indicated directory so that the offending files can be deleted from the spooler and restart the spooler service after that has happened.  The reason for this is
    that by default a user can't go in and delete the files.  I believe that I have the command correct and it used to work fine in Windows XP and Windows 7 but I can't see why it doesn't work in Windows 8. 
    Here is the batch file.  Please tell me what I have wrong in it.
    net stop spooler
    timeout/t 3 /nobreak
    icacls "c:\windows\system32\spool\PRINTERS" /grant administrators:(IO)(CI)(OI)F /t
    c:
    cd\windows\system32\spool\PRINTERS
    Del *.s*
    timeout/t 3
    net start spooler
    exit 

    If you run icacls "c:\windows\system32\spool\PRINTERS" /grant administrators:(IO)(CI)(OI)F /t manually,
    what output do you get and what is the resultant ACL on the files?
    Also, you shouldn't use the /t switch - it tells icacls to recursively apply that ACE for every subitem
    in that folder rather than let NTFS handle it via inheritance. The only time you should use it is when you really need to apply a specific ACE explicitly to all items in a folder, for instance: 
    icacls "C:\temp" /grant administrators:F /t
    The above command will explicitly grant Administrators full control on every item in that folder (this
    item only - no inheritance).

  • ALSA works, but only with one application at a time.

    Hello,
    Before I continue my post, I would like to say that I have read this section on the wiki:
    https://wiki.archlinux.org/index.php/AL … ack_Issues
    It asks the user to edit /etc/asound.conf (which does not exist) in order to comment out a few lines that will fix the problem. It's quite frustrating to need to close all audio using programs every time I want to play audio. I do not have pulseaudio installed. I tried installing OSS4 in order to fix the problem, but for some reason my kernel headers were not detected and I couldn't start the daemon. I would appreciate it if someone could reply to me and tell me what the problem could be.
    Thanks,
    Dragos

    I'm using a part of your config right now. It doesn't appear to be working correctly, or perhaps I'm not looking at the right section?:
    pcm.dmixed {
    type asym
    playback.pcm {
    # See plugin:dmix at http://www.alsa-project.org/alsa-doc/alsa-lib/pcm_plugins.html
    type dmix
    ipc_key 5678293
    ipc_perm 0660
    ipc_gid audio
    # Don't put the rate here! Otherwise it resets the rate & channels set below, as shown by: cat /proc/asound/card0/pcm0p/sub0/hw_params
    slave {
    # 2 for stereo, 6 for surround51
    channels 6
    pcm {
    # mplayer chooses S32_LE, but others usually S16_LE
    #format S32_LE
    format S16_LE
    # 44100 or 48000
    #rate 44100
    rate 48000
    type hw
    card 0
    device 0
    subdevice 0
    # mplayer2 chooses 1024
    # period_size 512 with buffer_size 16384 stops crackling in xmame
    # 320 breaks flash - https://bbs.archlinux.org/viewtopic.php?id=129458
    #period_size 512
    period_size 1024
    # 2730 is chosen by "speaker-test"
    #period_size 512
    #period_time 20000
    #periods 8
    # 4096 makes Thief 1 in wine crackle.
    # mplayer2 chooses 8192
    #buffer_size 5460
    # 5460 (2730*2) is too small for mplayer2
    # If too large, use CONFIG_SND_HDA_PREALLOC_SIZE=2048
    buffer_size 8192
    #buffer_size 4096
    #buffer_time 682667 # 32768 samples at 48 kHz, in µs
    # 16384 seems best to stop crackling in Skype
    #buffer_size 16384
    # Seems good
    #period_size 256
    #periods 16
    #buffer_size 16384
    # Old config
    #buffer_size 10240
    #period_size 2048
    # Other options to maybe play with:
    #period_time 2
    #periods 2
    bindings {
    0 0
    1 1
    2 2
    3 3
    4 4
    5 5
    capture.pcm "hw:0"
    pcm.!surround51 {
    type plug
    slave.pcm "dmixed"
    This is my asound.conf file. I'm sorry if I'm not finding the section you were talking about.
    Thanks,
    Dragos

  • Quicken works but doesn't show up in Dock

    Quicken 2000 v.16.1.2 does work in Mountain Lion, but it does NOT show up in the Dock or in Application Switcher (Command-Tab).

    Does this happen with other applications?
    Try opening a Terminal window and typing:
    killall Dock
    Which will restart the Dock.  I bet it shows up.  Other folks have had issues with this and it's usually the Dock has crashed.

Maybe you are looking for